INSTLL GUIDE DOCUMENT NUMER 0 REVISI DTE 000 FIRMWRE OEM-L(RS)-NI9-[FLCN] HRDWRE FLCN CCESSORIES FLPROG (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. utomotive Data Solutions Inc. 0 EFORE INSTLLTI - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
MODEL YER INSTLL TYPE DT IMMOILIZER YPSS SECURE TKEOVER PRKING LIGHT CTRL X LOCK REMOTE STRT RM OEM LRM DISRM OEM LRM DOOR LOCK DOOR UNLOCK RP SHUTDOWN CTRL DOOR STTUS MITORING TRUNK STTUS MITORING RKE PEDL STTUS MITORING TCHOMETER STTUS MITORING HORN CTRL NISSN MKE VEHICLE LIST - OF utomotive Data Solutions Inc. 0 PGE OF DOC.: #0 000 FETURES Rogue STD key T -
PGE OF DOC.: #0 000 OX CTENTS - OF OX CTENTS WHITE WHITE PIN LCK CNECTOR PIN WHITE CNECTOR MODULE WHITE LUE PROGRMMING UTT 0 PIN LCK CNECTOR PIN WHITE CNECTOR LED F C E D 0 9 LCK PIN WHITE CNECTOR DT CLE PIN LUE CNECTOR DT CLE LCK DT PORT (WELINK, RF, TELEMTIC) WELINK CLE (required accessory sold separately) WELINK CLE MODULE DT PORT COMPUTER US PORT PIN LCK CLE utomotive Data Solutions Inc. 0
PGE OF DOC.: #0 000 COMPENT LOCTOR - OF INTERIOR VIEW DRIVER SIDE VIEW utomotive Data Solutions Inc. 0 PSSENGER SIDE VIEW
PGE OF DOC.: #0 000 utomotive Data Solutions Inc. 0 CNECTOR COLOR CNECTOR TYPE POSITI POLRITY MODULE LOCTI COMPENT LOCTOR CanH ODII White pin 0 lue (DT) t ODII connector CanL ODII White pin Pink (DT) t ODII connector Negative Ignition M Gray 0 pin Yellow t CM Negative Ignition M Gray 0 pin LtPurple/White or Green/White t CM Negative Ignition M Gray 0 pin rown t CM Ignition ODII White pin 0 Yellow (+) t ODII connector ODII White pin White (+) t ODII connector Unlock M9 lack 0 pin Pink t CM Lock M9 lack 0 pin rown t CM Power Liftgate ~ Green 0 pin 0 LtGreen t switch, on lower dash panel Ground ODII White pin 0 lack t ODII connector Negative Starter E9 lack pin 9 Green t CM Hazard Light M Gray 0 pin Yellow t CM - V WIRE COLOR CNECTOR NME YER MODEL Rogue STD key T WIRE DESCRIPTI NISSN MKE TYPE - WIRE CHRT - OF
PGE OF DOC.: #0 000 TYPE - WIRING DIGRM - OF ODII CNECTOR (UNDER DRIVER SIDE DSH) MODULE IGNITI (+) - 0 CNL - CNH - 0 GROUND - 0 F C E DT D 0 GRY/YELLOW (NC) 0 GRY/RED - LOCK OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - UNLOCK OUTPUT 0 LUE/YELLOW - STRTER OUTPUT 0 LUE/RED - GROUND INPUT V (+) - 9 0 CM (LEFT OF STEERING COLUMN) CNECT LY WHEN USING COMPTILE CCESSORY : E9 LCK 0 STRTER - 9 9 0 PINK - IGNITI (+) INPUT 0 PINK/LCK (NC) 0 ORNGE (NC) 0 ORNGE/WHITE - TRUNK OUTPUT 0 ORNGE/LCK (NC) 0 ROWN/YELLOW - CNL 0 ROWN/RED - CNH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/LCK (NC) C CNECT LY WHEN USING COMPTILE CCESSORY LOCK/RM - UNLOCK/DISRM - DIODE N00 DIODE N00 DIODE E IGNITI - IGNITI - : M GRY 0 9 0 IGNITI - POWER LIFTGTE - 0 LUE/WHITE (NC) WHITE (NC) LCK - GROUND RED - V (+) 9 9 0 9 0 9 HZRD LIGHT - 0 WHITE - GROUND INPUT 0 WHITE/RED (NC) 0 WHITE/LCK - IGNITI OUTPUT 0 0 0 0 : M9 LCK 0 9 0 0 9 0 9 N00 D 0 9 WITHOUT COMPTILE CCESSORY POWER LIFTGTE SWITCH : GREEN OR F 9 0 DT CLE COMPTILE CCESSORY WITH COMPTILE CCESSORY. IMPORTNT: SEE THE COMPTILE CCESSORIES PGE FOR DETILS. 0 GREEN/LCK - HOOD STTUS INPUT 0 LUE/LCK (NC) 0 RED/WHITE (NC) WITHOUT OEM HOOD SWITCH: 0 ROWN (NC) INSTLL ND CNECT TO 0 PURPLE/YELLOW (NC) FTERMRKET HOOD SWITCH 0 PURPLE/LCK (NC) FTERMRKET HOOD SWITCH 0 WHITE (NC) 0 LCK/WHITE (NC) 09 GREEN - PRKING LIGHT OUTPUT 0 PURPLE/WHITE (NC) OEM REMOTE REMINS FUNCTIL DURING REMOTE STRT SEQUENCE utomotive Data Solutions Inc. 0
PGE OF DOC.: #0 000 MODULE PROGRMMING PROCEDURE - OF 0 Set ignition to position. CC STRT 0 0 CC 0 CC 0 WRNING: Disconnect power last. Disconnect module from vehicle. Set ignition to position. 09 Connect module to computer and proceed with extended programming. Wait, LED will turn. 0 Connect power first. Connect module to vehicle. Set ignition to position. STRT utomotive Data Solutions Inc. 0 STRT Module Programming Procedure completed. Set ignition to position. CC Wait, LED will flash GREEN rapidly. Set ignition to position. CC Wait, LED will turn solid RED, then solid GREEN for second, then solid RED. STRT STRT 0 Set ignition to position. CC 0 0 STRT Wait, LED will turn solid GREEN for seconds.
VLET MODE PROGRMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within seconds. 0 CC STRT >> PGE OF DOC.: #0 000 To exit valet mode: repeat steps to. Cycle ignition five times [x /] rapidly. ENGINE STRT STOP 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. CC STRT ENGINE STRT STOP 0 Valet Mode Programming Procedure completed. utomotive Data Solutions Inc. 0
PGE 9 OF DOC.: #0 000 MODULE NVIGTI PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to position. 0 TO CCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 0 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 CC STRT TO CCESS THE OPTIS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO CCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MNDTORY: EXIT MODULE NVIGTI. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STRT STOP 0 0 [X] utomotive Data Solutions Inc. 0
PGE 0 OF DOC.: #0 000 [Y] OPTIS [X] MENUS MODULE NVIGTI CHRT: NOTES I Default settings are listed in bold. 0 II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 DISRM/UNLOCK EFORE STRT RELOCK FTER STRT RELOCK FTER SHUTDOWN 0 0 0 0 0 0 0 FORCE UNLOCK LL FIRST PRESS 0 N/ 0 N/ 0 N/ 0 N/ 0 DISLE 0 N/ 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 SEC 0 0 SEC 0 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0- N/ 0 N/ 0 0 N/ FCTORY KEYLESS RS SEQUENCE CFIGURTI 0 09 0-0 Technical Support only 0 0 0 0 [Z] SETTINGS MODULE NVIGTI CHRT - OF MODULE RUN TIME WIT TO STRT DELY N/ *Vehicle will shutdown when a door is opened. utomotive Data Solutions Inc. 0
[X] NUMER OF PRKING LIGHT FLSHES DIGNOSTIC REMOTE STRTER ERROR CODES - OF I WRNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is. 0 Hood is open. II fter a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 0 Glow plug timeout error. REMOTE STRTER ERROR CODES: NOTES utomotive Data Solutions Inc. 0 PGE OF DOC.: #0 000
I II III DURING PROGRMMING DURING REMOTE STRT WITH IGNITI utomotive Data Solutions Inc. 0 DIGNOSTIC TEST MODULE LED STTUS MODULE DIGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN dditional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PGE OF DOC.: #0 000
MODULE RESET PROCEDURE - OF 0 Disconnect all connectors from module except the LCK -PIN connector. 0 Reconnect all connectors. 0 Disconnect the LCK -PIN connector. 0 Repeat programming procedure. 0 PRESS ND HOLD programming button while connecting the LCK -PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELESE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. utomotive Data Solutions Inc. 0 PGE OF DOC.: #0 000
INSTLLTI CHECKLIST - OF PGE OF DOC.: #0 000 CHECKLIST WRNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. Exit vehicle. Installation checklist completed. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. utomotive Data Solutions Inc. 0