EXTENDED WARRANTY POLICY

EXTENDED WARRANTY POLICY

EXTENDED WARRANTY TERMS AND CONDITIONS CONTENTS CONTENTS... 2 GENERAL INFORMATION... 3 EXTENDED WARRANTY: TERMS & CONDITIONS... 4 COMPONENT LIST... 11 FULL MACHINE COVERAGE... 11 CRAWLER EXCAVATOR... 11 WHEELED EXCAVATOR... 23 WHEEL LOADER... 35 ARTICULATED DUMP TRUCK... 49 POWER TRAIN COVERAGE... 63 CRAWLER EXCAVATOR... 63 WHEELED EXCAVATOR... 71 WHEEL LOADER... 79 ARTICULATED DUMP TRUCK... 87 Doosan Benelux S.A. 01 2016 2

EXTENDED WARRANTY TERMS AND CONDITIONS GENERAL INFORMATION Doosan Benelux S.A. ( DOOSAN ) offers to its dealers additional extended warranty coverage according to the terms and conditions contained in the Doosan Extended Warranty Policy ( Extended Policy ). Doosan reserves the right to refuse any element of the warranty if it deems at its sole discretion that the terms and conditions and warranty processes laid down in the Extended Policy have not been adhered to. For warranty enquiries, contact: Doosan Benelux S.A. Warranty Department EMEA Drève Richelle 167; B-1410 Waterloo, Belgium T: +32 (0) 2 371 68 11 E: doosanwarranty@doosan.com W: http://www.doosanequipment.com For details of Doosan Warranty procedures and literature, and for assistance in claim submission, refer to the Doosan Passport website ( Passport ) and the Doosan Warranty System ( IRW ). Website Link: https://www.doosanpassport.com The original language of this document is English and all translations are for reference purposes only. This Extended Warranty Policy is published to assist Dealers of Doosan-branded products in managing the extended warranty coverage. This manual may be revised to reflect changes in policies and procedures as they occur. This manual supersedes all previously published Extended Warranty policies and procedures. This manual does not supersede any extended warranty plan previously granted and still in force. Doosan Benelux S.A. 01 2016 3

EXTENDED WARRANTY TERMS AND CONDITIONS EXTENDED WARRANTY: TERMS & CONDITIONS 1. TERMS AND COVERAGE TYPES For a fee to be paid by the dealer, DOOSAN would provide one of the following extended warranty plans. Extended programmes are available for purchase through the Doosan Online Store (www.diipartner.net): Coverage type Covered Total months covered* Total operating hours covered* Standard Extension Parts, Labour & Mileage 24 4000 Standard Extension Parts, Labour & Mileage 36 6000 Standard Extension Parts, Labour & Mileage 48 8000 Standard Extension Parts, Labour & Mileage 60 10000 Protection Plus Parts, Labour & Mileage 24 4000 Protection Plus Parts, Labour & Mileage 36 6000 Protection Plus Parts, Labour & Mileage 48 8000 Protection Plus Parts, Labour & Mileage 60 10000 Power Train Parts only 24 4000 Power Train Parts only 36 6000 *Including standard warranty period All maintenance and repairs of a machine covered by a Standard Warranty Extension and Protection Plus must be made by a Doosan recognised dealer using Doosan genuine spare parts and consumables purchased from Doosan. Subscription for Protection Plus requires a signed copy of the Maintenance Contract and the acceptance of DOOSAN at the time of the request in the Doosan Online Store. Doosan will, at any time, cancel the warranty extension, without providing any refund, if the maintenance contract was not provided. Doosan Benelux S.A. 01 2016 4

EXTENDED WARRANTY TERMS AND CONDITIONS A Maintenance Contract is defined as a signed service level agreement between dealer and endcustomer guaranteeing the equipment to be serviced according to DOOSAN prescribed intervals and specifications referred to in the DOOSAN Operation and Maintenance Manual. Parts, Labour & Mileage represent Full Coverage of the equipment components. The warranty period detailed above in months or hours, whichever occurs first, applies as from the date of delivery of the machine to the first end-user. Dealer rental fleet units are fully eligible for all coverage types. Machines working in forestry and demolition applications are excluded from any of the extended warranty plans. The following models are not eligible to be covered by any of the extended warranty plans: DX300 DX225SLR DX520SLR DEM DX160WR DX340 DX255SLR DX190MH DEM DX700W DX420 DX300SLR DX210MH DEM Except where the present policy provides for different rules, the Standard Warranty Policy of DOOSAN applies to the Extended Warranty. Doosan Benelux S.A. 01 2016 5

EXTENDED WARRANTY TERMS AND CONDITIONS 2. APPLICABLE MODELS The models eligible to be covered by an extended warranty plan are identified on the extended warranty price list displayed in the Doosan Online Store (www.diipartner.net). 3. COVERAGE Extended warranty applies to failures found during the coverage period due to a defect in material and/or workmanship. DOOSAN shall in no event be liable for any other losses, damages, costs or expenses claimed by the end-user, including but not limited to loss from failure of the machine to operate for any period of time, property damage and all other direct, indirect, special incidental or consequential damages, whether arising under contract, warranty negligence, strict liability or any other legal theory whatsoever. Components covered or not covered Please refer to individual product component lists attached to the present policy. Any component not mentioned in the included sections is by definition excluded. General exclusions: Maintenance parts: oil, coolant, additives, lubricants, fluids, belts, filters & filter elements, additives, breathers Wear parts: including but limited to fuses, wiper blades, lamps & light bulbs, paint, labels Components failing due to normal wear and tear Components covered by other manufacturers warranty (including but not limited to Cummins engines, tyres,...) Conditions covered or not covered The machine must not have been neglected, misused or modified out of the manufacturer s written recommended specification. The machine must have been serviced as recommended in the owner s manual and using only genuine DOOSAN parts. Machine must be serviced by an authorised Doosan Dealer and Doosan Benelux S.A. 01 2016 6

EXTENDED WARRANTY TERMS AND CONDITIONS trained personnel. Machines working in forestry and demolition applications are excluded from any of the extended warranty plans. Replacement or rebuild or parts and/or components required because they have exceeded their expected life, due to normal wear and tear, does not constitute a defect in material or workmanship. Therefore, such repairs are not covered under extended warranty. Limitations DOOSAN reserves the right to request at any point proof of compliance with maintenance intervals (customer invoice mentioning machine serial number, machine hours and maintenance description and/or dealer work order for maintenance performance). Failure to provide requested documentation will result in non-acceptance of the extended warranty claim. DOOSAN reserves the right to request failed parts to be returned to DOOSAN for inspection and analysis. Failure to return the parts when specifically requested by DOOSAN will result in non-acceptance of the extended warranty claim. DOOSAN reserves the right to request detailed failure information including troubleshooting data and DMS output data. Failure to provide requested information when specifically requested by DOOSAN will result in non-acceptance of the extended warranty claim. No coverage will be honoured if the defect has been caused, in whole or in part, by the fitting of any service part or attachment not manufactured or approved in writing by DOOSAN. Details of any attachments and modifications made to the machine by the dealer must be registered with DOOSAN. Cancellation Doosan will cancel the extended warranty in the following situations: Failing to maintain the machine in accordance with the instructions of the Operation and Maintenance Manual. Failing to ensure maintenance and service is performed by an authorised DOOSAN Dealer. Failing to provide required oil sampling on specific DOOSAN request. Any alteration or modification to the machines affecting function and/or any component, without prior written approval by DOOSAN. Failing to use the machine according to DOOSAN s utilisation specifications (e.g. operation of the unit above the designed and specified capacity of the unit). Use of non-genuine DOOSAN parts and/or components. Operating the machine with contaminated fuel, oil, coolants or filters. Failing to notify within 72 hours indications of potential failure (e.g. improper machine operation, oil analysis indication or complaints from customer). Doosan Benelux S.A. 01 2016 7

EXTENDED WARRANTY TERMS AND CONDITIONS Failing to pay the extended warranty invoice within the dealer payment conditions. In the above-mentioned cases, the dealer will not be entitled to request any partial or full reimbursement of the price of the extended warranty. 4. REPLACEMENT PARTS DOOSAN parts used for warranty repairs are covered for the remaining term of this extended warranty (or duration of the six months Parts coverage, whichever occurs first). 5. DEALER RESPONSIBILITY The dealer will make sure that the product is delivered in good condition and that the conditions of the programme as well as the customer responsibilities are conveyed to the customer. The dealer agrees to instruct and train the customer on daily maintenance operation. The dealer agrees to ensure that the machine was sold in the correct application and used within designed capacity and specification. 6. CUSTOMER RESPONSIBILITY The Customer agrees to maintain the machine as per the latest available published DOOSAN operation and maintenance information. The Customer agrees to notify the Dealer promptly (by fax, e-mail or by telephone) of any machine abnormalities. The Customer agrees to use only genuine DOOSAN parts, supplied through a DOOSAN Dealer, in the normal maintenance and repair of the machine for the terms of this extended warranty. Machine transportation costs and other related expenses are the end-user's responsibility (e.g. downtime compensation, hire facility, replacement machine costs, ). The customer agrees to correctly operate the machine in an application approved by DOOSAN. Doosan Benelux S.A. 01 2016 8

EXTENDED WARRANTY TERMS AND CONDITIONS 7. REGISTRATION PROCEDURE At the time of delivery to the first end-user, the dealer must fully explain the terms and conditions of the standard and extended warranty coverage to the customer. The machine inspection check book must be signed by the dealer representative and the customer at the time of machine delivery. Delivery reports must be submitted online in the DOOSAN Online Warranty System (IRW) section within 5 days of delivery of the unit to the end-customer. Dealer must inform the customer of what is exactly covered. The Extended Warranty must be submitted online via the Doosan Online Store (www.diipartener.net) to the DOOSAN Customer Service Department within 30 days of delivery date ( = physical retail date of the machine to the first end-user; the delivery date is displayed in the IRW system ). Any Protection Plus registration requests must be accompanied by a copy of the Maintenance Agreement that was signed between the End-Customer and the Dealer. The extended warranty plan can be purchased only after the delivery report has been submitted. Dealer has a RIGHT OF WITHDRAWAL of at least 30 calendar days, starting from the day of the purchase of the extended package; this gives the opportunity to return the item without any obligations. If Dealer would like to make use of the right of withdrawal, it must request this to Doosan via email within 30 calendar days from the invoice date of the extended warranty plan. In such event, Doosan will reimburse the full amount paid by the dealer. For any cancellation requested after this period, the dealer is not entitled to request any partial or full reimbursement of the price of the extended warranty. 8. WARRANTY CLAIM PROCEDURE The warranty claim submission must be in accordance with the standard procedure as described in the DOOSAN Standard Warranty Policy Manual. The warranty claim, referring to the standard time and to any of the extended warranty plan period, must be submitted through the online Warranty System (IRW). Any procedural questions in connection with warranty claims should be addressed to the Warranty Department. Doosan Benelux S.A. 01 2016 9

EXTENDED WARRANTY TERMS AND CONDITIONS 9. COMPENSATION Parts, labour and mileage costs (depending on the chosen coverage type) will be compensated at the standard warranty rate and on the condition that the warranty claim complies with the conditions as outlined in the DOOSAN Standard Warranty Policy Manual. The standard warranty rates are applicable to the following plans: Standard extension (Parts, labour and mileage costs) Power Train (Parts only) The compensation will be made according to the standard warranty scheme: Labour and mileage will be reimbursed at Standard Rates Parts as per Doosan invoice price (refer to Claim Reimbursement in the Standard Warranty Policy Manual). The Protection Plus compensation will be made as follows: First year, it will follow the standard warranty scheme As of the second year till the end of the coverage: o Labour and mileage will be reimbursed at 100% of the full shop rate o Parts at Dealer Net price + 33% 10. TRANSFER OF EXTENDED WARRANTY A remainder of the extended warranty (Standard Extension, Protection Plus and Power Train) coverage can be transferred to another customer, provided that the new end-customer is able to provide proof of the remaining warranty coverage noted on his purchase invoice. Transfer of the extended warranty is only possible when proof can be provided that all required maintenance has been completed by the original DOOSAN dealer according to schedule. An Equipment Transfer Report (ETR) must be filled out on the online Warranty System, IRW (www.doosanpassport.com). Should there be any dealer rental unit covered by Protection Plus and sold to a second owner, it is the dealer s obligation to ensure a signed maintenance contract covering the rest of the extended warranty period. If no agreement is provided, Doosan can cancel the plan, with no refund, at any time. DOOSAN has the option to inspect the unit prior to approval as well as the option to reject any warranty transfer request. In this case, neither the former owner nor the new owner are eligible for a partial or full reimbursement of the price of the extended warranty. Doosan Benelux S.A. 01 2016 10

FULL COVERAGE - CRAWLER EXCAVATOR COMPONENT LIST FULL MACHINE COVERAGE (STANDARD EXTENSION AND PROTECTION PLUS) CRAWLER EXCAVATOR The following sections specify which components are covered against failure as defined in the policy, subject to the equipment being fully serviced in accordance with the DOOSAN service instructions and the intervals recommended by DOOSAN. Limits of indemnity and period(s) of cover are detailed in the policy. The following functional areas are detailed below: Engine Fuel Systems Cooling system Hydraulics Electrics Undercarriage Main frame Front end equipment Doosan Benelux S.A. 01 2016 11

FULL COVERAGE - CRAWLER EXCAVATOR ENGINE air heater balance assemblies block bushes camshaft and followers Connecting rod connecting rods bearings crankshaft cylinder head cylinder liners external pipes external pump drive gear flywheel head gasket Internal oil seals lubrication pump and drive components including failure of casting assembly main bearings piston pins piston rings Pistons push rods spring and guides timing gears Tappets thrust bearings internal oil seals (internal failure) turbo charger (up to 36 months/6000 hrs from delivery) Valves Doosan Benelux S.A. 01 2016 12

FULL COVERAGE - CRAWLER EXCAVATOR ENGINE (continued) Air cleaner adjustment of any type including adjustments of engine timing all exhaust components including exhaust manifold contamination deterioration due to age, ingress of dust or foreign matter resulting in engine failure failure due to normal wear and tear failure due to use of fuel of incorrect specification failure resulting from the engine being operated beyond its design speed Hoses Mountings pre-cleaner stop cables throttle cable valves when burnt and / or pitted Doosan Benelux S.A. 01 2016 13

FULL COVERAGE - CRAWLER EXCAVATOR FUEL SYSTEMS fuel transfer pump (internal fuel pump) fuel injection pump fuel tanks adjustment and/or calibration blockages caused by contamination damage resulting from failure to monitor and drain condensation from fuel system damage resulting from the ingress of water or dirt failure by the removal of filler screen where the specification requires it to be fitted resulting in contamination of the system Failures due to fuel contamination failure due to use of incorrect fuel specification for this unit failures due to the breaking of the fuel injection pump seal or re-tuning of the injection pump or engine control unit (ECU) effecting emission controls fittings fuel refilling pump (external fuel pump) hoses injectors sediment bowl Doosan Benelux S.A. 01 2016 14

FULL COVERAGE - CRAWLER EXCAVATOR COOLING SYSTEM After/inter coolers internal bearing and seals oil coolers radiators thermostat Water pump air filter assemblies on cab heater damage due to use of contaminated water and antifreeze of unsatisfactory specification damage to components resulting from the failure to use or maintain inhibitors as required in original specification frost damage or blockage to radiators and pipes general frost damage pipes water hoses Doosan Benelux S.A. 01 2016 15

FULL COVERAGE - CRAWLER EXCAVATOR ELECTRICS air conditioning alternator controller electric instrument panel electrical control motor electronic control unit electrical fuel feed pump hour meter switches, micro switches Senders & sensors solenoid valves solenoids starter motor Wiper motors gauges heater motors Doosan Benelux S.A. 01 2016 16

FULL COVERAGE - CRAWLER EXCAVATOR ELECTRICS (continued) alternator drive pulley audio-vision alarms Battery cigar lighter corroded terminals damage resulting from dust inside the cab damage to alternator or any electrical component resulting from the failure to disconnect the battery during welding or incorrect jump starting methods damage to components due to fuel/oil water contamination indicators lights radio Relays speakers Wiring Doosan Benelux S.A. 01 2016 17

FULL COVERAGE - CRAWLER EXCAVATOR HYDRAULICS accumulators centre joints Hydraulic valves hydraulic cylinders (rams) Hydraulic motor hydraulic tank joysticks electro valves swing gearbox swing motors hydraulic pumps O Rings centre joint seals contamination due to the ingress of water or dirt damage caused by the failure to use the correct specification oil exposed pipes external seals hoses hydraulic cylinder seals hydraulic pipes and connections hydraulic tank breathers impact damage improper maintenance and service use of non-approved hydraulic modifications and attachments. rubber mountings Doosan Benelux S.A. 01 2016 18

FULL COVERAGE - CRAWLER EXCAVATOR UNDERCARRIAGE Bearing shafts bull gears crown wheels final drive shafts idlers (for breakage) input seals (internal failure) pinions rollers (for breakage) seals shoes (for breakage) springs (for breakage). sprockets (for breakage where applicable) thrust washers track frames track links (for breakage) travel motors Doosan Benelux S.A. 01 2016 19

FULL COVERAGE - CRAWLER EXCAVATOR UNDERCARRIAGE (continued) continuous overloading of the front idlers (tiptoeing) damage caused by over speed damage caused by the failure to maintain the final drive casing breathers (where applicable) damage caused by the ingress/contamination by dirt and or water damage resulting from the incorrect mounting/fitting of the drive sprocket/segments damage to the running gear resulting from crushing drive sprockets for wear hoses and clamps Idlers for wear impact damage resulting in the failure of a cover component pad bolts for wear piping roller for wear track covers for wear Track links for wear track shoes for wear tracks pins for wear tracks/chains Should operational conditions reduce the life of any running gear components, then the premature replacement of these affected components will be at the customer s expense. Doosan Benelux S.A. 01 2016 20

FULL COVERAGE - CRAWLER EXCAVATOR MAIN FRAME Counterweight. main frame Castings and casings, providing that the damage has been caused by internal failure only pinion Slew ring catches and handles control stand damage resulting from continuous overloading damage resulting from continuous use on unsuitable ground damage resulting from failure to carry out recommended inspections damage resulting from using the machine without belly plates or other form of protection glass impact damage from external resources impact damage resulting from swing overhand collisions rubber components seat wear to swing brake Doosan Benelux S.A. 01 2016 21

FULL COVERAGE - CRAWLER EXCAVATOR FRONT END EQUIPMENT arm boom (mono boom or two piece boom) linkage bucket bushings continuous overloading dust seals damage caused by the failure to carry out recommended inspections failures due to improper maintenance and service failures resulting from incorrect methods of operation fixing bolts and clamps hydraulic hoses and pipes impact damage to cover components lubrication fittings pins side cutters spacers teeth All attachments must be of an approved specification. Doosan Benelux S.A. 01 2016 22

FULL COVERAGE WHEELED EXCAVATOR WHEELED EXCAVATOR The following sections specify which components are covered against failure as defined in the policy, subject to the equipment being fully serviced in accordance with the DOOSAN service instructions and the intervals recommended by DOOSAN. Limits of indemnity and period(s) of cover are detailed in the policy. The following functional areas are detailed below: Engine Fuel Systems Cooling system Hydraulics Electrics Drive axle, drive line Steering Main frame Front end equipment Doosan Benelux S.A. 01 2016 23

FULL COVERAGE WHEELED EXCAVATOR ENGINE air heater balance assemblies block bushes camshaft and followers Connecting rod connecting rods bearings crankshaft cylinder head cylinder liners external pipes external pump drive gear flywheel head gasket Internal oil seals lubrication pump and drive components including failure of casting assembly main bearings piston pins piston rings Pistons push rods spring and guides timing gears Tappets thrust bearings internal oil seals (internal failure) turbo charger (up to 36 months/6000 hrs from delivery) Valves Doosan Benelux S.A. 01 2016 24

FULL COVERAGE WHEELED EXCAVATOR ENGINE (continued) Air cleaner adjustment of any type including adjustments of engine timing all exhaust components including exhaust manifold and contamination deterioration due to age, ingress of dust or foreign matter resulting in engine failure failure due to normal wear and tear failure due to use of fuel of incorrect specification failure resulting from the engine being operated beyond its design speed hoses mountings pre-cleaner stop cables throttle cable valves when burnt and / or pitted Doosan Benelux S.A. 01 2016 25

FULL COVERAGE WHEELED EXCAVATOR FUEL SYSTEMS fuel transfer pump (internal fuel pump) fuel injection pump fuel tanks adjustment and/or calibration blockages caused by contamination damage resulting from failure to monitor and drain condensation from fuel system damage resulting from the ingress of water or dirt failure by the removal of filler screen where the specification requires it to be fitted resulting in contamination of the system Failures due to fuel contamination failure due to use of incorrect fuel specification for this unit failures due to the breaking of the fuel injection pump seal or re-tuning of the injection pump or engine control unit (ECU) effecting emission controls fittings fuel refilling pump (external fuel pump) hoses injectors sediment bowl Doosan Benelux S.A. 01 2016 26

FULL COVERAGE WHEELED EXCAVATOR COOLING SYSTEM After/inter coolers internal bearing and seals oil coolers radiators thermostat Water pump air filter assemblies on cab heater damage due to use of contaminated water and antifreeze of unsatisfactory specification damage to components resulting from the failure to use or maintain inhibitors as required in original specification frost damage or blockage to radiators and pipes general frost damage pipes water hoses Doosan Benelux S.A. 01 2016 27

FULL COVERAGE WHEELED EXCAVATOR HYDRAULICS accumulators centre joints hydraulic valves hydraulic cylinders (rams) Hydraulic motor hydraulic tank joy sticks electro valves swing gearbox swing motors hydraulic pumps O Rings centre joint seals contamination due to the ingress of water or dirt damage caused by the failure to use the correct specification oil exposed pipes external seals hoses hydraulic cylinder seals hydraulic pipes and connections hydraulic tank breathers impact damage improper maintenance and service use of non-approved hydraulic modifications and attachments. rubber mountings Doosan Benelux S.A. 01 2016 28

FULL COVERAGE WHEELED EXCAVATOR ELECTRICS air conditioning alternator controller electric instrument panel electrical control motor electronic control unit Electrical fuel feed pump gauges hour meter Switches, micro switches regulator Senders and sensors solenoid valves solenoids starter motor Wiper motors heater motors Doosan Benelux S.A. 01 2016 29

FULL COVERAGE WHEELED EXCAVATOR ELECTRICS (continued) alternator drive pulley audio-vision alarms Battery cigar lighter corroded terminals damage resulting from dust inside the cabin damage to alternator or any electrical component resulting from the failure to disconnect the battery during welding or incorrect jump starting methods damage to components due to fuel/oil water contamination indicators lights radio Relays speakers Wiring Doosan Benelux S.A. 01 2016 30

FULL COVERAGE WHEELED EXCAVATOR DRIVE AXLES, DRIVE LINES all bearings crown wheel and pinion drive shafts drop box half shafts hub assemblies (including seal carriers and bearings) internal oil seals reduction gears contamination due to water and / or dirt damage resulting from the incorrect use of all wheel drive components damage resulting from the failure to maintain differential breather in clean and serviceable condition external damage to seals failures due to axle and drive line distortion hoses damage of input and output drive flanges as a result of unit being operated with worn / damaged or seized drive shafts pipes universal joints Doosan Benelux S.A. 01 2016 31

FULL COVERAGE WHEELED EXCAVATOR STEERING internal drive couplings orbital valve power steering pump relief valves steering rams steering valves Hose and fittings ball joints damage resulting from the vehicle becoming bogged down failure of any steering components due to the unit being rolled over and incorrectly recovered steering stops steering wheel track rod ends wear on components resulting from lack of service adjustments and incorrect lubrication methods Doosan Benelux S.A. 01 2016 32

FULL COVERAGE WHEELED EXCAVATOR MAIN FRAME counterweight main frame Castings and casings, providing that the damage has been caused by internal failure only pinion Slew ring catches and handles control stand damage resulting from continuous overloading damage resulting from continuous use on unsuitable ground damage resulting from failure to carry out recommended inspections damage resulting from using the machine without belly plates or other form of protection glass impact damage from external resources impact damage resulting from swing overhand collisions rubber components seat Site damage to outrigger feet wear to swing brake Wear to dozer and frame Wear to outrigger feet Doosan Benelux S.A. 01 2016 33

FULL COVERAGE WHEELED EXCAVATOR FRONT END EQUIPMENT arm Boom (mono boom or two piece boom) linkage bucket and bucket teeth bushings consumable parts continuous overloading dust seals damage caused by the failure to carry out recommended inspections failures due to improper maintenance and service failures resulting from incorrect methods of operation fixing bolts and clamps hydraulic hoses and pipes impact damage to cover components lubrication fittings pins side cutters spacers All attachments must be of an approved specification. Doosan Benelux S.A. 01 2016 34

FULL COVERAGE WHEEL LOADER WHEEL LOADER The following sections specify which components are covered against failure as defined in the policy, subject to the equipment being fully serviced in accordance with the DOOSAN service instructions and the intervals recommended by DOOSAN. Limits of indemnity and period(s) of cover are detailed in the policy. The following functional areas are detailed below: Engine Fuel Systems Cooling system Hydraulics Electrics Frame Drive axles, drive lines Transmission Brake components steering Doosan Benelux S.A. 01 2016 35

FULL COVERAGE WHEEL LOADER ENGINE air heater balance assemblies block bushes camshaft and followers Connecting rod connecting rods bearings crankshaft cylinder head cylinder liners external pipes external pump drive gear flywheel head gasket Internal oil seals lubrication pump and drive components including failure of casting assembly main bearings piston pins piston rings Pistons push rods spring and guides timing gears Tappets thrust bearings internal oil seals (internal failure) turbo charger (up to 36 months/6000 hrs from delivery) Valves Doosan Benelux S.A. 01 2016 36

FULL COVERAGE WHEEL LOADER ENGINE (continued) Air cleaner adjustment of any type including adjustments of engine timing all exhaust components including exhaust manifold and contamination deterioration due to age, ingress of dust or foreign matter resulting in engine failure failure due to normal wear and tear failure due to use of fuel of incorrect specification failure resulting from the engine being operated beyond its design speed hoses mountings pre-cleaner stop cables throttle cable valves when burnt and / or pitted Doosan Benelux S.A. 01 2016 37

FULL COVERAGE WHEEL LOADER FUEL SYSTEMS fuel transfer pump (internal fuel pump) fuel injection pump fuel tanks adjustment and/or calibration blockages caused by contamination damage resulting from failure to monitor and drain condensation from fuel system damage resulting from the ingress of water or dirt failure by the removal of filler screen where the specification requires it to be fitted resulting in contamination of the system Failures due to fuel contamination failure due to use of incorrect fuel specification for this unit failures due to the breaking of the fuel injection pump seal or re-tuning of the injection pump or engine control unit (ECU) effecting emission controls fittings fuel refilling pump (external fuel pump) hoses injectors sediment bowl Doosan Benelux S.A. 01 2016 38

FULL COVERAGE WHEEL LOADER COOLING SYSTEM After/inter coolers internal bearing and seals oil coolers radiators thermostat Water pump damage due to use of contaminated water and antifreeze of unsatisfactory specification damage to components resulting from the failure to use or maintain inhibitors as required in original specification frost damage or blockage to radiators and pipes general frost damage Pipes water hoses Doosan Benelux S.A. 01 2016 39

FULL COVERAGE WHEEL LOADER ELECTRICS air conditioning alternator controller hour meter Switches, micro switches regulator electric instrument panel electrical control motor electronic control unit electrical fuel feed pump gauges heater motors Senders & switches solenoid valves solenoids starter motor Wiper motors Doosan Benelux S.A. 01 2016 40

FULL COVERAGE WHEEL LOADER ELECTRICS (continued) alternator drive pulley audio-vision alarms Battery cigar lighter corroded terminals damage resulting from dust inside the cabin damage to alternator or any electrical component resulting from the failure to disconnect the battery during welding or incorrect jump starting methods damage to components due to fuel/oil water contamination indicators lights radio speakers relays wiring Doosan Benelux S.A. 01 2016 41

FULL COVERAGE WHEEL LOADER HYDRAULICS accumulators hydraulic valves hydraulic cylinders (rams) Hydraulic fan motor hydraulic pumps hydraulic tank joy sticks electro valves O Rings centre joint seals contamination due to the ingress of water or dirt damage caused by the failure to use the correct specification oil exposed pipes external seals hoses hydraulic cylinder seals hydraulic pipes and connections impact damage improper maintenance and service use of non-approved hydraulic modifications and attachments rubber mountings Doosan Benelux S.A. 01 2016 42

FULL COVERAGE WHEEL LOADER DRIVE AXLES, DRIVE LINES all bearings Bevel and pinion gear Differential gears drive shafts drop box Gears half shafts hub assemblies (including seal carriers and bearings) internal oil seals Universal joints reduction gears Doosan Benelux S.A. 01 2016 43

FULL COVERAGE WHEEL LOADER DRIVE AXLES, DRIVE LINES (continued) Brake discs and brake plates contamination due to water and / or dirt damage of input and output drive flanges as a result of unit being operated with worn / damaged or seized drive shafts damage resulting from the incorrect use of all wheel drive components damage resulting from the failure to maintain differential breather in clean and serviceable condition damage resulting from the use of solid (foam or water filled) tires external damage to seals failures due to axle and drive line distortion Hoses Limited slip discs and plates Pipes universal joints Doosan Benelux S.A. 01 2016 44

FULL COVERAGE WHEEL LOADER TRANSMISSION charging pumps, Bearings Bushes Couplings drive shafts electronic transmission controller gear train and shafts, gears, input and output seals (internal failure) internal seals needle roller bearings oil lubrication pumps relief valves thrust washers torque converter transmission control valve and solenoids all rubber mounting brackets any failures occurring due to the failure to change the transmission oil at the recommended time or to maintain the oil at the correct level within the transmission assembly damage resulting from the incorrect use of all wheel drive components damage to transmission condition external damage to transmission casing external hoses and fittings failure due to contamination failures due to the use of non-recommended lubrication filter wiring harness Transmission discs and plates Doosan Benelux S.A. 01 2016 45

FULL COVERAGE WHEEL LOADER BRAKE COMPONENTS Accumulator brake pedal lever and mounting linkage parking brake parking brake valve All other brake components brake callipers and seals brake discs / drums / brake packs (wear and heat damage) brake linings brake pads brake shoes damage caused by contamination by oil or water / condensation damage caused by frost damage caused to the parking brake through the machine being operated with the brake still on hoses and fittings Doosan Benelux S.A. 01 2016 46

FULL COVERAGE WHEEL LOADER STEERING Emergency steering electromotor Emergency steering pump Emergency steering control valve Steering unit (orbitrol) hydraulic steering pump relief valves steering cylinders (rams) steering valves Hose and fittings ball joints damage resulting from the vehicle becoming bogged down failure of any steering components due to the unit being rolled over and incorrectly recovered steering stops steering wheel track rod ends wear on components resulting from lack of service adjustments and incorrect lubrication methods Doosan Benelux S.A. 01 2016 47

FULL COVERAGE WHEEL LOADER FRAME Lift arm Front and rear frames Castings and casings, providing that the damage has been caused by internal failure only Bucket bucket teeth bolts and clamps cutting edge damage caused by excessive overloading damage caused by the failure to carry out lubrication at the recommended intervals damage caused by the failure to maintain the lift and bucket stops dust seals failure due to improper maintenance and service failure to maintain recommended chassis inspections resulting in major failure failures due to incorrect operation / use of the machine failures to any pin locations due to a lack a of grease fixing bolts hydraulic hoses and pipes impact damage Z-bar linkage, parallel linkage Doosan Benelux S.A. 01 2016 48

FULL COVERAGE ARTICULATED DUMP TRUCK ARTICULATED DUMP TRUCK The following sections specify which components are covered against failure as defined in the policy, subject to the equipment being fully serviced in accordance with the DOOSAN service instructions and the intervals recommended by DOOSAN. Limits of indemnity and period(s) of cover are detailed in the policy. The following functional areas are detailed below: Engine Fuel Systems Cooling system Hydraulics Electrics Frame Drive axles, drive lines Transmission Brake components Steering Doosan Benelux S.A. 01 2016 49

FULL COVERAGE ARTICULATED DUMP TRUCK ENGINE air heater balance assemblies block bushes camshaft and followers connecting rod connecting rods bearings crankshaft cylinder head cylinder liners external pipes external pump drive gear flywheel head gasket internal oil seals lubrication pump and drive components including failure of casting assembly main bearings piston pins piston rings Pistons push rods spring and guides timing gears tappets thrust bearings turbo charger (up to 36 months/6000 hrs from delivery) Valves camshaft bearings Doosan Benelux S.A. 01 2016 50

FULL COVERAGE ARTICULATED DUMP TRUCK ENGINE (continued) air cleaner adjustment of any type including adjustments of engine timing all exhaust components including exhaust manifold and contamination deterioration due to age, ingress of dust or foreign matter resulting in engine failure failure due to normal wear and tear failure due to use of fuel of incorrect specification failure resulting from the engine being operated beyond its design speed hoses mountings pre-cleaner stop cables throttle cable valves when burnt and / or pitted Doosan Benelux S.A. 01 2016 51

FULL COVERAGE ARTICULATED DUMP TRUCK FUEL SYSTEMS fuel transfer pump (internal fuel pump) fuel injection pump fuel tanks adjustment and/or calibration blockages caused by contamination damage resulting from failure to monitor and drain condensation from fuel system damage resulting from the ingress of water or dirt failure by the removal of filler screen where the specification requires it to be fitted resulting in contamination of the system Failures due to fuel contamination failure due to use of incorrect fuel specification for this unit failures due to the breaking of the fuel injection pump seal or re-tuning of the injection pump or engine control unit (ECU) effecting emission controls fittings fuel refilling pump (external fuel pump) hoses injectors sediment bowl Doosan Benelux S.A. 01 2016 52

FULL COVERAGE ARTICULATED DUMP TRUCK COOLING SYSTEM after/inter coolers internal bearing and seals oil coolers radiators thermostat Water pump damage due to use of contaminated water and antifreeze of unsatisfactory specification damage to components resulting from the failure to use or maintain inhibitors as required in original specification frost damage or blockage to radiators and pipes general frost damage pipes water hoses Doosan Benelux S.A. 01 2016 53

FULL COVERAGE ARTICULATED DUMP TRUCK ELECTRICS air conditioning alternator controller electric instrument panel electrical control motor electronic control unit electrical fuel feed pump gauges hour meter switches, micro switches regulator senders & switches solenoid valves solenoids starter motor wiper motors heater motors Doosan Benelux S.A. 01 2016 54

FULL COVERAGE ARTICULATED DUMP TRUCK ELECTRICS (continued) alternator drive pulley audio-vision alarms battery cigar lighter corroded terminals damage resulting from dust inside the cabin damage to alternator or any electrical component resulting from the failure to disconnect the battery during welding or incorrect jump starting methods damage to components due to fuel/oil water contamination indicators lights radio speakers relays wiring Doosan Benelux S.A. 01 2016 55

FULL COVERAGE ARTICULATED DUMP TRUCK HYDRAULICS accumulators hydraulic valves hydraulic cylinders (rams) hydraulic fan motor hydraulic pumps hydraulic tank joysticks electro-hydraulic valves O Rings centre joint seals contamination due to the ingress of water or dirt damage caused by the failure to use the correct specification oil exposed pipes external seals hoses hydraulic cylinder seals hydraulic pipes and connections impact damage improper maintenance and service use of non-approved hydraulic modifications and attachments rubber mountings Doosan Benelux S.A. 01 2016 56

FULL COVERAGE ARTICULATED DUMP TRUCK TRANSMISSION charging pumps, bearings needle / roller bearings couplings gear train and shafts, gears, bushes input and output seals (internal failure) internal seals relief valves oil lubrication pumps inter-axle torque splitter electronic transmission controller transmission control valve and solenoids thrust washers all rubber mounting brackets any failures occurring due to the failure to change the transmission oil at the recommended time or to maintain the oil at the correct level within the transmission assembly damage resulting from the incorrect use of all wheel drive components damage to transmission condition external damage to transmission casing external hoses and fittings failure due to contamination failures due to the use of non-recommended lubrication filter wiring harness transmission discs and plates due to wear limited slip discs and plates due to wear Doosan Benelux S.A. 01 2016 57

FULL COVERAGE ARTICULATED DUMP TRUCK TORQUE CONVERTER housing turbine impeller stator lock-up clutch retarder bearings internal seals all rubber mounting brackets external hoses and fittings failure due to contamination failures due to the use of non-recommended lubrication filter wiring harness lock-up clutch discs and plates due to wear Doosan Benelux S.A. 01 2016 58

FULL COVERAGE ARTICULATED DUMP TRUCK DRIVE AXLES, DRIVE LINES flywheel drive coupling front final drive housing, bearings, shafts and gears front and rear differential rear axle housing, bearings, shafts and gears tandem housing tandem slide bearing tandem housing gear-wheels, bearings, wheel axles and wheel hubs universal joints brake discs and brake plates contamination due to water and / or dirt damage of input and output drive flanges as a result of unit being operated with worn / damaged or seized drive shafts damage resulting from the incorrect use of all wheel drive components damage resulting from the failure to maintain differential breather in clean and serviceable condition damage resulting from the use of solid (foam or water filled) tires external damage to seals failures due to axle and drive line distortion hoses pipes seals Doosan Benelux S.A. 01 2016 59

FULL COVERAGE ARTICULATED DUMP TRUCK BRAKE COMPONENTS accumulator brake pedal lever and mounting linkage parking brake parking brake valve all other brake components brake callipers and seals brake discs / drums / brake packs (wear and heat damage) brake linings brake pads brake shoes damage caused by contamination by oil or water / condensation damage caused by frost damage caused to the parking brake through the machine being operated with the brake still on hoses and fittings Doosan Benelux S.A. 01 2016 60

FULL COVERAGE ARTICULATED DUMP TRUCK STEERING emergency steering electromotor emergency steering pump emergency steering control valve steering unit (orbitrol) hydraulic steering pump relief valves steering cylinders (rams) steering valves hose and fittings ball joints damage resulting from the vehicle becoming bogged down failure of any steering components due to the unit being rolled over and incorrectly recovered steering stops steering wheel track rod ends wear on components resulting from lack of service adjustments and incorrect lubrication methods Doosan Benelux S.A. 01 2016 61

FULL COVERAGE ARTICULATED DUMP TRUCK FRAME front and rear frames castings and casings, providing that the damage has been caused by internal failure only articulated hitch body bolts and clamps damage caused by excessive overloading damage caused by the failure to carry out lubrication at the recommended intervals dust seals failure due to improper maintenance and service failure to maintain recommended chassis inspections resulting in major failure failures due to incorrect operation / use of the machine failures to any pin locations due to a lack a of grease fixing bolts hydraulic hoses and pipes impact damage Doosan Benelux S.A. 01 2016 62

POWER TRAIN CRAWLER EXCAVATOR COMPONENT LIST POWER TRAIN COVERAGE CRAWLER EXCAVATOR The following sections specify which components are covered against failure as defined in the policy, subject to the equipment being fully serviced in accordance with the DOOSAN service instructions and the intervals recommended by DOOSAN. Limits of indemnity and period(s) of cover are detailed in the policy. The following functional areas are detailed below: Engine Hydraulics Undercarriage Front end equipment Doosan Benelux S.A. 01 2016 63

POWER TRAIN CRAWLER EXCAVATOR ENGINE air heater balance assemblies block bushes camshaft and followers Connecting rod connecting rods bearings crankshaft cylinder head cylinder liners external pipes external pump drive gear flywheel head gasket Internal oil seals lubrication pump and drive components including failure of casting assembly main bearings piston pins piston rings Pistons push rods spring and guides timing gears Tappets thrust bearings internal oil seals (internal failure) turbo charger (up to 36 months/6000 hrs from delivery) Valves Doosan Benelux S.A. 01 2016 64

POWER TRAIN CRAWLER EXCAVATOR ENGINE (continued) Air cleaner adjustment of any type including adjustments of engine timing all exhaust components including exhaust manifold contamination deterioration due to age, ingress of dust or foreign matter resulting in engine failure failure due to normal wear and tear failure due to use of fuel of incorrect specification failure resulting from the engine being operated beyond its design speed fan belts filter and filter elements hoses lubricants mountings pre-cleaner stop cables throttle cable valves when burnt and / or pitted Doosan Benelux S.A. 01 2016 65

POWER TRAIN CRAWLER EXCAVATOR HYDRAULICS hydraulic control valves Hydraulic motor swing gearbox swing motors hydraulic pumps accumulators O Rings centre joints centre joint seals contamination due to the ingress of water or dirt damage caused by the failure to use the correct specification oil exposed pipes external seals filters and filter elements flow control valves hoses hydraulic cylinders (rams) hydraulic cylinder seals hydraulic pipes and connections hydraulic tank hydraulic tank breathers impact damage Doosan Benelux S.A. 01 2016 66

POWER TRAIN CRAWLER EXCAVATOR improper maintenance and service use of non-approved hydraulic modifications and attachments. joy sticks pedal valves restriction valves rubber mountings solenoids/electro/hydraulic valves Doosan Benelux S.A. 01 2016 67

POWER TRAIN CRAWLER EXCAVATOR UNDERCARRIAGE travel motors Bearing shafts bottom and top rollers bull gears continuous overloading of the front idlers (tiptoeing) crown wheels damage caused by over speed damage caused by the failure to maintain the final drive casing breathers (where applicable) damage caused by the ingress/contamination by dirt and or water damage resulting from the incorrect mounting/fitting of the drive sprocket/segments damage to the running gear resulting from crushing drive sprockets for wear final drive shafts hoses and clamps idlers input seals (internal failure) impact damage resulting in the failure of a cover component pad bolts for wear pinions piping Doosan Benelux S.A. 01 2016 68

POWER TRAIN CRAWLER EXCAVATOR roller and links seals springs sprockets track covers track frames track links track shoes tracks pins tracks/chains thrust washers Should operational conditions reduce the life of any running gear components, then the premature replacement of these affected components will be at the customer s expense. Doosan Benelux S.A. 01 2016 69

POWER TRAIN CRAWLER EXCAVATOR FRONT END EQUIPMENT arm Boom (mono boom) bucket and bucket teeth bushings consumable parts continuous overloading dust seals damage caused by the failure to carry out recommended inspections failures due to improper maintenance and service failures resulting from incorrect methods of operation fixing bolts and clamps hydraulic hoses and pipes impact damage to cover components linkage lubrication fittings pins side cutters spacers two piece boom) All attachments must be of an approved specification. Doosan Benelux S.A. 01 2016 70

POWER TRAIN WHEELED EXCAVATOR WHEELED EXCAVATOR The following sections specify which components are covered against failure as defined in the policy, subject to the equipment being fully serviced in accordance with the DOOSAN service instructions and the intervals recommended by DOOSAN. Limits of indemnity and period(s) of cover are detailed in the policy. The following functional areas are detailed below: Engine Hydraulics Drive axle, drive line Steering Front end equipment Doosan Benelux S.A. 01 2016 71

POWER TRAIN WHEELED EXCAVATOR ENGINE air heater balance assemblies block bushes camshaft and followers Connecting rod connecting rods bearings crankshaft cylinder head cylinder liners external pipes external pump drive gear flywheel head gasket Internal oil seals lubrication pump and drive components including failure of casting assembly main bearings piston pins piston rings Pistons push rods spring and guides timing gears Tappets thrust bearings internal oil seals (internal failure) turbo charger (up to 36 months/6000 hrs from delivery) Valves Doosan Benelux S.A. 01 2016 72