50 Ton Ram Specifications Dixon Valve & Coupling Company 800 High Street Chestertown, MD 0 ph: 800 355 99 fax: 800 83 49 www.dixonvalve.com
Item Part No. 50T003 50T04 00-0008 50T0 50T09 50T00 50T0 50T00 50T05 50T008 00-009 3-300 GLSS0000 00-004 50T00 50T007 50TDH9004 50TDH003 30-300 Description Qty. 3 4 5 7 8 9 0 3 4 5 7 8 9 Tie Rod Tie Rod Hex Nut Hydraulic Pump Hydraulic Pump Support Hydraulic Cylinder Cylinder End Plate Cylinder Backing Plate Cylinder Tie Rod Cylinder Tie Rod Nut Rod Cap Hydraulic Hose with Hydraulic Couplings Hydraulic Quick Connect NPT Plug 0-0,00 P.S.I. Liquid Filled Gauge Gauge Adapter 45 Die Bed Plate Die Retainer Strap 9" Die Carrier " Die Carrier Hydraulic coupling 3 4 8 Specifications
Specifications: Net Weight Crated Weight Dimensions Crated Dimension Pump Motor Motor Control Safety Valves Control Valve Gauge Reservoir Oil Delivery 30 lbs., basic equipment only 780 lbs. 53" long x 8" wide x 9" high 7" long x 40" wide x 48" high Power Team PE554 -/8 H.P. Universal Motor;,000 RPM; 5V single phase, 0/50 cycle AC (not dual voltage); 5 Amp, lightweight handle-top housing Run-Off-Remote motor control switch; 5 Amp motor control relay Cavity mounted in motor housing, hand held remote switch Relief valve set at 0,000 PSI Built-in manually operated 4-way control valves with 3/8" NPT port Calibrated 0-0,000 PSI Convenient mounting holes in base 50 cu. in/min. at 00 PSI 80 cu. in/min. at,000 PSI 70 cu. in/min. at 5,000 PSI 55 cu. in/min. at 0,000 PSI Note: -stage pump provides fast, no load approach speed and then shifts into slow actuation as the load is applied. Ram double acting (Power Team RD553-B) 3-/8" stroke 55 tons of push at 0,000 PSI 8 tons of pull at 0,000 PSI Preparations: Filling the Reservoir Approved Hydraulic Oils Before removing the filler plug, clean the area around the plug. The pump is a precision built unit, so special care should be taken to preclude foreign particles from entering the reservoir. With cylinder fully retracted, fill the tank " to ½" from the top. Replace the filler plug. Power Team 937 Mobil DTE5 or equivalent. Available Motor Variations Reservoir Variations 0-440, etc. Also ½ H.P. and 3 H.P. 5 gallon or 0 gallon reservoir available The standard -/8 H.P.,,000 RPM, 5 volt motor and the ½ gallon reservoir has proven highly successful. Dixon feels it is the best design, and variations are available, although not neccessarily desirable. Specifications
Operating Controls F-N-R (Forward-Neutral-Reverse) directional control lever. The F-N-R lever (shown in the neutral position) controls the direction of the ram cylinder. To extend the cylinder (forward) in the direction of the die bed, move the lever toward the pump motor then activate the pump. To retract the cylinder (reverse), move the lever away from the pump motor then activate the pump. On-Off-Remote switch, 0-0,000 psi pressure gauge and hand held remote. When the toggle switch is placed in the On position, the pump motor will run until the toggle switch is placed in the Off position. When the toggle switch is placed in the Remote position, the hand held remote is activated. To run the pump motor, depress and hold the switch on the remote. To stop the motor, release the switch on the remote. For practical purposes, leave the toggle switch in the Remote position. All future references to activating the pump motor should be understood that the hand held remote is being used. Caution! Never dead-end the cylinder (fully extended or fully retracted) and leave it with pressure showing on the gauge. If the cylinder is dead-ended, always move the lever to the neutral position after stopping the pump. Failure to do so can shorten the life of the cylinder seals. Specifications 3