DDEC VI APPLICATION AND INSTALLATION APPENDIX C: PARAMETER LIST Gov TSC1 Condition 1 Gov TSC1 Condition 2 Gov TSC1 Condition 3 Gov TSC1 Condition 1 1 DI 1 21 DI 15DOFault 1 1 DI 1 15 DI 2 8 DI 2nd Axle Switch Config 3 1 AI 35AO 36AO 37DOFault 22 16 VEPS - Series 6; 16 - MBE 22 16 VEPS - Series 6; 16 - MBE 22 16 VEPS - Series 6; 16 - MBE 22 16 VEPS - Series 6; 16 - MBE 13 3 VEPS 13 2 1 VEPS =disable, 1=enable Dual Axle, 2=enable transmission retarder input, 3=FUSO Auxiliary brake cut switch =disable, 1=enable park brake interlock, 2=FUSO Park brake switch 13 2 VEPS 13 3 1 VEPS 13 2 1 VEPS 13 3 VEPS 13 3 VEPS 9 4 VEPS 9 3 VEPS =disable, 1=enable aux shutdown, 2=FUSO Accelerator switch =disable, 1=Shutdown override / Request (Fault Code Flashing), 2=CC-Cancel, 3= Request (Fault Code Flashing) =disable, 1=Remote-Throttle enable, 2=Service-Brace active =hardwired, 1=Ccvs1, 2=Ccvs2, 3=Ccvs3 =no sensor, 1=air filter restriction sensor, 2=OI Thermostat input, 3=FUSO Clutch pedal sensor input =disabled, 1=oil pressure lamp, 2=5 bar oil pressure gauge, 3=1 bar oil pressure gauge, 4=fuel filter sensor =disabled, 1=coolant temperature lamp, 2=coolant temperature gauge, 3=OI Thermostat input All information subject to change without notice. (Rev. 3/7) C-1
APPENDIX C: PARAMETER LIST 37DO 3 8 DO Fault 38DO 3 9 DO Fault 39DO 3 1 DO Fault 31DO 3 12 DO Fault 312DO 3 17 DO Fault 317DO 3 18 DI 35 5 VEPS =disabled, 1=decompression valve, 2=grid heater, 3=TOP2 lockout solenoid, 4=modulation output for Allison Transmission without J1939 Interface (Gear1), 5=PTO valve for AGS2 35 7 VEPS =disabled, 1=exhaust brake only, 2=exhaust and decompression brake via single valve, 3=port extension turbo brake, 4=PTO stationary for AGS2, 5=PTO mobile for AGS2, 6=TOP2 shift solenoid, 7=Fuso starter lockout relay 35 5 VEPS =disabled, 1=grid heater hardwired, 2=AGS2 backup lamp, 3=engine brake active, 4=not used, 5=FUSO engine brake active lamp 35 5 VEPS =disabled, 1=air filter lamp, 2=AGS2 transmiss. temp indication lamp, 3=battery voltage low lamp, 4=coolant level low lamp, 5=Fuso retarder control 1 35 5 VEPS =disabled, 1=oil level lamp, 2=AGS2 check transmiss. indication lamp OI: Optimized Idle, 3=oil pressure lowlamp, 4=cruise / Pressure Governor System active lamp, 5=Fuso retarder control 2 35 7 VEPS 13 1 VEPS =disabled, 1=enable starter lockout, 2=enable kick down output, 3=not used, 4=optimized idle alarm, 5=split valve 2, 6=starter lockout and AGS2 run signal / starter lockout, 7=engine brake disabled for over speed =disable, 1=enable ABS input, 2=enable transmission retarder input, 3=enable tempo set, 4=enable grid heater detection, 5=switchable torque demand, 6=drive on super structure, 7=throttle inhibit super structure, 8=split select, 9=FUSO Engine brake stage 2 cancel switch, 1=DPF inhibit switch C-2 All information subject to change without notice. (Rev. 3/7)
DDEC VI APPLICATION AND INSTALLATION 46DOFault 46DO 47DOFault 47DO 4 8 DI 49DOFault 49DO 41DOFault 41DO 412PWM Output 35 3 1 VEPS =disabled, 1=grid heater lamp, 2=accelerator pedal idle position, 3=run signal / starter lockout 35 13 13 VEPS 13 2 1 VEPS =disabled, 1=accelerator pedal kick down, 2=actual torque, 3=road speed, 4=engine speed, 5=coolant temperature, 6=pedal torque, 7=boost temperature, 8=oil pressure (PLD threshold), 9=coolant temperature (PLD threshold), 1=vehicle power shutdown / ignition relay, 11=optimized idle ACC bus (ignition relay), 12=split valve 1, 13=High Exhaust Temperature Lamp =disable, 1=clutch switch, 2=PTO request for AGS2 35 12 VEPS =disabled, 1=accelerator pedal idle position, 2=actual torque, 3=road speed, 4=engine speed, 5=coolant temperature, 6=pedal torque, 7=boost temperature, 8=oil pressure (PLD threshold), 9=coolant temperature (PLD threshold), 1=optimized idle active lamp, 11=deceleration lamp, 12=Fuso ground starter lockout relay 35 3 VEPS 9 1 VEPS =disabled, 1=not used, 2=not used, 3=vehicle power shutdown / ignition relay =disabled, 1=throttle torque 1%..9%, 2=difference torque, 3=throttle torque 9%..1%, 4=actual torque, 5=load torque (no idle torque for automatic transmission), 6=road speed, 7=demand speed, 8=demand speed CC+, 9=AGS2 transmiss. temp indication lamp, 1=FUSO Accelerator PWM output All information subject to change without notice. (Rev. 3/7) C-3
APPENDIX C: PARAMETER LIST 4 13 DI 4 17 DI 4 18 DI AC Fan Vehicle AC Fan Vehicle Thresh Adaptive Cruise Control Adaptive Cruise Mask Adjusted Idle Configuration Air Condition Auto Fan AL Conditions AL Min Engine Torque AL Ramp up Rate 13 1 VEPS 13 3 2 VEPS 13 6 VEPS =disable, 1=enable ABS input, 2=enable transmission retarder input, 3=enable tempo set, 4=enable grid heater detection, 5=switchable torque demand, 6=drive on super structure, 7=throttle inhibit super structure, 8=split select, 9=FUSO Engine brake stage 2 cancel switch, 1=DPF inhibit switch =disable, 1=2 Clutch Switch, 2=DPF regeneration switch, 3=FUSO Air suspension speed limit switch =disable, 1=enable engine door bus, 2=enable engine hood, 3=AGS2 PTO Feedback, 4=RPM Freeze, 5=Engine Brake Disable, 6=Fast Engine Heat Up Switch 19 1 VEPS =disable, 1=enable 19 25 32.1875 VEPS 43 1 VEPS =disable, 1=enable 1 81 64 VEPS 3 4 VEPS 19 1 1 23 4 VEPS =no engine brake activation, 16=exhaust flap only, 17=Jake Brake 2nd stage, 64=decompression valve only or Jake Brake 1st stage, 8=decompression valve and exhaust flap, 81=decompression valveandturbo brake or Jake Brake 3rd stage =disabled, 1=enabled, 2=enabled if neutral, 3=enabled if neutral and park brake, 4=enabled if park brake =disable, 1=enable =AL permanently active, 1=No AL during shift, 2=extended AL with torque curve#3 thresh., 3=combination 1+2, 4=No AL during shift torque freeze + release 23 1% 1% VEPS 23 8191.875 ()/s VEPS..65535=signal C-4 All information subject to change without notice. (Rev. 3/7)
DDEC VI APPLICATION AND INSTALLATION Ambient Air Temp Sensor 31 4 VEPS Anti Tamper 8 2 Axle Ratio 8 1 2 5.29 Cab PTO Switch Config CC ON OFF Switch Config CC Pause Switch Config CC Set Cst Res Accel Sw Config CC1 Source Address SAE J1939 CC2 Source Address SAE J1939 CC3 Source Address SAE J1939 Clutch Switch Config CM1 DPF Source Addr SAE J1939 CM1 Fan Source Addr1 SAE J1939 CM1 Fan Source Addr2 SAE J1939 Config PTO Control 13 6 VEPS =not available, 1=hardwired, 2=reserved for J1939, 3=J1587, 4=ECAN =disabled, 1=enable anti-tampering function via ABS, 2=enable anti-tampering function via Gear Ratio =hardwired, 1=Ccvs1, 2=Ccvs2, 3=Ccvs3, 4=Ccvs1 or hardwired, 5=Ccvs2 or hardwired, 6=Ccvs3 or hardwired 13 3 VEPS CC ON OFF Switch Config 13 7 VEPS 13 3 VEPS =disabled, 1=Ccvs1, 2=Ccvs2, 3=Ccvs3, 4=Ccvs1 or Ccvs2, 5=Ccvs2 or Ccvs3, 6=Ccvs1 or Ccvs3, 7=Ccvs1 or Ccvs2 or Ccvs3 =hardwired, 1=Ccvs1, 2=Ccvs2, 3=Ccvs3 1 255 23 VEPS 1 255 33 VEPS 1 255 49 VEPS 13 6 9 VEPS =no clutch switch, 1=1 Clutch Switch, 2=2 Clutch Switch, 3=Ccvs1, 4=Ccvs2, 5=Ccvs3, 6=ETC1 1 255 49 VEPS 1 255 25 VEPS 1 255 49 VEPS 7 5 d, 2=enabled if neutral, 3=enabled if neutral and park brake, 4=enabled if park brake, 5=PTO while driving All information subject to change without notice. (Rev. 3/7) C-5
APPENDIX C: PARAMETER LIST Cool Level Eng Protect Shtdn Cool Level Sensor Input Coolant Temp Eng Protect Shtdn Cruise Control Eng Brk 18 1 1 32 4 2 VEPS 18 1 1 1 1 Cruise Power 15 2 Cruise RSL Eng Brk Mode Select Decrement Cruise Set DPF J1939 Inhibit Sw DPF J1939 Regen Sw DPF Lamp Config DPF Stationary Regen Only EBC1 Source Address SAE J1939 Cruise Auto Resume Idle PTO Shtdn Override 1 1 15 1 1.61 =warning, 1=engine shutdown =disable, 1=dual level probe sensor (IMO), fix threshold evaluation, 2=single level probe sensor (Rusty Nail), temperature dependent evaluation, 3=dual level float sensor (FTL), fix threshold evaluation, 4=single level probe sensor (Rusty Nail), fix threshold evaluation =disable, 1=enable =disable, 1=enable automatic engine brake operation with cruise control =high power only, 1=low power only, 2=Cruise power enabled =vehicle overspeed based, 1=torque interface based 46 1 VEPS =not active, 1=active 46 1 VEPS =not active, 1=active 46 1 VEPS =hardwired, 1=J1939 PTC1 46 1 1 VEPS =disabled, 1=enabled 1 255 33 VEPS 15 2 17 2 1 =disable, 1=enable automatic cruise resume function after clutch has been released once, 2=release clutch twice =disabled, 1=enabled, allows Stop Engine Override / Request switch (pin 1/15) to override engine idle/pto shutdown, 2=enable without clutch and service brake C-6 All information subject to change without notice. (Rev. 3/7)
DDEC VI APPLICATION AND INSTALLATION Idle Shutdown Noise Control PTO Shutdown Eng Brake Auto Fan Eng Brk Stage 1 Off Delay Time Eng Brk Stage 2 Off Delay Time Eng Brk Stage 3 Off Delay Time Eng Limit While Veh Stop Configuration Switch Config Engine Hour Sync Fault Fan AC Hold Time Fan Vehicle Fan Vehicle Threshold Fast Idle Spd Air Cond Input 17 3 =disable, 1=enable idle shutdown with Park Brake status, 2=enable idle shutdown without Park Brake status, 3=enable idle shutdown with edge triggered accelerator pedal 23 1 1 VEPS =VCU style, 1=DDEC style 17 3 19 1 =disable, 1=enable PTO shutdown with Park Brake status, 2=enable PTO shutdown without Park Brake status, 3=enable PTO shutdown with edge triggered accelerator pedal =disable, 1=enable 1 128 24 ms VEPS..64=signal 1 128 24 ms VEPS..64=signal 1 128 24 ms VEPS..64=signal 3 4 3 1 3 VEPS 13 255 VEPS =no engine brake, 1=Decompression Valve Only or Exhaust Flap Only, 2=decompression valve + exhaust flap, 3=jake compression brake or turbo brake =hardwired, 1=info from J1939 (muxed), 255=not available 37 1 1 VEPS =disabled, 1=enabled 19 s 6 s 18 s VEPS 19 1 VEPS =disable, 1=enable 19 25 VEPS..32=signal 6 5 3 6 All information subject to change without notice. (Rev. 3/7) C-7
APPENDIX C: PARAMETER LIST Fault Code Flashing FEI Conversion Factor FEI Max Vehicle Reward FEI Minimum Fuel Economy FEI Use Trip Mileage Fleet Management FM Alert Update FM Daily Usage FM Fuel Density FM Incident Update FM Monthly Trip FM Serv Interval Update Fuel Economy Incentive Gear Ratio for High Gear Power Gear Ratio Gear Down Protect 37 1 1 VEPS =disabled, 1=enabled 23 mph /mpg 23 23 4 mpg 2 mph /mpg 2 2 mpg 2mph /mpg 7mpg 23 1 27 1 1 27 1 1 27 1 1 27 kg/l 65.535 kg/l.835 kg/l 27 1 1 27 1 1 27 1 1 23 1 =based on filtered fuel economy, 1=based on trip fuel economy =disabled, 1=enabled =disabled, 1=enabled =disabled, 1=enabled VEPS =disabled, 1=enabled =disabled, 1=enabled =disabled, 1=enabled =disabled, 1=enabled 23 2.2 VEPS 23 2.1 VEPS C-8 All information subject to change without notice. (Rev. 3/7)
DDEC VI APPLICATION AND INSTALLATION Hi Amb Air Override Temp Hi Eng Brk Max Cruise RSL Spd Hi Eng Brk Min Cruise RSL Spd Hi Exhaust Temp Lamp Config Hold Time Fan Idle Shutdown Auto Override Idle Shutdown Time Increment Cruise Set J1587 Page2 SID Convert J1939 Engine Retarder Config J1939 Fan Request J1939 Steps Limiter Max Eng d Limiter Max Eng Trq d Limiter Max Road Spd d 17 4 C 75 C 32 C 1 1 48 48 1 6 46 1 VEPS =hardwired, 1=J1939 PTC1 19 s 6 s 1 s 17 1 17 1 s 15 5 s 1 6 s 1.6 =no automatic override performed, 1=automatic override performed 37 1 VEPS =disabled, 1=enabled 1 3 255 255 VEPS =variable controlled brake, 1=1 step, 2=low/high steps, 3=Jake or Constant Throttle Brake, 4= Exhaust Flap, 255=not configured 19 1 VEPS =disabled, 1=enabled 1 255 255 VEPS 5 5 Nm 5 4 5 Nm 152 4 5 Nm 152 =variable controlled brake, 1=1 step, 2=low/high steps, 3=low/medium/high steps, 255=not configured All information subject to change without notice. (Rev. 3/7) C-9
APPENDIX C: PARAMETER LIST Limiter Max Trq Curve Select Limiter Max Vehicle Accel Limiter Min Eng d Limiter1 Max Eng d Limiter1 Max Eng Trq d Limiter1 Max Road Spd d Limiter1 Max Vehicle Accel Limiter1 Min Eng d Lo Amb Air Override Temp Low Eng Brk Max Cruise RSL Spd Low Eng Brk Min Cruise RSL Spd Max Adjusted Idle Max Cruise Set Max Engine Load PTO Shutdown Max Engine Max PTO Spd Resume Accel Sw 4 3 VEPS 5 5 5 15.625 m/ss 5 5 5 5 15.625 m/ss 15.625 m/ss 4 4 5 Nm 152 15.625 m/ss 4 1 m/ss 5 4 5 Nm 152 1 m/ss 5 17 4 C 75 C 4 C 1 1 3 15 48 17 Nm 3 7 5 48 48 4 152 5 Nm 4 3 5 2 85 152 =PLD torque curve (max. torque), 1=Power Rating Curve #1, 2=Power Rating Curve #2, 3=Power Rating Curve #3 1 Nm VEPS 3 3 VEPS C-1 All information subject to change without notice. (Rev. 3/7)
DDEC VI APPLICATION AND INSTALLATION Max Road Max Road in PTO Mode Med Eng Brk Max Cruise RSL Spd Med Eng Brk Min Cruise RSL Spd MID for Ambient Air Temp Min Coolant Temp Min Cruise Set Min Eng Spd for Engine Brakes Min Engine Min PTO Spd Set Coast Sw Min Road Spd Eng Brk Operation Mode of AC Status Input No of s via Remote PTO Noise Max Engine Noise Min Engine Number of Output Shaft Teeth 3 12 6 1 1 31 152 128 48 48 255 152 1 VEPS 7 5 VEPS 17 4 C 2 C 1 C VEPS 15 1 3 7 16 5 1 152 4 4 3 2 32 11 592 5 VEPS VEPS 5 4 2 VEPS 7 1 3 1 23 23 4 4 145 11 8 25 16 =disabled, 1=AC active closed, 2=AC active open, 3=LIM active closed, 4=LIM active open VEPS VEPS All information subject to change without notice. (Rev. 3/7) C-11
APPENDIX C: PARAMETER LIST OI Alternate Battery Run Time OI Continuous Batt Time OI Extended Mode Disable OI Lower Limit Continuous Run OI Target Engine RPM ae OI Target Engine RPM ae 1 OI Target Engine RPM ae 2 OI Target Engine RPM ae 3 OI Target Engine RPM ae 4 OI Thermostat Max Time OI Upper Limit Continuous Run OI Variable Volt Thresh Oil Level Eng Protect Shtdn Oil Press Eng Protect Shtdn Optimized Idle 12 s 36 s s 12 1 12 1 12 4 C 1 C 4 C 12 12 12 12 12 8 8 8 8 8 12 s 1 1 1 1 1 459 s 1 1 1 1 1 s 12 4 C 1 C 32 C 12 1 18 1 1 18 1 1 =disabled, 1=enabled =enable, 1=disable =disabled, 1=enabled =warning, 1=engine shutdown =disable, 1=enable 12 1 VEPS =disable, 1=enable C-12 All information subject to change without notice. (Rev. 3/7)
DDEC VI APPLICATION AND INSTALLATION Park Brake Switch Config PasSmart Progressive Shift PS High Gear On Vehicle Spd PS High Gear RPM Limit PS Low Gear 1MaxRPM Limit PS Low Gear 1MaxVehicle Spd PS Low Gear 1RPMLimit PS Low Gear 2MaxRPM Limit PS Low Gear 2MaxVehicle Spd PS Low Gear 2RPMLimit PS Pass Duration PS Pass Increment PS Pass Interval PTO Dropout on Clutch d 13 3 VEPS 23 1 23 1 23 23 23 23 23 23 23 23 23 min 23 25 4 4 25 4 4 25 4 255 min 25 8.5 165 18 19.3 14 18 43.5 18 min 23 1 h 24 h 8 h 7 1 =hardwired, 1=Ccvs1, 2=Ccvs2, 3=Ccvs3 =disable, 1=enable =disable, 1=enable =No PTO drop out with clutch pedal, 1=Causes PTO to drop out if the Clutch is being depressed All information subject to change without notice. (Rev. 3/7) C-13
APPENDIX C: PARAMETER LIST PTO Dropout Serv Brk Prk Brk PTO Auto Fan Activation PTO Ramp Rate PTO Shutdown Time PTO Throttle Override 7 3 19 1 7 25 () /s 17 1 s Ramp Fan 19 1%/s Ramp Rate Adjusted Idle Spd Remote Accelerator Remote PTO Spd Mode Resume Accel Max PTO Torque Resume Accel Sw PTO Set Spd Road Spd Limit Max Stage Num Second Highest Gear Ratio Service Brake Switch Config 25 () /s 5 s 2 ()/s 6 s 7 1 1 3 () /s 1 %/s 8191.875 () /s =No PTO drop out on service brake or park brake activation, 1=Causes PTO to drop out on Service Brake or Park Brake activation, 2=Drop out on Service Brake activation, 3=Drop out on Park Brake activation =disable, 1=enable =disable, 1= engine speed in PTO mode to be increased with throttle input 25 %/s VEPS 1 ()/s 2 1 VEPS =disable, 1=enable 6 2 VEPS 7 Nm 7 5 Nm 3 5 Nm 5 =1 pulsed input(vcu style), 1=2 gray coded inputs, 2=2 binary coded inputs 1 3 VEPS =off, 1=low, 2=medium, 3=high 8 5.75 2.55 13 3 3 VEPS =hardwired, 1=Ccvs1, 2=Ccvs2, 3=Ccvs3 C-14 All information subject to change without notice. (Rev. 3/7)
DDEC VI APPLICATION AND INSTALLATION Service Brk Eng Brakes Set Coast Max PTO Torque Set Coast Switch PTO Set Single Step Adjusted Idle Spd Spd1Max Eng Trq Remote PTO Spd 1 via Remote PTO Spd2Max Eng Trq Remote PTO Spd 2 via Remote PTO Spd3Max Eng Trq Remote PTO Spd 3 via Remote PTO Stage 1 Eng Brk Off Delta Spd Stage 1 Factor Stage 1 Mask Stage 2 Eng Brk Off Delta Spd 1 2 7 Nm 7 3 7 Nm 7 5 7 Nm 7 5 7 Nm 7 1 5 5 Nm 3 1 5 Nm 3 5 Nm 3 5 Nm 3 8 5 Nm 5 16 5 Nm 95 5 Nm 125 5 Nm 185 1 =disable, 1=enable automatic engine brake when applied service brake, 2=operator selection and service brake for engine brake activation VEPS 1 % 1% 1% VEPS 1 81 64 VEPS 1 8 1 =no engine brake activation, 16=exhaust flap only, 17=Jake Brake 2nd stage, 64=decompression valve only or Jake Brake 1st stage, 8=decompression valve and exhaust flap, 81=decompression valve and turbo brakeorjakebrake3rdstage VEPS All information subject to change without notice. (Rev. 3/7) C-15
APPENDIX C: PARAMETER LIST Stage 2 Factor Stage2Mask Stage 3 Eng Brk Off Delta Spd Stage 3 Factor Stage3Mask Throttle Override Max Eng Spd Tire Revs per Unit Distance Top Gear Ratio Top2 Cruise Control Sw Torque Factor Gear Dwn Protect Torque Factor High Gear Power Trans Factor Trans Mask 1 % 1% 1% VEPS 1 81 8 VEPS 1 8 =no engine brake activation, 16=exhaust flap only, 17=Jake Brake 2nd stage, 64=decompression valve only or Jake Brake 1st stage, 8=decompression valve and exhaust flap, 81=decompression valve and turbo brake or Jake Brake 3rd stage 5 VEPS 1 1% 1% VEPS 1 81 8 VEPS 7 8 8 16 1/km.99 69375 3 1599 1/km 2.5498 46875 3 312 1/km 42 1 1 =no engine brake activation, 16=exhaust flap only, 17=Jake Brake 2nd stage, 64=decompression valve only or Jake Brake 1st stage, 8=decompression valve and exhaust flap, 81=decompression valve and turbo brake or Jake Brake 3rd stage =disable, 1=using cruise control master switch 23 1 VEPS 23 1 VEPS 1 % 1% 1% VEPS 1 81 64 VEPS =no engine brake activation, 16=exhaust flap only, 17=Jake Brake 2nd stage, 64=decompression valve only or Jake Brake 1st stage, 8=decompression valve and exhaust flap, 81=decompression valve and turbo brake or Jake Brake 3rd stage C-16 All information subject to change without notice. (Rev. 3/7)
DDEC VI APPLICATION AND INSTALLATION Trans Neutral Input Config 13 255 VEPS =hardwired, 1=info from J1939 (muxed), 255=not available Trans Retarder Fan Percent Trans Torque Limit Transmission Type Transmit EBC1 for AGS2 TSC1 Source Address SAE J1939 19 % 1% VEPS 3 1 VEPS =disabled, 1=enable 2 7 VEPS 1 3 VEPS Manual, without neutral switch, 1 NotUsedinNAFTA,2 Allison,Eaton UltraShift, AutoShift, ZF ASTronic: direct start, 3 Manual, with neutral switch, 4 Not Used in NAFTA, 5 Eaton AutoShift, UltraShift, ZF ASTronic,AGS2: MCMStart,6 Allison, Eaton UltraShift ASW: MCM Start, 7 Eaton Top2 =no EBC1, standard PTO message, 1=transmit EBC1 and standard PTO message, 2=no EBC1, AGS2 specific PTO message, 3=transmit EBC1 and AGS2 specific PTOmessage 1 255 231 VEPS Two Spd Axle Second Axle Ratio 8 1 2 5.29 Vehicle Sensor 8 8 4 =no sensor, 1=C3 sensor, 2=square wave (hall sensor), 3=J1939 ETC1, 4=magnetic pickup vehicle speed sensor, 5=J1939 TCO, 6=J1939 CCVS Source1, 7=J1939 CCVS Source2, 8=J1939 CCVS Source3 Table C-1 DDEC VI s All information subject to change without notice. (Rev. 3/7) C-17
APPENDIX C: PARAMETER LIST C-18 All information subject to change without notice. (Rev. 3/7)