Caution Please read the following manual closely and familiarize yourself with its contents before operating the model. Keep the manual in a safe place for future reference for repairs, part numbers and assembly instructions. This product is not a toy and intended for ages 4 and up. Adult supervision is required for ages under 8 years old. Contains small parts, keep out of reach of children years and younger. DO NOT operate this model in the rain, on public streets, near crowds, airports or anywhere where it will be deemed a hazard to anyone or anything. Do not run the model into yourself, others or animals while operating or possible injury may occur. Serious accidents, personal injury and property damage may occur. Electronic Speed Controller Instructions Use proper rechargeable batteries intended for RC applications only. Follow manufacturers guidelines for charging batteries properly. Motor and speed control can become very hot after use, please handle with care. Be aware of all moving parts of the vehicle so no injuries occur. Always unplug the battery after use. DO NOT leave your car unattended with the battery plugged in and do not store the battery in the vehicle. Always store batteries and models in a cool dry place. Operating Instructions: Place the model on a car stand or something that holds all 4 wheels off the ground. Turn on the ESC. Right after powering up the ESC will denote a series of beeps denoting the neutral setting of the transmitter. A second beeping sound denotes the success of neutral setup. If you do not hear the second set of beeps power the esc down, then the transmitter and begin again. Adjust & make sure the Throttle forward direction coincides with the ESC forward direction. With the wheels of the model off the ground safely push the throttle trigger forward to start motor running, push the throttle trigger backwards & hold it. If the system keeps braking, the throttle forward direction coincides with the ESC forward direction. Otherwise, if the system only has brief braking then the motor begins reverse operation, the throttle and ESC forward directions do not coincide with each other. In this case you can adjust the throttle reversing switch on the transmitter. First change the switch for the throttle direction then turn the ESCoff and back on again to reset. If the motor is operating in the wrong direction compared to the throttle inputs switch any two motor wires while the ESC is turned off. Precautions Do not reverse the battery wire connections! Reversing the battery polarity will permanently damage the ESC. Once the battery pack is connected, handle the model with extreme care, making sure you are clear of all rotating parts. Be sure to turn off the ESC power before turning off the transmitter. Connect the battery pack just before driving and disconnect it immediately after your done. Never leave battery packs plugged into your model during storage; batteries should not be stored in your model ever. Always make sure you are connecting the ESC to a proper power source that has the correct voltage & polarity. Input voltage: 7.V-8.4V(Ni-cd & Ni-MH) 7.4V(Li-po) only. Any higher voltage will cause permanent damage and will void the warranty! Incorrect voltages or reversed polarity will damage the ESC. Avoid touching ESC heat sink or motor casing right after operation due to high temperatures and the risk of burning your hands. Water and electronics don t mix! Never let water or any other debris on or inside of the ESC or motor. Any issue related to ESC failure due to water voids the warranty. Always maintain wiring away from rotating parts that can cause damage or wear wiring over time. Cover any exposed wires using heat shrink. Gear Selection It is very important not to overheat the ESC or motor. When adjusting gear ratios always test both the ESC and motor temperature after running for - minutes. It is very important not to heat the motor or speed control over 80 degrees Fahrenheit. Doing so will decrease performance and could ruin your electronics. Forward operation includes brakes while throttle is at more than 5% input. Slower than 5% will begin reverse operation. Reverse will also begin from a standstill. Trouble-shooting Steering Channel Works But Motor Will Not Run Check input plug wiring connections at ESC and receiver. Check motor connections. Possible internal motor damage. Check vehicle s drive train for free operation. Possible ESC thermal shutdown Check gear ratio & free operation of drive train for possible overheating/esc is being severely overheated allow system to cool & return throttle to neutral position to regain motor control. Possible receiver failure Check operation with a different receiver. Possible internal damage Refer to Service Procedures. Receiver Glitches/Throttle Stutters During Acceleration Receiver or antenna too close to ESC, power wires, battery, or motor. Bad connections Check wiring & connectors. Low voltage to receiver Try Glitch Buster capacitor on receiver. External Power Capacitor damaged/not installed Replace Power Capacitor. Battery pack damaged or weak Try a different battery pack. Motor s magnet has weakened or overheated Replace rotor. Motor and Steering Servo Do Not Work Check wires, receiver signal harness wiring & color sequence, radio system, crystals, battery/motor connectors, & battery pack. Power wires too close to signal wires Do not bundle power & signal wires together. Possible receiver failure Check operation with a different receiver. Possible internal damage Refer to Service Procedures. Brushless Motor Runs Backwards Switch any two motor wires while the ESC is turned off. Speed Control Runs Excessively Hot Gear ratio too low Increase gear ratio (see GEAR SELECTION ). Model Runs Slowly/Slow Acceleration Gear ratio too high Reduce gear ratio (see GEAR SELECTION ). Check battery & connectors Try another battery; replace connectors/battery if needed. Incorrect transmitter/esc adjustment Refer to Step 4. External Power Capacitor damaged/not installed Replace Power Capacitor. Needle Nose Pliers Awl RCE00 HD Grease Thread Lock RCE60 Fusion Tire Glue RCE004 Super Diff Lube RCE705 Body Reamer Wire Cutters RCE7045 Body Scissors RCE005 Black Grease Hex Wrench Box Wrench RCE708 Hobby Knife
Battery Battery Charger (Not Included) Motor... 4. Install Transmitter Batteries Connect Battery to ESC Switch on Transmitter First Switch on ESC Second Note: When done driving Turn Off the ESC First and the Transmitter Second Servo Receiver Electronic Speed Controller / Switch 6 0 7 8 9 4 5 GLG0.4GHz Control Panel Steering Wheel Throttle Trigger 4 Battery Compartment 5 Charging Jack 6 Sterring Servo Reverse 7 Power LED 8 Steering Trim 9 Bind Button 0 Throttle Servo Reverse Battery Voltage Steering Dual Rate Power Switch 4 Throttle Trim 4
Front Suspension T0056 T0056 T004 T0008 T0056. E-ring T0056 T007 4 T0056 T0056 x4.5 Hinge pin front inner T0056 T004 T0056 L R Front Suspension T0059 T0059 T005 T047 4 T008 Mx5 Screw 4 5 T006 T0059 Ball stud - long T008 Assemble in the specified order L R Assemble left and right sides the same way
Buffer T0080 0 T0080 T00 9 T004 T004 T004 8 5 T06 T004 T00 4 7 T004 4.0 E-ring T0080 T00 6 T0080 x6x.5 Ball Bearing 4.0mm 4 T004 T06 Ball stud - silvery T0080 4 Buffer T0044 T0044 4.5x5.4 Block Carrier T0044 Mx0 Screw T0060 T0044 T0060 T0060 Ball stud - short T0044 x7x0.8 Washer T0044 T0044 T004 Assemble in the specified order
5 Front Suspension T008(x0) T008(x0) T008(x8) 5 T047 T000 T008 Mx8 Screw T008 Mx0 Screw 6 T008(x0) T047 Mx5 T008(x0) T047 Mx5 Screw 6 Front Suspension <Right> T0054. E-ring 8 T004 4.0 E-ring T0054 x7.5 Hinge pin front outer 4 T0060 Ball stud-short 4 T004 x9.8 Shaft T0079 5x0x4 Ball bearing 4 T0054 T00 T004 T004 4 T0060 T00 T0060 5 T004 L R T0054 8 <Left> T0054 7 T0054 T0079 T0054 T0054 6 T0079 T004 Assemble in the specified order L R Assemble left and right sides the same way
7 Front Suspension T009 approx.8mm Front Upper(Right) x : T009 approx.8mm Front Upper (Left) x : T009 4.8mm Ball End(Long) 8 T009 x54 Turnbuckle T009 approx.4mm Steering Tip x : 4 8 Front Suspension 9 Front Suspension T008(Mx) T07 T008(Mx) T07 T008(Mx0) T09 T008 Mx Screw T008 Mx0 Screw 4 T07 Upper Shock Bushing Assemble as many times as specified x : Ture-to -scale diagram 4
0 Differential T054 8T Gear T054 5.xx0. T054 x8.8 T056 4.8x.6 T054 4T Gear T057 Diff Gear Shaft T0078 0x5x4 Ball Bearing T05 5T Diff Gear T054 x8.8 Pin T056 4.8x.6 O-ring T0078 0x5x4 T054 5.xx0. Washer T055 Gear Differential Outdrives Differential T054 8T Gear T05 M.5x8 T054 x8.8 T0078 0x5x4 Ball Bearing T054 5.xx0. T056 4.8x.6 T054 x8.8 Pin T05 Gear Differential Seal T056 4.8x.6 O-ring 000# T054 5.xx0. Washer T05 5T Diff Gear Cover T055 Gear Differential Outdrives High grip: Suggest using 500#-000# differential oil; Low grip: Suggest using 500#-700# differential oil. T05 M.5x8 Screw 4 T0078 0x5x4 5
Transmission T0079 5x0x4 T004 T050 Gear Differential Case-R T005 0T T005 T0079 5x0x4 TS0 8T T0079 5x0x4 T0079 5x0x4 Ball bearing 4 T005 5x6.8 Idler gear shaft T004 5x8x6.7 Top shaft spacer T050 Gear Differential Case-L Motor mounts Screw Cement T008 x5 T008 Mx Screw T008 Mx5 Screw T008 x 4 T006 Apply grease Screw Cement Apply threadlocker(screw cement) 6
4 Main Gear T0084 M4 Flanged Nylon Nut T008 T04 T09 T008 T04 approx.8mm T0040 T0084 5 Rear Damper Tower T00 T008(Mx) T008(Mx0) T008(Mx) T008 Mx0 Screw 4 T07 T008 T008 Mx Screw T07 T07 Upper Shock Bushing 7
6 Rear Bulkhead T008 T008 T008 T0059 T0059 Ball stud - long T008 Mx0 Screw 4 7 Rear Chassis T004 T05 T008 Mx8 Screw T008 8
8 Rear Suspension T004 T0055 x48 Hinge pin Rear inner T005 T008 Mx8 Screw T008 T0055 L R 9 Rear Suspension T008 Mx0 Screw 4 T008 9 L R Assemble left and right sides the same way
0 Rear Transmission T008 T008 Mx0 Screw T008 Mx8 Screw T008 Rear Shock Tower & Rear Fender T008(x0) T008 Mx8 Screw 5 T008 Mx0 Screw 4 T008(x8) 4 T006 T008(x8) Screws which were semi tightened in P9 8 8 Assemble in the specified order 0
Rear Suspension L R <Left> <Right> T05 T00 T0079 T0060 T0060 Ball stud - short T004 x9.8 Shaft T0079 5x0x4 Ball bearing T0079 T004 T004 4 Rear Suspension L R T0057 T00 T0057. E-ring 4 T0057 T0057 T00.x6x Plastic Washer T0057 x0.5 Hinge pin Rear outer L R Assemble left and right sides the same way Apply grease
4 Rear Suspension T009 4.8mm Ball End(Long) approx 5mm Right Upper x : T009 x54 Turnbuckle 4 T009 T009 T009 5 Rear Suspension 6 Main Chassis T008 Mx8 Screw T008(x0) T008 Mx0 Screw T008 T008 T008 T008(x0) T008 T008(x8) x Assemble as many times as specified : Ture-to -scale diagram
7 Shock Absorber Front x Rear x T08 / T09. E-ring 8 Put a little oil T0067 T0068 9.9x.5 Shock Piston 4 T0069.8x.9 O-ring 8 T08 Put a little oil T0068 T0066 T0069 T0069(.8x.9) T0069(xmm) T0069(.8x.9) T0066 T09 T0068 T0069 T0069(.8x.9) T0069(xmm) T0069(.8x.9) T0067 T0069.xmm Plastic Washer 4 T08 T0066(Short) T09 T0067(Long) T0066 & T0067 8x O-ring 4 T08(Short) T09(Long) T04 5.8 Ball End 4 T07 T07 T07 5.8X6 Shock End Eyelet 4 T04 T04 8 Shock Absorber 00# T0066 / T0067 Put the oil for Front(Short) for Front(Short) for Rear(Long) for Rear(Long) F R x F R x x Assemble as many times as specified Assemble in the specified order F R Assemble front and rear sides the same way
9 Shock Absorber Front x T040 Short for adjusting the spring tension T040 Compress the spring and install T0066 Long T04 T0067 T040 mm adjuster ring T007(Short) 4 T04 T007(Long) Rear x 0 Front Suspension L R T0084 Short T008 T0084 M Nylon Nut T008 Mx5 Screw x Assemble as many times as specified L Assemble in the specified order R Assemble left and rear sides the same way 4
Rear Suspension T0084 Long T008 T0084 M Nylon Nut T008 Mx5 Screw L R Motor T0005 Motor 5 T008 Mx8 Screw T008 Mx5 Screw T008 T008 T04 T008 T008 x7x0.8 Washer T04 Mx Screw 4 5 L R Assemble left and rear sides the same way Assemble in the specified order
Steering Servo Select for your servo T000 T008 T008 T06 T008 T008 Steering Servo-H(4T) Steering Servo-S(T) T008(.6x8) T007(5T) T008 4 Sanwa servo SANWA T008 T005 X Steering Servo T000 4.8 Ball End(Short) T008 x7x0.8 Washer 4 T06 Ball stud - silvery T008 T000 Mx0 Screw T008 Mx8 Screw 4 T008 M.6x8 Screw T008 Mx8 Screw T005.5 Servo spacer 4 Radio T06 Receiver Box T0087 T008 Mx8 Screw Receiver T0087 Double-sided Tape Electronic speed controller T008 Mx8 Assemble in the specified order X Must be purchased separately 6
5 Battery If using loose battery cells Please put the battery panel conversely T0086 T0 T0086 T0 X Battery X Battery T0086 Small clip 6 Wheels Front x T0075 Rear x T0074 T0075(Sponge) T0074(Sponge) T0 Glue T0 Glue 4 After fitting wheels to tyres,apply instant glue as shown 7 x Assemble as many times as specified Assemble in the specified order X Must be purchased separately
7 Body Mounting 6mm 6mm T0076 8 Body Mounting T0086 Small clip 5 T00 T0084 M4 Flanged Nylon Nut 4 T0086 T008 T08 x T0086 + deg - deg T0084 x Assemble as many times as specified Drill holes with the specified diameter 6mm Cut off shaded portion 8
Exploded View T0084 T007 T0056 T008 T09 T008 T006 T008 T0075 T0005 T050 T07 T005 T0056 T008 T0084 T0066 T007 T0054 T09 T05 T008 T005 T006 T050 T0069 T0066 T0068 T08 T008 T008 T008 T008 T0087 T008 T008 T000 T007 T0075 T008 T06 T0066 T0066 T040 T008 T005 T0079 T008 T04 TS0 T0066 T055 T0078 T07 T0080 T004 T06 T00 T08 T007 T0060 T004 T07 T04 T004 T0080 T00 T0079 T004 T0079 T0044 T00 T0080 T0044 T008 T04 T004 T008 T0079 T04 T0005 T0084 T0040 T047 T05 T056 T05 T054 T057 T054 T056 T0078 T055 T008 T008 T0059 T0060 T009 T004 T009 T0056 T0084 T00 T0054 T0054 T0060 T009 T004 T004 T0056 T047 T0 T00 T0086 T008 T00 T0087 T06 T0086 T008 T008 T008 T008 T008 T008 T008 T0055 T008 T009 T05 T006 T004 T008 T0060 T00 T0084 T04 T007 T09 T0068 T09 T004 T0079 T009 T004 T0057 T0067 T007 T0067 T0084 T0 T05 T009 T0084 T005 T0057 T0074 T0069 T040 T07 T0055 T008 T008 T0087 T0059 T008 T0059 T008 T008 T008 T000 T008 T0086 T008 T008 T0 T008 T008 T008 T0067 T07 T008 9
BUGGY PARTS LIST T047 Front brace mount pcs pcs T050 T05 4pcs M.5x8 Screw pcs pcs Mx5 pcs Front chassis plate pcs Gear Differential Case 5T Diff Gear Cover pcs 5T Diff Gear pcs 4.8x.6 O-ring T05 T05 T054 T055 Rear Chassis Plate (Gear Diff) pcs Gear Differential Seal pcs 4T/8T Gear Set Gear Differential Outdrives pcs T056 T057 T0880 T0078 4.8x.6 Gear Diff O-Ring 4pcs Gear Diff Shaft pcs M.5x8 Screw 8pcs 0x5x4 Ball bearing-metal cover 6pcs T0079 T0080 T06 T00 5x0x4 Ball bearing-metal cover 6pcs x6x.5 Ball bearing-metal cover 4pcs pcs Receiver Box PCS Rear Wing-Buggy T0076 T09 TS0 T0005 PCS Gear Cover Button PCS Stock Buggy Body Lexan-Clear PCS 80T Spur Gear PCS 8T Idler Gear Aluminum PCS Gear Cover PCS T000 T00 T00 T00 Steering block-l PCS.x6x Plastic Washer Main Chassis plate PCS C-type holder L PCS C-type holder R PCS Steering block-r PCS Rear hub carriers-l PCS Rear hub carriers-r PCS
BUGGY PARTS LIST T004 T005 T004 T005 PCS PCS PCS Front Bulkhead-Rear Pin Mount Set Front upper suspension arm mount PCS Front lower arms PCS Rear lower arms PCS T008 T09 T00 T0 Rear shock tower PCS Rear brace mount PCS Front shock tower PCS Battery plate PCS T00 T004 T008 T006 Servo saver upper PCS Rear body mount PCS Servo saver lower PCS Servo saver - L PCS Steering Rack PCS Wing bracket PCS Battery column PCS Wing angie shim PCS Front bumper PCS Motor guard PCS T007 T008 T009 T000 Steering Steering Servo Steering Servo horn-f horn-h Servo horn-s PCS PCS PCS Servo plate PCS 4.8 Ball End-Long 6PCS 4.8 Ball End-Short PCS x0 Screw PCS T04 T0 T0 T004 Below Spring mount end PCS 5.8 Ball End PCS Front rim PCS Rear rim PCS Hexagonal x9.8 Pin T005 T006 T007 T008.0 Servo spacer PCS.5 Servo spacer PCS Motor plate PCS Front hinge pin brace PCS Slipper pad PCS
BUGGY PARTS LIST T04 T0040 T004 T004 PCS PCS 4.0 E-ring PCS Slipper hub PCS Slipper Spring PCS Top shaft spacer PCS PCS Servo Saver Shaft Assembly PCS T004 T0044 T009 T005 4.0 E-ring PCS x0 Screw PCS x9.8 Pin PCS Front wheel axle PCS Block Carrier PCS x7x0.8 Washer PCS x54 Turnbuckle PCS idler gear shaft PCS T005 T0054 T0055 T0056. E-ring. E-ring Gear 0T PCS x7.5 Hinge pin front outer x48 Hinge pin Rear inner PCS PCS x4.5 Hinge pin front inner PCS T0057 T05 T0059 T0060. E-ring x0.5 Hinge pin Rear outer Rear Drive Shaft Assembly Ball stud - long PCS PCS PCS Ball stud - short 5PCS T06 T07 T07 T08 x4.5 Front Shock Shaft PCS Ball stud - silvery PCS Shock End Eyelet 5.8X6 Upper Shock Bushing. E-ring T09 T0066 T0067 T0068 8x O-ring PCS 8x O-ring PCS x5 Rear Shock Shaft PCS Shock Absorber upper cover-plastic PCS Shock Absorber upper cover-plastic PCS. E-ring Front damper case PCS PCS Shock Absorber below cover-plastic top Spring mount end PCS Rear damper case PCS PCS Shock Absorber below cover-plastic top Spring mount end PCS Shock piston
BUGGY PARTS LIST T0069 T040 T007 T007.xmm Plastic Washer.8x.9 O-ring.5 Press washer mm adjuster ring mm adjuster ring mm adjuster ring 5mm adjuster ring Front spring PCS Rear spring PCS T007 T0074 T0075 T008 Diaphragm PCS PCS Rear buggy tires with foams PCS PCS Front ribbed buggy tires with foams x7x0.8 Washer 0PCS T008 T008 T0084 x5 Screw x8 Screw x Screw x5 Screw x5 Screw x Screw x0 Screw.6x8 Screw x8 Screw x0 Screw x5 Screw x8 Screw M4 Flanged Nylon Nut 6PCS M Nylon Nut 6PCS T0088 T0089 Front shock set buggy PCS Rear shock set buggy PCS T0085 T0086 T0087 TU06. E-ring 4 E-ring Small clip Antenna pipe PCS set cover Double-sided tape PCS Antenna pipe set PCS pcs Vented Slipper Hub
BUGGY PARTS LIST TU08 Tu09 Tu00 Tu0 Servo Saver-Aluminium C-Type-Holder 5 Degree C-Type-Holder 0 Degree Rear arm mount F/R Set Tu0 Tu0 Tu04 Tu05 4pcs Mx5 Screw Front arm mount Mx Set Rear arm mount -Ball 8pcs Servo mount pcs 4pcs 5.x8x0. Washer Hex mount 4pcs TU07 Tu09 Tu00 Tu0 set pcs Rear Brace Mount w/0g Weight Motor mount Hard Spring Set F&R Medium Spring Set F&R Tu0 Tu06 Tu07 TU040 pcs pcs pcs Soft Spring Set F&R Rear hub carriers Rear Hub Degree Carbon Front Shock Tower - Buggy pcs TU04 Tu048 TU054 TU076 Carbon Rear Shock Tower-Buggy pcs Aluminum Front Camber Link Mount pcs 4pcs mm Hex Hub-4mm pcs 86T Kevlar Gear TU077 pcs 80T Kevlar Gear
BUGGY PARTS LIST RCET0005 GEAR COVER...$.49 RCET000 MAIN CHASSIS PLATE...$ 7.99 RCET00 CASTOR BLOCKS L/R...$.99 RCET00 STEERING BLOCK...$.99 RCET00 REAR HUB CARRIERS...$.99 RCET004 FRONT BULKHEAD-REAR PIN MOUNT SET..$.99 RCET005 FRONT CAMBER LINK MOUNT...$.99 RCET008 REAR CHASSIS BRACE MOUNT...$.99 RCET00 SERVO SAVER SET...$.99 RCET004 STEERING RACK...$.99 RCET006 MOTOR GUARD...$ 4.99 RCET007 STEERING SERVO HORN F/H/S ()...$.49 RCET008 SERVO MOUNT...$.99 RCET009 4.8 BALL CUP - LONG (6)...$ 4.99 RCET000 4.8 BALL CUP - SHORT (-SERVO LINK)...$.99 RCET004 HEX WHEEL HUBS W/PINS (4)...$.99 RCET005 SERVO SPACERS...$.49 RCET006 MOTOR PLATE (RED)...$ 5.99 RCET007 FRONT HINGE PIN BRACE (RED)...$.99 RCET008 SLIPPER PAD...$ 4.99 RCET0040 SLIPPER SPRING...$.49 RCET004 T SHAFT SPACER...$.49 RCET004 FRONT WHEEL AXLE...$.99 RCET004 SERVO SAVER SHAFT ASSEMBLY...$ 0.99 RCET0044 SERVO SAVER HARDWARE...$ 5.99 RCET0045 x54 TURNBUCKLE()... $.49 RCET005 IDLER GEAR SHAFT...$.99 RCET005 T SHAFT...$.99 RCET0054 FRONT HINGE PIN OUTER ()...$.99 RCET0055 REAR HINGE PIN INNER ()...$.99 RCET0056 FRONT HINGE PIN INNER ()...$.99 RCET0057 REAR HINGE PIN OUTER ()...$.99 RCET0059 BALL STUD - LONG ()...$.99 RCET0060 BALL STUD - SHORT (5)...$.99 RCET0066 FRONT SHOCK BODY SET W/CAPS...$ 6.99 RCET0067 REAR SHOCK BODY SET W/CAPS...$ 6.99 RCET0068 SHOCK PISTON...$.49 RCET0069 SHOCK CARTRIDGE ASSEMBLY...$.49 RCET007 FRONT SPRING ()...$.99 RCET007 REAR SPRING ()...$.99 RCET007 SHOCK BLADDER (4)...$.99 RCET0074 REAR BUGGY TIRES WITH FOAMS()...$.99 RCET0075 FRONT RIBBED BUGGY TIRES WITH FOAMS()...$.99 RCET0076 STOCK BUGGY BODY LEXAN - CLEAR... $.99 RCET0076B STOCK BUGGY BODY LEXAN - BLUE... $ 4.99 RCET0076R STOCK BUGGY BODY LEXAN - RED... $ 4.99 RCET0078 0X5X4 OIL BEARING (6)...$ 6.99 RCET0079 5X0X4 OIL BEARING (6)...$ 4.99 RCET0080 BALL BEARING X6X.5 FLANGED (4)...$ 8.99 RCET008 WASHER x7x0.8 (0)...$.99 RCET008 SCREW SET A...$ 6.99 RCET008 SCREW SET B...$ 4.99 RCET0084 M/M4 NUT (6 EACH)...$.99 RCET0085 E-RING. & 4 E-RING (8 EACH)...$.99 RCET0086 BODY CLIP (8)...$.5 RCET0087 ANTENNA PIPE...$.99 RCET0088 FRONT SHOCK SET BUGGY()...$ 4.99 RCET0089 REAR SHOCK SET BUGGY()...$ 4.99 RCET009 TURNBUCKLE...$.49 RCET009 BALL STUD 4.8 X.5 - (5)...$ 5.99 RCET00 REAR WING - BUGGY... $.99 RCET004 FRONT A-ARMS ()...$ 9.99 RCET005 REAR A-ARMS ()...$ 9.99 RCET008 WING MOUNT & BATTERY POST SET... $ 7.49 RCET04 SPRING CUP/BALL END 5.8 ()...$.99 RCET07 UPPER SHOCK BUSHING...$.99 RCET09 80T SPUR GEAR...$.49 RCET09 FRONT SHOCK TOWER...$ 4.99 RCET00 REAR SHOCK TOWER...$ 4.99 RCET0 BATTERY SPACER - FOAM BATTERY BRACE... $.49 RCET0 FRONT RIM PCS WD BUGGY...$ 7.99 RCET0 REAR RIM PCS WD BUGGY...$ 9.99 RCET04 SLIPPER HUB ()...$ 4.99 RCET05 REAR DRIVE SHAFT ASSEMBLY ()...$ 9.99 RCET06 BALL STUD - SILVER ()...$.99 RCET07 SHOCK END EYELET 5.8X6 (4)...$.99 RCET08 x4.5 FRONT SHOCK SHAFT() -. E-RING(4)...$.49 RCET09 x5 REAR SHOCK SHAFT() -. E-RING(4)...$.49 RCET040 SHOCK ADJUSTER RING...$.99 RCET047 FRONT CHASSIS ASSEMBLY...$ 7.99 RCET050 GEAR DIFFERENTIAL CASE... $.99 RCET05 REAR CHASSIS PLATE (GEAR DIFF)...$ 5.99 RCET05 5T DIFF GEAR & COVER (GEAR DIFF)...$ 9.99 RCET05 GEAR DIFFERENTIAL SEAL()...$.49 RCET054 4/8 INTERNAL GEAR SET (GEAR DIFF)...$ 4.99 RCET055 GEAR DIFFERENTIAL OUTDRIVES()... $ 4.99 RCET056 4.8x.6 GEAR DIFF O-RING(4)... $.99 RCET057 GEAR DIFF SHAFT...$.99 RCET06 RECEIVER BOX... $.49 RCET0880 M.5X8 SCREW...$.90 RCETU00 GEAR DIFF CONVERSION KIT WD... $ 5.99 RCETU06 RCETU08 RCETU09 RCETU00 RCETU0 RCETU0 RCETU0 RCETU04 RCETU05 RCETU07 RCETU09 RCETU00 VENTED SLIPPER HUB...$ ALUMINUM SERVO SAVER WD... $ ALUMINUM CASTOR BLOCKS 5 DEGREE...$ ALUMINUM CASTOR BLOCKS 0 DEGREE... $ ALUMINUM REAR ARM MOUNTS()...$ FRONT BULKHEAD W/G WEIGHT... $ HINGE PIN PIVOT BALL(8)... $ ALUMINUM SERVO MOUNT... $ ALUMINUM MM HEX HUB...$ ALUMINUM REAR BRACE MOUNT W/0G WEIGHT...$ ALUMINUM FINNED MOTOR PLATE...$ HARD SPRING SET F&R(4)RTR...$ 9.99 9.99 4.99 4.99 9.99 8.99 5.99 4.99 4.99 9.99 4.99 5.99 RCETU0 MEDIUM SPRING SET F&R(4)RTR...$ 5.99 RCETU0 SOFT SPRING SET F&R(4)RTR... $ 5.99 RCETU06 RCETU07 RCETU09 ALUMINUM REAR HUB CARRIERS 0D... $ ALUMINUM REAR HUB CARRIERS D...$ CARBON FIBER REAR CHASSIS PLATE (BALL DIFF)...$ 4.99 4.99 4.99 RCETU040 RCETU04 RCETU048 RCETU054 RCETU076 CARBON FIBER BUGGY FRONT SHOCK TOWER...$ CARBON FIBER BUGGY REAR SHOCK TOWER...$ ALUMINUM FRONT CAMBER LINK MOUNT...$ MM HEX HUB - 4MM OFFSET...$ 86T KEVLAR GEAR...$ 4.99 9.99 4.99 4.99 6.99 RCETU077 80T KEVLAR SPUR GEAR... $ 6.99 RCETS0 8T IDLER GEAR ALUMINUM...$ 9.99 RCESGSL000 000KV SENSORLESS BL 540 MOTOR...$ 49.99 RCESGS6 6 KG METAL GEAR SERVO.8-8OZ... $ 4.99 RCETG05C PLASTIC SHOCK CAPS(4)... $.99 RCETSTBF PREMOUNTED FRONT TIRES & WHEELS WD BUGGY... $ 6.99 RCETSTBR PREMOUNTED REAR TIRES & WHEELS WD BUGGY... $ 9.99
Driver Track / City B uggy - Setup Sheet Event Date / / Conditions Smooth Bumpy Low traction Med traction High traction Sandy Soft dirt Grass Hard soil Clay Front Suspension Shock Mounting&Camber link Front Shocks Spring(color) Caster Black # Washers Camber 5 0 Wet Dry Dusty Other mm Toe-in (+)/Out (-) Bump Steep Spacer mm mm Oil Piston # wt # Washers mm Ride height Rear Suspension Shock Mounting&Camber link Wheelbase Long Medium Short Camber Normal 4 Aluminum(Opt) # Washers mm Rear Shocks mm mm Spring(color) Black Oil Piston # wt 4 Ride height Diff Front Tires&Wheels Front Tires&Wheels Brand Oil wt Front Tires Inserts Wheels Front Tires Inserts Wheels Batteries Motor Other Servo Esc Batteries Motor Pinion/Spur / Wing Wing Angle 4 0 Comments Notes