Napoli wire panels
NAPOLI WIRE PANELS Epoxy-coated on galvanized core Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Mesh 100 x 55 mm Wire Ø 3,8/4,0 mm mm Ø mm cm cm 9201060 100 x 55 3,8/4,0 63 200 010016 2 9201080 100 x 55 3,8/4,0 83 200 010023 2 9201100 100 x 55 3,8/4,0 103 200 010030 2 9201120 100 x 55 3,8/4,0 123 200 010054 2 9201150 100 x 55 3,8/4,0 153 200 010078 3 9201180 100 x 55 3,8/4,0 173 200 010092 3 9201200 100 x 55 3,8/4,0 203 200 010115 4 9210060 100 x 55 3,8/4,0 63 200 028738 2 9210080 100 x 55 3,8/4,0 83 200 028745 2 9210100 100 x 55 3,8/4,0 103 200 028349 2 9210120 100 x 55 3,8/4,0 123 200 027977 2 9210150 100 x 55 3,8/4,0 153 200 028585 3 9210180 100 x 55 3,8/4,0 173 200 028653 3 9210200 100 x 55 3,8/4,0 203 200 028721 4 9220060 100 x 55 3,8/4,0 63 200 028752 2 9220080 100 x 55 3,8/4,0 83 200 028813 2 9220100 100 x 55 3,8/4,0 103 200 028769 2 9220120 100 x 55 3,8/4,0 123 200 028776 2 9220150 100 x 55 3,8/4,0 153 200 028783 3 9220180 100 x 55 3,8/4,0 173 200 028790 3 9220200 100 x 55 3,8/4,0 203 200 028806 4
PROFILE POST Profile post with cap Hot-dipped galvanized and then epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Zinc layer :180-250 g/m 2 Expoxy-coating: 54 µ Plastic collar available per piece Thickness: 1,4 mm Ø mm mm 7039 48 1000 810012 7037 48 1200 600101 7535 48 1500 390569 7042 48 1750 105538 7043 48 2000 105545 7044 48 2250 105552 7045 48 2500 105569 7501 48 3000 812559 7038 48 1000 810036 7068 48 1200 600118 7506 48 1500 390576 7057 48 1750 111638 7058 48 2000 111645 7059 48 2250 111652 7061 48 2500 111669 7505 48 3000 812573 7938 48 1000 111720 7968 48 1200 600125 7935 48 1500 390583 7957 48 1750 111751 7958 48 2000 111768 7959 48 2250 111775 7961 48 2500 111782 7507 48 3000 812597
HACCA POST Hacca post with cap Posts for wire panels to be erected simultaneously with concrete slabs. Ø mm mm 7315 1,2 1530 201070 7317 1,2 1730 201087 7320 1,2 2030 201094 7322 1,2 2250 201100 7325 1,2 2600 201117 7415 1,2 1530 200912 7417 1,2 1730 201544 7420 1,2 2030 201377 7422 1,2 2250 201551 7425 1,2 2600 201742 7515 1,2 1530 201452 7517 1,2 1730 201568 7540 1,2 2030 201575 7542 1,2 2250 201582 7545 1,2 2600 201599 FLOORPIECE FOR HACCA POST mm 7164 20 392556 7165 20 392587 7166 20 392617
PLASTIC COLLAR SUITABLE FOR POST WITH PROFILE 1 2 Plastic 1: Corner bracket 2: End/middle bracket Type 1 2 Type mm Packaging 7046 48 per piece 105576 7049 48 per piece 105606 7246 48 per piece 105699 8046 48 per 6 pieces 105507 8049 48 per 6 pieces 115605 8146 48 per 6 pieces 112369 7150 48 per piece 105712 7151 48 per piece 105729 7249 48 per piece 105866 8150 48 per 6 pieces 105705 8151 48 per 6 pieces 115728 8149 48 per 6 pieces 112376 BRACKETS SUITABLE FOR GATES Epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite on galvanized steel Plastic Ral 6005 green, Ral 9005 black or Ral 7016 anthracite mm 84109 60 105774 84119 60 105804 84121 60 105910 84020 80/80 111904 84021 80/80 111911 84022 80/80 112000
WALL FASTENING PANELS WALL FASTENING HINGES OF GATES FLOOR PIECE 84010 111744 84011 111478 84012 111485 Green epoxy-coated, on galvanized steel Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Packaging: per 4, including 8 plugs + 8 screws in plastic bag Ral 9010 810020 200950 810021 200967 810022 200974 810023 201384 alu floor piece for profile post and 48mm round post 48 and 60 mm Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Ø mm LEGNO 8031 48 012812 8033 60 012829 8131 48 012836 8133 60 012843 8035 48 012881 8135 60 012898 wooden slats for Napoli Natural screens cm 1017503 120 1 set = 38 slats 200998 1017505 150 1 set = 38 slats 201001 1017507 170 1 set = 38 slats 201018 1017509 200 1 set = 38 slats 201025
OMBRA Shade canopy Sight screen 95% sun and sight-blocking tarpaulin colour cm m 1018001 95% green 1 10 200776 1018003 95% green 1,2 10 200783 1018005 95% green 1,5 10 200790 1018007 95% green 1,8 10 200806 1018009 95% green 2 10 200813 1018101 95% black 1 10 200820 1018103 95% black 1,2 10 200837 1018105 95% black 1,5 10 200844 1018107 95% black 1,8 10 200851 1018109 95% black 2 10 200868 1018301 95% grey 1 10 201698 1018303 95% grey 1,2 10 201704 1018305 95% grey 1,5 10 201711 1018307 95% grey 1,8 10 201728 1018309 95% grey 2 10 201735 CLIPS FOR OMBRA A To attach the shade canopies to wire panels or to Gardenplast B type 1018200 A 201520 1018201 B 201537
RIBBON Ribbon, including clips 1 Rol = 60 meter = ca 3m 2 50 mm, suitable for Giardino wire panels: Napoli and Milano. mm 1017101 50 per rol 105989 1017105 50 per rol 106009 1017106 50 per rol 106054 CLIPS FOR RIBBON Clips for ribbon, for decorative applications mm 1017111 50 100 106023 1017115 50 100 106030 1017116 50 100 106061
www.giardino-online.com Check out the calculation tool for panel projects on our website
INSTRUCTIONS: PROFILE POST : PLACING IN THE GROUND 1. Purchasing tips Please note that the posts must be 50 cm above the height of the wire panels. There are end, middle and corner brackets. The number of brackets required depends on the height of the wire panels. The wire panels have a standard width of 200 cm; they can be shortened with a hacksaw. Finally, treat with rust-proof paint. Height of panel Length of post Bracket per post 63 cm 48 mm x 100 cm 2 83 cm 48 mm x 120 cm 2 103 cm 48 mm x 150 cm 2 123 cm 48 mm x 175 cm 3 153 cm 48 mm x 200 cm 3 173 cm 48 mm x 225 cm 4 203 cm 48 mm x 250 cm 4 Example For a fence of 10 m length and 153 cm height you will need: 1 straight piece without corners, i.e.: 5 panels of 153 cm 6 posts of 48 mm x 200 cm 18 brackets 2. Preparation Align the fence and dig a hole every 2 metres to a depth of 60 cm and a diameter of 30 cm. 2 meter 2 meter 3. Erecting the first post/panel Fill the first hole with a light concrete mix or stabilizer, insert the post, determine the desired height and ensure that the post is straight. Attach the first panel to the posts with brackets (do not fully tighten the screws yet) and place some wooden blocks between the panel and the ground to level the panel.
INSTRUCTIONS: PROFILE POST : PLACING IN THE GROUND 4. Erecting the second post Place the second post against the first panel, determine the correct height and insert the post into the hole filled with a light concrete mix or stabilizer. Attach the second panel to the post with brackets (do not fully tighten the screws yet) and place some wooden blocks between the panel and the ground to level the panel. 5. Subsequent panels Proceed in the same way as above until you have erected all the panels and posts. 6. Adjustment Finish installing the fence by checking and adjusting the alignment. Finally, fill the holes with the concrete mix. 7. Finishing off Allow the concrete to dry for 48 hours, then fully tighten the bracket screws and remove the wooden blocks. Watch our instruction video
INSTALLATION TIPS FOR HACCA POST - INTO THE GROUND 1. Purchasing tips When buying, please note that the posts need to be approx. 50 cm longer than the height of the panels. The panels come in a standard width of 200 cm. They can be shortened using a hacksaw. Then, they need to be treated with a rustproof paint. Panel height Post length without concrete slab Post length with concrete slab 63 cm 103 cm 123 cm 83 cm 123 cm 153 cm 103 cm 153 cm 173 cm 123 cm 173 cm 203 cm 153 cm 203 cm 225 cm 173 cm 225 cm 260 cm 203 cm 260 cm 300 cm Example For example, for a fence of 10 metres in length, and 153 cm in height with a concrete slab, 1 straight piece without corners, you would typically need: 5 panels of 153 cm 6 posts of 225 cm 2. Preparation Trace out the fence and dig one hole to a depth of approx. 60 cm and a 30 cm diameter. 3. Placing the first post/panel Fill the first hole with light-weight concrete or stabilised sand, put in the post, determine the desired height and check that the post is level. Factor in the height of the post if you are using concrete slabs (approx. 30 to 40 cm longer). Attach the first panel.
INSTALLATION TIPS FOR HACCA POST - INTO THE GROUND 4. Placing the second post Place the second post up against the first panel and then dig the second hole. Determine the right height and secure the post into place with light-weight concrete or stabilised sand. 5. Subsequent panels Continue with this procedure until all the panels and posts are in place. 6. Making the final adjustments To finish the fence, check the alignment, adjust as necessary and fill the holes with concrete. 7. Finish Leave the concrete to dry for at least 48 hours.
INSTRUCTIONS: PROFILE POST : ON BRICK, CONCRETE OR ASPHALT 1. Purchasing tips Please note that the posts must be the same height as the wire panels. There are end, middle and corner brackets. The number of brackets required depends on the height of the wire panels. The wire panels have a standard width of 200 cm; they can be shortened with a hacksaw. Finally, treat with rust-proof paint. Height of panel Length of post Brackets per post 103 cm 48 mm x 100 cm 2 123 cm 48 mm x 120 cm 3 153 cm 48 mm x 150 cm 3 173 cm 48 mm x 175 cm 4 203 cm 48 mm x 200 cm 4 Example For a fence of 10 m length and 153 cm height you will need, 1 straight piece without corners, i.e.: 5 panels of 153 cm 6 posts of 48 mm x 160 cm 18 brackets 6 floor pieces 2. Preparation Align the fence and place the first foot piece, and continue, foot piece by foot piece, until the desired length has been reached. 2 meter 2 meter
INSTRUCTIONS: PROFILE POST : ON BRICK, CONCRETE OR ASPHALT 3. Erecting the first post / panel Place the post over the foot piece and ensure the post is level. Place the profile post over the top of the foot piece and tamp the post firmly (maintaining the vertical) until the bottom of the post touches the base of the foot piece. See instruction video on our website. Attach the first panel to the post with brackets (do not fully tighten the screws yet) and place some wooden blocks between the panel and the bricks, concrete or asphalt to level the panel. 4. Erecting the second post / panel Place the second post over the foot piece and ensure the post is straight. Place the profile post over the top of the foot piece and tamp the post firmly (maintaining the vertical) until the post is the same height as the panel already erected, or until the bottom of the post touches the base of the foot piece. Attach the second panel to the post with brackets (do not fully tighten the screws yet) and place some wooden blocks between the panel and the bricks, concrete or asphalt to level the panel. 5. Subsequent panels Proceed in the same way as above until you have erected all the panels and posts. 6. Adjustment Finish installing the fence by checking and adjusting the alignment. Finally, tighten the screws.
NAPOLI GATE Hot-dip galvanized then epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Frame four pipes of Ø 40 mm Provided with: Lock with handles + 2 unique keys, Adjustable hinges, Lock stop, Wire fence panel 100 x 55 x 4,0 mm 2 gate posts of Ø 60 mm, these are 50 cm longer than the height of the gate cm cm 8100301 100 125 800211 8100303 120 125 800235 8100305 150 125 800259 8100307 170 125 800273 8100309 200 125 800297 8100321 100 125 800518 8100323 120 125 800532 8100325 150 125 800556 8100327 170 125 800570 8100329 200 125 800594 8100421 100 125 800525 8100423 120 125 800549 8100425 150 125 800563 8100427 170 125 800587 8100429 200 125 800624
NAPOLI GATE DOUBLE (2 x 200 cm) Hot-dip galvanized then epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Frame four pipes of Ø 40 mm Provided with: Lock with handles + 2 unique keys, Adjustable hinges, Lock stop, Wire fence panel 100 x 55 x 4,0 mm Hot-dip galvanized ground anchor and pin 2 square gate posts of 80 x 80 x 3 mm, these are 50 cm (by 100, 125 and 150 cm) and 60 cm (by 175 and 200 cm) longer than the height of the gate. cm cm 8100311 100 2 x 200 800617 8100313 120 2 x 200 800631 8100315 150 2 x 200 800655 8100317 170 2 x 200 800679 8100319 200 2 x 200 800693 8100351 100 2 x 200 800716 8100353 120 2 x 200 800730 8100355 150 2 x 200 800754 8100357 170 2 x 200 800778 8100359 200 2 x 200 800792 8100451 100 2 x 200 800723 8100453 120 2 x 200 800747 8100455 150 2 x 200 800761 8100457 170 2 x 200 800785 8100459 200 2 x 200 800822
NAPOLI GATE DOUBLE (2 x 150 cm) Hot-dip galvanized then epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Frame four pipes of Ø 40 mm Provided with: Lock with handles + 2 unique keys, Adjustable hinges, Lock stop, Wire fence panel 100 x 55 x 4,0 mm Hot-dip galvanized ground anchor and pin 2 square gate posts of 80 x 80 x 3 mm, these are 50 cm (by 100, 125 and 150 cm) and 60 cm (by 175 and 200 cm) longer than the height of the gate. cm cm 8100360 60 2 x 150 392662 8100331 100 2 x 150 800921 8100333 120 2 x 150 800945 8100335 150 2 x 150 800969 8100337 170 2 x 150 800983 8100339 200 2 x 150 801058 8100361 100 2 x 150 201131 8100363 120 2 x 150 201148 8100365 150 2 x 150 201155 8100367 170 2 x 150 201162 8100369 200 2 x 150 201179 8100471 100 2 x 150 800846 8100473 120 2 x 150 800860 8100475 150 2 x 150 800884 8100477 170 2 x 150 800891 8100479 200 2 x 150 800914
www.giardino-online.com Check out the calculation tool for panel projects on our website.
Garden Trade International bvba Deense Wijersstraat 6 B-3740 Munsterbilzen tel. +32-(0)89-510 360 fax +32-(0)89-510 365 info@giardino-online.com www.giardino-online.com F99997D v 2018/10 Printed on