Digital ph transmitter Compact, remote versions for DN 15 to 200 Fully programmable ph transmitter functions for all kinds of ph-measurement tasks Large range of process connections with various fittings Multi language, menu-guided operation Type 8205 can be combined with... Type S020 Type 6642 Type 2731 Type 2030 Type 8644 PLC Fitting Solenoid valve Diaphragm valve for Continuous control On/Off Diaphragm valve Valve islands The ph transmitter is available in different models: Compact ph transmitter with integrated ph electrode Remote ph transmitter, for panel or wall mounting, to connect to the Bürkert ph sensor Type 8200 (max. 10m). Technical data (common to the various versions) General data Display Electrical connections 15 x 60 mm, 8-digit LCD, alphanumeric, 15 segments, 9 mm high shielded cable with max. 1.5 mm 2 cross-section The ph transmitter or sensor can be installed into a pipe by using Insertion fitting Type S020 or other suitable installation materials. It can also be installed in tanks or containers by using an industrial immersion fitting. Environment Relative humidity Standards and approvals Standard EMC Security Vibration Shock 80%, non condensated EN 61000-6-2, EN 61000-6-3 EN 61010-1 EN 60068-2-6 EN 60068-2-27 www.burkert.com Page 1/12
Concept of operation The compact version combines a ph sensor and an electronic module with a display in an IP65 enclosure. The access to the output terminals are provided via two cable glands or a cable plug EN175301-803. Bürkert designed fitting ensures simple direct installation of the Bürkert transmitter into pipes from DN 15 to DN 200. The panel-mounted version consists of an electronic module 8205 integrated in a front-cover. The associated separate ph sensor is Type 8200. The output signals are provided on a terminal strip. The wall-mounted version consists of an electronic module 8205 in an IP65 enclosure. The associated separate ph sensor is Type 8200. The output signals are provided on a terminal strip via cable gland. Operation and display Customized adjustments, such as measuring range, engineering units and alarm setpoints can be carried out menu-supported on site via a multilingual display. The operation is classified according to three levels. Main Menu - ph - temperature - output current - electrode voltage - HOLD function - ph electrode calibration Calibration Menu - language - temperature unit - measuring range 4-20 ma - relay parameter definition - selection of temperature compensation (Pt1000 or manual) - display or not of electrode voltage in main menu - filter selection Test Menu - Offset - Span - temperature adjustment - simulation of ph Direction upwards in menu Choice of digit values Steps from 0 to 9 Direction downwards in menu or sideways for digit selection Relay 2 LED (contact closed) Relay 1 LED (contact closed) Accept of chosen parameter or adjusted value Page 2/12
Compact ph transmitter Type 8205 The sensor component consists of a replaceable combination ph-electrode, screwed into the sensor housing. The measured signal is conveyed to the transmitter via a coax plug. The Pt1000 for automatic temperature compensation is a standard feature in the sensor housing. The transmitter component converts the measured signal, displays the actual value and computes the output signals. Pressure / temperature chart Pressure (bar) 10 9 8 7 6 5 PVDF PVC + PP 4 3 PVC (PN 6) 2 1 PP (PN 6) 0-30 -10 +10 +30 +50 +70 +90 +110 Temperature ( C) A: Application range for complete device (fitting + transmitter) Principle of operation The most important part of the ph transmitter is the ph electrode with its ph selective glass membrane. When the electrode is immersed into the solution, an electrical charge caused by ions (H+) generates a cell voltage between the glass membrane and the solution. This electrical voltage is measured with reference to a reference electrode, located around the ph glass electrode. The cell voltage of the combination electrode is directly proportional to the ph value. The transmitter functions in a two wire circuit (without relay) or three wire circuit (with relays - limits values freely adjustable) and requires a power supply of 12... 30 V DC. A 4... 20 ma standard signal proportional to the ph or to the temperature ( C) is available as output signal. A Metal PVDF (PN 6) General data Compatibility Materials Housing, cover, lid, nut Front panel foil / Screws Cable plug / gland Wetted parts materials Fitting Sensor holder / Pt1000 Seal with all fittings S020 (see corresp. datasheet) PC Polyester /Stainless steel PA Brass, stainless steel 1.4404 / 316L PVC, PP or PVDF PVDF / Stainless steel 1.4571 (316Ti) FKM (EPDM included in delivery) Electrode UNITRODE ph Electrical connections Cable plug EN 175301-803 or cable glands M 20 x 1.5 Complete device data (fitting + electronic module) Pipe diameter DN 15 to 200 ph measurement Measuring range Resolution Accuracy Minimal range Temperature measurement Measuring range Resolution Accuracy Temperature compensation 0... 14 ph 0.01 ph ± 0.02 ph, after proper electrode calibration 0.5 ph unit (i.e 6.7 to 7.2 corresponding to 4-20 ma) -30 to +140 C 0.1 C ± 1 C automatic (integrated Pt1000) or manual (user programmed) - reference temperature 25 C Medium temperature max. with fitting in PVC: 50 C - PP: 80 C - PVDF: 100 C - stainless steel, brass: 130 C Fluid pressure max. PN6 (see pressure / temperature chart) Electrical data Power supply Current consumption with sensor Output Relays (option) Environment Ambient temperature Operation Storage Standards and approvals Protection class Specific technical data Electrode: UNITRODE ph Fluid Measuring range Min. conductivity 12-30 V DC - filtered and regulated 80 ma (with relays) 20 ma (without relay) 4-20 ma programmable (3-wire with relays; 2-wire without relay), proportional to ph or T C max. loop impedance: 1000 Ω at 30 V DC; 750 Ω at 24 V DC; 250 Ω at 15 V DC 2 relays, freely programmable, 3A, 230 V AC 0 to +60 C 4 to 30 C (limited through the electrode) IP65 with cable gland mounted and tightened or blanked if not used - Clean such as drinking water, aquarium, swimming pool - Contamined like effluent rinse water, cooling water, electroplating, paints, cosmetics - with low conductivity such as pure and rainwater - containing sulfides/proteins like tannery, animal breeding, effluent, foodstuffs, cosmetics, biotechnology 0... 14 ph 2 µs/cm (200 kω.cm) Housing glass shaft Fluid pressure 0-6 bar Fluid temperature 0-130 C Max. pressure at max. temperature 4 bar Diaphragm Two clogging free Single pores Reference electrolyte polymer Page 3/12
Installation The 8205 ph transmitter can easily be installed into any Bürkert Insertion fitting system (S020) by just fixing the main nut. Mount the compact ph transmitter in vertical position (max. ±75 ) into a horizontal pipe. The electrode must continuously be immersed into the measuring fluid in order to protect it from drying out. 75 75 The transmitter must be protected from constant heat radiation and other environmental influences, such as direct exposure to sunlight. An industrial immersion kit allows installation of this transmitter into tanks or containers. The following lengths are available: 500, 1000, 1500, 2000 mm. Special lengths on request. Dimensions [mm] Compact version Immersion kit 180 Ø 145 Ø 91 L 110 L [mm] 500 1000 1500 2000 88 88 85.5 21 (190) 123 91 113 88 88 200 116 H 90 126 DN H [mm] [mm] T-Fitting Saddle Plastic St. St. spigot* spigot 15 187 20 185 25 185 32 188 40 192 50 198 223 193 65 198 222 201 199 80 226 209 204 100 231 219 214 110 227 125 234 225 150 244 244 236 180 268 200 280 273 257 * using fusion spigot ( 418652, 418660 or 418644 in PP, PVDF or PE) for orifice DN 65-200 L Ø 75 Ø 104 Ø 145 Page 4/12
Remote ph transmitter Type 8205 (for connection to Bürkert sensor Type 8200) The remote ph transmitter Type 8205 is available in 2 versions: - Panel-mounted ph transmitter General data Compatibility Bürkert ph sensor Type 8200. Materials Housing, cover Front panel foil Screws Cable plug / gland Electrical connections PC (panel-mounted version); ABS (wall-mounted version) Polyester Stainless steel PA Terminals (panel-mounted version) or terminals via 5 cable glands M 16 x 1.5 (wall-mounted version) - Wall-mounted ph transmitter Electrical data Power supply Panel-mounted version Wall-mounted version Current consumption without sensor Sensor input Cable length Output Relay (option) 12-30 V DC filtered and regulated 12-30 V DC filtered and regulated or 115/230 V AC - 50/60 Hz 80 ma (with relays) 20 ma (without relay) Analog signal from ph electrode and Pt1000 max. 10m (distance between sensor and transmitter) 4-20 ma programmable (3-wire with relays; 2-wire without relay), proportional to the ph or T C max. loop impedance: 1000 Ω at 30 V DC; 750 Ω at 24 V DC; 250 Ω at 15 V DC; 2 relays, freely programmable, 3A, 230 V AC A separate compact ph sensor 8200 from Bürkert must be associated with this remote ph transmitter. This sensor Type 8200 must be ordered separately. Environment Ambient temperature Operation and storage 0 to 60 C Standards and approvals Protection class IP65 (panel-mounted and wall-mounted version) IP20 (panel-mounted version, inside the cabinet) Dimensions [mm] Panel-mounted version Wall-mounted version 88 76 41 25 126 23 23 88 120 140 24 48 90 25.5 Page 5/12
Remote ph sensor Type 8200 (for connection to remote Bürkert transmitter Type 8205) A wide range of ph holders enable ph measurement in various applications. General data Compatibility Materials Fitting Sensor holder G2 connection G1 connection Sanitary Triclamp Pt1000 Seal with all fittings S020 (see corresp. datasheet) Brass, Stainless steel 1.4404/316L, PVC, PP or PVDF Stainless steel, PVC, PP, PVDF PVC Stainlesss steel (316Ti / 1.4571), DN40, 50 Stainless steel (316L / DIN 1.4404) Stainless steel 1.4571 (316 Ti) FKM (EPDM option) Electrode Type UNITRODE ph 120 Type LOGOTRODE ph 120 Type MECOTRODE Electrical connections Coaxial shielded cables with connector for ph and 4-wire cable for Pt1000 A complete ph sensor system consists of (see installation example of Type 8200): A. complete armature with seals installed on: 1. Bürkert Fitting (G2 connection) 2. G1 connection 3. Triclamp connection 4. Sanitary connection (according to DIN11851) B. ph-electrode C. Pt1000 (option) D. ph+pt1000 shielded cable (5 or 10 m) Complete device data (fitting + sensor) Pipe diameter DN 15 to 200 Measuring range 0... 14 ph (depends on electrode) Medium temperature max. Temperature compensation with Unitrode ph 120 or Mecotrode and fitting in PVC: 50 C - PP: 80 C - PVDF: 100 C - stainless steel, brass: 130 C with Logotrode ph 120: 50 C automatic (integrated Pt1000) or manual compensation reference temperature 25 C Electrical data Output Analog signal, to be connected to remote electronic module Type 8205 Specific technical data Electrode: LOGOTRODE ph 120 UNITRODE ph 120 MECOTRODE Fluids - Clean like drinking water, aquarium, swimming-pool - Contamined like effluent rinse water, cooling water, electroplating, paints, cosmetics - containing sulfides/proteins like tannery, animal breeding, effluent, foodstuffs, cosmetics, biotechnology - Higher pressure applications Measuring range 2... 14 ph 0... 14 ph 0... 14 ph Fluid pressure / Temperature 0-2 bar / -10 - +60 C 0-6 bar 1) / 0-130 C 0-16 bar 1) / 0-130 C Ambient temperature - Operation Storage 0 to +60 C 4 to 30 C 0 to +60 C 4 to 30 C 0 to +60 C 4 to 30 C Minimal conductivity 2 µs/cm 2 µs/cm 50 µs/cm Max. pressure at max. temperature 2 bar 4 bar 3 bar No. of diaphragms / Diaphragm 1 / single pore 2 / single pore 3 / HP ceramics Reference electrolyte polymer polymer gel 1) only 0-3 bar if used with holder Type 8200 with Triclamp or sanitary connection and with protection tube Page 6/12
Installation of Type 8200 Holder for Type S020 horizontal mounting Holder for connection 1 horizontal mounting D D C A B A. complete armature with seals installed on: 1. Bürkert Fitting S020 (G2 connection) 2. G1 connection 3. Triclamp connection 4. Sanitary connection (according to DIN11851) B. ph-electrode C. Pt1000 (option) D. ph + Pt1000 shielded cable (5 or 10 m) (option) E. PVC adapter piece 1) Holder long version 2) Holder short version A 1) A 2) E* 1 * With standard PVC connection. Not in Bürkert program C 2 B 2 C B 75 75 First select and install the required fitting into a horizontal pipe, according to specific requirements of the sensor and material (temperature and pressure). After having connected the ph sensor to the Type 8205 transmitter and having calibrated the unit, cautiously install the complete ph sensor in vertical position (max. ±75 ) on the fitting. The electrode must continuously be immersed into the measuring fluid in order to protect it from drying out. The sensor must be protected from constant heat radiation and other environmental influences, such as direct exposure to sunlight. Dimensions [mm] ph holder Type 8200 for installation on Bürkert Fitting S020 (G2 connection) - PVC, PP, PVDF, Stainless steel Ø 56 154 30 133 53 (71) Ø 76 Ø 26 Page 7/12
117 18 39.5 Dimensions [mm] ph holder Type 8200 for G 1 connection - PVC short version long version 64 44 Ø 42 Ø 42 154 133 G1 84 104 133 154 G1 Ø 26 Ø 26 ph holder Type 8200 for Triclamp connection - Stainless steel 316L ø A ø B ø 17.2 ø 5 ø 30.1 ø B ø A 2 - DN32 50.5 42.4 2 1/2 - DN40 64 53 Page 8/12
Dimensions [mm] ph holder Type 8200 for sanitary connection (according to DIN 11851) - Stainless steel 316Ti Ø C 117 E 18 39.5 Ø D Ø 17.2 Ø 5 Ø 30.1 DN [mm] ø D ø C E 40 56 48 10 50 68.5 61 11 Measuring chamber for ph transmitter Type 8205 The specially designed measuring chamber enables to install all ph-transmitters or electrodes in all pipe systems, either directly in the main stream or in a by-pass line. Additionnaly it enables to keep the electrode always wet and isolate it easily from the main stream for calibration purposes. ø 60.3 17.6 ø 60 B-B ø 33.6 ø 27 41 62.6 B B 2.70 80.2 Note: Materials: Stainless steel 316L Pipe connection: G1/2 Page 9/12
Combining the ph transmitter Type 8205 with fittings Type S020 Available Fitting DN T- fitting S020 Welding tab S020 Fusion spigot S020 DN15 DN50 DN65 DN65 DN200 ph measurement 8200-8205 compact 8205 remote version Note A Note A: Only with plastic fitting with true union connection DIN8063 Ordering chart - compact transmitter Type 8205 A compact ph transmitter consists of: - an Insertion ph transmitter - an Insertion fitting S020 (DN15 - DN 200) (Refer to corresponding datasheet - has to be ordered separately) Version Voltage supply Output Relays Electrode version Electrical connection DN200 DN15 DN200 DN15 DN32 DN200 Compact 1) 12-30 V DC 4-20 ma None Unitrode ph EN 175301-803 418 834 2 cable glands 418 843 2 Unitrode ph 2 cable glands 418 835 1) FKM gasket in standard; 1 Kit including a black EPDM gasket for the sensor, an obturator for an M 20 x 1.5 cable gland, a 2 x 6 mm multiway seal and a mounting instruction sheet is supplied with each transmitter with cable glands or 1 Kit including a green FKM and a black EPDM gaskets is supplied with each transmitter with connection EN175301-803. Ordering chart - accessories for 8205 ph compact transmitter Specifications Set with 2 cable glands M 20 x 1.5 + 2 neoprene flat seals for cable gland or plug + 2 screw-plugs M 20 x 1.5 + 449 755 2 multiway seals 2 x 6 mm Set with 2 reductions M 20 x 1.5 / NPT1/2 + 2 neoprene flat seals for cable gland or plug + 2 screw-plugs M 20 x 1.5 551 782 Set with 1 stopper for unused cable gland M 20 x 1.5 +1 multiway seal 2 x 6 mm for cable gland + 1 black EPDM 551 775 gasket for the sensor + 1 mounting instruction sheet Ring 619 205 PC- Nut 619 204 Set with 1 green FKM + 1 black EPDM gaskets 552 111 Electrode holder with stainless steel Pt1000 418 889 Electrode holder with titanium Pt1000 418 890 ph electrode 0... 130 C, 0... 6 bar - UNITRODE ph 552 041 Cable plug EN 175301-803 with cable gland (Type 2508) 438 811 Cable plug EN 175301-803 with NPT1/2 reduction (Type 2509) - UR and UL approval 162 673 Page 10/12
Ordering chart - accessories for 8205 ph compact transmitter Compact ph transmitter for tank installation consists of: - an Insertion ph transmitter - an extension cable for immersion fitting - an immersion fitting - a fixing kit - Flange DN65 with stainless steel screws Ordering chart - remote transmitter Type 8205 Remote ph transmitter consists of: - a ph transmitter Type 8205 panel-mounted or wall-mounted version - a ph-holder 8200 - a shielded connection cable (ph and Pt1000 signal) (see Accessories) - a Pt1000 temperature sensor (see Accessories) - an Insertion fitting S020 (DN15 - DN 200) (Refer to corresponding datasheet - has to be ordered separately) ph transmitter Type 8205 panel or wall-mounted version Ordering chart - ph holder for remote transmitter Type 8205 ph-holder Type 8200 without ph-electrode Specifications Sensor version Material Boring for temperature sensor Pt1000 Protection Tube Version Voltage supply Output Relays Sensor version Electrical connect. Specifications Immersion fitting - PP - 0.5 m 419 567 Immersion fitting - PP - 1.0 m 419 568 Immersion fitting - PP - 1.5 m 419 569 Immersion fitting - PP - 2.0 m 419 570 Extension cable for immersion fitting - PP - 0.5 m 416 632 Extension cable for immersion fitting - PP - 1.0 m 416 633 Extension cable for immersion fitting - PP - 1.5 m 416 634 Extension cable for immersion fitting - PP - 2.0 m 416 635 Fixing kit - Flange DN 65 with stainless steel screws 413 615 Panel- 12-30 V DC 4-20 ma None 8200 terminals 427 937 mounted 2 8200 terminals 427 938 Wall- 12-30 V DC 4-20 ma None 8200 cable glands 427 944 mounted 2 8200 cable glands 427 945 115/230 V AC 4-20 ma None 8200 cable glands 427 949 2 8200 cable glands 427 950 ph-holder 8200 for installation on Bürkert fitting standard PVC Yes - 429 228 S020 (G2 connection) PP Yes - 429 229 PVDF Yes - 429 230 Stainless steel Yes - 429 231 ph-holder 8200 for G1 connection thread short PVC Yes - 429 221 long PVC Yes - 429 223 ph-holder 8200 for Triclamp connection DN32 - (dia 50.5 mm) standard Stainless steel 316L Yes Yes 429 235 ph-holder 8200 for Triclamp connection DN40 - (dia 64 mm) standard Stainless steel 316L Yes Yes 429 239 ph-holder 8200 for sanitary connection DN40 - DIN 11851 standard Stainless steel 316 Ti Yes Yes 429 247 ph-holder 8200 for sanitary connection DN50 - DIN 11851 standard Stainless steel 316 Ti Yes Yes 429 255 Page 11/12
Ordering chart - accessories for 8205 remote ph transmitter, 8200 ph sensor ph electrode 0... 50 C, 0... 2 bar, ph 2... 14 - LOGOTRODE ph 120 mm 427 114 ph electrode 0... 130 C, 0... 16 bar, ph 0... 14 - MECOTRODE ph 120 mm 418 319 ph electrode 0... 130 C, 0... 6 bar, ph 0... 14 - UNITRODE ph 120 mm 448 685 Temperature probe -Stainless steel sensor Pt1000 427 023 Shielded connection cable - 5 m (for connection between 8205 transmitter and 8200 sensor) 555 761 Shielded connection cable - 10 m (for connection between 8205 transmitter and 8200 sensor) 555 762 FKM gasket for all holders Type 8200 429 264 EPDM gasket for all holders Type 8200 429 265 Ordering chart - accessories for all version of Type 8205 Specifications Specifications Storage solution for electrodes (KCl 3M), 250 ml 418 557 Buffer solution, 500 ml, ph = 4 418 540 Buffer solution, 500 ml, ph = 7 418 541 Buffer solution, 500 ml, ph = 10 418 543 Factory 2-point ph calibration certificate 550 673 Measuring chamber stainless steel 316L (1.4404) 1) 553 611 1) other materials on request Note: Compact ph transmitter 8205, remote (Wall-mounted or Panel-mounted versions) ph electronic module 8205, ph holder 8200, ph electrode, Pt1000 sensor, connection cable, Insertion fitting S020, have to be ordered separately. Interconnection with other Bürkert products Type 2030 - Diaphragm- Valve with pilot valve Type 2031 - Process Valve with positioner Printer - Type 8205 - Wall-mounted or panel-mounted Type 8205 - Compact ph transmitter Type S020 - Insertion Fitting (see corresp. datasheet) Measuring chamber Type 8200 - ph sensor To find your nearest Bürkert facility, click on the orange box www.burkert.com In case of special application conditions, We reserve the right to make technical changes 0512/1_EU-en_00891800 please consult for advice. without notice. Page 12/12