install guide Document number 655 Revision Date 098 firmware FLC-CH(RS)-CH4-[FLRSCH4] hardware FLRSCH4 accessories FLPROG (REQUIRED) FLRF//4 (OPTIAL) CARLINK ASCL (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. BEFORE INSTALLATI - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
Page of 0 VEHICLE LIST - OF PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX IGNITI CTRL RAP SHUTDOWN CTRL HOOD STATUS (W/OEM SW) DOOR STATUS BRAKE PEDAL STATUS TACHOMETER STATUS SECURE TAKEOVER PARKING LIGHT CTRL* 00c AT 08-0 00c SRT8 AT 08-0 Town & Country AT 08-4 Caravan AT 08-0 Challenger SXT AT 08-4 Challenger R/T AT 08-4 Challenger SRT8 AT 08-4 Charger SE AT 08-0 Charger R/T AT 08-0 Charger SRT8 AT 08-0 Durango AT - Grand Caravan AT 08-5 Journey AT 09-0 Magnum AT 08 Commander AT 08-0 Grand Cherokee AT 08- C/V AT 0-500 AT 0-500 AT 0-500 AT 0-4500 AT - 5500 AT - Routan AT 09- POWER SLIDING DOOR (R) X LOCK REMOTE 08-0 POWER SLIDING DOOR (L) DATA IMMOBILIZER BYPASS 08-0 00 Limited AT POWER LIFTGATE YEAR 00 AT INSTALL TYPE MODEL VW RAM JEEP DODGE CHRYSLER MAKE FEATURES * May require additional parts.
Page of 0 BOX CTENTS - OF BOX CTENTS MODULE LED BLUE BLACK BLACK 0 PIN CNECTOR T-HARNESS 4 6 5 4 6 8 0 4 6 8 0 5 7 9 5 7 9 4 6 8 0 5 7 9 PROGRAMMING BUTT LED A G F B E 4 BLACK RF PORT/ WEBLINK PORT 4 BLUE TELEMATIC PORT BLACK MS VS PIN CNECTOR VS MS AFTERMARKET HOOD SWITCH AND CABLE C D 9 0 7 8 5 6 4 WHITE WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE
Page 4 of 0 COMPATIBLE ESSORIES - OF RF KIT (accessories sold separately) FLRF//4 RF KIT (NC) MODULE RF PORT ANTENNA TELEMATIC KIT (accessories sold separately) CARLINK FLHRNTM MODULE TELEMATIC PORT (NC) TELEMATIC KIT (accessories sold separately) FLHRNTM PN 4060 MODULE TELEMATIC PORT 4 5 6 7 8 9 0 4 5 6 VEHICLE OBDII PORT (NC) OBDII CNECTOR CAR CNECTI
Page 5 of 0 CHRYSLER 00C 00 SRT8 Town & Country Town & Country Caravan Challenger R/T Challenger SXT Challenger SRT8 DODGE Charger SE Charger R/T Charger SRT8 Durango Grand Caravan Grand Caravan Journey Magnum 08-0 08-0 08-0 -4 08-0 08-4 08-4 08-4 08-0 08-0 08-0 - 08-0 -5 09-0 08 POSITI WIRE COLOR POLARITY MODULE LOCATI COMPENT LOCATOR 08-0 CNECTOR TYPE 00 Limited CNECTOR COLOR 08-0 D4 0 pin D4 0 pin CNECTOR NAME YEAR 00 WIRE DESCRIPTI MODEL MAKE TYPE - WIRE CHART - OF D4 0 pin D4 0 pin D4 0 pin D4 6 pin White/Green D4 0 pin D4 0 pin D4 0 pin D4 0 pin D4 0 pin D4 0 pin D4 0 pin D4 6 pin White/Green D4 0 pin D4 6 pin White/Green White/Violet (+) D4 0 pin
Page 6 of 0 4500 VW 5500 Routan 0- - - 09- COMPENT LOCATOR 500 0- MODULE LOCATI 500 0- POLARITY RAM 500 - WIRE COLOR C/V 0 POSITI C/V 08- CNECTOR TYPE Grand cherokee CNECTOR COLOR 08-0 CNECTOR NAME YEAR Commander WIRE DESCRIPTI MODEL JEEP MAKE TYPE - WIRE CHART - OF Pin # of relay #7 Power module in engine compartment Pin # of relay #7 Power module in engine compartment D4 0 pin 0 D4 6 pin 0 White/Green D4 0 pin 0 White D4 0 pin 0 White D4 0 pin 0 White D4 0 pin 0 White D4 0 pin 0 White D4 0 pin 0
Page 7 of 0 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITI SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT A VS IGNITI CNECTOR E C D A VS IGNITI HARNESS A 4 6 5 4 6 8 0 4 6 8 0 5 7 9 5 7 9 MS B A MS VEHICLE WHITE/GREEN (NC) WHITE/RED (NC) WHITE/BROWN - PARKING LIGHT OUTPUT PARKING LIGHT CNECTI CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT PARKING LIGHT OR C 4 6 5 8 7 0 9 CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT 0 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT 0 AMPS PARKING LIGHT V (+) OR GRAY/GREEN - HORN OUTPUT CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT (+) D 85 87 86 87A 0 4 6 8 0 5 7 9 PARKING LIGHT (+) GRAY/WHITE - HOOD STATUS INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CNECT TO AFTERMARKET HOOD SWITCH OPTIAL DRIVER DOOR PIN HORN AFTERMARKET HOOD SWITCH
MODULE PROGRAMMING PROCEDURE - STD KEY - OF 0 Close driver door. 07 Turn key to position. 0 Re-open driver door to wake up data bus. 08 Remove key. 0 Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. Turn key to position. 0 Wait, LED will turn solid GREEN for seconds. 05 LED will turn solid RED. Module Programming Procedure completed. 06 Within 5 seconds, LED will flash GREEN rapidly. Page 8 of 0
MODULE PROGRAMMING PROCEDURE - PTS - OF 0 Close driver door. 07 Press UNLOCK on the OEM remote. 0 Re-open driver door to wake up data bus. 08 Wait, LED will turn solid GREEN for seconds. DO NOT PRESS BRAKE PEDAL. Push start button twice [x] to position. 09 Module Programming Procedure completed. 0 STOP Page 9 of 0 ENGINE STOP LED will turn solid RED. 05 Within 5 seconds, LED will flash GREEN rapidly. 06 STOP DO NOT PRESS BRAKE PEDAL. Push start button once [x] to position. ENGINE STOP
VALET MODE PROGRAMMING PROCEDURE - OF 0 06 Insert key into ignition. 07 Valet Mode Programming Procedure completed. Time restriction. Complete next step within 7 seconds. To exit valet mode: repeat steps to 6. Remove key. 0 0 NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Page 0 of 0 Turn key to position then to position five times [5x] rapidly. 5x Wait, LED will turn solid RED for seconds. 05 Turn key to position.
aftermarket Remote PRogRamming - OF Page of 0 aftermarket Remote PRogRamming: notes I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.
Page of 0 MODULE NAVIGATI PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. Module must be programmed to the vehicle. 05 Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 0 0 [X] TO ESS THE OPTIS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATI. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously.
Page of 0 [Y] options [X] menus module navigation chart: notes I Default settings are listed in bold. 0 II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 DISARM/UNLOCK BEFORE RELOCK AFTER RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL FIRST PRESS 05 TAKEOVER 06 07 0 [Z] settings module navigation chart - OF FACTORY KEYLESS RS SEQUENCE CFIGURATI 08 09 MODULE RUN TIME WAIT TO DELAY 0 off 0 0 off 0 0 off 0 0 off 0 0 enable 0 DISABLE* 0 0 DISABLE 0 0 LOCK + UNLOCK + LOCK LocK + LocK + LocK 0 0 MIN 0 05 MIN 0 0 MIN 5 MIN 05 5 MIN 06 0 MIN 07 5 MIN 08 5 min 0 0 sec 0 05 SEC 0 08 SEC 0 SEC 05 5 SEC 06 0 SEC 07 5 SEC 08 0 SEC 0 0 0 0 0 *Vehicle will shutdown when a door is opened.
Page 4 of 0 [Y] options [X] menus module navigation chart: notes 4 0 [Z] settings module navigation chart - OF HORN EVENT TRIGGER CFIGURATI 5 0-07 Technical Support only 0 HORN CHIRPS WIDTH 0 DoubLe LocK 0 LOCK + UNLOCK 0 LOCK + UNLOCK + DOUBLE LOCK + 0 0 msec 0 5 msec 0 60 msec 0 *Vehicle will shutdown when a door is opened.
[X] number of PaRKing Light FLashes Diagnostic Remote starter error codes - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is. Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 0 4 5 6 CAN communication failure during RS sequence. Remote starter error codes: notes Page 5 of 0
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITI Diagnostic test module LeD status module Diagnostics - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. Page 6 of 0
MODULE RESET PROCEDURE - OF 0 Disconnect all connectors from module except the BLACK 0-PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK 0-PIN connector. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. 06 Module RESET completed. Page 7 of 0
TAKEOVER PROCEDURE - STD KEY - OF All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. Failure to follow procedure will result in vehicle engine shutdown. 0 Page 8 of 0 Turn key to position. Press and release BRAKE pedal. 05 Take over procedure completed.
TAKEOVER PROCEDURE - PTS - OF All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. 0 STOP Page 9 of 0 DO NOT PRESS BRAKE PEDAL. Push start button twice [x] to position. Wait seconds for key validation. ENGINE STOP 0 Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown.
installation checklist - OF Page 0 of 0 checklist WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question : Do the doors lock? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. RAP and auto light shutdown test YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 0 4 Press the UNLOCK button once [x] on the aftermarket keyfob. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question : Do the doors unlock? Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the trunk or hatch open/unlock? Question 9: Does the vehicle remote start? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. 5 Enter vehicle and close the doors. Question 4: Does the driver side sliding door open? 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. YES: Press the AUX button once [x] to close the driver sliding door and go to next step. 7 Wait for the vehicle to start. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press brake pedal. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. YES: Go to next step. 6 YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. Question 0: Does the vehicle shut down? Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 0 Installation checklist completed. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.