HP30 Slab Saw Owner s Manual and Operating Instructions MADE IN USA Revision 07 09.0 Manual Part No. 67 Caution: Read all safety and operating instructions before using this equipment. This manual MUST accompany the equipment at all times. Barranca Diamond Products, Inc. 3 Storm Parkway Torrance, CA 900 Toll-Free: (00) 630-76 Phone: (30) 3-67 Fax: (30) 7-3063 www.barrancadiamond.com
HP30 EXPLODED VIEW HP30 Slab Saw Part# 60 6 3 0 6 3 9 3 33 3 3 3 7 3 9 39 0 37 30 3 6 36 0 6 0 7 7 0 9 9 7 6 ITEM DESCRIPTION PART # QTY. NUT, HEX, 3/ - 6 0 NUT, HEX, /6-096 3 HOSE, VINYL, /X3/ TSAW 39 SCREW, HEX HEAD, / - 0 X / 00 WASHER, FLAT, SAE, 3/ 093 3 6 WASHER, 3/ LOCK, SPLIT 09 7 WASHER, LOCK, SPLIT, /6 77 WASHER, FLAT, SAE, /6 7 6 9 NUT, HEX, / -0 93 0 WASHER, FLAT, SAE, / 9 36 SCREW, HEX HD, / - 0 X 3/ 370 6 SCREW, RND HD, #-3 X X / 7 3 SCREW, 3/-6 X -/ HEX HEAD 3 SCREW, HEX HD, CAP, 3/ -6 X -/ 39 6
HP30 PARTS LIST HP30 Slab Saw Part# 60 ITEM DESCRIPTION PART # QTY. COLLAR, SHAFT, 3/" I.D. 3 6 SCREW, HEX HD, /6-X-/ 390 7 SCREW, FLAT HD, /-0 X 3/ 67 SCREW, PAN HD, CAP, /-0 X / 7 9 WASHER, FLAT, SAE, # 0 BLADE, 30", 303 673 SCREW, 3/-6 X -3/ HEX HD 39 6 CONNECTOR, CORD, LTF 9 3 WASTER PUMP V/60HZ 300 GPH 6009 BEARING, FLANGE, -BOLT, " SHAFT 6363 BUSHING, BRONZE FLANGED 3/ X / X -/ 637 6 GEAR, SPUR, BRONZE " OD, RAW 677-RW 7 NUT, WING FLANGE 3/ - 6 67 WHEEL, CASTER 3 X -/ 63 9 WHEEL, CASTER 3 X -/ 679 30 TABLE, ARBOR 693 3 NUT, HEX "-UNF 603 3 CORD, POWER ASSEMBLY, ON/OFF SWITCH 660 33 LEVER, ON/OFF SWITCH 66 3 CHAIN, ON/OFF SWITCH 66 3 GROMMET, ON/OFF LEVER 663 36 COVER, GEAR BOX 6670 37 LATCH, HOOD 669 3 SCREW, FLAT HD, PHILLIPS 0-3 X 3/" 6696 39 GASKET, BEARING 6709 0 ASSEMBLY, DRIVE SHAFT 67366 GASKET, GEAR BOX 67373 TABLE TOP 67670 3 SHAFT, ARBOR, HP- 6767 WELDMENT, TANK 60 ASSY, VISE 607 6 FLANG, BLADE, " 609 7 WELDMENT, BELT GUARD 609 ASSEMBLY, SPRING GAS LIFTING 6 9 ASSEMBLY, ON/OFF SWITCH 66 0 ASSY, HOOD 7309 7
HP30 PARTS LIST HP30 Slab Saw Part# 60 0 3 7 9 0 3 7 9 6 3 6
HP30 EXPLODED VIEW HP30 Slab Saw Assy. Bottom Part# 60 ITEM DESCRIPTION PART # QTY. NUT, HEX, 3/-6 0 PULLEY, A X /" BORE 337 3 WASHER, FLAT, SAE, 3/ 093 WASHER, FENDER, /6 X.0 03 SCREW, HEX HD, CAP, /6- X 3/ 369 6 6 WASHER, FLAT, SAE, /6 7 7 NUT, HEX, /-0 93 SCREW, HEX HD, TAP, /-0X 676 9 SCREW, HEX HD, /6-X-/ 390 0 TAG, SERIAL NUMBER, BLANK 700-RW BELT, A 6 PULLEY 6" OD. " BORE 677 3 PULLEY, STEP CONE 3,, X / BORE 67 SPRING, EXTENSION 6337 CAP, FINISHING 63 6 MOUNT, MOTOR 6699 7 TENSIONER BRACKET 66396 SHAFT, TENSIONER 66 9 PULLEY, ASSEMBLY 666 0 RING, RETAINING /" 667 PULLEY, 9" X " BORE 6736 MOTOR, HP 60HZ 7R.P.M PH 609 3 BELT, A70 607 GROMMET, / X / X / 666 9
HP30 EXPLODED VIEW Vise Assembly Part # 607 6 0 3 9 SCALE 0.37 7 ITEM DESCRIPTION PART # QTY. WASHER, FLAT, SAE, / 9 SCREW, HEX HD, CAP, /-0X -/ 6607 3 SCREW, /6- X 3/ SOCKET HEAD SET 703 NUT, HEX, NYLK, /-0 97 BUSHING, BRONZE FLANGED / X / X 3/ 630 6 SUPPORT BAR, RIGHT 666 7 SUPPORT BAR, LEFT 667 ROD, VISE TRAVEL 67369 9 ROD, THREADED FEED 60 0 SHOE, CLUTCH (COMP) 609 ASSEMBLY, VISE HP-/30 7 30
HP30 PARTS LIST Vise Assembly Part # 7309 3 0 9 7 6 ITEM DESCRIPTION PART # QTY. WASHER, FLAT, SAE, / 9 SCREW, HEX HD, TAP, /-0 X 676 3 NUT, HEX, NYLK, /-0 97 GUARD, SPLASH, NO LOGO 6030-NL NUT, BRASS / NPTF 6 6 WINDOW 66 7 GASKET, WINDOW 663 SCREW, PAN HD PHIL -3 X 3/" SEALING 667 9 WELDMENT, HOOD 606 0 FITTING ELBOW, PUSH ON HOSE / X / MALE 60 3
HP-30 WARRANTY BARRANCA DIAMOND LIMITED WARRANTY Please complete the warranty registration card and return. Any problems encountered should be directed to Barranca Diamond Customer Service department at (00) 630-76 M-F am - pm PST. Barranca Diamond warrants to the original retail purchaser for a period of 90 days except as noted, from the date of purchase all products covered by this Warranty to be free of defects in materials and workmanship. This Warranty shall not apply to any parts that have been subjected to misuse or improper service, that had been damaged in transit or handling, or that have been altered or repaired by unauthorized representatives. This Warranty does not cover defects caused by or resulting from misuse, abuse, neglect or damage caused by accident or the failure to provide reasonable maintenance. This Warranty is void if the product or any of its individual components is altered or modified by the purchaser or if the product is used in a manner or with a blade not recommended by the manufacturer. Any claim arising under this Warranty must be submitted by the original purchaser within the warranty period specified above, and shall include proof of purchase. During said warranty period Barranca Diamond shall, at its option, either replace or repair, at no charge to the original purchaser, any parts or components that are found to be defective by Barranca Diamond. Barranca Diamond shall not be responsible for or obligated to pay for freight or other transportation related costs or expenses in connection with any defective products or components that are either returned to Barranca Diamond s facility or any authorized repair station and/or any replacement products or components that are shipped from Barranca Diamond pursuant to this Warranty. Parts and labor needed to maintain products and the replacement of components due to normal wear and tear are the purchaser s responsibility and are not covered by this Warranty. All products or components replaced under warranty become the property of the manufacturer. All replacement parts will be considered to be part of the original product and any warranty on such parts will expire coincidentally with the original Warranty. Barranca Diamond will pay for parts and labor in connection with warranty repairs conducted by Barranca Diamond or its authorized repair centers. Replacement part(s) installed by anyone else will be provided without a charge for such replacement part(s), but this Warranty will not apply to labor charges in connection therewith. IN NO EVENT SHALL ANY LIABILITY UNDER THIS WARRANTY EXCEED THE REPLACEMENT COST OF ANY DEFECTIVE PRODUCT OR COMPONENT THEREOF, AND BARRANCA DIAMOND SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR ANY OTHER DAMAGE OR LOSS NOT EXPRESSLY ASSUMED AS SET FORTH HEREIN. The foregoing constitutes an expressed warranty on the terms set forth above and is the only warranty or warranties applicable to the products it covers. All other warranties, including, without limitation, the implied warranty of merchantability and/or fitness for a particular purpose or use being denied. This limited warranty is expressly in lieu of all other warranties, whether expressed or implied. 3
HP-30 WARRANTY SPECIFICS APPLICABLE TO LIMITED WARRANTY OF DIAMOND BLADES AND CORE BITS Laser Welded Blade and Bit Warranty If the laser weld between the segment and the steel core or barrel fails during normal use, the blade or bit will be replaced free of charge. Blades and bits damaged due to careless or improper use are not covered under this warranty. Brazed Blade, Bit, and Cup Wheel Warranty If the brazed bond between the segment and the core, barrel, or cup fails within the first.00 of segment wear, the blade, bit, or cup will be replaced free of charge. Blades, bits, and cup wheels damaged due to careless or improper use are not covered under this warranty. Continuous Rim Blade Warranty If the bond between the rim and the core fails during normal use, the blade will be replaced free of charge. Blades and bits damaged due to careless or improper use are not covered under this warranty. Exclusions Barranca Diamond does not warrant the following components, which carry their own manufacturer s warranty for the indicated periods: Electric Motors Manufacturer s Warranty ABB Baldor: year Ryobi: Year Soga: Year Gas Engines Manufacturer s Warranty Honda: years Engine Power Information Engine power ratings are calculated by the individual engine manufacturer and the rating method may vary among engine manufacturers. Barranca Diamond Products makes no claim, representation or Warranty as to the power rating of the engine on this equipment and disclaims any responsibility or liability of any kind whatsoever with respect to the accuracy or the engine power rating. Users are advised to consult the engine manufacturer s owner's manual and website for specific information regarding the engine power rating. 33
HP-30 SERVICE & WARRANTY REPLACEMENT PARTS Replacement parts for this tool may be ordered form your Barranca Diamond distributor or directly from Barranca Diamond. Please have the following information ready before calling: Model and serial number of the machine Date of purchase Description of parts being ordered (see attached parts list) RETURN MATERIALS PROCEDURE To expedite the service relative to the return of a product purchased through Barranca Diamond, please have the following information available: Model and serial number of the machine Date of purchase Distributor s name Then please call Barranca Diamond at (30) 3-67 or toll free at 00-630-76 to obtain a Return Goods Authorization number (RGA) authorizing the return. Please Note: Ensure your item(s) are prepaid to the destination Return items must have been purchased within the previous twelve () months Follow the packaging instructions in the following section Be sure to include the RGA number, return address and your phone number on or within the return shipping box. PACKAGING INSTRUCTIONS Ship the saw using its plywood shipping crate. Use wood screws to fasten the baseboard to the /" plywood crate bottom so as to secure it inside the shipping crate. 3
NOTES 3
Barranca Diamond Products, Inc. 3 Storm Parkway Torrance, CA 900 Toll-Free: (00) -30 Phone: (30) 39- Fax: (30) 39- www.barrancadiamond.com