OWNER'S MANUAL SLT-330F Scissor Lift Table JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000 A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840 www.jettools.com e-mail jet@jettools.com M- 140771 11/00
Important Information 1-YEAR LIMITED WARRANTY JET offers a one-year limited warranty on this product REPLACEMENT PARTS Replacement parts for this tool are available directly from JET Equipment & Tools. To place an order, call 1-800-274-6848. Please have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiration date 3. Part number listed within this manual 4. Shipping address other than a Post Office box. REPLACEMENT PART WARRANTY JET Equipment & Tools makes every effort to assure that parts meet high quality and durability standards and warrants to the original retail consumer/purchaser of our parts that each such part(s) to be free from defects in materials and workmanship for a period of thirty (30) days from the date of purchase. PROOF OF PURCHASE Please retain your dated sales receipt as proof of purchase to validate the warranty period. LIMITED TOOL AND EQUIPMENT WARRANTY JET makes every effort to assure that its products meet high quality and durability standards and warrants to the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship as follows: 1 YEAR LIMITED WARRANTY ON THIS JET PRODUCT. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities or to a lack of maintenance. JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE FROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MECHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY OR FOR INCIDENTAL, CONTINGENT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. To take advantage of this warranty, the product or part must be returned for examination, postage prepaid, to an authorized service station designated by our Auburn office. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, JET will either repair or replace the product or refund the purchase price, if we cannot readily and quickly provide a repair or replacement, if you are willing to accept such refund. JET will return repaired product or replacement at JET s expense, but if it is determined there is no defect, or that the defect resulted from causes not within the scope of JET s warranty, then the user must bear the cost of storing and returning the product. This warranty gives you specific legal rights, and you have other rights, which vary, from state to state. JET Equipment & Tools P.O. Box 1349, Auburn, WA 98071-1349 (253) 351-6000 2
WARNING 1. Read and understand the owner s manual before using scissor lift table. 2. Do not load scissor lift table beyond its rated capacity. 3. Do not allow people to sit or ride on scissor lift table. 4. Secure load before raising or moving scissor lift table. 5. Do not transport loads in the raised position. 6. Use only on smooth, level, finished floors. 7. Pull release lever slowly to allow load to descend in a controlled manner. 8. Keep hands and feet clear of table when lowering load. 9. Failure to comply with the above warnings may result in personal injury and/or pro perty damage. Specifications: SLT-330F Stock Number...140771 Capacity... 330 lbs. Maximum Height... 28-3/4" Minimum Height... 8-5/8" Table Length... 27-1/2" Table Width... 17-3/4" Overall Length... 36" Handle Height... 34-1/8" Number of Strokes without load to Reach Max. Height (approx.)...16 Net Weight (approx.)... 91 lbs. Shipping Weight (approx.)... 99 lbs. Operation Maintenance Note: The scissor lift table comes preassembled and ready to use. However, during transit air may have seeped into the pump. To bleed air out of hydraulic system, raise and lower the table several times to work any air bubbles out of the pump. 1. The table is raised by pumping the foot lever (B, Fig. 1). 2. To lower the table, slowly pull the release lever. 3. Before loading, always lock the caster brake by pressing the lock (A, Fig. 1). Folding Handle 1. Lower the table. 2. Push the rod (C, Fig. 1) back. 3. Fold the handle flat across the table. 1. Lubricate each friction point monthly with #2 tube grease. 2. Check the movement and wear of wheels. 3. Check for oil leakage from the hydraulic cylinder. Add hydraulic oil as needed. 4. Always store with table in lowered position when not in use. 3
SLT-330F Trouble Shooting Note: the numbers in parenthesis refer to index numbers located on parts breakdown, page 5. Trouble Cause Action No oil in pump reservoir. Replenish pump reservoir. Table will not raise. Lowering valve (28) or steel ball (25) is not seating. Steel ball (20) is not seating. Clean lowering valve (28) or steel ball (25) or replace. Clean or replace steel ball (20). Table will not remain elevated. Table will not lower. Release valve is not adjusted properly. Lowering valve (28) or steel ball (25) is not seating. Oil seal (6) or U-packing (7) is worn out. U packing (7) is worn out. Lowering valve plug (28) is clogged. Reload truck within load capacity and adjust valve by pressure release adjusting screw (31). Clean or replace lowering valve (28) or steel ball (25). Replace oil seal (6) or U-packing (7). Replace U-packing (7). Replace lowering valve plug (28). Oil leaks from lowering valve. O-ring (27) is worn out. Replace O-ring (27). Oil leaks from pump cylinder. Oil seal (33) or U-packing (32) worn out. Replace oil seal (33) or U-packing (32). 4
Breakdown for SLT-330F Hydraulic Scissor Lift Table 5
Parts List for SLT-330F Hydraulic Scissor Lift Table Index Part No. No. Description Size Qty 1... SLT330F-01... Table......1 2... SLT330F-02... Shaft......4 3... SLT330F-03... C-Ring... 12...4 4... SLT330F-04... Link Assembly......1 5... SLT330F-05... Roller Guide......4 6... SLT330F-06... Release Lever......1 7... SLT330F-07... Cable......1 8... SLT330F-08... Handle......1 9... SLT330F-09... Foot Lever......1 10... SLT330F-10... Frame......1 11... TS-1490111... Hex Cap Bolt...M8X60...4 12... SLT330F-12... Bushing......4 13... SLT330F-13... Bearing......4 14... SLT330F-14... Wheel......4...... Wheel Assembly (Inclds: 11-15)......2...... Swivel Caster Assembly (Inclds: 11-15,19)...2 15... TS-1540061... Hex Nut...M8...2 16... TS-1550061... Flat Washer...M8...8 17... TS-1551061... Lock Washer...M8...8 18... TS-1490011... Hex Cap Bolt...M8X12...8 19... SLT330F-19... Wheel Holder......2 20... TS-1541031... Nyloc Nut...M8...2 21... SLT330F-21... C-Ring... 8...4 22... SLT330F-22... Lock Pin......4 23... SLT330F-23... Spring......2 24... SLT330F-24... Shaft......1 25... SLT330F-25... C-Ring... 12...1 26... SLT330F-26... Cylinder Assembly......1 [1]... SLT330F-26-1... Oil Seal *......1 [2]... SLT330F-26-2... Top Nut... 25...1 [3]... SLT330F-26-3... O-Ring *... 31.35...1 [4]... SLT330F-26-4... Lift Piston......1 [5]... SLT330F-26-5... Piston Bushing......1 [6]... SLT330F-26-6... O-Ring *... 35X3.5...1 [7]... SLT330F-26-7... U-Packing *... 35...1 [8]... SLT330F-26-8... C-Ring... 18...1 [9]... SLT330F-26-9... Air Breather......1 [10]... SLT330F-26-10... O-Ring *... 11X1.9...1 [11]... SLT330F-26-11... Relief Plug......1 [12]... SLT330F-26-12... O-Ring *... 11X1.9...1 [13]... SLT330F-26-13... Relief Adjusting Screw......1 [14]... SLT330F-26-14... Spring......1 [15]... SLT330F-26-15... Steel Ball Support......1 [16]... SB-5MM... Steel Ball...5mm...1 [17]... SLT330F-26-17... Valve Plug...M16X2...1 [18]... SB-12MM... Steel Ball...12mm...1 [19]... SLT330F-26-19... Spring......1 [20]... SB-9MM... Steel Ball...9mm...1 [21]... SB-6.5MM... Steel Ball...6.5mm...1 [22]... SLT330F-26-22... Screw......1 [23]... SLT330F-26-23... O-Ring *... 14X2.4...1 [24]... SLT330F-26-24... Spring......1 [25]... SLT330F-26-25... Steel Ball......1 6
Index Part No. No. Description Size Qty [26]... SLT330F26-26... Spring......1 [27]... SLT330F-26-27... O-Ring *... 10X1.9...1 [28]... SLT330F-26-28... Lowering Valve......1 [29]... SLT330F-26-29... O-Ring *... 26X2.4...1 [30]... SLT330F-26-30... Pump Cylinder......1 [31]... SLT330F-26-31... O-Ring *... 22X2.4...1 [32]... SLT330F-26-32... U-Packing *... 18...1 [33]... SLT330F-26-33... Oil Seal *... 18...1 [34]... SLT330F-26-34... Pump Piston......1 [35]... SLT330F-26-35... Cylinder......1 27... SLT330F-27... Fix Seat......1 28... TS-1551031... Lock Washer...M5...2 29... SLT330F-29... Lock Pin......1 30... TS-1540061... Hex Nut...M8...1 31... TS-1504061... Socket Head Cap Screw...M8X30...1 32... TS-1524061... Socket Set Screw...M8X25...1 33... TS-1540061... Hex Nut...M8...1 34... SLT330F-34... Fixed Board......1 35... TS-1502041... Socket Head Cap Screw...M5X14...2 36... SLT330F-36... Shaft......1 37... SLT330F-37... Spring......1 38... SLT330F-38... Spring Cover......1 39... SLT330F-39... Slide Lever......2 40... SLT330F-40... Lock Pin......1 41... SLT330F-41... Lock Pin......1 42... SLT330F-42... Bushing......1 43... SLT330F-43... Lock Pin... 3X20...2 44... SLT330F-44... Lever......1 45... TS-1490031... Hex Cap Screw...M8X20...1 46... TS-1551061... Lock Washer...M8...1 47... TS-1550061... Washer...M8...1 48... SLT330F-48... Foot Lever......1 49... SLT330F-49... Foot Lever Pad......1... SLT330F-RK... Repair Kit......1 Index Numbers with brackets [ ] are part of the hydraulic pump assembly. Parts included in the repair kit are indicated by an asterisk *. 7
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000 A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840 www.jettools.com e-mail jet@jettools.com 8