Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN 55060 For a complete distributor & dealer list go to www.gandy.net 6250BN36C Orbit-Air Applicator 50 Cu. Ft. Hopper w/ 26 (1-1/4 ) Openings, Chemical Black Wheels (C) Split Shaft, Two Clutches, For 1-inch I.D. Tubing (All Hardware & Parts in Place Unless Otherwise Specified) 1... 6299-6... Mounting Base, Hopper Use: 14 Carriage Bolt (3/8 x 1) (C04-0375-040) 2 Carriage Bolt (3/8 x 1-1/4) (C04-0375-050) 16 Whiz Flange Nut (3/8) (C01-0375-030) 1... 6299-1... Hopper, 50 Cu. Ft. Use: 6 Sight Window (6299-24) 12 Rail, Large (6299-26) 12 Rail, Small (6299-27) 60 Pop Rivet (3/16 x 3/8) (C19-0187-030) 2 Decal, Gandy Orbit-Air (N02-0062-000) 1 Decal, Important Metering Wheel (N02-0062-042) 2 Decal, Caution (N02-0014-010) 1 Decal, Caution Black on Yellow (N02-0062-050) 1... 6299-2... Roof, 50-80 Cu. Ft. Use: 28 HHTC (5/16 x 1) (C03-0312-044) 28 Whiz Flange Nut (5/16) (C01-0312-030) 1... 6299-4... Cover, 50-80 Cu. Ft. 1... M05-0000-004... Rubber Latch Use: 4 Pop Rivet (3/16 x 1/4) (C19-0187-000) 2... 62852-3... Inner Hinge (For Cover) Use: 2 Hex Bolt (3/8 x 3/4) (C03-0375-040) 4 Wrought Washer (3/8) (C02-0375-030) 4 Jam Nut, Nylon Lock (3/8) (C01-0375-062) 2... 6298-15... Outer Hinge (For Cover) Use: 2 Hex Bolt (3/8 x 1) (C03-0375-041) 4 Wrought Washer (3/8) (C02-0375-030) 4 Jam Nut, Nylon Lock (3/8) (C01-0375-062) 1... 6299-33... Cover Hinge Support Rod Use: 4 Whiz Flange Nut (5/8) (C01-0625-030) 1... 0197102-1... Manual Bracket Holder (Inside Hopper) Use: 2 Cable Tie (5/16 x 15-1/4) (L04-0005-000) (Inside Hopper) 1... M10-0005-004... Manual Holder (Inside Hopper) 2... 62852-21... Shaft, Gear & Driven Sprocket (32-3/4 Long x 5/8 Round) 4... 63861-7... Plastic Bearings 8... 09074690-4... Flangette, Bearing Use: 8 Carriage Bolt (1/4 x 5/8) (C04-0250-020) 8 Whiz Flange Nut (1/4) (C01-0250-030) Page 1 of 18
2... 62851-28... Mounting Bracket, Sensor 2... 628957-1... Sensor Shaft w/ Tabs 2... 62851-42... Chain Sprocket, 21-Tooth, 5/8 Bore Use: 2 Cotter Pin (3/16 x 1-1/4) (C20-0187-030) 2... 62853-9... Sprocket, 24-Tooth (5/8 Bore 1-3/8 Hub) Use: 2 Cotter Pin (3/16 x 1-1/4) (C20-0187-030) 1... 6299-5... Shaft (71-3/4 x 1-Inch) 2... D05-1000-010... Bearing, (1-inch) Use: 4 Hex Bolt (5/16 x 3/4) (C03-0312-030) 4 Lock Washer (5/16) (C02-0312-010) 4 Hex Nut (5/16) (C01-0312-010) 2... 6298-23... Spacer (1-1/4 o.d. x 7/8 Long) 2... 62853-10... Chain Sprocket 32-Tooth (Bolted to Clutches) Use: 8 Hex Bolt (1/4 x 3/4) (C03-0250-030) 8 Whiz Flange Nut (1/4) (C01-0250-030) 1... 62853-12... Electric Clutch with 35-Tooth Sprocket Use: 1 Clutch Washer (62854-29) 1 Hex Bolt (5/16 x 5/8) (C03-0625-020) 1 Hex Bolt (3/8 x 2-1/4) (C03-0375-071) 1 Lock Washer (5/16) (C02-0312-010) 2 Whiz Flange Nut (3/8) (C02-0375-030) 1... L05-0010-001... Electric Clutch Use: 1 Clutch Washer (62854-29) 1 Hex Bolt (5/16 x 5/8) (C03-0625-020) 1 Hex Bolt (3/8 x 2-1/4) (C03-0375-071) 1 Lock Washer (5/16) (C02-0312-010) 2 Whiz Flange Nut (3/8)(C01-0375-030) 1... 52851-23... Nylon Roller Use: 1 Carriage Bolt (3/8 x 4) (C04-0375-160) 2 Wrought Washer (3/8) (C02-0375-030) 1 Lock Washer (3/8) (C02-0375-010) 1 Hex Nut (3/8) (C01-0375-010) 1 Bushing (9/16 o.d. x 3-1/4 Long) (62854-27) 1... 63862-22... Mounting Bracket, Idler Sprocket Use: 2 Hex Bolt (3/8 x 3/4) (C03-0375-030) 2 Whiz Flange Nut (3/8) (C01-0375-030) 1... 62853-17... Sprocket, 16-Tooth (3/4 I.D. x 1-1/2 Hub) (Inside Hopper) Use: 2 Socket Set Screw (1/4 x 1/4) (C06-0250-020) (In Place) 1... 63862-21... Sprocket, 16-Tooth (3/4 I.D. x 2-1/2 Hub) (Inside Hopper) Use: 2 Socket Set Screw (1/4 x 1/4) (C06-0250-020) (In Place) 1... 63862-19... Mounting Bracket, Speed Control (Mounted To Speed Control QX41) Use: 2 Hex Bolt (3/8 x 3/4) (C03-0375-030) (On Bracket) 2 Whiz Flange Nut (3/8) (C01-0375-030) (On Bracket) 1... G06-0100-000... Speed Control (QX41 CCW) (Inside Hopper) Use: 4 Hex Bolt (3/8 x 1) (C03-0375-041) (In Place) 4 Lock Washer (3/8) (C02-0375-010) (In Place) 4 Hex Nut (3/8) (C01-0375-010) (In Place) 4.88 Ft.... F02-0041-000... Roller Chain (#41) (117 Links) Use: 1 Connector Link (#41) (F02-0041-001) 1 Offset Link (#41) (F02-0041-002) Page 2 of 18
2... 63862-16... Mounting Plate, Bearing Use: 2 Carriage Bolt (3/8 x 1) (C04-0375-040) 2 Whiz Flange Nut (3/8) (C01-0375-030) 2... D05-1000-010... Bearing (1-inch) Use: 4 Hex Bolt (5/16 x 3/4) (C03-0312-030) 4 Lock Washer (5/16) (C02-0312-010) 4 Hex Nut (5/16) (C01-0312-010) 1... 63862-13... Shaft (29-1/2 Long x 1-inch Round) Use: 2 SAE Washer (1-inch) (C02-1000-020) 2... 2406251... Collar (for 1-inch Shaft) Use: 2 Sq Head Set Screw (3/8 x 5/8) (C05-0375-030) 1... 6108534-5... Sprocket, 32-Tooth (1-inch Bore) Use: 1 Cotter Pin (3/16 x 1-1/2) (C20-0187-040) 1... 6108534-9... Sprocket, 16-Tooth (1-inch Bore) Use: 1 Cotter Pin (3/16 x 1-1/2) (C20-0187-040) 2-1/8 Ft... F02-0041-000... Roller Chain (#41) (50 Rollers) Use: 1 Connector Link (#41) (F02-0041-001) 1... 6299-32... Windshield, Clear (For 50-80-100 Cu Ft Hopper) Use: 9 Hex Bolt (1/4 x 1/2) (C03-0250-010) 9 Wrought Washer (5/16) (C02-0312-030) 9 Whiz Flange Nut (1/4) (C01-0250-030) 1... 638719-3... Air Chamber, 36-Outlet (For 50-80-100 Cu Ft Hopper) Use: 1 Plate, Air Chamber (6299-40) 2 Whiz Flange Nut (1/2) (C01-0500-030) 2 Hex Bolt (3/8 x 3/4) (C03-0375-030) 2 Whiz Flange Nut (3/8) (C01-0375-030) 2... M05-2000-000... Rubber Plug (2-inch) (For Air Chamber Clean Outs) 6... M05-0187-000... Gasket, Mixing Chamber 36... M10-0055-001... Mixing Chamber, 1-1/4, Narrow Cup (For 1-inch I.D. Tubing) Use: 42 Hex Head TC Screw (5/16 x 3/4) (C03-0312-032) 1... 5508242-33... Gasket, Potting Box 1... 629066-D... Air Pressure Switch Use: 1 Air Pressure Switch Square (62851-86) 1 Mounting Plate, Square Air Pressure Switch (62851-85) 2 Pan Head TC Screw (#8 x 1/2) (C07-0164-070) 2 Hex Nut (#2-56) (C01-0086-010) 2 Pan Head Screw (#2-56 x 3/4) (C07-0086-090) 2 Wire Connector Blue (18-14ga) (L03-0005-000) 1 Wire Connector Red (22-18ga) (L03-0005-001) 1 Molded Connector, 4 Contact, 8-inch Wire (L03-0003-060) 2 628726-3 Shaft Sensor Wire (24-inch Long) 1... L10-0016-010... Potting Box Use: 2 Phillips Head TC Screw (#8-32 x 1/2) (C07-0164-070) 2... M05-4000-000... Rubber Plug (4-inch) 1... 6299-17... Clean-Out Chute (5-inch) Use: 1 Wing Nut (5/16) (C01-0312-020) 1 Wrought Washer (5/16) (C02-0312-030) 1 Decal, Caution Plug (N02-0062-051) Page 3 of 18
1... 63862-9... Angle Clamp, Tubing (For 50-80-100 Cu Ft Hopper) Use: 3 Hex Bolt (3/8 x 1) (C03-0375-041) 3 Lock Washer (3/8) (C02-0375-010) 3 Wrought Washer (3/8) (C02-0375-030) 2... 6108515... Bar Clamp, Plastic Tubing Use: 6 Hex Bolt (5/16 x 2-1/4) (C03-0312-091) 6 Wrought Washer (5/16) (C02-0312-030) 6 Lock Nut, Nylon Lock (5/16) (C01-0312-040) 1... 6298-6L... Support Bracket, Left Use: 2 Carriage Bolt (3/8 x 3/4) (C04-0375-030) 2 Whiz Flange Nut (3/8) (C01-0375-030) 1... 6298-6R... Support Bracket, Right Use: 2 Carriage Bolt (3/8 x 3/4) (C04-0375-030) 2 Whiz Flange Nut (3/8) (C01-0375-030) 1... 638614-1... Platform (For 50-80-100 Cu Ft Hopper) Use: 3 Carriage Bolt (3/8 x 3/4) (C04-0375-030) 3 Whiz Flange Nut (3/8) (C01-0375-030) 1... 638614-10... Support Angle, Platform (For 50-80-100 Cu Ft Platform) Use: 4 Carriage Bolt (5/16 x 3/4) (C04-0312-031) 4 Whiz Flange Nut (5/16) (C01-0312-030) 1... 638614-4... Railing (Fro 50-80-100 Cu Ft Hopper) Use: 3 Hex Bolt (3/8 x 1) (C03-0375-041) 3 Whiz Flange Nut (3/8) (C01-0375-030) 1... 638614-9... End Rail, Top Use: 1 U-Bolt (1/4) (638614-7) 2 Whiz Flange Nut (1/4) (C01-0250-030) 1... 6298-22... End Rail, Bottom Use: 1 U-Bolt (1/4) (638614-7) 1 Hex Bolt (5/16 x 3/4) (C03-0312-030) 2 Whiz Flange Nut (1/4) (C01-0250-030) 1 Whiz Flange Nut (5/16) (C01-0312-030) 1... 638614-6... Ladder (Banded To Platform) Use: 4 U-Bolt (1/4) (638614-7) (In Parts Bag) 8 Whiz Flange Nut (1/4) (C01-0250-030) (In Parts Bag) 2 Mounting Strap (638614-5) (In Parts Bag) 2 Black Cap (1 I.D. x 2 Inch) (J02-1000-000) (On Ladder) 4... 6299-3... Screens 2... 5508442-35... Magnetic Hub (on Hex Shaft of Metering Door) Use: 2 Spring Pins (3/16 x 1) (C23-0187-140) Page 4 of 18
2... 62852-C... Metering Door Assembly (Chemical Black Wheels) 2... 652852-11... Mounting Plate (12-Outlet) Use: 4 J-Bolt (C16-0312-020) 4 Wrought Washer (5/16) (C02-0312-030) 4 Wing Nut (5/16) (C01-0312-020) 6.38FT.... M05-0125-050... Rubber Strip w/ Adhesive 24... M10-0001-100... Metering Cup, 1-1/4 Use: 52 Whiz Flange nut (3/16) (C01-0187-030) 24... 62851-76... Hole Closure, Slotted Use: 48 Extruded Washer (628720-20) 24 Hex Bolt (5/16 x 1-3/4) (C03-0312-071) (Stainless) 24 Comp Spring (E00-0420-012) 2... 62852-14... Hex Shaft, (31-9/16 Long x 5/8 Hex) 4... 63861-7... Bearing, Plastic 8... 09074690-4... Flangette, Bearing Use: 8 Hex Bolt (1/4 x 1/2) (C03-0250-013) (Stainless) 8 Lock Washer (1/4) (C02-0250-012) (Stainless) 24... 62851-75... Metering Wheels, Chemical, Black 48... 62851-72... Wear Plate (Stainless) 2... 62851-41... Sprocket, 24 Tooth, 5/8 Bore Use: 2 Cotter Pin (3/16 x 1-1/4) (C20-0187-030) Page 5 of 18
1... 62167-C8... Blower Package, 8-GPM, Crary Fan, w/coupler 1... 62167-1... Mount Blower Use: 4 Hex Bolt (3/8 x 1-1/2) (C03-0375-061) 4 Lock Washer (3/8) (C02-0375-010) 4 Wrought Washer (3/8) (C02-0375-030) 4 Wrought Washer (1/2) (C02-0500-030) 4 Hex Nut (3/8) (C01-0375-010) 1 Warning Decal (N02-0055-010) 1 Decal, Important Hydraulic Motor (N02-0062-043) 1 Caution Decal (N02-0062-050) 1 Decal, Tag Important, Caution (N04-0000-000) 1... L01-0033-000... Fan Assembly (Crary) Use: 1 Bushing JA Type (1-inch) (L01-0033-002) 4 Hex Bolt (1/2 x 1-1/2) (C03-0500-062) 4 Lock Washer (1/2) (C02-0500-010) 4 Hex Nut (1/2) (C01-0500-010) 1... 5408320-25... Key, Fan Shaft (1/4 sq. x 1-inch Long) 1... 62167-3... Shaft (6-inch Long) 1... 28122-49... Key, Coupler (3/16 sq. x 1-inch Long) 1... K18-M024-000... Coupler (9/16 x 7/8) Replacement Parts...(K18-M024-003 Coupler Sleeve) (5508230-5 Key 1/8 x 1) (K18-M024-004 Coupler for 9/16 Shaft on Hyd Motor) (K18-M024-005 Coupler for 7/8 Shaft on End of Fan Shaft) 2... D05-1000-030... Bearing w/locking Collar (for 1-inch Shaft) 4... D10-1000-011... Flangette, Round (For D05-1000-030 Bearing) Use: 6 Carriage Bolt (5/16 x 1) (C04-0312-040) 6 Hex Nut (5/16) (C01-0312-010) 6 Lock Washer (5/16) (C02-0312-010) 1... K01-0045-003... Hydraulic Motor, 8 GPM, Casappa Use: 2 Carriage Bolt (3/8 x 1-1/4) (C04-0375-051) 2 Washer, Motor Side, Stainless (62164-2) 2 Lock Nut, Nylon (3/8) (C01-0375-041) 1... 5508336-7... Guard, Blower Shaft Use: 2 Thumb Screw (5/16 x 3/4) (C09-0312-100) 2... K02-0500-014... Hydraulic Hose, 1/2 x 14 2... K02-0500-120... Hydraulic Hose, 1/2 x 120 1... K02-0375-024... Hydraulic Hose, 3/8 x 24 (Case Drain Hose) 1... L04-0005-000... Cable Tie (5/16 x 15-1/4) 1... 62113... Hydraulic By-Pass Block Assembly w/check Valve Use: 1 Check Valve (K05-CV10-200) 1 Hydraulic By-Pass Block (6296-1) Page 6 of 18
The Following Parts Shipped Inside Hopper: 1... Parts Bag for Installing Ladder 1... 0197102-1... Manual Bracket Holder 2... L04-0005-000... Cable Tie (5/16 x 15-1/4) 1... M10-0005-004... Manual Holder 1... 6299-N... Parts Carton Containing: 1... 629066-C... Enclosed Console Assembly, 3 Light, 3 Switch 1... 5508338-23... Enclosed Console, Front 1... 5508338-24... Enclosed Console, Back Use: 4 PH HD Sheet Metal Screw (C07-0187-040) 2 Hex Bolt (1/4 x 3/4) (C03-0250-030) 2 Whiz Flange Nut (1/4) (C01-0250-030) 1... C07-0164-080... Phillips Head Screw (#8-32 x 3/8) 1... C01-0164-040... Kep Nut (#8-32) 3... M05-2858-000... Rubber Grommet (3/8) 1... L05-0008-000... Amber Light 2... L05-0008-002... Green Light 3... L05-0001-050... Switch, Toggle On/Off (#90-0001) 1... 629066-13... Molded Connector, Female, 6 Wire 1... 5508338-7... Jumper Wire, Toggle Switch 1... 62853-47... Power & Ground Wire, 10 ga. x 12 Foot 1... 5508338-10... Molded Connector, Female, 8 w/terminal on White Wire 10... L04-0005-000... Ty Rap (.31 x 15-1/4) 36FT... L05-0011-062... Flex Guard Loom (Three 12-Foot Pieces) 6... 62851-48... Blank Plate (For Unused Openings on Air Chamber) 12... 62851-66... Blank Plate (For Unused Openings on Metering Door) 1... 638616-D... Air Pressure Gauge Carton Containing: 2... C01-0250-030... Whiz Flange Nut (1/4) 1... C01-0312-030... Whiz Flange Nut (5/16) 1... C03-0312-041... Hex Bolt (5/16 x 1) 2... K04-0250-375... Adaptor, Plastic 1/4 MPT x 3/8 HB 1... K17-P743-004... Air Pressure Gauge, 4-inch 8 Ft.... M06-0375-000... Tubing, 3/8 x 1/8 wall 1... 62851-47... Clamp Bracket (For Mounting Gauge on Lifting Loop) 1... 62851-46... Mounting Bracket, Air Pressure Gauge 1... 638614-7... U-Bolt (1/4) (For Mounting on Ladder) Page 7 of 18
Hopper Assembly Page 8 of 18
Drive Shaft Assembly Part numbers with a (*) behind them have grease fittings. See page #18. Page 9 of 18
Metering Door Assembly Page 10 of 18
Air Chamber Assembly Page 11 of 18
Hydraulic Blower Assembly Page 12 of 18
Hydraulic Hose Connections Page 13 of 18
Zero-Max Assembly Page 14 of 18
Line Shaft Page 15 of 18
Chain Routing Shaft Sensor Page 16 of 18
Ladder Assembly: 1. Mount ladder (638614-6) to side of hopper as shown using the hardware provided. 2. Top bolt for mounting ladder is in place. Remove whiz nut and fasten top ladder mounting bracket here. Using a 3/8 x 3/4 hex bolt and whiz flange nut mount the bottom ladder mounting bracket to the platform as shown. Tighten bolts securely. 3. Attach ladder to railing using the two mounting straps (638614-5) and four u-bolts (638614-7) as shown. Secure in place using the 1/4 whiz flange nuts. Tighten hardware securely. Page 17 of 18
Manual Holder Bracket Mount manual holder to corner of hopper or convergent location on implement. Store Operator s manual, Packing List & Rate Chart of convergent access. Maintenance Check all bolts for tightness after first two hours of use; check periodically thereafter. Grease all fittings regularly. There are Two grease fittings on this hopper. These must be greased before use and periodically during use. Locations: See page 9. One grease fitting on each 1-inch bearing (D05-1000-010) (two) located on the 1-inch drive shaft (6299-5). One grease fitting on each 1-inch bearing (D05-1000-010) (two) located on the 1-inch line shaft (63862-13). Lucubrate chains as needed. Periodically clean intake screen on hydraulic driven blower. Drawings: 50Hopper, 66BS24, 628720-S, 62BS36, 62167-C8, 62164-CC, ZEROMAX-A, ZEROMAX-A1, LNSFT2, ZEROMAX-A2, HOPSIDE-1,62Ladder, Hold1 GDY-6250BN36C-PPL March 6, 2013 Revised From (10/14/10) Printed in the USA Page 18 of 18