WARNING l The installation must only be performed by a licensed electrician. l To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA22.1) in Canada. l l Disconnect power before installing the product or servicing it. Wait until fixture has cooled down before installing or servicing the fixture. MIN. 90 C SUPPLY CONDUCTORS MODEL NUMBERS l This installation instructions covers the following products: Power Supply 1. 192W Power Unit: PUG-UNV1-7000 Luminaires 1. LBX1 Series Luminaires Page 1
INSTALLATION INSTRUCTIONS DRIVER ASSEMBLY MOUNTING AND LOW VOLTAGE POWER CONNECTIONS NSF CONFIGURATION (FIGURE 1) 1. Remove driver box cover screws and covers. 2. Route low voltage wires from fixture through wire opening on bottom of driver box on low voltage side. 3. Secure driver assembly to fixture using supplied mounting screws. 4. Make low voltage connections using approved electrical connectors. See wiring diagrams. FIGURE 1 Page 2
INSTALLATION INSTRUCTIONS FIXTURE MOUNTING AND HIGH VOLTAGE POWER CONNECTIONS SUSPENDED MOUNTING (FIGURE 2) 1. Attach suspension system (Rize Enterprises Part Number 30202 or equivalent) to rigid structure. 2. Lift fixture and guide toggle ends of suspension system into mounting holes. 3. Make high voltage connections per appropriate wiring diagram. Attach this end to rigid structure able to support 75 lbs 1 Toggle Mount - Rize eneterprises 30202 or equivalent 2 Mounting Hole FIGURE 2 Page 3
INSTALLATION INSTRUCTIONS FIXTURE MOUNTING AND HIGH VOLTAGE POWER CONNECTIONS PENDANT MOUNTING (FIGURE 3) 1. Remove pendant mounting box cover screw and cover. 2. Secure pendant mounting box by inserting threaded end of 1/2 rigid conduit through conduit opening located on top of the box and secure with 1/2 conduit nuts. 3. Replace pendant mounting box cover and secure with screw. 4. Attach suspension system (Rize Enterprises Part Number 30202 or equivalent) to pendant mounting box. 5. Lift fixture and guide toggle ends of suspension system into mounting holes. 6. Make high voltage connections per appropriate wiring diagram. 1/2 Rigid Conduit 2 1/2 Conduit Nut Box Cover Pendent Mounting Box Box Cover Screw Toggle Mount - Rize enterprises 30202 or equivalent 4 1 3 5 Mounting Hole FIGURE 3 Page 4
INSTALLATION INSTRUCTIONS FIXTURE MOUNTING AND HIGH VOLTAGE POWER CONNECTIONS TANDEM MOUNTING (FIGURE 4) 1. Place fixture face down, side by side on flat surface. 2. Using tandem mounting bracket and screws, attach bracket to fixtures, both sides. 3. Lift fixture and guide toggle ends of suspension system into mounting holes. 4. Make high voltage power connections per appropriate wiring diagram. Attach this end to rigid structure able to support 150 lbs 2 Mounting Screw Tandem Mounting Bracket Mounting Hole 3 FIGURE 4 Page 5
INSTALLATION INSTRUCTIONS STEP DOWN TRANSFORMER INSTALLATION SINGLE FIXTURE (FIGURE 5) 1. Remove pendant mounting box cover screw and cover. 2. Secure pendant mounting box by inserting threaded end of 1/2 rigid conduit through conduit opening located on top of the box and secure with 1/2 conduit nuts. 3. Make wiring connections to step-down transformer per wiring diagrams. 4. Replace pendant mounting box cover and secure with screw. 5. Attach suspension system (Rize Enterprises Part Number 30202 or equivalent) to pendant mounting box. 6. Lift fixture and guide toggle ends of suspension system into mounting holes. 7. Make wiring connections to driver box per appropriate wiring diagram. Note: This configuration is not wet rated and does not qualify for NSF rating 1/2 Rigid Conduit 2 1/2 Conduit Nut Box Cover Pendent Mounting Box Box Cover Screw Toggle Mount - Rize enterprises 30202 or equivalent 5 1 4 6 Mounting Hole FIGURE 5 Page 6
INSTALLATION INSTRUCTIONS OCCUPANCY SENSOR INSTALLATION SINGLE FIXTURE (FIGURE 6) 1. Attach occupancy sensor assembly to fixture using supplied mounting screws. 2. Make wiring connections per appropriate wiring diagram. FIGURE 6 Page 7
INSTALLATION INSTRUCTIONS OCCUPANCY SENSOR INSTALLATION TANDEM FIXTURE (FIGURE 7) 1. Attach occupancy sensor assembly to fixture using supplied mounting screws. 2. Make wiring connections per appropriate wiring diagram. 1 FIGURE 7 Page 8
WIRING DIAGRAMS WITH NO DIMMING CONFIGURATION WITH DIMMING CONFIGURATION Page 9
WIRING DIAGRAMS DIMMING AND TRANSFORMER CONFIGURATION Page 10
WIRING DIAGRAMS TANDEM MOUNT WITH NO DIMMING CONFIGURATION Page 11
WIRING DIAGRAMS TANDEM MOUNT WITH DIMMING CONFIGURATION Page 12
WIRING DIAGRAMS TANDEM MOUNT WITH DIMMING AND TRANSFORMER CONFIGURATION Page 13
Page 14
Page 15