INSTALLATION INSTRUCTIONS Accessory NIGHT Application 2007 CR-V Publications No. Issue Date SEP. 2006 PARTS LIST Automatic Day/Night Mirror Attachment Kit P/N 08V03-SWA-300 Harness cover set Automatic Day/Night Mirror Kit P/N 08V03-S9A-300B Day/Night mirror Automatic Day/Night mirror harness Operating Instructions 9 Wire ties 4 EPT sealers TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Socket Isopropyl alcohol Shop towel Diagonal cutters T-20, T-25 Torx bit Needle nose pliers Steel wire Clip Ground bolt Honda Access Corp. 2006 08V03-SWA-3000-93 1 of 9
ILLUSTRATION OF THE DAY/ IN- STALLED ON THE 3. Carefully remove the right and left map light lens from the roof console (four tabs for each lens). DAY/NIGHT ROOF CONSOLE TABS (4) TABS (4) FUSE BOX 6312070B LEFT MAP LIGHT LENS RIGHT MAP LIGHT LENS 6308150Y INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safety add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down radio station presets. 2. Disconnect the negative cable from the battery. 4. Remove the roof console (four bolts and unplug the vehicle connectors). ROOF CONSOLE SILVER BOLTS (2) BLACK BOLTS (2) 6313021Y 2 of 9 Honda Access Corp. 2006
5. Remove the cover from the left sunvisor (four retaining tabs). 6. Remove the two T-25 Torx screws, pull out the left sun visor, and remove the sunvisor. 8. Remove the cover from the mirror (two retaining tabs). 9. Lift up the mirror while pulling the base, and remove the mirror. TABS (2) COVER Lift up. TABS (4) BASE Pull. COVER LEFT SUNVISOR TORX SCREWS (2) 6311130B 7. Using a flat-tip screwdriver, remove the right and left sunvisor holders. BASE 6823040B LEFT SUNVISOR HOLDER 10. Using a flat-tip screwdriver, remove the two caps from the left front grab rail. FLAT-TIP SCREWDRIVER Push. RIGHT SUNVISOR HOLDER FLAT-TIP SCREWDRIVER Turn. SUNVISOR HOLDERS (2) 6308170Y CAPS (2) GRAB RAIL GRAB RAIL CAP 6311161B Honda Access Corp. 2006 3 of 9
11. Using a needle nose pliers, remove the left front grab rail (two clips). GRAB RAIL S (2) 12. Take off the front door opening seal. Push the A-pillar trim into the vehicle body by striking the top of the A- pillar trim in the area marked SIDE CURTAIN AIR- BAG with your hand perpendicularly to the vehicle. Then, remove the clip. TAB Collapsed. Remains on the vehicle panel. NEEDLE NOSE PLIERS TAB Tap. BODY PIN Comes off from the clip. Pull. GRAB RAIL 6311170B BODY DOOR OPENING SEAL Pushed deep behind the vehicle panel. BODY PART MARKED AS SIDE CURTAIN AIRBAG A-PILLAR TRIM Tap at right angles to the vehicle. Tap with a hand. 6629120B 4 of 9 Honda Access Corp. 2006
13. Remove the door opening seal from around the left A-pillar. Remove the left A-pillar trim (two clips). 15. Take off the front door opening seal. Remove the left kick panel (two clips). S (2) S (2) DOOR OPENING SEAL DOOR OPENING SEAL LEFT A-PILLAR TRIM 6311181B LEFT KICK PANEL 6303100B 14. Remove the left front door sill trim (three clips). S (3) 16. Plug the automatic day/night mirror harness 6-pin connector into the 6-pin connector opening of the fuse box. FUSE BOX 6-PIN OPENING POSITION 6-PIN OPENING of the FUSE BOX FUSE BOX FUSE BOX DOOR SILL TRIM 6303090B 6-PIN 6312022B Honda Access Corp. 2006 5 of 9
If another accessory is already plugged into the 6-pin connector opening of the fuse box, remove the dummy connector from the 6-pin connector taped to the automatic day/night mirror harness. Plug the 6-pin connector from the other accessory harness into the 6-pin connector from the automatic day/night mirror harness you just unplugged and plug the automatic day/night mirror harness into the 6-pin connector opening of the fuse box. 18. Route the automatic day/night mirror harness behind fuse box. FUSE BOX 6-PIN OPENING of the FUSE BOX OTHER ACCESSORY 6-PIN 6-PIN DUMMY 6627090B 19. Secure the automatic day/night mirror harness to the vehicle harness with the two wire ties in the areas shown. 6312030B 17. Attach a piece of steel wire to the automatic day/ night mirror harness, and route it to the left front pillar trim opening. PILLAR TRIM OPENING STEEL WIRE WIRE TIE FUSE BOX WIRE TIE 6312042B FUSE BOX NIGHT 6627080B 6 of 9 Honda Access Corp. 2006
20. Remove the vehicle bolt from the fuel lid opener. Attach the automatic day/night mirror harness ground terminal with the ground bolt. 22. Route the automatic day/night mirror harness upper the headliner from the left A-pillar to the middle side of the vehicle. FUSE BOX GROUND BOLT BOLT (Not used.) FUEL LID OPENER NIGHT GROUND TERMINAL 6823030B HEADLINER LEFT A-PILLAR 7-PIN 6311191B 21. Remove the steel wire. Route the automatic day/ night mirror harness along the vehicle harness as shown. Secure the day/night mirror harness to the vehicle harness with a wire tie (adjust the tape of the day/night mirror harness with the wire tie). Secure the day/night mirror harness to the vehicle harness with the three wire ties. TAPE 23. Plug the automatic day/night mirror harness 7-pin connector into the day/night mirror. 24. Install the day/night mirror on the mirror base, then tighten the T-20 Torx screw installed the day/night mirror. 7-PIN WIRE TIE BASE LEFT A- PILLAR WIRE TIE PILLAR TRIM OPENING 6823010B TORX SCREW Up. 6311202B Honda Access Corp. 2006 7 of 9
25. Using isopropyl alcohol, thoroughly clean the areas where the EPT sealer will attach. Secure the automatic day/night mirror harness to the headliner with three EPT sealers. 26. Secure the automatic day/night mirror harness to the vehicle harness with the four wire ties loosely secure in step 21. 28. Remove the vehicle clip that remains on the left A-pillar. 29. Check that the left A-pillar trim and the pin are not damaged, and install the clip on the pin. Remove. EPT SEALER LEFT A-PILLAR LEFT A-PILLAR TRIM PIN HEADLINER 6305010H 6311211B 27. Install the harness cover to the automatic day/night mirror and the headliner as shown. HEADLINER 30. Position the clip at right angles to the hole in the left A-pillar. Install the clip by lightly pushing the left A-pillar trim at the part marked as SIDE CURTAIN AIR- BAG. Check that the airbag is not pinched with the clip. Take care not to push the left A-pillar trim excessively. LEFT A-PILLAR COVER PANEL 6312062B PART MARKED AS SIDE CURTAIN AIRBAG LEFT A-PILLAR TRIM 6519020Y 8 of 9 Honda Access Corp. 2006
31. Check that all wire harnesses are routed properly and all connectors are plugged in. 32. Reinstall all removed parts. 33. Reconnect the negative cable to the battery. 34. Enter the customer s audio and navigation system (if equipped) anti-theft codes, and reset the XM radio presets. 35. Reset the clock. NOTE: check the operation of the automatic day/night mirror according to the Operating Instructions supplied. Store the Operating Instructions in the globe box. Honda Access Corp. 2006 9 of 9
2007 CRV SPARE PARTS ACCESSORY PART REPLACEMENT REPLACEMENT DESCRIPTION NUMBER PART DESCRIPTON PART NUMBER Auto D/N Mirror Attach 08V03-SWA-100 Clip 91561-SJK-J01 Bolt, Earth 6x16 90148-SE0-003 Set, Harness Cover 08V03-SWA-1M005