Stainless Steel Outboard Motor Brackets - Installation and Operating Instructions Models T10054 and T10055
|
|
- Percival Cunningham
- 6 years ago
- Views:
Transcription
1 USER MANUAL OUTBOARD MOTOR BRACKETS Stainless Steel Outboard Motor Brackets - Installation and Operating Instructions Models T10054 and T10055 CAUTION Do not exceed the bracket s HP or weight limits. Read instructions completely before starting assembly. Motor bracket must remain in the UP position throughout installation. DO NOT operate motor bracket unless motor is installed on bracket. This bracket is under spring tension. Exercise caution when installing and operating. BRACKET ANGLE ADJUSTMENT INSTRUCTIONS Refer to Figure 1 Measure the exact angle and direction of the transom on your boat. Determine if your motor can be adjusted so the cavitation plate is parallel to the waterline. If this is possible then skip adjustment instructions (Figs. 2-7) and go to the Installation Instructions on Page 3. If your motor cannot be trimmed properly, follow the section below for the type of transom you have: "POSITIVE ANGLE" or "NEGATIVE ANGLE." FOR NEGATIVE ANGLED TRANSOMS Refer to Figures 2, 3 & 4 Now that the angle and direction of your transom have been determined, choose the adjustment hole on our bracket that will best compensate for the angle of your transom. NOTE: Each adjustment hole represents a 7 increment. Refer to Figures 3 & 4 Adjust your bracket by removing mounting board (A). This is done by unscrewing four nuts (B) and lock washers (C). Pull safety lock out and rotate it to the unlocked position. Unscrew locknut (D) and pull out pivot bolt (E). Now replace pivot bolt (E) through the desired adjustment hole in the top flange bracket (I). Reassemble unit by sliding bolt through washer (F), lower lever arm hole, spacer (G), lock bar arm hole spacer (H), lock bar arm hole, spacer (G), lower lever arm hole, washer (F) and through the other desired adjustment hole.
2 Secure bolt in position with nut (D); do not over-tighten nut so as to bind movement of bracket. NOTE: Bolt must protrude through the top of the nut to insure locking. Pull safety lock out and rotate it back into the locked position. Replace the mounting board (A) on your bracket with washers (C) and nuts (B). Secure in position. Refer to installation instructions. FOR POSITIVE ANGLED TRANSOMS Refer to Figures 5, 6 & 7 Begin the adjustment of your bracket by removing mounting board (A). This is done by unscrewing four nuts (B) and lock washers (C). Pull safety lock out and rotate it to the unlocked position. Unscrew locknut (D) and pull out pivot bolt (E). Unscrew locknut (L) and pull out pivot bolt (J). Now flip the top flange brackets over and put the left bracket on the right side and; the right on the left side as illustrated in Figure 5. Reattach the Flange brackets to the bracket by sliding pivot bolt (E) through the lower hole in the flange bracket, (I), washer (F) lower lever arm hole, spacer (G), lock bar arm hole, spacer (H), lock bar arm hole, spacer (G) lower lever arm hole, washer (F) and through the other lower hole in the flange bracket. Secure bolt in position with nut (D); DO NOT over tighten nut so as to bind the operation of the bracket. NOTE: Bolt must protrude through the top of the nut to insure locking. Use the measured angle of your transom to choose the proper adjustment hole in your bracket that will best compensate for this angle. NOTE: Each adjustment hole represents a 7 increment (Refer to Figure 7). Replace pivot bolt (J) through the desired adjustment hole in the top Flange bracket (I). Reassemble unit by sliding bolt through washer (F), upper lever arm hole, spacer (K), upper lever arm hole, washer (F) and through other desired adjustment hole in top flange bracket. Secure bolt in position with nut (L). Now replace the mounting board (A) as pictured in Figure 5 on your bracket with washers (C) and nuts (B). Secure in position. Move safety lock back into locked position. Refer to Installation Instructions.
3 INSTALLATION INSTRUCTIONS Refer to Figure 8 Measure the distance on your outboard motor between the cavitation plate and the upper inside edge of the mounting clamp. Subtract 2" from this length. Then add the total travel distance of your model outboard motor bracket, from the table in Figure 8, to the distance measured on your motor. (Measure clamp to cavitation plate) add (bracket s vertical travel) subtract 2 =
4 Refer to Figure 9 Mark this total length on a stick and tape it so that the top of the stick is flush with the top of the mounting board of the motor bracket. Choose the most appropriate side of your transom for installing the bracket, position your bracket so it will not interfere with the turning operation of your primary motor or rudder. Refer to Figure I0 Powerboat Installation: Position the outboard motor bracket with the stick taped on and place the installation flanges on your transom. Position the bracket so the bottom of the stick is one inch above the boat s bottom at the centerline of the outboard motor bracket. Refer to Figure 11 Sailboat Installation: Position the outboard motor bracket with the stick taped on and place the installation flanges on your transom. Position the bracket so the bottom of the stick is even with the boat s waterline.
5 Refer to Figure 12 After the bracket has been properly positioned mark the four corner hole locations using the bracket as a template on the boat s transom. Drill the four marked holes with a 3/8" drill bit, making sure to hold the drill at right angles to the transom when drilling. Refer to Figure 13 If your transom is less than 2" thick, it is recommended that a backing plate be made and installed on the inside of the transom for rigidity. Attach your motor bracket to the transom by coating the inside surfaces of the mounting flanges and backing plate with a marine adhesive/ sealant compound and then squeeze a small amount into each bolt hole on both sides of the transom. Secure the bracket to the transom with the supplied hardware as illustrated in Figure 13. The bracket is now ready for motor attachment. OPERATING INSTRUCTIONS To Lower Motor: Disengage safety lock by pulling it out and rotating it away from the locknut. Pull lever handle toward the boat to disengage locking pin. Grasp motor and SLOWLY lower it to desired height. Release lever handle; locking pin will snap forward into slot. To Raise Motor: Pull lever handle toward the boat to disengage locking pin. Grasp motor and lift up to desired height. Release lever handle; locking pin will snap forward into slot. Engage safety lock by pulling it out and rotating it so it snaps over the pivot bolt. CAUTION! IMPORTANT GUIDELINES: 1. Install motor bracket only in "up" position with safety lock in "locked" position. 2. Always remove your motor from the bracket when trailering. Failure to do so could result in damage to boat, motor and bracket. 3. Do not exceed the stated H.P. rating and weight rating of this bracket. 4. Use a safety cable when operating your motor. 5. Operate motor at low speed. 6. Avoid turning motor at full throttle, refrain from sharp turns. 7. Operate motor in lowest position possible for best performance. 8. Always raise and tilt motor when not in use. 9. Keep pivoting bolts greased to insure smooth operation.
6 SPECIAL NOTE: The bracket springs counter most of the motor s weight; however, a slight push or lift may be needed. If lowering the bracket is too difficult due to the use of a light weight motor, it may then be desirable to decrease some spring tension. This is accomplished by cutting one but not more than three springs as illustrated in Figure 14. Cut one spring at a time and test operation before cutting another. Make sure to cut the spring s leg as close to the coil as illustrated. PARTS LIST ITEM DESCRIPTION QTY. A Mounting Board 1 B 5/16 SS Carriage Bolt 4 C SS Pronged Washer 2 D 5/16 SS Lock Nut 4 E Short Angle Right 1 F Short Angle Left 1 G 3/8 SS Hex Bolt 6 H PP Washer 8 I Plastic Spacer Long 3 J Plastic Spacer Short 2 K Plastic Spacer Medium 2 L 3/8 SS Locknut 6 M Top Plate Welded 1 N Bottom Plate Welded 1 O Torsion Spring 4-8 P Long Angle Left 1 Q Long Angle Right 1 R 5/16x4-1/2 1 S Double Torsion Spring 1 T SS-Lock Washer 1 U Safety Latch 1 V Hardware Pack 1
7 LIMITED WARRANTY This limited warranty is provided by TRAC Outdoor Products Co (TRAC) to the original consumer purchaser (purchaser) of the new (not refurbished) TRAC Outboard Motor Bracket. This limited warranty is not transferable to any other party. TRAC will at it option repair or replace any part of the TRAC Outboard Motor Bracket which may be found by TRAC to be defective within two (2) years of original purchase. TRAC does not pay for the shipping cost from original purchaser to TRAC. You will have to ship the items to us for repair or replacement. For warranty repair or replacement, the purchaser will provide dated proof of purchase (sales receipt) and promptly notify TRAC of the request for warranty action. The purchaser will notify TRAC by at or by calling for warranty action. Purchasers will be provided a Return Goods Authorization (RGA) to include with return for warranty work which will be shipped at the purchaser s expense to the address provided. The purchaser must use reasonable care in maintenance and operation of the product in accordance with this manual. Failure to follow the instructions in the manual will void the warranty. This warranty covers defects in material or workmanship of the TRAC Outboard Motor Bracket only. This warranty does not cover failure that results from misuse, improper installation, accident, abuse, neglect, modification, or improper maintenance. There are no other express or implied warranties. Any damage to watercraft or trailer resulting from proper or improper use of this TRAC Outboard Motor Bracket is not covered under this warranty. Costs of installation or repair by service centers or marine repair facilities are not covered by this warranty. This is the exclusive remedy and any liability for any and all incidental or consequential damages or expenses whatsoever is excluded. Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential damages, the above limitations may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. TRAC Outdoor Products Co 6039 Dana Way Antioch, TN info@trac-outdoor.com (615)
INSTALLATION AND OPERATING INSTRUCTIONS
Auxiliary Outboard Motor Bracket for the following products: 55-0010, 55-0012, 55-0020A, 55-0021, 55-0022 INSTALLATION AND OPERATING INSTRUCTIONS 55-0010 55-0012 & 55-0021 55-0020A REV. 12/15 AUXILIARY
More informationINSTALLATION AND OPERATING INSTRUCTIONS. First READ THIS MANUAL. If you still need help, call us from 9 am to 4 pm (central time) Monday Friday.
INSTALLATION AND OPERATING INSTRUCTIONS LINE HAULER T10250 TRAC Line Hauler / Pot Puller If you have any questions or difficulty installing this product, TRAC is here to help! First READ THIS MANUAL. If
More informationSWIM PLATFORM BRACKET
55-0030 SWIM PLATFORM BRACKET FOR LIGHT WEIGHT 4 STROKE ENGINES UP TO 20 HP AND 195 LBS. INSTRUCTION MANUAL REV. 12/15 4-Stroke Auxiliary Outboard Motor Bracket Mounting Instructions for Proper Location
More informationMODEL AL ADJUSTABLE ALUMINUM BRACKET DESIGNED FOR AUXILIARY MOTORS UP TO 15HP INSTRUCTION MANUAL
MODEL 55-0407AL ADJUSTABLE ALUMINUM BRACKET DESIGNED FOR AUXILIARY MOTORS UP TO 15HP INSTRUCTION MANUAL This is the side that faces the transom Ver cal travel : 10 inches [25.4 cm] Setback up: 8 3/4 inches
More informationMODEL FIXED MOTOR BRACKET
MODEL 55-0027 FIXED MOTOR BRACKET INSTALLATION MANUAL REV 12/15 CUSTOMER MUST RECEIVE THIS MANUAL AFTER INSTALLATION INSTALLATION PROCEDURES Congratulations, you have just purchased one of the finest outboard
More informationIf you have any questions or difficulty installing this product, TRAC is here to help! If you still need help, call us from 8 am to 4 pm
For Trailer Winch Models: T10124-C Day Runner T10128-C Lite Cruiser (cable) T10129-S Lite Cruiser (strap) If you have any questions or difficulty installing this product, TRAC is here to help! First READ
More informationINSTALLATION INSTRUCTIONS BASE RAIL MOUNTING KIT GM COMPOSITE BED 58208
INSTALLATION INSTRUCTIONS BASE RAIL MOUNTING KIT GM COMPOSITE BED 58208 DEALER/INSTALLER: (1) Provide this Manual to end user. (2) Physically demonstrate procedures in this Manual to end user. (3) Have
More informationINSTALLATION INSTRUCTIONS FOR TRANSOM ADAPTOR. FOR MOTORS UP TO 20 HP Fits Panther Brackets , , ,
INSTALLATION INSTRUCTIONS FOR 55-0023 TRANSOM ADAPTOR. FOR MOTORS UP TO 20 HP Fits Panther Brackets 55-0010, 55-0012, 55-0021, 55-0022 REV. 12/15 The TRANSOM ADAPTER allows the user to remove the outboard
More informationINSTALLATION AND OPERATING INSTRUCTIONS
DUAL AND TRITON 2 AND 3 MOTOR SERIES Model 65-0110 Freshwater Model 65-1110 Saltwater 24 volt 110 lb. Thrust Model 65-0165 Freshwater Model 65-1165 Saltwater 24 volt 165 lb. Thrust INSTALLATION AND OPERATING
More informationREPLACING ROLTEC SPRING ARMS
REPLACING ROLTEC SPRING ARMS NOTICE TO INSTALLER: Even if familiar with hardware, read instructions prior to installation as improvements may be made without notice. Always handle components with care.
More informationELECTROSTEER MODEL A FRESHWATER MODEL A SALTWATER
ELECTROSTEER MODEL 55-0100A FRESHWATER MODEL 55-0101A SALTWATER INSTALLATION AND OPERATING INSTRUCTIONS CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER INSTALLATION Rev 01/13 P/N 99-55276 INTRODUCTION
More informationInstallation Instructions SRC Over-Size Tire Carrier Jeep Wrangler/Unlimited Part # 2743
NOTE: Carefully read instructions entirely before assembling/installing this product. Parts Included Qty Parts Included Qty Tire Carrier 1 8 x 70mm Hex Bolt 4 Brake Light Bracket 1 8mm Flat Washer 4 Tire
More informationMOUNTING RAILS ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
10/30/2017 PAGE 1 OF 6 Parts List ITEM QTY PART NUMBER DESCRIPTION 1 2 CM-16150-MR MOUNTING RAILS 2 2 CM-16150-FB.375" FRONT BRACKET 3 1 CM-16150-PSRB.375" PASSENGER SIDE REAR BRACKET 4 1 CM-16150-DSRB.375"
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab Diesel 2011 and newer Part Number: 75147-15 Chevy Silverado/GMC Sierra
More informationULTRA WEIGHT DISTRIBUTING HITCH SYSTEM INSTALLATION/OPERATION INSTRUCTIONS
ULTRA-FAB PRODUCTS, INC. 57985 St. Rd. 19 South, Elkhart, Indiana 46517 ULTRA WEIGHT DISTRIBUTING HITCH SYSTEM ULTRA WEIGHT DISTRIBUTING HITCH SYSTEM INSTALLATION/OPERATION INSTRUCTIONS ITEM # 1 EXPLODED
More informationOperating Instructions and Parts Manual AHR-50 Auto Rewind Hose Reel
Operating Instructions and Parts Manual AHR-50 Auto Rewind Hose Reel JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-426238 Ph.: 800-274-6848 Revision C 04/2017 www.jettools.com Copyright
More informationASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH
ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. (2) Physically demonstrate procedures in this Manual to end user. (3) Have end user
More informationInstallation Instructions
Installation Instructions Application Fits 2015+ Volkswagen Golf R X7332 & X7333 2 & 1.25 EcoHitch Stealth 200 lb. Tongue Weight/ 2,000 lb. Towing Weight HICKNESS LENGTH Torklift Central 315 Central Ave
More information(615) Note: At this time, we provide Phone Support in English only.
INSTALLATION AND OPERATING INSTRUCTIONS TRAILER WINCHES For TRAILER WINCH Model: T10121-C Small Craft Every installation can be different. If you have any questions or difficulty installing this product,
More informationFOR ALL SINGLE MOTOR UNITS INSTALLATION AND OPERATING INSTRUCTIONS REV 12/15 89
FOR ALL SINGLE MOTOR UNITS INSTALLATION AND OPERATING INSTRUCTIONS REV 12/15 89 INTRODUCTION Congratulations, you have just purchased one of the most unique trolling motors available today. It is the Original
More informationInstallation Instructions
Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT 2011 & UP Ford Super Duty F-250/F-350/F-50 2011 & UP Part Number: 50073 WARNING: Under no circumstances do we recommend exceeding the towing
More informationInstallation Instructions
Installation Instructions Application Fits 2015 Volkswagen Golf Sportwagen X7315 & X7316 2 & 1.25 EcoHitch Stealth 200 lb. Tongue Weight/ 2,000 lb. Towing Weight L THICKNESS LENGTH Torklift Central 315
More informationWARNING OPERATING PRESSURES: READ INSTALLATION INSTRUCTIONS COMPLETELY BEFORE INSTALLING YOUR KIT
4190 www.riderite.com OPERATING PRESSURES: MINIMUM (UNLOADED) MAX (LOADED) 5 PSI 35 PSI READ INSTALLATION INSTRUCTIONS COMPLETELY BEFORE INSTALLING YOUR KIT INSTALLATION INSTRUCTIONS Congratulations your
More informationInstallation Instructions
Installation Instructions www.bestop.com - We re here to help! Visit our web site and click on Ask a Question INSTALLATION TIME SKILL LEVEL Automatic Retracting Running Board Vehicle Application Chevy
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 15/16, 10 mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING: Under
More information(615) Note: At this time, we provide Phone Support in English only.
OPERATING INSTRUCTIONS TRAILER WINCHES For ELECTRIC TRAILER WINCH Models: T10128-C Lite Cruiser (cable) T10129-S Lite Cruiser (strap) T10130-Csw Salt Water Series Lite Cruiser (cable) Every installation
More informationDodge Ram 1500, Quad/Reg. Cab, w/6.4ft. & 8ft. Bed, 2 & 4 WD. For updates see PRODUCT SUPPORT tab at
Assembly, Installation, Operation and Maintenance Instructions 2009-2016 Dodge Ram 1500, Quad/Reg. Cab, w/6.4ft. & 8ft. Bed, 2 & 4 WD. Part # 30665 Dealer / Installer: Provide a copy of these Instructions
More information11403 INSTALLATION INSTRUCTIONS
0 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0 MAKE: CHRYSLER MODEL: 00 STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED
More informationSafety Sentry Electronic Breakaway Switch
Safety Sentry Electronic Breakaway Switch P-616-WE 819-0454 Installation Instructions An Altra Industrial Motion Company Parts List Mounting hardware included with the Safety Sentry Breakaway Switch kit:
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**
60660 SUBKIT 7/8/0 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** DODGE 500 / 3500 SHORT AND LONG BED PAGE OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED
More informationInstallation Instructions
Installation Instructions Application Fits 2013-2014 BMW X5 X7265 2013-2014 BMW 500 lbs. Tongue Weight/5,000 lbs Weight Carrying X5 2 EcoHitch Invisi Torklift Central 315 Central Ave N Kent, WA 98032 253-854-1832
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 10mm, 18mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw 9465/9475 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING:
More informationAEROMOTIVE Part # & Mustang 5.0L Stealth Fuel System Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 18653 & 18654 86-93 Mustang 5.0L Stealth Fuel System Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures.
More informationInstallation Instructions **THIS RAIL MOUNTING KIT USES 11 BOLTS**
Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT FORD SUPER DUTY Part Numbers: 50074 WARNING:Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle
More informationInstallation Instructions
Installation Instructions Application Fits 2016 Honda HR-V X7322 & X7323 2 & 1.25 EcoHitch Stealth 200 lb. Tongue Weight/ 2,000 lb. Towing Weight Torklift Central 315 Central Ave N Kent, WA 98032 253-854-1832
More informationCOVER PAGE CUSTOM QUICK INSTALL MOUNTING KIT NOTE!
COVER PAGE NOTE! Prior to installing product, please visit one of our websites to assure your kit contains the most recent revision to installation instruction and verify vehicle application. www.reeseproduct.com
More information31015 INSTALLATION INSTRUCTIONS
0 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 00-CURRENT MAKE: DODGE RAM MODEL: 00 STYLE: TRUCK WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC
More informationInstallation Instructions
Installation Instructions Rock Crawler Roof Rack (Part # 76717) 07-Up Jeep Wrangler J/K 4Door For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton,
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350
6065 SUBKIT 7/7/0 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-50, F-50 PAGE OF WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR
More informationLevel One Electric Vehicle Charging Station Wall Mount Product Guide
Level One Electric Vehicle Charging Station Wall Mount Product Guide Model # WU-120 ShorePower Technologies 2351 NW York St. Portland, OR 98664 503-892-7345 info@shorepower.com www.shorepower.com 2 Table
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350
60647 SUBKIT 7/3/204 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350 PAGE OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE
More informationDODGE / RAM 1500 *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMENDED TOWING CAPACITY ***
6444 DODGE / RAM 500 6/8/207 OF 5 *** DO NOT EXCEED MANUFACTURER'S RECOMENDED TOWING CAPACITY *** ITEM QTY PART NUMBER 0 /2-3 x 2" 2 4 /2-3 x 3/4, GR8 3 4 CM-SP2 4 2 CM-SP6 5 4 HFN 23, GR8 6 2 CM-SP4 7
More informationPlease Do Not Return This Product To The Store!
TABLE TENNIS TABLE MODEL NOS. T8167 QUICKPLAY 1000 T8267 QUICKPLAY 1000 T8180 METRO OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each
More informationadvanced FLOW engineering Instruction Manual P/N: Make: BMW Model: 328d/dx (F30/F31) Year: Engine: L4-2.
advanced FLOW engineering Instruction Manual P/N: 46-20301 Make: BMW Model: 328d/dx (F30/F31) Year: 2014-2017 Engine: L4-2.0L (td) N47 Please read the entire instruction manual before proceeding. Ensure
More informationCHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT
85101 2000-2010 CHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT C8510-4 MAIN BOX KIT W/ HARDWARE 1) FRONT X MEMBER 1) REAR X MEMBER 2) TORSION BAR DROPS 1) LEFT BUMP STOP 1) RIGHT BUMP STOP 2) SWAY BAR
More informationHolley Accessory Drive Kit Part Number
Assembly Instructions Holley Accessory Drive Kit Part Number 20-133 Table of Contents Parts List:... 2 Passenger s Side Bracket Installation:... 3 A/C Compressor Installation:... 4 Idler & Tensioner Installation:...
More informationSPECIALTY TOP CO. STC. INSTALLATION INSTRUCTIONS TOYOTA FAST TRAC Z TOP Toyota FJ PART #222-31X 82 1/8" 82 1/8"
STC INSTALLATION INSTRUCTIONS TOYOTA FAST TRAC Z TOP Toyota FJ-40 1963-1983 PART #222-31X SPECIALTY TOP CO. Thank you for purchasing Specialty's Convertible Top for your Toyota. It has been designed for
More informationUser Instruction Manual
RAIL LOCK SPRING COMPRESSOR User Instruction Manual For Spring and Gas Piston Rifles and Pistols V1 03/16 Contents Parts of the Rail Lock compressor...3 Disassembling your rifle or pistol...4-6 Assembling
More information3/8" 5 35 ft/lbs. 10mm 42 ft/lbs. 1/2" 5 85 ft/lbs. 14mm 95 ft/lbs.
0-06 TP056,Rev. ASSEMBLY OPERATION REPLACEMENT PARTS Kia Rio BOLT TORQUE SPECIFICATIONS STANDARD BOLTS: METRIC BOLTS: Size Grade Torque Size Torque 5/6" 5 0 ft/lbs. 8mm ft/lbs. /8" 5 5 ft/lbs. 0mm 4 ft/lbs.
More informationV HUB INSTALLATION AND OPERATING INSTRUCTIONS
2008 Wood Court Plant City, FL 33563 USA Phone (813)752-3711 Fax (813)752-2818 http:\\www.sensenich.com Composite Airboat Propellers V HUB INSTALLATION AND OPERATING INSTRUCTIONS CAUTION: Failure to follow
More informationInstallation Instructions READ THOROUGHLY BEFORE BEGINNING Signature Series Rail Kit Dodge Ram Trucks-all, including Mega-cabs
INDEX Failure to follow all of these instructions may result in death or serious injury!. GUIDELINES FOR MATCHING TOW VEHICLE AND TRAILER. Pages -. DRILLED AND BOLTED INSTALLATION FIGURE. Page 4. NO-DRILL,
More informationAir and water reels. Models and Series B. Installation and maintenance guide DANGER
Installation and maintenance guide Air and water reels Models 83753 and 83754 Series B Date of issue June 2014 Form number 404665A Section E35 Page 83A DANGER Read manual prior to installation or use of
More informationMODEL MODEL S
MODEL 55-0502 MODEL 55-0503 S INSTALLATION AND OPERATING INSTRUCTIONS CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER INSTALLATION Rev 12/15 INTRODUCTION Congratulations, you have just purchased
More informationInstallation Instructions Limb Riser Kit JK, TJ, XJ Part#7611, 7612,7613
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts included Qty Windshield Bracket L+R Lower Bracket (JK+XJ) 2 Lower Bracket (TJ) L+R M8-1.0x30mm Hex head
More informationINSTALLATION INSTRUCTIONS MOUNTING KIT COMMERCIAL TRUCK FOR 34 OUTSIDE FRAME WIDTH ONLY. Front of vehicle
INSTALLATION INSTRUCTIONS MOUNTING KIT COMMERCIAL TRUCK FOR 34 OUTSIDE FRAME WIDTH ONLY DEALER/INSTALLER: (1) Provide this Manual to end user. END USER: (1) Save this Manual for future reference. (2) Pass
More informationAssembly Instructions. Holley Accessory Drive Kit Part Number
Assembly Instructions Holley Accessory Drive Kit Part Number 20-131 Table of Contents Parts List:... 2 Driver s Side Bracket Installation:... 3 Power Steering Pump Installation:... 4 Idler Pulley Installation
More informationUtility Jack Model Number: HD HD HD
Utility Jack Model Number: 74407 74407HD 74410 74410HD 74413 74413HD 74412 74415 70429 Rolled Acme Thread and Anti-Friction thrust Bearings High Strength Tubing This Instruction Sheet contains IMPORTANT
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 13mm Drill Bits: 1/4, some older models a 1/2 Other Tools: Drill, Saber Saw 5/8 Fasteners From Hitch Fastener Kit Installation Instructions GOOSENECK
More informationOWNER'S MANUAL. Please Do Not Return This Product To The Store!
TABLE TENNIS TABLE MODEL NO. T87 OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts may be shipped inside
More information11347 INSTALLATION INSTRUCTIONS
1147 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 01-PRESENT MAKE: FIAT MODEL: 500 ABARTH STYLE: HATCHBACK WARNING: NEVER EXCEED YOUR VEHICLE
More informationINSTALLATION/OPERATION
INSTALLATION/OPERATION ULTRA POWER TWIN II-30 P/N 39-941705 APPLICATION The primary purpose of your Power Twin II is to provide rock solid stabilization for maximum comfort while using your RV in a parked
More informationInstallation Instructions
Installation Instructions Automatic Retracting Running Board Vehicle Application Ford F150 Supercrew 2001-2003 (2004 Heritage) Part Number: 75111-01 www.bestop.com - We re here to help! Visit our web site
More informationLevel One Electric Vehicle Charging Station FREE STANDING Product Guide
Level One Electric Vehicle Charging Station FREE STANDING Product Guide Model # SC2-120 Shorepower Technologies 2351 NW York St. Portland, OR 98664 503-892-7345 info@shorepower.com www.shorepower.com 2
More informationFOLD N STORE. Table Tennis Table. Assembly Instructions Model DS, DS CONTACT INFO Hours.
FOLD N STORE TM PATENT - www.eastpointsports.com Table Tennis Table Assembly Instructions Model 1-1-33525-DS, 1-1-33536-DS CONTACT INFO Hours Technical Support Monday to Friday (9am to 5pm EST) Email us
More informationInstallation Instructions
Installation Instructions Application Fits 2012-2016 Tesla Model S X7201 & X7202 2 & 1.25 EcoHitch Stealth 200 lbs Tongue Weight/2,000 lbs Towing Weight Torklift Central 315 Central Ave N Kent, WA 98032
More informationInstallation Instructions
Installation Instructions ELECTRIC CONVERSION KIT 3 ALUMINUM ROLL TUBE IMPORTANT: This Electric Conversion Kit has been designed for systems with a 3 aluminum roll tube. It is assumed that the tarping
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle
More informationInstallation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab
GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill Short & Long Bed All Megacabs 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION WARNING: Under no circumstances do we
More informationTable Tennis Table. Assembly Instructions Model CONTACT INFO. Hours
FOLD N STORE PATENT - www.eastpointsports.com Table Tennis Table TWO OR MORE ADULTS REQUIRED FOR ASSEMBLY Assembly Instructions Model 1-1-33610 CONTACT INFO WARNING: CHOKING HAZARD - Small balls. Not for
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Dodge Ram 1500 Crew Cab 2009 - Current : 75138-15 Dodge Ram 2500/3500 & HD Crew Cab 2010 - Current : 75138-15
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend
More informationInstallation Instructions
Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab
More informationCOVER PAGE BASE RAIL MOUNTING KIT 10 BOLT RAIL KIT NOTE!
COVER PAGE 30035 BASE RAIL MOUNTING KIT 10 BOLT RAIL KIT NOTE! If you have a newer model year truck you must go to one our websites for the most recent updated instructions. www.reeseproducts.com or www.draw-tite.com
More informationRead and follow all instructions. Safety can only be ensured if the walker is assembled and operated according to these instructions.
Aqua Walker 9889 Garrymore Ln Missoula, MT 59808 888-687-3552 +1-406-549-0769 www.aquacreek.com Manual PART #: F-605UW 300 LB. [136 kg] MAXIMUM WEIGHT CAPACITY MANDATORY LEAVE THIS MANUAL WITH WALKER OWNER
More informationadvanced FLOW engineering Stage-2 Air Intake Instruction Manual P/N: / /
advanced FLOW engineering Stage-2 Air Intake Instruction Manual P/N: 51-76202/54-76202/75-76202 Make: Jeep Model: Wrangler (TJ) Year: 1997-2006 Engine: I6-4.0L Please read the entire instruction manual
More informationFig & MOUNTING RAIL INSTALLATION KIT
16100 & 16200 MOUNTING RAIL INSTALLATION KIT 09/28/06 CUSTOM MOUNTING BRACKETS REQUIRED ON SOME INSTALLATIONS DEALER/INSTALLER: 1) Provide this manual to end user. 2) Physically demonstrate procedure in
More informationTRAILER WINCH MODELS ST315 AND ST712. General Safety (Continued) Description. Unpacking. General Safety Information.
OPERATION AND MAINTENANCE MANUAL TRAILER WINCH READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION.
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 15/16, 15/16 Crowfoot Adaptor Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw Optional, Raise Bed: 18mm socket, 15 extension As an option you can loosen
More informationInstallation Instructions
Installation Instructions Rock Crawler Roof Rack (Part # 76717) 07-Up Jeep Wrangler J/K 4Door For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton,
More information13136 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 09-PRESENT MAKE: AUDI/PORSCHE MODEL: Q/MACAN (EXCLUDING HYBRID) STYLE: SUV WARNING: NEVER EXCEED
More informationOWNER S MANUAL. The following instructions provide valuable information regarding the function and proper use of the Super 5 th Wheel Towing System.
OWNER S MANUAL #1900 Industry Standard Super 5 th (16K) #2100 Industry Standard Super 5 th (18K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer
More information9' & 12' CHALLENGER SHUFFLEBOARD TABLE ASSEMBLY INSTRUCTIONS
9' & 12' CHALLENGER SHUFFLEBOARD TABLE ASSEMBLY INSTRUCTIONS NG1205 / NG1210 / NG1212 / NG1214 THANK YOU! Thank you for purchasing this product. We work around the clock and around the globe to ensure
More informationInstallation Instructions
Installation Instructions Application Fits 2012-2015 Honda Honda CR-V X7297 & X7298 2 & 1.25 EcoHitch Stealth 350 lb. Tongue Weight/ 3,500 lb. Towing Weight Torklift Central 315 Central Ave N Kent, WA
More informationDoing Our Best to Provide You the Best. VW Golf, GTi, Jetta PaRTs list. BOlT TORQuE specifications TP20103,Rev.4
10-09 TP20103,Rev.4 VW Golf, GTi, Jetta BOlT TORQuE specifications standard BOlTs: metric BOlTs: size Grade Torque size Torque 5/16 5 20 ft/lbs. 8mm 22 ft/lbs. 3/8 5 35 ft/lbs. 10mm 42 ft/lbs. 7/16 5 56
More informationOUTDOOR TABLE TENNIS TABLE ASSEMBLY INSTRUCTIONS
OUTDOOR TABLE TENNIS TABLE ASSEMBLY INSTRUCTIONS Please Do Not Hesitate to Contact Our Consumer Hotline at 800-759-0977 with Any Questions That May Arise During Assembly or Use of This Product! NG2336P
More information4" Oval Nerf Bar. Part No. A1003S/B. PARTS LIST: Qty Part Description Qty Part Description
` 4" Oval Nerf Bar Part No. A1003S/B Fits: 2007 - Current Chevrolet Silverado 1500/2500/3500 Crew Cab 2007 - Current GMC Sierra 1500/2500/3500 Crew Cab REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing ADARAC Truck Bed Rack. Agri-Cover, Inc. proudly manufactured this product using superior quality materials and workmanship. With proper
More information31056 INSTALLATION INSTRUCTIONS
305 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 00-00 MAKE: JEEP MODEL: COMMANDER STYLE: SUV WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationDESIGNED FOR RANGER [AND SIMILAR]
651-486-2010 info@marinetechproducts.com MODEL 35 LE 55-0350 AUXILIARY OUTBOARD MOTOR LIFT DESIGNED FOR RANGER [AND SIMILAR] FISHING BOATS This view shows the cut out on the transom plate Rev 1/16 INTRODUCTION
More informationInstallation Instructions
Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 15/16, 10 mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw 9464/9474 HIDE-A-GOOSE HITCH All Fasteners Typical, Both Sides
More informationHi-Rise 18K 5TH WHEEL CONVERSION HITCH
ASSEMBLY INSTRUCTIONS Hi-Rise 18K 5TH WHEEL CONVERSION HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. END USER: (1) Read and follow this Manual every time you use Hitch. (2) Save this Manual
More informationInstallation Instructions GOOSENECK MOUNTING KIT Toyota Tundra
GOOSENECK MOUNTING KIT Toyota Tundra 446 Equipment Required: Fastener Kit: 446F Wrenches: 10mm, 1mm, /4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Do not store hitch ball upside down in head.
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationAEROMOTIVE Part # Mustang 5.0L Fuel System Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 17103 83-93 Mustang 5.0L Fuel System Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
More informationHolley Accessory Drive Kit Part Number
Assembly Instructions Holley Accessory Drive Kit Part Number 20-132 Table of Contents Parts List:... 1 Driver s Side Bracket Installation:... 4 Power Steering Pump Installation:... 5 Idler Pulley Installation
More informationMODEL 7400 STRUT SPRING COMPRESSOR
MODEL 7400 STRUT SPRING COMPRESSOR Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV112712 P/N: 81-0103A TABLE OF
More information