E11 BOTTOM HUNG OPEN IN WINDOWS RC2 01.06.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com
CONTENTS 1. General characteristics...03 2. Size range...05 2.1. With vertically fitted handle.05 2.2. With hizontally fitted handle.05 3. Tilt windows with vertically fitted handle...07 3.1. Base set n 46811-2 and 46813-2 (with hook-in keeps) f frame groove 14/18 mm.07 3.2. Base set n 46831-2 and 46833-2 (with hook-in keeps) f frame groove 10/14 mm.08 3.3. Centre locking sets.09 3.4. Selection of rods.11 3.5. Keep and link arm positions.13 3.6. Installation instruction.16 4. Tilt windows with hizontally fitted handle...19 4.1. Base set n 20810-2 (with hook-in keeps) f frame groove 14/18 mm.19 4.2. Base set n 20830-2 (with hook-in keeps) f frame groove 10/14 mm.20 4.3. Centre locking sets.21 4.4. Selection of rods.22 4.5. Keep and link arm positions.24 4.6. Installation instructions.26 5. Order tables....29 5.1. Chrono Safe.29 5.2. Chrono Invision Pro Safe.31 5.3. Chrono Invision Go Safe.33 6. General infmation and glass tables...35.02
1. General characteristics General To make your windows extra secure against burglary, you should use the high security system Chrono Safe. The totally clampable Chrono Safe tilt system is available with visible hinges and with concealed hinges. All parts are made of high quality non-croding materials. Profile dimensions The Chrono Safe hardware is available to suit a frame groove of 14/18 mm a frame groove of 10/14 mm. Chrono Invision Pro Chrono Invision Go Frame groove 14/18 mm Frame groove 10/14 mm A 14 ± 0.5 10 ± 0.5 B 18 ± 0.5 14 ± 0.5 High security parts The set contains the following high security parts: 2, 3 5 stainless steel mushroom head bolts, pre-riveted to a connection piece in zinc alloy, the cner transmission and/ the bolts which are connected to the Chrono Safe components and rods in the vent section. 2 brass afterwards mounted security keeps which are fixed on the frame section with clamping plates in stainless steel and self-drilling screws. 1, 2 3 additional zinc alloy security keeps which are fixed on the frame section with self-drilling screws: Fh = 1800-2400 mm (only with vertically fitted handle) and/ Fb = 1200-1700 mm (with vertically fitted handle) Fb = 1800-2400 mm (with hizontally fitted handle) A zinc alloy anti-lift piece and protection piece which are fixed on the frame section with a clamping plate in stainless steel and self-drilling screws. A special zinc alloy connection piece at the handle position at the lockcase f operation with square spindle. 2 3 anti-lift pins in aluminium at the hinge side. Rods in synthetic material with increased tensile strength with special connections..03
Connection rods in synthetic material The system consists of 11 rods with different lengths, made of a solid, non-absbing, fibre-reinfced synthetic material, which offers the following advantages: quick assembly by the special toothed connections. no rattling. no me time-consuming rod operations. inaccuracies while sawing and punching are eliminated. adjustment range of each rod is 50 mm. inaccuracies while manufacturing the window can be overcome by the connection rods, which allow a maximum err margin of 8 mm in height (Fh) and 4 mm in width (Fb). The rods in synthetic material incpate locking points as standard which serve as an additional centre locking point f wider and higher windows. RC2 The Chrono Safe RC2 fittings are based on the Chrono Safe SKG** system, with the difference that additional high security keeps are mounted f windows with: Fh = 1800-2400 mm (only with vertically fitted handle) and/ Fb = 1200-1700 mm (with vertically fitted handle) Fb = 1800-2400 mm (with hizontally fitted handle) The fittings itself have no certificate, but are RC2 wthy, based on a reference test which has been carried out on an existing profile system. To obtain RC2 on other profiles, confmity of the fittings must be requested on the particular profile system. Chrono Safe RC2 is only available with post-assembly mounted security keeps. The keeps can be mounted after assembly of the frame. The clamping plate is already fixed to the keep by means of M5 screws. Special profiles!! F windows with concealed vent f steel look profiles, special fixing screws must be provided f the Chrono Safe keeps. Two flowdrill screws are provided, this only f the Chrono Safe keeps of the base set. F tilt windows there will be 4 screws per window. The 2 most extreme screws of the keep are replaced by the special screws. Order codes: Order code Description 30340-840-5 Screw set 20 pieces G30340-840-5 Screw set 200 pieces Miscellaneous The high security set should always be operated by a cylinder locking handle, available in different variations (see chapter E11.15). Milling vent groove:.04
2. Size range 2.1. With vertically fitted handle Chrono Safe Size range with connection piece: Vent width: 650-1800 mm. Vent height: 600-2400 mm. Vent weight: max. 90 kg. Chrono Invision Pro Safe Size range with connection piece: Vent width: 650-1800 mm. Vent height: 600-2400 mm. Vent weight: max. 130 kg. Chrono Invision Go Safe Size range with connection piece: Vent width: 650-1800 mm. Vent height: 600-1800 mm. Vent weight: max. 90 kg. Size range with lockcase: Vent width: 650-1800 mm. Vent height: 685-2400 mm. Size range with lockcase: Vent width: 650-1800 mm. Vent height: 685-2400 mm. Size range with lockcase: Vent width: 650-1800 mm. Vent height: 685-1800 mm. 2.2. With hizontally fitted handle Chrono Safe Size range with connection piece: Size range with lockcase: Vent width: 600-1200 mm. Vent width: 685-1284 mm. Vent height: 420-1200 mm. Vent height: 420-1200 mm. Vent weight: max. 40 kg. Vent weight: max. 40 kg. Size range with connection piece: Vent width: 1201-2400 mm. Vent height: 400-1200 mm. Vent weight: max. 90 kg. Chrono Invision Pro Safe Size range with connection piece: Vent width: 600-1200 mm. Vent height: 540-1200 mm. Vent weight: max. 40 kg. Size range with connection piece: Vent width: 1201-1800 mm. Vent height: 400-1200 mm. Vent weight: max. 130 kg. Size range with lockcase: Vent width: 1285-2400 mm. Vent height: 400-1200 mm. Vent weight: max. 90 kg. Size range with lockcase: Vent width: 685-1284 mm. Vent height: 540-1200 mm. Vent weight: max. 40 kg. Size range with lockcase: Vent width: 1285-1800 mm. Vent height: 400-1200 mm. Vent weight: max. 130 kg..05
Chrono Invision Go Safe Size range with connection piece: Vent width: 600-1200 mm. Vent height: 570-1200 mm. Vent weight: max. 40 kg. Size range with connection piece: Vent width: 1201-1800 mm. Vent height: 400-1200 mm. Vent weight: max. 90 kg. Size range with lockcase: Vent width: 685-1284 mm. Vent height: 570-1200 mm. Vent weight: max. 40 kg. Size range with lockcase: Vent width: 1285-1800 mm. Vent height: 400-1200 mm. Vent weight: max. 90 kg. Notes Handle height (vertically fitted): A = min. Fh/3, max. 2Fh/3. Vent width Fb x vent height Fh = max. 2.7 m². Adjustment range of each rod: 50 mm. Dimensions out of standard range on request! The Chrono system has been tested in accdance with following standards: European standard EN 1026, EN 1027, EN 12207, EN 12208, EN 12210 and EN 12211 f windows 50 m me above the ground..06
3. Tilt windows with vertically fitted handle 3.1. Base set n 46811-2 and 46813-2 (with hook-in keeps) f frame groove 14/18 mm 45140-550 45140-551 Chrono: Chrono Invision Pro: Chrono Invision Go Vent width Fb = 650-1200 mm Vent height Fh = 600-1200 mm (connection piece) Vent height Fh = 685-1200 mm (lockcase) Base set n 46811-2 and 46813-2 n 46811-2 n 46813-2 1 20300-620 20300-620 bolt 2 23300-771 23300-771 anti-lift pin 1 30000-530 30000-530 clips 1 30000-600 30000-600 vent run on rest 1 30340-630-1L 30340-630-1L protection piece left 1 30340-630-1R 30340-630-1R protection piece right 2 30310-841-1 30310-841-1 keep 1 41300-500 41300-500 cner transmission 1 45000-550-2 45000-551-2 vent part link arm 1 45140-550-1 45140-550-1 frame part link arm 10 St4.2x16Din7504P St4.2x16Din7504P drilling screw 5 St4.2x25Din7504P St4.2x25Din7504P drilling screw 4 St4.8x32Din7504P St4.8x32Din7504P drilling screw Hinge sets: see chapter E11.14. Connection piece set lockcase: see chapter E11.15..07
3.2. Base set n 46831-2 and 46833-2 (with hook-in keeps) f frame groove 10/14 mm 45140-550 45140-551 Chrono: Chrono Invision Pro: Chrono Invision Go: Vent width Fb = 650-1200 mm Vent height Fh = 600-1200 mm (connection piece) Vent height Fh = 685-1200 mm (lockcase) Base set n 46831-2 and 46833-2 n 46831-2 n 46833-2 1 20300-620 20300-620 bolt 2 23300-771 23300-771 anti-lift pin 1 30000-530 30000-530 clips 1 30000-600 30000-600 vent run on rest 1 30340-630-1L 30340-630-1L protection piece left 1 30340-630-1R 30340-630-1R protection piece right 2 30330-841-1 30330-841-1 keep 1 41300-500 41300-500 cner transmission 1 45000-550-2 45000-551-2 vent part link arm 1 45140-550-1 45140-550-1 frame part link arm 10 St4.2x16Din7504P St4.2x16Din7504P drilling screw 5 St4.2x25Din7504P St4.2x25Din7504P drilling screw 4 St4.8x32Din7504P St4.8x32Din7504P drilling screw Hinge sets: see chapter E11.14. Connection piece set lockcase: see chapter E11.15..08
3.3. Centre locking sets Vent height Fh = 1201-1800 mm Vent height Fh = 1801-2400 mm 46811-2, 46813-2, 46831-2 46833-2 + Centre locking set n 30140-30 1 30000-515 cner transmission 2 30140-800 keep Windows with vent height from 1201 to 1800 mm require an additional centre locking set n 30140-30. 46811-2, 46813-2, 46831-2 46833-2 + Centre locking set n 35840-31 2 30300-850 mushroom head bolt 2 30540-831 keep 4 St3.9x19Din7504P drilling screw Windows with vent height from 1801 to 2400 mm require an additional centre locking set n 35840-31..09
Vent width Fb = 1201-1400 mm Windows with vent width from 1201 to 1400 mm require an additional centre locking set n 26840-31. 46811-2, 46813-2, 46831-2 46833-2 + Centre locking set n 26840-31 1 30300-850 mushroom head bolt 1 30540-831 keep 1 23300-771 anti-lift pin 2 St4.8x32Din7504P drilling screw 2 St3.9x19Din7504P drilling screw Vent width Fb = 1401-1800 mm 45140-550 45140-551 Only when Fb>1400 mm and Fh<1200 mm 1 46811-2, 46813-2, 46831-2 46833-2 + Additional link arm n 45140-550 45140-551 45000-550-2 45000-551-2 vent part link arm 1 45140-550-1 frame part link arm 46811-2, 46813-2, 46831-2 46833-2 + Centre locking set n 30140-30 1 30000-515 cner transmission 2 30140-800 keep 1 + Additional link arm n 45140-550 45140-551 45000-550-2 45000-551-2 vent part link arm 1 45140-550-1 frame part link arm Windows with vent width from 1401 to 1800 mm require an additional link arm n 45140-550 45140-551. Windows with a vent height Fh<1200 mm and a vent width Fb>1400 mm require an additional centre locking set n 30140-30 (only one keep required) and an additional link arm n 45140-550 45140-551..10
3.4. Selection of rods 3.4.1. With lockcase Only rods when Fh > 1800 mm Positioning by the lowest rod The system consists of 11 rods in synthetic material with different lengths (35000-100, 35000-110,...). The adjustment range of each rod is 50 mm..11
3.4.2. With connection piece set Only rods when Fh > 1800 mm Positioning by the lowest rod The system consists of 11 rods in synthetic material with different lengths (35000-100, 35000-110,...). The adjustment range of each rod is 50 mm..12
3.5. Keep and link arm positions 3.5.1. With lockcase The drawing only shows the situation when the handle is in the middle (A = Fh/2). Imptant! Tighten all clamping screws (grub screws 2.5 mm) with a fce of 1.75 Nm +/-0.25 Nm. Cut-out f anti-lift pin Cut-out f anti-lift pin Cut-out f anti-lift pin.13
3.5.2. With connection piece set The drawing only shows the situation when the handle is in the middle (A = Fh/2). Imptant! Tighten all clamping screws (grub screws 2.5 mm) with a fce of 1.75 Nm +/-0.25 Nm. Cut-out f anti-lift pin Cut-out f anti-lift pin Cut-out f anti-lift pin.14
3.5.3. Link arm positions Imptant! Tighten all clamping screws (grub screws 2.5 mm) with a fce of 1.75 Nm +/-0.25 Nm..15
3.6. Installation instruction Chrono Safe Keeps ATTENTION! (visible hinges) Do not loosen frame part screws befe installation. Tighten screws with fce 5Nm after installation. Imptant! Tighten all clamping screws (grub screws 2.5 mm) of the frame parts with a fce of 1.75 Nm +/-0.25 Nm. Installation high security hook-in keep Slide in keep Tighten the clamping screw Fix the keep after positioning.16
Chrono Invision Pro Safe Keeps Installation of hinges: see page E11.14.08. Imptant! Tighten all clamping screws (grub screws 2.5 mm) of the frame parts with a fce of 1.75 Nm +/-0.25 Nm. Installation high security hook-in keep Slide in keep Tighten the clamping screw Fix the keep after positioning.17
Chrono Invision Go Safe Keeps Installation of hinges: see page E11.14.11. Imptant! Tighten all clamping screws (grub screws 2.5 mm) of the frame parts with a fce of 1.75 Nm +/-0.25 Nm. Installation high security hook-in keep Slide in keep Tighten the clamping screw Fix the keep after positioning.18
4. Tilt windows with hizontally fitted handle 4.1. Base set n 20810-2 (with hook-in keeps) f frame groove 14/18 mm Chrono Safe Chrono Invision Pro Safe Chrono Invision Go Safe Connection: Fb = 600-1200 mm Fb = 600-1200 mm Fb = 600-1200 mm piece set Lockcase: Fb = 685-1200 mm Fb = 685-1200 mm Fb = 685-1200 mm Fh = 420-1200 mm Fh = 540-1200 mm Fh = 570-1200 mm max. 40 kg max. 40 kg Base set n 20810-2 2 20300-620 bolt 2 23300-771 anti-lift pin 2 30000-600 vent run on rest 1 30140-610 frame run on keep 2 30310-841-1 keep with clamping plate 1 30340-630-1L (R) protection piece left (right) 8 St4.2x16Din7504P drilling screw 4 St4.2x25Din7504P drilling screw 4 St4.8x32Din7504P drilling screw + 2x link arm n 722-8-180 Hinge sets: see chapter E11.14. Connection piece set lockcase: see chapter E11.15. Note: the maximum vent weight with link arms n 722-8-180 is 40 kg..19
4.2. Base set n 20830-2 (with hook-in keeps) f frame groove 10/14 mm Chrono Safe Chrono Invision Pro Safe Chrono Invision Go Safe Connection: Fb = 600-1200 mm Fb = 600-1200 mm Fb = 600-1200 mm piece set Lockcase: Fb = 685-1200 mm Fb = 685-1200 mm Fb = 685-1200 mm Fh = 420-1200 mm Fh = 540-1200 mm Fh = 570-1200 mm max. 40 kg max. 40 kg Base set n 20830-2 2 20300-620 bolt 2 23300-771 anti-lift pin 2 30000-600 vent run on rest 1 30140-610 frame run on keep 2 30330-841-1 keep with clamping plate 1 30340-630-1L (R) protection piece left (right) 8 St4.2x16Din7504P drilling screw 4 St4.2x25Din7504P drilling screw 4 St4.8x32Din7504P drilling screw + 2x link arm n 722-13-180 Hinge sets: see chapter E11.14. Connection piece set lockcase: see chapter E11.15. Note: the maximum vent weight with link arms n 722-13-180 is 40 kg..20
4.3. Centre locking sets Vent width Fb = 1201-1800 mm 45140-550 45140-551 Windows with vent height from 1201 to 1800 mm require an additional keep n 30140-800. An additional link arm n 45140-550 ( 45140-551) is required f windows with a vent width of: with connection piece: 1201-1800 mm with lockcase: 1285-1800 mm 20810-2 20830-2 + Keep n 30140-800 + Link arm n 45140-550 45140-551 1 45140-550-1 frame part link arm 1 45000-550-2 45000-551-2 vent part link arm Vent width Fb = 1801-2400 mm 45140-550 45140-551 20810-2 20830-2 + 45140-550 45140-551 + Centre locking set n 26840-31 1 30300-850 mushroom head bolt 1 303540-831 keep 1 23300-771 anti-lift pin 2 St4.8x32Din7504P drilling screw 2 St3.9x19Din7504P drilling screw + Link arm n 45140-550 45140-551 1 45140-550-1 frame part link arm 1 45000-550-2 45000-551-2 vent part link arm Windows with vent width from 1801 to 2400 mm require an additional centre locking set n 26840-31 and an additional link arm n 45140-550 ( 45140-551)..21
4.4. Selection of rods 4.4.1. With lockcase The system consists of 11 rods in synthetic material with different lengths (35000-100, 35000-110,...). Vent width Fb = 685-1285 mm Vent width Fb = 1285-1800 mm Vent width Fb = 1801-2400 mm (only f visible Chrono hinges).22
4.4.2. With connection piece set The system consists of 11 rods in synthetic material with different lengths (35000-100, 35000-110,...). Vent width Fb = 600-1200 mm Vent width Fb = 1201-1800 mm Vent width Fb = 1801-2400 mm (only f visible Chrono hinges).23
4.5. Keep and link arm positions 4.5.1. With lockcase Imptant! Tighten all clamping screws (grub screws 2.5 mm) with a fce of 1.75 Nm +/-0.25 Nm. Vent width Fb = 600-1284 mm Vent width Fb = 1285-1800 mm Vent width Fb = 1801-2400 mm (only f visible Chrono hinges).24
4.5.2. With connection piece set Imptant! Tighten all clamping screws (grub screws 2.5 mm) with a fce of 1.75 Nm +/-0.25 Nm. Vent width Fb = 600-1200 mm Vent width Fb = 1201-1800 mm Vent width Fb = 1801-2400 mm (only f visible Chrono hinges).25
4.6. Installation instructions Chrono Safe Keeps ATTENTION! (visible hinges) Do not loosen frame part screws befe installation. Tighten screws with fce 5Nm after installation. Imptant! Tighten all clamping screws (grub screws 2.5 mm) of the frame parts with a fce of 1.75 Nm +/-0.25 Nm. Installation high security hook-in keep Slide in keep Tighten the clamping screw Fix the keep after positioning.26
Chrono Invision Pro Safe Keeps Installation of hinges: see page E11.14.08. Imptant! Tighten all clamping screws (grub screws 2.5 mm) of the frame parts with a fce of 1.75 Nm +/-0.25 Nm. Installation high security hook-in keep Slide in keep Tighten the clamping screw Fix the keep after positioning.27
Chrono Invision Go Safe Keeps Installation of hinges: see page E11.14.11. Imptant! Tighten all clamping screws (grub screws 2.5 mm) of the frame parts with a fce of 1.75 Nm +/-0.25 Nm. Installation high security hook-in keep Slide in keep Tighten the clamping screw Fix the keep after positioning.28
5. Order tables 5.1. Chrono Safe Chrono Safe f frame groove 14/18 mm with hook-in keeps Handles Handle without base with lockcase Handle + 30000-670CYL (Hizon) 30000-673CYL (Edge) Lockcase + 26300-720 Handle with lockcase Handle + 1852CYL 1857CYL (Sobinox) Lockcase + 26300-721 Handle with connection piece set Handle + 30000-654CYL, 30000-655CYL, 30000-657CYL, 30000-659CYL 30000-662CYL Connection piece + 35300-701 With vertically fitted handle Fb = 650-1200 Fb = 1201-1400 Fb = 1401-1800 Fh = 600-1200 Fh = 685-1200 Fh = 1201-1800 Fh = 1801-2400 + 46811-2 46813-2 + 2x 26140-750 + 46811-2 46813-2 + 2x 26140-750 + 46811-2 46813-2 + 2x 26140-750 + 35840-31 + 46811-2 46813-2 + 3x 26140-750 + 46811-2 46813-2 + 3x 26140-750 + 46811-2 46813-2 + 3x 26140-750 + 35840-31 Transmission rods 35000-... (in accdance with the vent dimensions) + 46811-2 46813-2 + 3x 26140-750 + 45140-550 45140-551 + 46811-2 46813-2 + 3x 26140-750 + 45140-550 45140-551 + 46811-2 46813-2 + 3x 26140-750 + 35840-31 + 45140-550 45140-551 With hizontally fitted handle Fb = 600-1200 Fb = 685-1200 - Fb = 1201-1284 Fb = 1201-1800 Fb = 1285-1800 Fb = 1801-2400 Fh = 400-420 Fh = 421-1200 + 20810-2 + 2x 26140-750 + 2x 722-8-180 + 20810-2 + 3x 26140-750 + 2x 722-8-180 Transmission rods 35000-... (in accdance with the vent dimensions) Note: the maximum vent weight with link arms n 722-8-180 is 40 kg. + 20810-2 + 3x 26140-750 + 45140-550 45140-551 + 20810-2 + 3x 26140-750 + 45140-550 45140-551 + 20810-2 + 4x 26140-750 + 2x 45140-550 2x 45140-551 + 20810-2 + 4x 26140-750 + 2x 45140-550 2x 45140-551.29
Chrono Safe f frame groove 10/14 mm with hook-in keeps Handles Handle without base with lockcase Handle + 30000-670CYL (Hizon) 30000-673CYL (Edge) Lockcase + 26300-720 Handle with lockcase Handle + 1852CYL 1857CYL (Sobinox) Lockcase + 26300-721 Handle with connection piece set Handle + 30000-654CYL, 30000-655CYL, 30000-657CYL, 30000-659CYL 30000-662CYL Connection piece + 35300-701 With vertically fitted handle Fb = 650-1200 Fb = 1201-1400 Fb = 1401-1800 Fh = 600-1200 Fh = 685-1200 Fh = 1201-1800 Fh = 1801-2400 + 46831-2 46833-2 + 2x 26140-750 + 46831-2 46833-2 + 2x 26140-750 + 46831-2 46833-2 + 2x 26140-750 + 35840-31 + 46831-2 46833-2 + 3x 26140-750 + 46831-2 46833-2 + 3x 26140-750 + 46831-2 46833-2 + 3x 26140-750 + 35840-31 Transmission rods 35000-... (in accdance with the vent dimensions) + 46831-2 46833-2 + 3x 26140-750 + 45140-550 45140-551 + 46831-2 46833-2 + 3x 26140-750 + 45140-550 45140-551 + 46831-2 46833-2 + 3x 26140-750 + 35840-31 + 45140-550 45140-551 With hizontally fitted handle Fb = 600-1200 Fb = 685-1200 - Fb = 1201-1284 Fb = 1201-1800 Fb = 1285-1800 Fb = 1801-2400 Fh = 400-420 Fh = 421-1200 + 20830-2 + 2x 26140-750 + 2x 722-13-180 + 20830-2 + 3x 26140-750 + 2x 722-13-180 Transmission rods 35000-... (in accdance with the vent dimensions) Note: the maximum vent weight with link arms n 722-13-180 is 40 kg. + 20830-2 + 3x 26140-750 + 45140-550 45140-551 + 20830-2 + 3x 26140-750 + 45140-550 45140-551 + 20830-2 + 4x 26140-750 + 2x 45140-550 2x 45140-551 + 20830-2 + 4x 26140-750 + 2x 45140-550 2x 45140-551.30
5.2. Chrono Invision Pro Safe Chrono Invision Pro Safe f frame groove 14/18 mm with hook-in keeps Handles Handle without base with lockcase Handle + 30000-670CYL (Hizon) 30000-673CYL (Edge) Lockcase + 26300-720 Handle with lockcase Handle + 1852CYL 1857CYL (Sobinox) Lockcase + 26300-721 Handle with connection piece set Handle + 30000-654CYL, 30000-655CYL, 30000-657CYL, 30000-659CYL 30000-662CYL Connection piece + 35300-701 With vertically fitted handle Fb = 650-1200 Fb = 1201-1400 Fb = 1401-1800 Fh = 600-1200 Fh = 685-1200 Fh = 1201-1800 Fh = 1801-2400 + 46811-2 46813-2 + 44110-10 + 46811-2 46813-2 + 44110-10 + 46811-2 46813-2 + 44110-10 + 35840-31 + 46811-2 46813-2 + 44110-10 + 26110-752 + 46811-2 46813-2 + 44110-10 + 26110-752 + 46811-2 46813-2 + 44110-10 + 26110-752 + 35840-31 Transmission rods 35000-... (in accdance with the vent dimensions) + 46811-2 46813-2 + 44110-10 + 26110-752 + 45140-550 45140-551 + 46811-2 46813-2 + 44110-10 + 26110-752 + 45140-550 45140-551 + 46811-2 46813-2 + 44110-10 + 26110-752 + 35840-31 + 45140-550 45140-551 With hizontally fitted handle Fb = 600-1200 Fb = 685-1200 - Fb = 1201-1284 Fb = 1201-1800 Fb = 1285-1800 Fh = 400-540 Fh = 541-1200 + 20810-2 + 44110-10 + 2x 722-8-180 + 20810-2 + 44110-10 + 26110-752 + 2x 722-8-180 Transmission rods 35000-... (in accdance with the vent dimensions) Note: the maximum vent weight with link arms n 722-8-180 is 40 kg. + 20810-2 + 44110-10 + 26110-752 + 45140-550 45140-551 + 20810-2 + 44110-10 + 26110-752 + 45140-550 45140-551.31
Chrono Invision Pro Safe f frame groove 10/14 mm with hook-in keeps Handles Handle without base with lockcase Handle + 30000-670CYL (Hizon) 30000-673CYL (Edge) Lockcase + 26300-720 Handle with lockcase Handle + 1852CYL 1857CYL (Sobinox) Lockcase + 26300-721 Handle with connection piece set Handle + 30000-654CYL, 30000-655CYL, 30000-657CYL, 30000-659CYL 30000-662CYL Connection piece + 35300-701 With vertically fitted handle Fb = 650-1200 Fb = 1201-1400 Fb = 1401-1800 Fh = 600-1200 Fh = 685-1200 Fh = 1201-1800 Fh = 1801-2400 + 46831-2 46833-2 + 44130-10 + 46831-2 46833-2 + 44130-10 + 46831-2 46833-2 + 44130-10 + 35840-31 + 46831-2 46833-2 + 44130-10 + 26130-752 + 46831-2 46833-2 + 44130-10 + 26130-752 + 46831-2 46833-2 + 44130-10 + 26130-752 + 35840-31 Transmission rods 35000-... (in accdance with the vent dimensions) + 46831-2 46833-2 + 44130-10 + 26130-752 + 45140-550 45140-551 + 46831-2 46833-2 + 44130-10 + 26130-752 + 45140-550 45140-551 + 46831-2 46833-2 + 44130-10 + 26130-752 + 35840-31 + 45140-550 45140-551 With hizontally fitted handle Fb = 600-1200 Fb = 685-1200 - Fb = 1201-1284 Fb = 1201-1800 Fb = 1285-1800 Fh = 400-540 Fh = 541-1200 + 20830-2 + 44130-10 + 2x 722-13-180 + 20830-2 + 44130-10 + 26130-752 + 2x 722-13-180 Transmission rods 35000-... (in accdance with the vent dimensions) Note: the maximum vent weight with link arms n 722-13-180 is 40 kg. + 20830-2 + 44130-10 + 26130-752 + 45140-550 45140-551 + 20830-2 + 44130-10 + 26130-752 + 45140-550 45140-551.32
5.3. Chrono Invision Go Safe Chrono Invision Go Safe f frame groove 14/18 mm with hook-in keeps Handles Handle without base with lockcase Handle + 30000-670CYL (Hizon) 30000-673CYL (Edge) Lockcase + 26300-720 Handle with lockcase Handle + 1852CYL 1857CYL (Sobinox) Lockcase + 26300-721 Handle with connection piece set Handle + 30000-654CYL, 30000-655CYL, 30000-657CYL, 30000-659CYL 30000-662CYL Connection piece + 35300-701 With vertically fitted handle Fb = 650-1200 Fb = 1201-1400 Fb = 1401-1800 Fh = 600-1200 Fh = 685-1200 Fh = 1201-1800 + 46811-2 46813-2 + 44117-10 + 46811-2 46813-2 + 44117-10 + 46811-2 46813-2 + 44117-10 + 26110-752 + 46811-2 46813-2 + 44117-10 + 26110-752 Transmission rods 35000-... (in accdance with the vent dimensions) + 46811-2 46813-2 + 44117-10 + 26110-752 + 45140-550 45140-551 + 46811-2 46813-2 + 44117-10 + 26110-752 + 45140-550 45140-551 With hizontally fitted handle Fb = 600-1200 Fb = 685-1200 - Fb = 1201-1284 Fb = 1201-1800 Fb = 1285-1800 Fh = 400-570 Fh = 571-1200 + 20810-2 + 44117-10 + 2x 722-8-180 + 20810-2 + 44117-10 + 26110-752 + 2x 722-8-180 Transmission rods 35000-... (in accdance with the vent dimensions) Note: the maximum vent weight with link arms n 722-8-180 is 40 kg. + 20810-2 + 44117-10 + 26110-752 + 45140-550 45140-551 + 20810-2 + 44117-10 + 26110-752 + 45140-550 45140-551.33
Chrono Invision Go Safe f frame groove 10/14 mm with hook-in keeps Handles Handle without base with lockcase Handle + 30000-670CYL (Hizon) 30000-673CYL (Edge) Lockcase + 26300-720 Handle with lockcase Handle + 1852CYL 1857CYL (Sobinox) Lockcase + 26300-721 Handle with connection piece set Handle + 30000-654CYL, 30000-655CYL, 30000-657CYL, 30000-659CYL 30000-662CYL Connection piece + 35300-701 With vertically fitted handle Fb = 650-1200 Fb = 1201-1400 Fb = 1401-1800 Fh = 600-1200 Fh = 685-1200 Fh = 1201-1800 + 46831-2 46833-2 + 44137-10 + 46831-2 46833-2 + 44137-10 + 46831-2 46833-2 + 44137-10 + 26130-752 + 46831-2 46833-2 + 44137-10 + 26130-752 Transmission rods 35000-... (in accdance with the vent dimensions) + 46831-2 46833-2 + 44137-10 + 26130-752 + 45140-550 45140-551 + 46831-2 46833-2 + 44137-10 + 26130-752 + 45140-550 45140-551 With hizontally fitted handle Fb = 600-1200 Fb = 685-1200 - Fb = 1201-1284 Fb = 1201-1800 Fb = 1285-1800 Fh = 400-570 Fh = 571-1200 + 20830-2 + 44137-10 + 2x 722-13-180 + 20830-2 + 44137-10 + 26130-752 + 2x 722-13-180 Transmission rods 35000-... (in accdance with the vent dimensions) Note: the maximum vent weight with link arms n 722-13-180 is 40 kg. + 20830-2 + 44137-10 + 26130-752 + 45140-550 45140-551 + 20830-2 + 44137-10 + 26130-752 + 45140-550 45140-551.34
6. General infmation and glass tables The tilt systems Chrono Safe can be used within the Fh/Fb sizes and weight limitations indicated on the charts. The handle height should not be less than 1/3 and not be me than 2/3 of the vent height when the handle is vertically fitted. Technical advise should be sought when the sizes of your windows are not shown in the chart. The systems Chrono Safe are made of non-croding materials, the set should not be installed in crosive atmospheres. Sobinco cannot be held responsible f the malfunctioning of the Chrono Safe system if any non-sobinco parts are used. All parts must be assembled accding to the instructions as described in previous pages. Surface treatment of vent and frame must take place befe assembly of the set to avoid affecting the operation of the gear. If this is not the case, this may lead to the malfunctioning of the hardware and the warranty will dispose. Glazing must be in accdance with national standards. The window and gear should be kept clean and lubricated in accdance with our maintenance instructions (copy available on request). Glass thickness without air gap mm kg/m² 10 25 12 30 14 35 16 40 18 45 20 50 22 55 24 60 26 65 28 70 30 75 32 80 34 85 36 90 38 95 40 100 42 105 Note The glass tables are valid f Chrono Safe, Chrono Invision Pro Safe and Chrono Invision Go Safe. The minimum and maximum dimensions in the charts do not take into account the limitations of the different systems. F the right size range, we refer to page.05..35
With vertically fitted handle Vent height Fh Vent width Fb Vent width Fb Vent height Fh Vent height Fh Vent height Fh Vent width Fb Vent width Fb.36
With hizontally fitted handle Vent height Fh Vent width Fb Vent width Fb Vent height Fh Vent height Fh Vent width Fb Vent width Fb Vent height Fh Vent height Fh Vent width Fb.37