ML640, ML740 Non-Spring Return Electric Linear Valve Actuators EATURES Quick and easy installation. No separate linkage required. Conduit connector is standard. No adjustments required. Low power consumption. High close-off ratings. orce-limiting end switches. Manual operator. Synchronous motor. PRODUCT DATA APPLICATION The ML640 Non-Spring Return Electric Linear Valve Actuators are floating control actuators used with controllers that provide a switched or floating single-pole double-throw (spdt) output. These actuators operate standard Honeywell valves in heating, ventilating, and air conditioning (HVAC) applications. Corrosion resistant design. Maintenance free. Direct/reverse acting with ML740. Position feedback signal included with ML740. Selectable 0 to 0 Vdc or to 0 Vdc signal input with ML740. The ML740 Non-Spring Return Electric Linear Valve Actuators are modulating control actuators used with controllers that provide an analog output of 0 to 0 Vdc or to 0 Vdc. These actuators operate standard Honeywell valves in HVAC applications. An internal selector can be used to reverse the direction of action. Contents Application... Installation... Ordering Information... Operation... 6 Checkout... 7 6-5-04
SPECIICATIONS Models: Model Run Time in sec at 60 Hz a Dependant on actuator model. Dimensions: See ig.. Weight:.9 lb (. kg). Electrical Ratings: Power Input: 4 Vac ±5%, 60 Hz. Power Consumption: ML640: 6 VA maximum at 4 Vac. ML740: 7 VA maximum at 4 Vac. Signal Source Output Resistance: K ohm maximum. Signal Load: ma maximum. Ambient Ratings: Temperature: Ambient: 4 to (-0 C to 50 C). Storage: -40 to 58 (-40 C to 70 C). Maximum Valve Medium: 00 (50 C). Humidity: 5 to 95 percent relative humidity, noncondensing. Stem orce: 5 lbf (600N). Stroke in in. (mm) Description ML640A 0 or 60 a /4 (0) Electric Linear ML740A Valve Actuator Signal Inputs (Supply Voltage Between Terminals): ML640: B and 4 Vac: Drives valve stem down. W and 4 Vac: Draws valve stem up. ML740: 0 to 0 Vdc or to 0 Vdc. Actuator Material: Cover: ABS-R plastic. Base: PBTP-R plastic. Yoke: Diecast aluminum. Actuator Stroke: /4 in. (0 mm). Close-off Pressure Ratings: See Table. Protection Standard: IP54. Approvals: Canadian Standards Association Listed. Underwriter s Laboratories, Inc. UL94-5V lame Retardant. Meets CE requirements. Cable entry: Conduit connector and one knockout on case. Accessories: 496000-00 High Temperature Kit (for actuators with /4 in. stroke) Increases temperature range high-end to 48 (0 C). or ML640 49679- Single Auxiliary 0K ohm Potentiometer. 49679- Single Auxiliary 0 ohm Potentiometer. 49680-05 Dual Auxiliary Switch (for 4 Vac use only). Table. Close-off ratings for ML640, ML740 Electric Linear Valve Actuators and Honeywell Valves (psi). Type Valve / in. /4 in. in. -/4 in. -/ in. in. -/ in. in. lange V50A 8 6 V50/5/450/45 4 V50B,C; V60/6/460/46 a 4 a NPT V50,G 50 b 50 b 50 b 4 b 77 49 8 6 V50H,J 50 50 50 45 V50Nxxx, V50Nxxx, V50N 0 0 6 04 67 7 V50Nxxx 00 00 00 00 V50 50 50 50 6 77 49 a Represents maximum pressure difference between the outlet and either of the two inlets. b Do not exceed 00 psi with V50G valves used in steam applications. ORDERING INORMATION When purchasing replacement and modernization products from your TRADELINE wholesaler or distributor, refer to the TRADELINE Catalog or price sheets for complete ordering number. If you have additional questions, need further information, or would like to comment on our products or services, please write or phone:. Your local Honeywell Environmental and Combustion Controls Sales Office (check white pages of your phone directory).. Honeywell Customer Care 885 Douglas Drive North Minneapolis, Minnesota 554-486. http://customer.honeywell.com or http://customer.honeywell.ca International Sales and Service Offices in all principal cities of the world. Manufacturing in Belgium, Canada, China, Czech Republic, Germany, Hungary, Italy, Mexico, Netherlands, United Kingdom, and United States. 6-5 04
/ () PT YOKE DIAMETER -/8 (5) M749 5-5/5 (5) -/6 (67) x 6-5/6 (6) 5-9/6 (4) 9-/6 () -/6 () MINIMUM CLEARANCE 9-9/6 (4) Mounting. Place the actuator on the valve with the U-bolt around the valve collar. See ig... Place the U-bolt against the valve collar and secure the actuator to the valve by turning each U-bolt nut clockwise. NOTE: To assure even pressure on the collar, first tighten the nuts finger-tight and then alternate turning each U-bolt nut until both are snug.. Push aside the stem button retaining clip and hold. See ig.. 4. Lift valve stem until the head of the valve stem button is inside the large slot of the stem button retaining clip on the actuator. 5. Release the stem button retaining clip to secure the stem button. Check to make certain the stem button is secured by the retaining clip. 6. Remove the cover from the actuator using a Phillips or crosspoint screwdriver. See ig. 4. ig.. Approximate dimensions of ML640, ML740 Electric Linear Valve Actuator in in. (mm). INSTALLATION When Installing this Product.... Read instructions carefully. ailure to follow them could damage the product or cause a hazardous condition.. Check ratings and description given in the specifications to make sure the product is suitable for your application.. Installer must be a trained, experienced service technician. 4. After installation is complete, check out product operation as provided in these instructions. Electrical Shock or Equipment Damage Hazard. Can shock individuals or short equipment circuitry. Disconnect power supply before installation. M66 ig.. Attaching actuator to valve collar. Location Install the actuator in a location that allows enough clearance for mounting accessories and for servicing. Equipment Damage Hazard. Can damage actuator due to condensation or a valve gland leak. Install the actuator in a position above horizontal. M66 ig.. Securing actuator to valve. 6-5 04
M660 ig. 5. Connecting power and control wiring. Wiring M740 ig. 4. Removing actuator cover. Electrical Shock or Equipment Damage Hazard. Can shock individuals or short equipment circuitry. Disconnect power supply before installation. T6984 (LOATING CONTROLLER) MOTOR OPEN MOTOR CLOSE 4 Vac COMMON POWER SUPPLY. PROVIDE DISCONNET MEANS 4 ML640A,B T T W B O All wiring must comply with local electrical codes, ordinances and regulations. Voltage and frequency of the transformer used with the actuator must correspond with the power supply and actuator characteristics. See ig. 6 through for typical wiring hookups.. eed power and control wires through the conduit connector located on the bottom of the actuator case. See ig. 5. Equipment Damage Hazard. Conduit connection or removal can break an unsupported connector. When removing or attaching conduit, use a wrench to support the motor connector.. Using the wiring diagram in ig. 6, connect power and control wires. Make sure that all wiring is correct.. or ML740 only: Check the selector for proper settings. See Signal Input ailure section for details. 4. When wiring is complete, replace the actuator cover. See ig. 7. 5. Apply power and control signals to the actuator. 4 ALL BLOCKS HAVE THE SAME NUMBER O TERMINALS (8), BUT THE ONLY TERMINALS THAT ARE ACTIVE ON THIS BLOCK ARE T, T, W, AND B. THE T-Y-G TERMINALS ARE A THREE TERMINAL BLOCK SEPARATE ROM THE MAIN BLOCK. THEY DO NOT APPEAR ON ALL MODELS BECAUSE THEY ARE OR A SINGLE EEDBACK POTENTIOMETER (0K OR 0 OHMS). THE REQUIRED BLOCKS ARE PART O THE POTENTIOMETER ACCESSORY KITS. MOTOR OPEN SIGNAL DRAWS VALVE STEM UPWARDS. MOTOR CLOSE SIGNAL DRIVES VALVE STEM DOWNWARDS. ML740 T T O O ig. 6. ML640 wiring. INPUT (EEDBACK) OUTPUT T Y G L L M766 L L AND OVERLOAD PROTECTION AS REQUIRED. -0 Vdc EEDBACK SIGNAL. SEE OUTPUT SIGNAL EEDBACK SECTION. 0-0 Vdc OR -0 Vdc CONTROL SIGNAL. SEE SIGNAL INPUT () SECTION. M74 ig. 7. ML740 wiring using feedback output from a controller with a common transformer. 6-5 04 4
ML740 T T O O 4 5 6 T775 (WITH -0 VDC OUTPUT) L L ig. 8. ML740 wiring using a to 0 Vdc control signal and separate transformers. SENSOR L L DUAL TRANSORMERS M74 ML740 T T O O 4 5 6 500 OHM RESISTOR T775 (WITH 4-0 MA OUTPUT) SENSOR ig.. ML740 wiring using a 4 to 0 ma control signal and a common transformer. L L SINGLE TRANSORMER 40 VA 4 VAC M746 ML740 T T 4 5 6 SENSOR L L SINGLE TRANSORMER 40 VA 4 VAC DIRECTION O ACTION W INPUT SIGNAL RANGE W INPUT SIGNAL AILURE W O LED M40 O T775 (WITH -0 VDC OUTPUT) ig.. Pushbuttons and potentiometer (default positions). M744 ig. 9. ML740 wiring using a to 0 Vdc control signal and a common transformer. ML740 4 5 6 SENSOR T T L L DUAL TRANSORMERS O O 500 OHM RESISTOR T775 (WITH 4-0 MA OUTPUT) M748 ig.. Replacing actuator cover. L L M745 ig. 0. ML740 wiring using a 4 to 0 ma control signal and separate transformers. 5 6-5 04
Auxiliary Potentiometers The 49679 Auxiliary Potentiometers can be used as feedback potentiometers and to provide remote indication of valve position. See the Installation Instructions packed with the potentiometers. Auxiliary Switches The 49680 Dual Auxiliary Switch can be used on both the ML640 and ML740 Electric Linear Valve Actuators. Switching points are adjustable over the full length of the actuator stroke; for example, the switch can be used to switch pumps or to provide remote indication of any stroke position. See the Installation Instructions packed with the auxiliary switch. Equipment Damage Hazard. Improper voltage damages the auxiliary switch beyond repair. Use the 49680 Dual Auxiliary Switch only with 4 Vac applications. OPERATION General In the actuator, the drive of a synchronous motor is converted into the linear motion of the actuator stem by using a spur gear transmission. A button retainer clip connects the actuator stem to the valve stem. Manual Operation The ML640 and ML740 are equipped with a manual operator knob (see ig. 4) to open or close the valve in the event of power failure:. Turn off or disconnect the power supply before manually operating the actuator.. Push down on the manual operator knob and turn the knob: a. Counterclockwise to drive the stem downward. b. Clockwise to draw the stem upward. IMPORTANT Manual operation allows very high closing force that can jam the actuator spindle, exceed the force switch ratings, and stop the motor. After a manual valve close-off operation, release the spindle one turn by turning the manual operator knob. This will ensure automatic disengagement of the manual operator upon power resumption. NOTE: If the manual operator knob is not pushed in while turned, it will rotate only a short distance before disengaging without power resumption. ML740 Signal Input () ig. 4. Manual operator knob. The range of the analog input signal () can be changed by pressing the right-hand pushbutton (W) located on the printed circuit board (see ig. ). If the corresponding LED is lit, this indicates that the actuator is set for 0 to 0 Vdc operation (factory setting); if it is dark, the actuator is set for to 0 Vdc operation. Signal Input ailure Using the potentiometer (W) located on the printed circuit board (see ig. ), the actuator can be adjusted such that in case the signal input fails (e.g., due to a broken wire) or exceeds.5 V, the actuator will run to any pre-configured position between 0% and 00%. The factory setting is with the actuator stem in the central position (50%). NOTE: The two pushbuttons (W and W) and the potentiometer (W) are accessible after the cover has been removed and are located at the rear side of the protection sheet of the printed circuit board. Output Signal eedback () M6640 An analog output signal ( to 0 Vdc) that represents the actual actuator stem position is available at terminal. It can be used for remote indication of the stem position. When the actuator stem is fully downward, the output signal is 0 Vdc. When the valve stem is up, the output signal is 0 or Vdc. The output of the signal does not change when the action of the actuator is reversed using W. See Direction of Action. Actuator Override To override the control signal (for freeze protection or similar applications), connect the 4 Vac common (T) to either terminal O or O. Connecting to terminal O fully extends the actuator stem. Connecting to O fully retracts the actuator stem. 6-5 04 6
The control signal () is ignored when the override signal is applied to terminal O or O. This override can be achieved with a switch or a relay. See ig. 5. ML740 T T O O INPUT (EEDBACK) OUTPUT SPT OVERRIDE SWITCH 4 Direction of Action (ML740 only) The direction of action can be reversed by pressing the lefthand pushbutton (W) located on the printed circuit board (see ig. ). If the corresponding LED is lit, this indicates that the actuator stem will be up at a control signal of 0() Vdc (factory setting); if it is dark, the actuator stem will be down at a control signal of 0() Vdc. L L 4-0 Vdc EEDBACK SIGNAL. SEE OUTPUT SIGNAL EEDBACK SECTION. 0-0Vdc OR -0 Vdc CONTROL SIGNAL. SEE SIGNAL INPUT () SECTION. SEE OVERRIDE SECTION OR DETAILS ON OVERRIDE OPERATION. M749 ig. 5. Connections for overriding control signal to drive ML740 to a specific position. CHECKOUT The actuator can be checked out either directly or by using a controller. Direct Checkout. Mount the actuator for the required application; see Installation section.. Check the valve position and make sure that 4 Vac is correctly applied to the actuator.. Apply the power to the appropriate leadwires to move the valve. 4. If the actuator does not move, make sure the actuator is properly installed/wired. 5. If the actuator installation and wiring are both correct and the actuator does not run, replace the actuator. Controller Checkout. Adjust the setpoint of the controller to call for opening the valve. Observe the actuator.. If the valve is closed, it should begin to open.. If the valve remains closed, move the setpoint further toward the open setting. 4. If the valve does not move, check for 4 Vac in the actuator power input. 5. If 4 Vac is present and the actuator does not operate, check the voltage across the controller leadwires to determine if the device is miswired. 6. If the wiring is correct, 4 Vac is present on the power input terminals, and the actuator does not run, replace the actuator. 7 6-5 04
Automation and Control Solutions Honeywell International Inc. 985 Douglas Drive North Golden Valley, MN 554 customer.honeywell.com U.S. Registered Trademark 0 Honeywell International Inc. 6-5 04 M.S. Rev. 0- Printed in United States