according to SAE J1453 and ISO 8434-3 For various tube wall thicknesses in metric or inch dimensions Quick, easy and safe installation Radial installation of the tube Captive/soft seal High nominal pressures VOSS zinc-nickel corrosion protection VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 1 FMV-Schawohl X
Fitting body according to SAE J1453 or ISO 8434-3, respectively Stiffener sleeve, optionally also as soldering sleeve Components Flared tube end Nut according to SAE J1453 or ISO 8434-3, respectively VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 2 FMV-Schawohl X
Fitting body Nut Stiffener sleeve System design Clamped captive soft seal Flared tube end VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 3 FMV-Schawohl X
Radial installation of the tube without having to loosen the opposite support Guided installation Suitable for pressures up to 9,100 PSI or 630 bar, respectively Suitable for tubes with metric and inch dimensions Allows virtually unlimited repeat installations (this only requires checking and, if necessary, replacing the captive soft seal) Best possible corrosion resistance thanks to VOSS zinc-nickel corrosion protection Technical specifications According to SAE J1453 and ISO 8434-3 VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 4 FMV-Schawohl X
Use of various tube wall thicknesses with only one type of fitting body Suitable for tubes with metric and inch dimensions Broad range of products available Wide choice of sealing types and threads Also suitable for directly connecting hoses Stiffener sleeve is also available as soldering sleeve Adaptable to other systems Flexibility VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 5 FMV-Schawohl X
VOSS zinc-nickel surface protection Development of red rust in salt spray test according to ASTM B117 and ISO 9227 only after more than 720 hours Extremely high corrosion resistance, even after handling and installation! Much higher corrosion resistance than a surface protection with a zinc base coat White rust is only observed in the form of a slight gray discoloration, no voluminous white corrosion decomposition products (zinc oxide): "efflorescence" Corrosion protection Verifiably better corrosion resistance than A3C Has been the base coat of choice (zinc-nickel) for many years, now is standard in the European automobile industry Chromium(VI) - free VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 6 FMV-Schawohl X
Short installation and removal times thanks to radial installation Long product life thanks to VOSS zinc-nickel corrosion protection Universally applicable for various tube dimensions Protection cap on the threads to protect them against damage More cost-efficient than soldered joints Economic efficiency VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 7 FMV-Schawohl X
Easy to install and remove Nominal pressures up to 9100 PSI and 630 bar respectively, with a safety factor of 4 O-ring fixation in the adaptor Protection cap on the threads to protect them against damage No "sweating thanks to captive soft seal Excess tightening is virtually impossible Best protection of components against corrosion thanks to VOSS zinc-nickel finish Safety VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 8 FMV-Schawohl X
Male stud unions Connecting unions Bulkhead unions Adjustable male studs with swivel nut Adjustable couplings with swivel nut Adapters Product range Adjustable male stud with lock nut Thread types: BSPP, UNF/UN, NPTF, metric Component parts Female stud and gauge connectors Reducing couplings Sealing types: UN/UNF, NPTF, Profile ring PEFLEX, O-ring, O-ring with retaining ring VOSS Fluid GmbH VFS90 (ORFS) Bördelverschraubungen 06.07.2010 Page 9 FMV-Schawohl X