INSTALL GUIDE DOCUMENT NUMBER 450 REVISION DATE FIRMWARE IDL-IDS(RS)-BZB-[ADS-BZ] HARDWARE ADS-BZ ESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DIRECTED SMART & ADS-HRN(RS)-SM0 (OPTIONAL) ADS-TOOLS-MB0 (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
PAGE OF 8 VEHICLE LIST - OF FEATURES SECURE TAKEOVER DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK PARKING LIGHT CTRL RAP SHUTDOWN CTRL TACHOMETER STATUS MONITORING BRAKE PEDAL STATUS MONITORING VSS STATUS MONITORING Sprinter Diesel STD key AT -09 Sprinter STD key AT -7 Sprinter Diesel STD key AT -7 Sprinter STD key AT 0-7 Sprinter Diesel STD key AT 0-7 INSTALL TYPE MAKE MERCEDES-BENZ FREIGHTLINER DODGE TRUNK STATUS MONITORING X LOCK /STANDALONE MOD. -09 DOOR STATUS MONITORING YEAR Sprinter STD key AT GLOW PLUG STATUS MONITORING MODEL NOTES I This firmware covers Automatic Transmission (AT) vehicles only.
PAGE OF 8 BOX CONTENTS - OF BOX CONTENTS MODULE LED LED PROGRAMMING BUTTON USB BLACK BLACK BLACK BLUE 4 6 5 4 6 8 0 4 6 8 0 5 7 9 5 7 9 4 6 5 BLACK EXPANSION PACK BLACK 4 RED BLUE 4 BLACK 4 BLUE TELEMATIC PORT PIN BLACK CONNECTOR AFTERMARKET HOOD SWITCH AND CABLE 9 0 7 8 5 6 4 WHITE 9 7 5 BLACK 0 8 6 4 H-HARNESS STICKER BLACK RF PORT/WEBLINK PORT XP LED STICKER EXPANSION PACK ASSEMBLY XP LED LED 4 LED TOP VIEW BLUE 0 PIN WHITE CONNECTOR T-HARNESS 4 5 7 9 5 7 9 4 6 8 0 4 6 8 0 BOTTOM VIEW TOP VIEW BLACK WEBLINK CABLE (required accessory sold separately) ELECTRONIC IGNITION SWITCH REMOVAL TOOL (accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT IGNITION SWITCH ADS-TOOLS-MB0 OR MERCEDEZ BENZ P/N 69 589 0 00 4 PIN BLACK CABLE
PAGE 4 OF 8 COMPATIBLE ESSORIES - OF RF KIT (accessories sold separately) RF KIT MODULE RF PORT ANTENNA TELEMATIC KIT (accessories sold separately) ADS-HRN(RS)-SM0 DIRECTED SMART (NC) MODULE TELEMATIC PORT (NC) (NC)
TECHNICAL NOTE - OF IMPORTANT PAGE 5 OF 8 INSTALL VIDEO GALLERY AVAILABLE ONLINE Before installing this product, consult our Install Video Gallery and watch: Vehicle Disassembly Procedure videos Module Connection Procedures videos Module Programming Procedures videos Æ To access the videos, simply log in your Weblink user account, and click on "Install videos" under the "Support" tab. Æ Then, select a vehicle make, year and model to display the available videos.
PAGE 6 OF 8 MODULE INSTALLATION PROCEDURE - OF 0 the vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle. Turn the vehicle. 0 WARNING: Any vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. An OEM scantool will be required to clear the error messages. If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP 4 of the WIRING DIAGRAM. the vehicle. Verify all vehicle functionalities. 4 If required, connect a compatible RF Kit to the RF port of the module. RF 0 Verify all keyfob functionalities (Door Lock, Door Unlock, Trunk Release and RFID access if equipped). 09 Insert the expansion pack in the module. 0 WARNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support. 5 If required, connect a compatible Telematics Device to the TELEMATIC port of the module. Turn the vehicle. 6 Put sticker on a clean and visible surface in the engine bay and put sticker under the dashboard near the OBDII connector. 7 Module installation procedure completed. Connect the module to the computer with the programming cable (WEBLINK port). Flash the module with the latest firmware then flash the expansion pack. Connect every connector to the module, as shown in STEP of the WIRING DIAGRAM. Connect and secure every connector to the vehicle, as shown in STEP of the WIRING DIAGRAM. Connect every other connector to the module, as shown in STEP of the WIRING DIAGRAM.
PAGE 7 OF 8 TYPE - WIRING DIAGRAM - OF WARNING STEP -TO CONNECT THE MODULE: FOLLOW STEPS TO 4 -TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO CONNECT TO VEHICLE VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS BLACK 5 PIN A (VEHICLE HARNESS) MODULE STEP IGNITION SWITCH CONNECT TO MODULE BLACK 5 PIN BLACK 0 PIN A RELAY STEP BLACK 8 PIN BLACK 8 PIN B CONNECT TO MODULE BLUE 6 PIN BLACK 8 PIN BLACK 8 PIN B (VEHICLE HARNESS) BLACK 0 PIN BLACK PIN (NOT USED) STEP 4 CONNECT IF REQUIRED WHITE 0 PIN IF NOT EQUIPPED WITH AN OEM HOOD SWITCH, INSTALL AN AFTERMARKET HOOD SWITCH HOOD SWITCH GRAY/WHITE - HOOD STATUS (-) INPUT GRAY/BLACK (NOT USED)
MODULE PROGRAMMING PROCEDURE - STD KEY - OF 0 LED is solid RED. Insert key into ignition. Module Programming Procedure completed. ON 0 PAGE 8 OF 8 Turn key to ON position. ON 0 Wait, LED will turn solid GREEN then will turn. ON vehicle for 5 seconds. LED will turn solid RED. Wait, LED will turn solid GREEN then will turn. Turn key to position. Remove key from ignition. ON
VALET MODE PROGRAMMING PROCEDURE - OF NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within 7 seconds. 0 PAGE 9 OF 8 To exit valet mode: repeat steps to 4 then vehicle for 5 seconds. Cycle ignition ON five times [5x /ON] rapidly. Parking Light will flash once [x]. 0 Wait, Parking Light will flash twice [x], pause for.5 second, then will flash once [x] to indicate that the valet mode is ON or twice [x] to indicate that the valet mode is. Turn ignition to position. Valet Mode Programming Procedure completed.
AFTERMARKET REMOTE PROGRAMMING PROCEDURE - OF WARNING: Program aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system. Parking Light will flash once [x]. 0 Time restriction. Complete next step within 7 seconds. To program additional remotes: repeat steps 4 to 6 using each additional remote. Cycle ignition ON five times [5x /ON] rapidly. Wait, Parking Light will flash twice [x]. Parking Light will flash once [x]. 0 PAGE 0 OF 8 0 Turn ignition to position. Time restriction. Complete next step within 5 seconds from previous step. 09 vehicle for 5 seconds. Press once [x] on LOCK button of aftermarket remote. 0 Aftermarket Remote Programming Procedure completed.
PAGE OF 8 MODULE NAVIGATION PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. Module must be programmed to the vehicle. Use the Module Navigation Chart on the next page. Set ignition to position. TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 TO ESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. 0 0 [X]
PAGE OF 8 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES I Default settings are listed in bold. 0 0 ON 0 0 ON 0 0 ON 0 0 ON 0 ENABLE 0 DISABLE* 0 45 SEC 0 90 SEC 0 0 MIN MIN 0 DISABLE 0 N/A 0 LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK 0 0 MIN 0 MIN 0 0 MIN 5 MIN 5 MIN 0 MIN 5 MIN 5 MIN 0 0 SEC 0 SEC 0 SEC 0 SEC 5 SEC 0 SEC 5 SEC 0 SEC 0-5 N/A 0 N/A 0 0 N/A 0 II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 0 [Z] SETTINGS MODULE NAVIGATION CHART - OF DISARM/UNLOCK BEFORE RELOCK AFTER RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS TAKEOVER SECURE TAKEOVER DELAY FACTORY KEYLESS RS SEQUENCE CONFIGURATION 09 0- Technical Support only MODULE RUN TIME WAIT TO DELAY N/A *Vehicle will shutdown when a door is opened.
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE ER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Engine running. 0 Key in ignition at ON position. II After a remote starter failure, the parking lights will flash three [x] times, then will flash [X] number times to indicate an error code. See table. 0 N/A Trunk is open. Foot brake is ON. Hood is open. N/A Tach failure. 09 N/A 0 System is in Valet Mode. CAN communication failure RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE ER ERROR CODES: NOTES I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Engine tach signal is lost. 0 N/A II If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for.5 seconds when using a -WAY remote. OR Press once [x] on button 4 when using a -WAY remote. 0 Foot brake is ON. Hood is open. Engine RPM limiter is ON. Glow plug timeout error. Vehicle is moving (VSS). Check engine warning light is ON. 09 Low fuel warning light is ON. 0 N/A CAN communication failure during RS sequence. REMOTE ER SHUTDOWN ERROR CODES: NOTES The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. PAGE OF 8
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE 4 OF 8
MODULE RESET PROCEDURE - OF 0 Disconnect all connectors from module except the BLACK 0-PIN connector. Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. Repeat programming procedure. 0 PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. Failure to follow procedure may result with a DTC or a CHECK error message. Wait, LED will flash RED. RELEASE programming button. LED will turn RED for seconds. Module RESET completed. PAGE 5 OF 8
TAKEOVER PROCEDURE - OF All vehicle doors must be closed and locked prior to remote start sequence. Press and release BRAKE pedal. 0 Time restriction. Complete steps to 6 within 45 seconds. Take over procedure completed. 0 Unlock driver door. Failure to follow procedure will result in vehicle engine shutdown. 0 Open driver door and enter vehicle. Close driver door. PAGE 6 OF 8 Push start button once [x] to ON position OR turn key to ON position.
INSTALLATION CHECKLIST - OF PAGE 7 OF 8 CHECKLIST 0 WARNING: Vehicle engine will start many times. Test in a well ventillated area. 0 Open driver door window for easy vehicle access. 0 Enter vehicle. Start the vehicle and let it run for 5 seconds. Stop the vehicle and exit vehicle. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. QUESTION : Does the vehicle remote start? YES: Go to step 7. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat step 6 and call technical support if the problem persists. QUESTION : Does the vehicle shut down? YES: Go to step 8. Open hood. NO: Repeat step 7. If the problem persists, unlock the door using the OEM keyfob, enter vehicle and press brake pedal to shut down the vehicle and call technical support. QUESTION : Is the orange warning sticker "Sticker " placed under the hood? YES: Leave hood open and go to step 9. 09 Close all doors. 0 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. NO: Put the mandatory orange warning sticker "Sticker ", leave hood open and go to step 9. QUESTION 4: Does the vehicle remote start? YES: Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Go to question 5. NO: Go to step. QUESTION 5: Is the vehicle equipped with a factory hood switch? (Inside hood latch) YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support. Close hood. Enter vehicle. Do NOT press brake pedal. Close all doors. 4 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. 5 Wait for the vehicle to start. 6 Press brake pedal. NO: Install the mandatory hood switch included in the kit. Repeat installation checklist. QUESTION 6: Does the vehicle shut down? YES: Go to step 7. NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle and call technical support.
INSTALLATION CHECKLIST - OF PAGE 8 OF 8 CHECKLIST 7 Exit vehicle. 8 Close all doors. 9 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. 0 Wait for the vehicle to start. Press UNLOCK button once [x] on the OEM keyfob. Within 45 seconds, go to step. Open driver door. QUESTION 7: Does the vehicle shut down? YES: The module does NOT detect the unlock signal from the vehicle communication network. Call technical support. Enter vehicle. 4 Insert key into ignition and turn key to ON position. 5 Press and release brake pedal. NO: Go to step. QUESTION 8: Does the vehicle shut down? YES: Repeat procedure from step. If the problem persists, call technical support. 6 Shut down the vehicle. 7 Installation checklist completed. NO: Go to step 6.