INSTALLATION INSTRUCTIONS Accessory S P/N 08P00-T0A-00 Application 04 CR-V Publications No. AII 50030 Issue Date JULY 03 PARTS LIST TOOL AND SUPPLIES REQUIRED Phillips screwdriver Pushpin Left front splash guard Stubby Phillips screwdriver Illustration of the Splash Guards on the Vehicle Right front splash guard RIGHT Left rear splash guard Right rear splash guard Q0D00AG INSTALLATION 7 Washer-screws 4 Spring nuts Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Be careful not to damage the body paint finish. Clean and wax the areas to be covered with a highquality paste wax. Clips 03 American Honda Motor Co., Inc. All Rights Reserved. AII 50030 (307) 08P00-T0A-000-90 of 5
Installing the Front Splash Guards. Turn the steering wheel fully counterclockwise. 4. Install the left front splash guard to the left front inner fender with one washer-screw and two self-tapping screws removed in step 3 in the order. NOTE: Check there is no gap between the left front loosen the one washer-screw and two self-tapping screws, hold the splash guard against the body, and retighten the screws. WASHER-SCREW INNER FENDER Q0D00AG. Using a pushpin, pierce the center of upper clip on the left front inner fender. 3. Remove two self-tapping screws from the left front inner fenderwell. INNER FENDERWELL 3 SELF-TAPPING SCREW (reuse) LEFT Q0D004BG 5. Turn the steering wheel fully clockwise, and repeat steps through 4 to install the right front splash guard. SELF-TAPPING SCREW Q0D003AG of 5 AII 50030 (307) 03 American Honda Motor Co., Inc. All Rights Reserved.
Installing the Left Rear Splash Guard 6. Remove and discard one clip from the rear under cover. 8. Install two spring nuts into two holes on the rear bumper. Install the spring nuts in the direction shown. HOLE UNDER COVER Discard. Q0D030BG SPRING NUT Q0D030AG 7. Using a pushpin, pierce the rear bumper through the two indentation marks. 9. Install the left rear splash guard to the rear bumper with two washer-screws in the order. NOTE: Check there is no gap between the left rear loosen the two washer-screws, hold the splash guard against the body, and retighten the screws. INDENTATION MARK Q0D005BG WASHER-SCREW Q0D0303BG 03 American Honda Motor Co., Inc. All Rights Reserved. AII 50030 (307) 3 of 5
0. Secure the left rear splash guard to the rear under cover with one new clip.. Using a pushpin, pierce the center of inner clip on the right rear inner fender. UNDER COVER INNER FENDER NEW QA00AG Installing the Right Rear Splash Guard. Remove and discard one clip from the right rear wheel arch protector. Q0D0305BG 3. Using a pushpin, pierce the rear bumper through the two indentation marks. WHEEL ARCH PROTECTOR Discard. Q0D0306AG INDENTATION MARK Q0D0307BG 4 of 5 AII 50030 (307) 03 American Honda Motor Co., Inc. All Rights Reserved.
4. Install two spring nuts into the two holes on the rear bumper. Install the spring nuts in the direction shown. 6. Secure the right rear splash guard to the right rear wheel arch protector with one new clip. WHEEL ARCH PROTECTOR HOLE SPRING NUT Q0D0308AG NEW QA00AG 5. Install the right rear splash guard to the rear bumper with three washer-screws in the order. NOTE: Check there is no gap between the right rear loosen the three washer-screws, hold the splash guard against the body, and retighten the screws. 3 RIGHT 3 WASHER-SCREWS Q0D030BG 03 American Honda Motor Co., Inc. All Rights Reserved. AII 50030 (307) 5 of 5