Installation manual. Pole-mount Deployment System

Installation manual Pole-mount Deployment System

974-80207001/2.0 Pole-mount Deployment System Installation Manual

Document revisions Version Date Written by Checked by Approved by 1.0 Aug 25, 2011 BC MA BC 1.1 Jul 11, 2012 BC SC BC 1.2 Aug 13, 2013 BC BC BC 1.3 Feb 07, 2013 BC BC BC 2.0 April 26, 2016 SC BC BC About this document The information contained in this document is subject to change without prior notice. Kongsberg Mesotech Ltd. shall not be liable for errors contained herein, or for incidental or consequential damages in connection with the furnishing, performance, or use of this document. 2016 Kongsberg Mesotech Ltd. All rights reserved. No part of this work covered by the copyright hereon may be reproduced or otherwise copied without prior permission from Kongsberg Mesotech Ltd. Kongsberg Mesotech Ltd. 1598 Kebet Way Telephone: +1 604 464 8144 Port Coquitlam, BC Telefax: +1 604 941 5423 V3C 5M5 Canada www.kongsberg-mesotech.com km.sales.vancouver@kongsberg.com

2015 - Kongsberg Mesotech Ltd. Table of contents 1 INTRODUCTION... 1 1.1 General... 1 1.2 System Description... 1 2 INSTALLATION INSTRUCTIONS... 2 2.1 Installation Requirements... 2 2.2 Unpacking... 2 2.3 Preliminary assembly steps... 4 2.4 Pole-mount Assembly... 8 2.5 Deployment... 10 3 REPACKAGING THE POLE-MOUNT KIT... 14 4 PARTS LIST... 17 5 DRAWINGS... 21 974-80207001/2.0 I

Pole-mount Deployment System - Installation Manual Document history Version 1.0 First Release Version 1.1 Update reflecting revisions of some pole-mount components. Version 1.2 Changed packing picture to reflect improved packing arrangement Version 1.3 Minor revisions to installation drawing Version 2.0 Update reflects revisions to a number of pole-mount components & packaging. II 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. 1 INTRODUCTION 1.1 General This is the instruction manual for the Pole-mount Deployment Kit designed for use with the Kongsberg Mesotech Sonar Heads. The purpose of the manual is to present the information needed to assemble, deploy and maintain the Pole-mount hardware. The tools required to: install, remove or replace any assemblies and parts are included in the kit. Each mechanical assembly is described and illustrated. The manual also includes procedures for disassembly and reassembly of the replaceable items. This manual does not give a detailed description of the peripheral devices. For information about these items, refer to the applicable manufacturer s documentation. 1.2 System Description The Pole-mount Deployment System is designed to assist in the deployment of a profiling system from a survey vessel of opportunity. The Sonar Head can be deployed with or without the rotator option and the mounting flange has been designed to accommodate both options. The pole mount kit components are supplied in a hard case for easy storage and transportation while the mast sections are supplied in a carry bag. NOTE: The mast length is approximately 135 inches (3.40 m) when all three sections are installed. Additional mast sections P/N 355-03060000 can be purchased if longer masts are required. NOTE: The sonar head mounting brackets are sold separately because they differ in size depending on the head that is used. NOTE: The protection cage assembly from the KML tripod can be attached to the pole mount. The cage P/N 806-00350000 can be purchased as an option if the user does not have a KML-supplied tripod. 974-80207001/2.0 1

Pole-mount Deployment System - Installation Manual 2 INSTALLATION INSTRUCTIONS Assembly of the Pole mount deployment system should be done near or on the vessel that will be used to deploy the Sonar Head. All the tools required to assemble the Pole-mount Deployment System are included in the shipping case. This document provides assembly instructions including some images to illustrate some of the steps required for assembly and deployment. The assembly instructions should be used in conjunction with the parts information and assembly drawings to minimize the potential for errors. NOTE: We recommend a review of the assembly drawings and parts list included at the end of this document prior to starting the assembly process. Assembly of the pole mount deployment system requires between 15-45 minutes, from unpacking the case to complete assembly. Two persons are required for installation and deployment. WARNING: Marine grade grease or anti-seize compound must be applied to all fasteners during assembly, particularly to the threads of the mast sections. 2.1 Installation Requirements 2.2 Unpacking Mounting Location of the Sonar Head The location on the pole mounted profiling system should be at the front of the survey vessel to minimize the turbulence around the sonar transducer. Sonar Head Cage Installation When the protection cage is used for deployment the sonar head must be installed in the deployment cage before attaching the cage to the pole mount deployment system. The pole mount deployment kit is packed in both a rigid shipping case and duffle bag. All the hardware required for assembling the pole mount deployment kit is contained in both these containers. 2 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. To start the assembly process, unpack the kit as shown in the picture below: The contents viewed from the top layer. The contents viewed from the middle layer. The contents viewed from the bottom layer. 974-80207001/2.0 3

Pole-mount Deployment System - Installation Manual 2.3 Preliminary assembly steps The pole mount deployment system is partially disassembled to facilitate packing in the shipping case. In preparation for the pole mount installation some preliminary assembly is required for some of the components of the pole mount deployment kit. WARNING: Marine grade grease or anti-seize compound must be applied to all fasteners during assembly, particularly to the threads of the mast sections. 2.3.1 Hull Mount Bracket Assembly Install the Turnbuckle assembly to the Hull Mount Plate (if not already installed) Install the Hull Mount Plate to the Hull Mount Bracket (if not already installed) Install the Hull Mount Clamp to the Hull Mount Bracket (if not already installed. 4 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. NOTE: Do not attach the loose end of the turnbuckle assembly to the Hull Mount Bracket at this time. This part will be assembled after the pole mount assembly is deployed and the Hull Mount Bracket is attached to the boat gunnel. 2.3.2 Preliminary Mast Assembly Position the Mast Clamp on the Hull Mount Plate and secure them together shown in the following picture using the supplied Pivot Bolt. Use the supplied hardware to secure the ends of the two curved mounting slots. 974-80207001/2.0 5

Pole-mount Deployment System - Installation Manual Slide the Top Mast Section through the Mast Clamp. Install the Stop collar. Install the GPS bracket on the top side of the Top Mast Section and secure with the provided fasteners. 6 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. Top Mast Section Stop Collar GPS Bracket 2.3.3 Sonar Cage Assembly (if cage is used for deployment) NOTE: Install the sonar head in the deployment cage and then proceed with the next step. 974-80207001/2.0 7

Pole-mount Deployment System - Installation Manual Sonar Cage secured using the supplied U-bolts and nuts. Cage & Sonar Head Mounted to Pole Flange. 2.4 Pole-mount Assembly 2.4.1 Cable Installation NOTE: The dry-mate cable connector must be inserted through each mast section before assembling the pole. Run the sonar cable through the GPS Bracket and the Top Mast Section. 8 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. Run the sonar cable through the Middle Mast Section(s). Run the sonar cable through the Bottom Mast Section and bring the cable out through the side wall hole. Connect the cable connector to the Sonar Head. 2.4.2 Pole Assembly NOTE: Take precautions to ensure the cable is not damaged during installation and deployment. Refer to the cable specifications for minimum bend radius, rated peak tension load and other mechanical information. Assemble the Top and Middle Mast Sections and secure them with the supplied set screw(s). Assemble the Middle and Bottom Mast Sections and secure them with the supplied set screw. 974-80207001/2.0 9

Pole-mount Deployment System - Installation Manual Insert the Sonar Cage Flange and secure using the supplied fasteners. Depending on the deployment configuration attach the Sonar Cage Stand, or the Rotator or the Sonar head to the Sonar Cage Flange using the appropriate hardware. 2.5 Deployment 2.5.1 Pole deployment Slide the Mast Clamp assembly on the pole assembly down to the Sonar Cage Assembly location on the Bottom Mast Section. 10 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. Lift the Pole-mount Assembly and position the Hull Mount Bracket on the ship s gunnel. Secure the hull mount bracket using the supplied C clamps or bolts, as applicable. For a permanent installation it is recommended to drill mounting holes in the Hull Mount Bracket for bolting to the vessel or operational platform. Pivot the pole assembly and lower the sonar as necessary. CAUTION: Pivot the mast horizontal, or retract the mast until the sonar head is out of the water, while in transit or moving. Always attach a safety line to the Pole-mount Deployment System and tie off to a secure point on the vessel or operational platform. NOTE: Use the safety through holes and the safety bolt provided in the tool kit to limit the pole travel to the desired location. Attach the loose end of the turnbuckle to the Hull Mount Bracket using the Spring clip (as illustrated). 974-80207001/2.0 11

Pole-mount Deployment System - Installation Manual Spring Clip used to secure Turnbuckle 2.5.2 Pole mount alignment If pitch adjustment is required loosen the screws attaching the Mast Clamp to the Hull Mount Plate and move two opposing screws to the center location to allow pitching in the right direction. Pivot the pole to compensate for any pitch and tighten the Cam lock to secure the Mast Clamp. 12 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. Adjust the turnbuckle to pivot the pole to compensate for any roll. Rotate the pole to align the cage to the heading of the boat then tighten the Mast Clamp bolts to secure the pole at the desired location and orientation. Install the GPS unit on the GPS bracket and re-orientate the bracket if necessary. Tighten the GPS Bracket bolts to secure the bracket in the desired orientation. Measure & record offsets between GPS and the sonar head s transducer face. The Deployment unit should now be ready for use. 974-80207001/2.0 13

Pole-mount Deployment System - Installation Manual 3 REPACKAGING THE POLE-MOUNT KIT The pole mount deployment kit must be partially disassembled after being used so it can fit into the shipping case and duffle bag. All the fasteners should be loosely attached to the corresponding mounting locations after disassembly to make it easier to locate the appropriate fasteners at the next deployment. To repackage all components in the case place them as shown in the following pictures: The contents of the Cardboard Box. The contents viewed from the bottom layer. 14 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. The contents viewed from the middle layer. The contents viewed from the top layer. 974-80207001/2.0 15

Pole-mount Deployment System - Installation Manual The complete repackaged System. 3.1.1.1 Pole mount packing list hard shell equipment case Ref. Part Number Description Qty - 437-00290000 Pole Mount Clamp assembly 1-437-00160000 Stop Collar 1-437-00180000 Hull mount bracket assembly 1-437-00190000 Mast Clamp Assembly 1-355-03100000 Sonar bottom flange 1-171-01067702 U-Bolt Set 4-422-43210000 Pole Mount tool kit case with C-Clamps (x2), and Wrench (15/16-inch) 1 3.1.1.2 Pole mount packing list Blue Canvas bag Ref. Part Number Description Qty - 355-03050000 Mast section top 1-355-03060000 Mast section middle 1-355-03070000 Mast section bottom 1-355-03120000 Sonar Cage Stand 1 16 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. 4 PARTS LIST The following parts are included in the Pole-mount Deployment kit P/N 974-80200000: KML P/N Description QTY Drawing # Item # 199 01001006 Shipping case 1 199 01001007 Custom bag for Poles 1 422 43210000 Spares & Tool Kit 1 422 43220000 Pole Mount Deployment Accessories Kit 1 437 00260000 GPS Box Mounting Flange 1 437 00280000 Sonar Cage Stand Assy. 1 437 00290000 Pole Mount Clamp Assy. 1 438 14020000 M3/Single Beam Pole Mount Assy. 1 The following parts are included in the M3/Single Beam Pole Mount assembly P/N 438-14020000: KML P/N Description QTY Drawing # Item # 159 04000614 Pole Thread Alignment Tool 1 171 01060609 3/8 16 X 3/8 Hex Socket Set Screw 316 SS 2 974 80201000 A12 171 01061208 3/8 16 X 3/4 Socket Head Cap Screw 316 SS 2 974 80201000 A9 171 01066402 3/8 16 X 4 Socket Head Cap Screw 316 SS 1 974 80201000 A10 171 02060102 Washer Flat 3/8 0.391=ID 0.875 OD 316 SS 2 974 80201000 A6 355 03050000 Mast Section Top 1 974 80201000 A3 355 03060000 Mast Section Middle 1 974 80201000 A4 355 03070000 Mast Section Bottom 1 974 80201000 A5 355 03100000 Sonar Cage Flange 1 974 80201000 A8 437 00160000 Stop Collar 1 974 80201000 A7 437 00180000 Hull Mount Bracket Assy. 1 974 80201000 A2 437 00190000 Mast Clamp Assy. 1 974 80201000 A1 974-80207001/2.0 17

Pole-mount Deployment System - Installation Manual The following parts are included in the Pole Mount Clamp assembly P/N 437-00290000: KML P/N Description QTY Drawing # Item # 171 01061208 3/8 16 X 3/4 Socket Head Cap Screw 316 SS 4 437 00091000 14 171 02060102 Washer Flat 3/8 0.391=ID 0.875 OD 316 SS 4 437 00091000 9 171 02060402 Washer Split Lock 3/8 316 SS 4 437 00091000 15 355 03000000 Pole Mount Clamp 1 437 00091000 3 The following parts are included in the Sonar Cage Stand assembly P/N 437-00280000: KML P/N Description QTY Drawing # Item # 171 01041008 1/4 20 X 5/8 Socket Head Cap Screw 316 SS 4 974 80201000 16 171 01067702 U Bolt Set 1/4 20 x 9/16 W x 1.5 L 304 SS 4 974 80201000 5 171 02040103 Washer Flat 1/4 5/8 OD 316 SS 4 974 80201000 17 355 03120000 Sonar Cage Stand 1 974 80201000 1 The following parts are included in the GPS Box Mounting Flange assembly P/N 437-00260000: KML P/N Description QTY Drawing # Item # 171 01066402 3/8 16 X 4 Socket Head Cap Screw 316 SS 1 437 00261000 2 355 03640000 M3 Pole Mount Deployment Bracket 1 437 00261000 1 18 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. The following parts are included in the Pole Mount Deployment Accessories Kit P/N 422-43220000: KML P/N Description QTY Drawing # Item # 171 01041008 1/4 20 X 5/8 Socket Head Cap Screw 316 SS 2 974 80201000 16 171 01061208 3/8 16 X 3/4 Socket Head Cap Screw 316 SS 2 437 00091000 11 171 01067702 U Bolt Set 1/4 20 x 9/16 W x 1.5 L 304 SS 1 974 80201000 5 171 02040103 Washer Flat 1/4 5/8 OD 316 SS 2 974 80201000 17 171 02060102 Washer Flat 3/8 0.391=ID 0.875 OD 316 SS 2 437 00091000 10 171 02060402 Washer Split Lock 3/8 316 SS 2 437 00091000 9 974-80207001/2.0 19

Pole-mount Deployment System - Installation Manual The following parts are included in the Tools & Spares kit P/N 422-43210000: KML P/N Description QTY 159 0072 Anti seize lubricant 1/4 oz tube 1 159 03000502 Wrench Combination 9/16 1 159 03000503 Wrench Combination 15/16 1 159 04000502 Allen Key 3/16 Long 1 159 04000503 Allen Key ¼ Long 1 159 04000504 Allen Key 5/16 Long 1 159 04000506 Allen Key 3/8 Long 1 159 04000604 Wrench Combination 1/2 1 159 04000612 C Clamp Malleable 8 x 4 2 171 01060609 3/8 16 X 3/8 Hex Socket Set Screw 316 SS 2 171 01060811 3/8 16 X 1/2 Screw Hex Skt Shoulder 316 SS 1 171 01062007 3/8 16 X 1 1/4 Hex Socket Cap 316 SS 2 171 01066402 3/8 16 X 4 Socket Head Cap Screw 316 SS 1 171 02060102 Washer Flat, 3/8" 316 SS 2 171 05060901 3/8 16 Nut Hex Nylok 316 SS 3 199 01001008 Case Organizer Sortmaster JR. 1 355 03010000 Hull Mount Spacer 1 NOTE: To order any replacement parts please use the corresponding Kongsberg Mesotech Ltd. part number (KML P/N) from the parts list above. 20 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. 5 DRAWINGS The assembly drawings are included to assist with the installation and maintenance of the pole mount. These documents were the most current at the time this manual was printed. Drawings should be replaced with the most recent revision as they become available. Contact your local Kongsberg Mesotech Ltd. representative to ensure your drawings are up to date. Document List Drawing Number Description 974-80201000 Pole Mount Deployment Assembly Drawing 437-00091000 Hull mount Bracket Assembly Drawing (Sheet 1 of 2) 437-00091000 Hull mount Bracket Assembly Drawing (Sheet 2 of 2) 355-03108000 Sonar Cage Flange Drawing 437-00191000 Mast Clamp Assembly Drawing 437-00261000 GPS Bracket Assembly Drawing 974-80207001/2.0 21

Pole-mount Deployment System - Installation Manual 22 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. 974-80207001/2.0 23

Pole-mount Deployment System - Installation Manual 24 974-80207001/2.0

2015 - Kongsberg Mesotech Ltd. 974-80207001/2.0 25

Pole-mount Deployment System - Installation Manual 26 974-80207001/2.0

<This page is left intentionally blank>

2013 Kongsberg Maritime