A TechForAg 'Ready-To-Milk' Modular Parlor Model: Dbl. 12 Thorp/Germania ParaBone Key Features: Conventional Exit - Automatic Indexing - 30" Cow-to-Cow Distance This parlor should milk from 80 to 100 cows per hour with one Milker Prepared For: Website Parlor # 122 - Proposal # 070617 # 11 Please Note: If the Quantity in the very left column is shown as - 0 - that item is not included, i.e. no cost shown in the right hand column either Page 1 of 20
Qty Units Description Cost to Enduser 24 Stalls Continous Splash Shield - Stainless - 30" spacing $ 3,429 Page 2 of 20
4 Entrance and Exit Gates 2 1/2 x 2 1/2 x 11ga tubing $ 1,714 Automated Cow Traffic Controls 1 Group - (2) 3" x 10" Entrance Gate Cylinders - (2) 3" x 10" Exit Gate Cylinders - (4) 3" x 10" stainless Cylinders for Auto Indexing $ 4,286 Cow Traffic Controls at last stall on either side of parlor Stainless Cylinders operate Entrance & Exit Gate Page 3 of 20
24 Stalls Galvanized Blue Diamond Brisket Bars Rapid Exit! With Automatic Indexing $ 13,500 Page 4 of 20
4 Units Brisket Bar Support Posts $ 2,857 Page 5 of 20
24 Stalls Stainless Gutter, Stainless Curbing - both New! Galvanized Original Germania Grates - Remanufactured $ 8,777 Page 6 of 20
Original Germania/RoKa C No-Arm TakeOffs Remanufactured 24 Units Remanufactured but with high percentage of new parts All-Air controlled, All-stainless construction $ 20,400 RoKa Model RC No-Arm TakeOffs All-Air operated - No Electronics! Ultimately Reliability! Page 7 of 20
Germania Top Outlet Claw - Remanufactured 24 Units - Air Forks - 06 Shells - 60" Milk Hose - 108" Pulsation Hose - Short air tubes - Liners of your choice: Brand & Model $ 11,853 We developed this claw in 1978, the original Germania Top-Outlet Claw and have made it in its original form ever since (Picture on the right is not the correct CIP Cup Holder. These are optionally available, see last page) Page 8 of 20
24 Units Counterweighted Hose Supports $ 1,543 Pulsation System - New! 24 Stalls - 3" PVC Pulsation line with hoses, fittings & wiring harness - 3" PVC FreshAir line with fittings & hoses - (4) FreshAir Filters, three per side - (2) 3" PVC Cross-Overs in front & back - Pulsators iuncluded with Claw-Clusters $ 1,886 16-Unit Excalibur Pulsation Controller 3 Units Electrician provides 120 volt receptacle nearby - bid separately! $ 2,786 Page 9 of 20
80 ft 3" Lo-Line Incl. all brackets, nipples, clamps and gaskets Single loop, double slope line 2" CIP Lines Incl. all brackets, nipples, clamps and gaskets $ 5,143 80 ft From the CIP group in the milk house to the back of the parlor. $ 2,857 2" Discharge line - New! 60 ft from Receiver Group to Milk Tank. Includes special adapters at Tank and Safety Switch. $ 2,143 Page 10 of 20
0 Group 0 Group Traditional Receiver Group, with Partially New, Partially Remanufactured Components, incl. - 26" x 26" Receiver (2) 1 1/2 hp Milk Pumps, 2nd Pump is Stand-By Ball Check valve 3" x 3" Moisture Trap & U-Bend LL Probes and Controller Long Plug - Short Plug 1" Air Injector; Vacuum operated Drain $ - Conventional CIP System with Partially New, Partially Remanufactured Components, incl. DeLaval C-125 Pipe Line Washer 3/4" Hot and Cold, Air Operated Water Valves Open Wash Sink Divert Valve and Drain (3) Peristaltic Chemical Pumps $ - Page 11 of 20
Compressed Air System - New! 0 Group (1) 7.5 hp SpeedAir Piston Compressor $ - Electrician provides 430 Volt 3-phase to this group 10 hp Atlas Copco Srew Compressor & 80 gl storage tank for dry air Small Air Prep Group - APP-S - New! 1 Group Includes 1/2" copper lines & fittings to all stations of parlor $ 1,286 Page 12 of 20
15 Hp Vacuum System with Lobe-Style Pump - New! Gardner-Denver/Sutor-Built Pump 0 Units 0 ft Includes Frequency Controllers/Variable Speed Drive designed for 'No Interference' with Cow ID: shielded cable, none metallic enclosure, filtered input, etc., i.e. AfiMilk compatible $ - 6" PVC Header Lines with 3" fittings to Pulsation and 4" adaptors to the CIP / Receiver Group $ - Electrician provides 430 volt 3 phase to this Group 6" Header Line supplies CIP Receiver Group and Pulsation System Page 13 of 20
0 Group On-Farm Spare Parts Kit (Contains only new parts) Includes all essential parts for at least (1) year of operation (2) sensors, a retract cylinder, at least (1) of each air valves, an extra LLC, seal kit for the milk pump, PC Board for the PL Washer, several extra Pulsator, etc. $ - 2 x 5-ft Stainless Curb Extensions in Front 11 ft from Exit Gate to Breezeway Wall. Prevents manure from running into the pit; Includes concrete guard. $ 707 0 Pcs Double Compartment Sink - New! $ - Accessories Group - New! 0 Group Hand Wash Sink, Filter Sock Holder with (1) box of Filters, SST paper towel holder, Soap Dispenser, Hose Rack for garden hose in Milk House, etc. $ - Pit Mats for 8 ft wide x 90 ft long pit floor 0 squ ft Page 14 of 20 Color of your choice - Blue, Green, Red or White $ -
0 Unit Stainless Pit Steps - 4 steps, 30" wide - New! $ - (2) 50ft 1" Wash-Down Hose for Cow Platforms 0 ft with solid Brass Firehose Nozzles $ - 0 ft (2) x 20 ft 1" clean-up hoses for the pit $ - 0 Units Traditional CIP Cup Holders $ - Page 15 of 20
0 Unit Stainless Breezeway Fence with (2) 3ft 'Side Wings' - Made from 2.5" x 2.5" square stainless tubing - 10- ft + 3 ft long, with - (2) Horizontals and - (4) 3 ft Verticals $ - 12-Stall Modular Platforms - New! 2 Units The structural bases of the Modules; Height of your concrete cow platform should be 34" - if you are comfortable with a 38" working height. To be discussed! $ 3,429 Page 16 of 20
We build our parlor modules on platforms, a frame work made form 2" x 4" steel tubing and usually 53" wide x 50.6 ft long for the typical dbl. 12. Normally, we slide the Modules into place on this steel frame work, pushed by a Skid Loader. Parlors up to dbl. 12 come on two trucks, all larger ones need four. Page 17 of 20
Summary Page Sub-Total Materials $ 88,594 Less: Dairy-Direct Discount of 26% $ (23,035) Cost of Materials after DDD $ 65,560 Pre-Installation Labor and Supplies provided by TechForAg at it's factory to convert the above materials into a Ready-To- Milk Modular Parlor (calculated at 15% of materials) $ 13,289 2 Trucks Freight - @ $750/truck (In Wisconsin, slightly higher charges elsewhere) $ 1,500 On-Site Installation Labor, Supplies & Expenses $ 8,500 Grand Total Parlor with Freight & Installation $ 88,849 Per Stall $ 3,702 Page 18 of 20
Optionally Available 24 Units Fold-Up CIP Cup Holders Do not need Rubber Cups (To be discussed ) $ 6,686 24 Units 24 Stalls Air-Powered CIP Cup Holders Just push a button - Now you see them - then you don't $ 9,909 1" Kraiburn Rubber Mats (Made in Germany) - New! For the (2) Modular Cow Platforms Plus Freight and Installation $ 3,024 Page 19 of 20
Terms - I If production at TFA starts several months in the future 1) 15% down at signing of contract 2) 35% on start of production 3) 45% on delivery of parlor to the dairy 4) 5% on Start-up of Milking 4) $1,000 Rebate for prompt payment Terms - II If production at TFA starts more or less immdiately 1) 35% at signing of contract, plus 2) 25% six weeks later 2) 35% on delievery of parlor to the dairy 3) 5% on start-up of milking 4) $1,000 Rebate for prompt payment Page 20 of 20