LIMITED WARRANT STATEMENT SPAL USA WARRANT STATEMENT Our most popular kit comes complete with (1) seven-channel receiver, () remote transmitters and () solenoids with 0 pounds of pull each. This kit also includes all necessary hardware for installation. The kit offers enough pull to open virtually any door on the market today. SPAL USA warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of sale to the original purchaser, and not more than two () years from the date of manufacture. SPAL USA will repair this product free of charge if, in the judgment of SPAL USA, it has been proven defective within the warranty period. The product should be returned, at the customer expense, to the location of original purchase. This warranty does not cover any expenses incurred in the removal and/ or reinstallation of the product.this warranty does not apply to any product damaged by improper installation, accidental misuse, abuse, improper line voltage, fire, flood, lightning, or other acts of God, or a product altered or repaired by anyone other than SPAL USA.This warranty is in lieu of other warranties, expressed or implied, including any implied warranty of merchantability. No person is authorized to assume for SPAL USA any other liability concerning the sale of this product. IMPORTANT-KEEP OUR INVOICE WITH THIS WARRANT STATEMENT!
Terminal Switch 1ga Wiring FEATURES: 1) ) the control period, the lock pulse timer will prevent the device(s) from being damaged. 3 by shutting down the system for seconds if the buttons on the key fob (transmitter) are activated more then 8 times in a second period. After the second time-out period, the system will function as normal. ) >>> PLEASE NOTE! <<< Power and ground to the 10-PIN connector must be hooked up to the control module for the unit to operate correctly! Antenna 1 Long (Do Not Ground Or Cut) - Transmitters (Replacment Part - 0lb Solenoids OPERATION: 10-PIN MATING CONNECTOR 937-10 CAVIT CIRCUIT WIRE COLOR FUNCTION 1 Ground Black To Ground Not Used Green --- 3 Channel 7 Purple Negative Output Accessories Channel Blue Negative Output Channel 3 Orange Negative Output 6 +1V Red To Power 7 Ignition ellow To Ignition Power 8 Not Used Grey --- LED (Red) Ring Terminals () ellow Butt () Blue Butt 9 Channel 6 White/Black Negative Output 10 Channel Brown Negative Output FUNCTIONALIT: nels 3 through 7 are controlled by negative output wires (see page # SPADE TERMINALS (POSTION 1 IS CLOSEST TO 10-PIN CONNECTOR) MATING CONNECTOR.0 FEMALE TERMINAL POSITION CIRCUIT WIRE COLOR 1 Not Used Violet Not Used Orange 3 1V Red Channel 1 Brown Channel ellow 10 9 1 3 Spade Terminals 8 3 10-Pin Connector 7 6 1 1
PROGRAMMING: 1) The kit can accept up to () transmitters. Kit comes complete with (). Replacements ) The transmitters that come with the kit are pre-programmed to the main 3) instructions: A) B) C) Press the programming button quickly 3 times. The led will light steady. D) Press button #1 on each transmitter you wanted learned into the receiver (one at a time will flash each time a transmitter has been successfully programmed. E) After the last transmitter has been programmed, wait for the led to go out. Then test each transmitter for proper funtioning. JUMPER, DIP SWITCH SETTINGS & TRANSMITTER SETTINGS: All dip switches to be in the off position BUTTON #1 the lock function - channel 1 BUTTON #3 the function for channel 3 Programmed to control module 1 3 BUTTON # the unlock function - channel BUTTON # the function for channel EMERGENC-BACKUP SWITCH (INCLUDED IN KIT): 1) STRONGL RECOMMENDED that an emergency-backup switch be mounted outside the vehicle in the event of lost transmitters, loss of power or your keys get locked inside the vehicle. ) See the suggested wiring diagram: Emergency Backup Switch 0lb Solenoid To Chassis Ground RECOMMDATION: Locate 3amp Fuse/Fuse Holder Within 18 Of Battery. Fuse Holder Not Supplied & Must Be Purchased Separately. MOUNTING / WIRING: 1) ) 3) (The door is not a proper grounding source!) **A mechanical backup switch should be utilized in case of power failure.** MOUNTING & WIRING: *BATTERIES INCLUDED Repacement batteries can be ordered from: GP7A / LR3A www.radioshack.com ADDITIONAL CHANNELS BUTTON #1 & # the function for channel BUTTON #1 & #3 the function for channel 6 BUTTON #1 & # the function for channel 7 1) ) 3) When using the control module with SPAL actuators (instead of the 0lb solenoids) ) ) Connecting the yellow ignition wire will disable channels 1- while the ignition is on. 1. Max Extension From Fully Compressed Black / Connect To Ground Door Latch Mechanism Arm Cable Clamps Brown or ellow Wire Of Receiver STANDARD SETUP REVERSE PULL SETUP 3
WIRING OPTIONS FOR CHANNELS 3 THROUGH 7: WIRING OPTIONS FOR OPENING TRUNK USING OUR : ITEM TO BE ACTIVATE Any Channel 3-7 From Molex Connector DESCRIPTION OF FUNC- TION A + 1 VDC 8 RELA TPE + 1 VDC Output # OF RELAS REQUI B AT T E R DIAGRAM 1 Power Window Motor Move Window Up & Down SPDT Reverse 1 Power Window Motor Move Window Up & Down SPDT 1 Reverse Linear Actuator Move In & Out SPDT Reverse Solenoid Activate Solenoid SPST Or SPDT 1 Positive Or Negative Trunk Release Open The Trunk SPST Or SPDT 1 Positive Or Negative Door Lock Actuator Lock & Unlock SPDT Reverse SPST / Single pole single throw relay, amp or 0amp. SPDT / Single pole double throw relay, amp or 0amp. Relays can be purchased from SPAL USA (Part #HR-SC-RELA) or from your local auto parts store. POSITIVE OUTPUT: NEGATIVE OUTPUT: + 1 VDC 8 ORANGE A IGNITION: WHEN IGNITION IS PRESENT CHANNELS 1 THROUGH ARE DISABLED + 1 VDC CHANNEL 3 OUTPUT FROM RECEIVER TRUNK SOLENOID POSITIVE TRUNK RELEASE SOLENOID: 8 ORANGE + 1 VDC A B A T T E R IGNITION: WHEN IGNITION IS PRESENT CHANNELS 1 THROUGH ARE DISABLED CHANNEL 3 OUTPUT FROM RECEIVER + 1 VDC TRUNK SOLENOID NEGATIVE TRUNK RELEASE SOLENOID: Any Channel 3-7 From Molex Connector A 8 + 1 VDC Ground Output B ATT E R 6
REVERSE POLARIT OUTPUT: **IN A REVERSE POLARIT SSTEM, A SWITCH THAT RESTS AT MUST BE USED!** MINIMUM INSTALL REQUIREMENTS: For power windows, two relays must be placed between the switch and the window motor. The dashed line indicates where the wires must be cut. + 1 VDC A Any Channel 3-6 From Molex Connector 8 B R A TT E IGNITION: WHEN IGNITION IS PRESENT CHANNELS 1 THROUGH ARE DISABLED (OPTIONAL) S W 3 BROWN A 8 DRIVER DOOR (CHANNEL #1) PASSENGER DOOR (CHANNEL #) WHITE WHITE TO KICKPANEL TO KICKPANEL I T C H Any Channel 3-6 From Molex Connector POWER WINDOW MOTOR 7 8