MONOBLOCK DIRECTIONAL CONTROL VALVES
CONTENTS: RM0...... RM5...... RM40P...... RM80...... RMD90...... MRP70... Page 1/19&/19 /19...5/19 6/19...10/19 11/19...15/19 16/19&17/19 18/19&19/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM0 GENERAL DESCRIPTION Document: MDCV-1-Sept 015 Hydraulic valve RM0 provides change of fluid flow direction, hydro-systems pressure restriction, pump unloading in neutral position of the spools. The valve RM0 is designed to be integrated in hydraulic systems of Mobile and Industrial Machines. The valve assembly consists of: A body with integrated relief and check valve, spool, control and spring-centering group of the spool. The valve RM0 provides direct passing of the flow from the pump line to the tank at neutral position (open center). Options closed centre and carry over are possible with additional adapters. There are different control options: spring centering in neutral position, detent, automatic kick-out, hydraulic and electro-hydraulic control. TECHNICAL DATA Rated flow 0 l/min Max. pressure P=50 bar; T=0 bar; A,B= 50 bar Spool stroke ±,5 mm Working temperature range -15...+80 C Working liquid hydraulic oil HLP DIN5154 Liquid viscosity 15...00cSt Nominal filtration ISO4406: 19/16 (recommended filter element - 0,05mm mesh) Internal leakage at 10 bar, o t=40 C and viscosity 46cSt max. 8cm³/min; max cm³/min (special version) Actuating force less than 150N Weight 1,7kg DIMENSIONS 1/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM0 ORDERING CODE RM0 / N / Q / 1 CL A 1 E1 / R / P1T1 / G / N with check valve - omit without check valve - N application N normal T tropical standard port threads P1, T1, T P, A, B G G/8 -A G1/4 -A relief valve setting range 5...50bar. (example of required settings 180bar.) shut-off plug installed Q Q180 K P1T1 P1T PT1 used connection ports P1 and T1 P1 and T P and T1 PT P and T spools hydraulic power output 1 R W open center (port P connected to T - short plug) closed center (port T1 plugged - long plug) C carry over (T1 - with power beyond sleeve) 4 1 spool control micro switch: max. current/voltage - 5A/50V AC protection - IP67 contact configuration 5* DIN 4650-A 6 4 5 omit without microswitch 7 6 E1 8* * The scheme (spool code 5, 8) needs special body with extra machining and modified cap (C, CL, CLO control) for spool control code 5. 7 lever position A at port side A(standard) B at port side B E E without standard hand lever C o with standard hand lever CL with standard hand lever at 180 CLO with cable control H without lever, with dust-proof plate Z 70 Cables, single levers and joystick controls - on request /19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM5 GENERAL DESCRIPTION Hydraulic valve RM5 provides change of fluid flow direction, hydro-systems pressure restriction, pump unloading in neutral position of the spools. The valve RM5 is designed to be integrated in hydraulic systems of Mobile and Industrial Machines. The valve assembly consists of: A body with integrated relief and check valve, spool, control and spring-centering group of the spool. The valve RM5 provides direct passing of the flow from the pump line to the tank at neutral position (open center). There are different control options: spring centering in neutral position, detent, automatic kick-out, hydraulic and electro-hydraulic control. TECHNICAL DATA Rated flow 5 l/min Max. pressure P=50 bar; T=50 bar; A,B= 00 bar Spool stroke ±6 mm Working temperature range -15...+80 C Working liquid hydraulic oil HLP DIN5154 Liquid viscosity 15...00cSt Nominal filtration ISO4406: 19/16 (recommended filter element - 0,05mm mesh) Internal leakage at 10 bar, o t=40 C and viscosity 46cSt max. 8cm³/min; max cm³/min (special version) Actuating force less than 00N Weight,kg DIMENSIONS RM5/Q/1CLA1/G/N /19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM5 RM5EHI / N / Q / 1 CL A 1 E1 / G / N ORDERING CODE type of control without control ON-OFF internal electro-hydraulic ON-OFF external electro-hydraulic ON-OFF electropneumatic ON-OFF hydraulic ON-OFF pneumatic omit EHI EHE EPC HC PC 1 4 5 spool control standard port threads P, T, A, B M M18x1,5-6H G G/8 -A N T application normal tropical micro switch: max. current/voltage - 5A/50V AC protection - IP67 contact configuration DIN 4650-A with check valve - omit without check valve - N relief valve setting range 5...50bar. (example of required settings 180bar.) shut-off plug installed Q Q180 K 6 7 9 10 11* omit E1 E without microswitch spools Adjustment range of automatic kick-out feature - 60...180bar E 1 4* 5* 6 1 1 14 15 16 17 SD1 SD10 0-1 1VDC 0-4 4VDC 0-11 110VRAC 0-0VRAC 0-1 1VDC 0-4 4VDC 0-11 110VRAC 0-0VRAC spool control ON-OFF EHI & EHE ON-OFF EPC ON-OFF HC & PC 7 8* A B lever position at port side A(standard) at port side B * The kit (spool control code 11) needs special spool. 9* 10* * The scheme (spool code 4, 5, 8, 9 and 10) needs special body with extra machining. C CL CLO CLR see page / CLS CP H Z 4/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM5 OPERATION CONTROL without standard hand lever C o with standard hand lever at 180 CLO with standard hand lever CL with stroke (flow) limiter CLR with limit switch CLS with cable control H Cables, single levers and joystick controls - on request with protection cap CP without lever, with dust-proof plate Z 5/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM40P GENERAL DESCRIPTION Hydraulic valve RM40P provides change of fluid flow direction, hydro-systems pressure restriction, pump unloading in neutral position of the spools. The valve RM40P is designed to be integrated in hydraulic systems of Mobile and Industrial Machines. The valve assembly consists of: A body with integrated relief and check valves, spools, control and spring-centering group of the spools. The valve RM40P provides parallel distribution of the working liquid and direct passing of the flow from the pump line to the tank at neutral position (open center). Options closed centre and carry over are possible with additional adapters. There are different control options: spring centering in neutral position, detent, automatic kick-out, hydraulic and electro-hydraulic control. TECHNICAL DATA Rated flow 40 l/min Max. pressure P=50 bar; T=50 bar; A,B= 00 bar Spool stroke ±6 mm Working temperature range -15...+80 C Working liquid hydraulic oil HLP DIN5154 Liquid viscosity 15...00cSt Nominal filtration ISO4406: 19/16 (recommended filter element - 0,05mm mesh) Internal leakage at 10 bar, o t=40 C and viscosity 46cSt max. 8cm³/min; max cm³/min (special version) Actuating force less than 00N DIMENSIONS RM40P/0/Q/x/1CLA1/R/P1T1/G/N 6/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM40P ORDERING CODE RM40PEHI / 0 / Q / 1 CL A 1 E1 / R / P1T1 / G / N * * parallel connection for RM40 - omit type of control without control On-Off internal electro-hydraulic On-Off external electro-hydraulic On-Off electropneumatic On-Off hydraulic omit EHI EHE EPC HC On-Off pneumatic PC common check valve with check valve 0 for RM40 - omit without check valve N 1 R W C standard port threads P1, P A, B T1, T, N M Mx1,5-6H M18x1,5-6H Mx1,5-6H G G1/ -A G/8 -A G1/ -A U 7/8-14UNF-B /4-16UNF-B 7/8-14UNF-B G1/ G1/ -A hydraulic power output open center (port N connected to T - short plug) closed center (port N plugged - long plug) carry over (port N - with power beyond sleeve) spool control P1T1 P1T PT1 PT application N T P1 and T1 normal tropical used conn. ports P1 and T P and T1 P and T micro switch: max. current/voltage - 5A/50V AC protection - IP67 contact configuration number of the spools for RM40 - omit relief valve setting range 5...50bar (example of required settings 180bar) shut-off plug installed Q Q180 K 4 5 6 omit E1 without microswitch DIN 4650-A spools 7 E 1 8 9 E 10 spool control 4 11* Adjustment range of automatic kick-out feature - 60...180bar 0-1 1VDC 0-4 4VDC 0-11 110VRAC 0-0VRAC ON-OFF EHI & EHE 5 6 7 1 1 14 15 0-1 1VDC 0-4 4VDC 0-11 110VRAC 0-0VRAC ON-OFF HC & PC ON-OFF EPC 8* 16 SD1 9 10* 11* * The scheme (spool code 8, 10 and 11) needs special body with extra machining. 17 C CL CLO CLR see page /5 CLS CP H Z J... see page 4/5 A B SD10 lever position * The kit (spool control code 11) needs special spool. at port side A (standard) at port side B ** Repeat for each spool. In case of identical spools example ordering code is: RM40P / 0 / Q / x / 1CL A1 / R / P1T1 / G / N 7/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM40P OPERATION CONTROL without standard hand lever C o with standard hand lever at 180 CLO with standard hand lever CL with stroke (flow) limiter CLR with limit switch CLS with cable control H Cables, single levers and joystick controls - on request with protection cap CP without lever, with dust-proof plate Z 8/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM40P OPERATION CONTROL Working scheme by assembly on the side of threaded ports A (standard) J1... J... J4... joystick with standard hand lever joystick without standard hand lever : J1L ; JL ; JL ; J4L : J1 ; J ; J ; J4 M10 9/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM40P RM40PEHI/0/Q/x/1CLA0-4/R/P1T1/G/N On/Off electrohydraulic control (internal) operating features: Pilot pressure - 10...50 bar Max. pilot flow - 8 l/min Filtration - 5 mm Coil - 18W, duty cycle ED 100% Voltage options - 1V DC, 4V DC, 110V RAC, 0V RAC Integrated back pressure valve RM40PEHE/0/Q/x/1CLA0-4/R/P1T1/G/N On/Off electrohydraulic control (external) operating features: Pilot pressure Pp - 10...50 bar Max. pilot flow - 8 l/min Filtration - 5 mm Coil - 18W, duty cycle ED 100% Voltage options - 1V DC, 4V DC, 110V RAC, 0V RAC Pp, Tp - G1/4 10/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM80 GENERAL DESCRIPTION Hydraulic valve RM80 provides change of fluid flow direction, hydro-systems pressure restriction, pump unloading in neutral position of the spools. The valve RM80 is designed to be integrated in hydraulic systems of Mobile and Industrial Machines. The valve assembly consists of: A body with integrated relief and check valves, spools, control and spring-centering group of the spools. The valve RM80 provides parallel distribution of the working liquid and direct passing of the flow from the pump line to the tank at neutral position (open center). Options closed centre and carry over are possible with additional adapters. There are different control options: spring centering in neutral position, detent, automatic kick-out, hydraulic and electro-hydraulic control. TECHNICAL DATA Rated flow 80 l/min Max. pressure P=50 bar; T=50 bar; A,B= 00 bar Spool stroke ±7 mm Working temperature range -15...+80 C Working liquid hydraulic oil HLP DIN5154 Liquid viscosity 15...00cSt Nominal filtration ISO4406: 19/16 (recommended filter element - 0,05mm mesh) Internal leakage at 10 bar, o t=40 C and viscosity 46cSt max. 8cm³/min; max cm³/min (special version) Actuating force less than 80N DIMENSIONS RM80P//Q/x/1CLA1/R/P1T1/G/N 11/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM80 ORDERING CODE RM80PEHI / / Q / 1 CL A 1 E1 / R / P1T1 / G / N * * type of connection for RM80 Parallel Series* Tandem (P+S)* type of control without control On-Off internal electro-hydraulic On-Off external electro-hydraulic On-Off electropneumatic On-Off hydraulic omit * The scheme (connection type S and T) needs special body. P S T omit EHI EHE EPC HC On-Off pneumatic PC 1 R W C standard port threads P1, P, A, B T1, T, N M Mx1,5-6H M6x1,5-6H G G1/ -A G/4 -A U 7/8-14UNF-B 1 1/16-1UN-B hydraulic power output open center (port N connected to T - short plug) closed center (port N plugged - long plug) carry over (port N - with power beyond sleeve) spool control application N T P1T1 P1T PT1 PT normal tropical used conn. ports P1 and T1 P1 and T P and T1 P and T micro switch: max. current/voltage - 5A/50V AC protection - IP67 contact configuration number of the spools for RM80 - omit relief valve setting range 0...00bar Q (example of required settings 180bar) Q180 shut-off plug installed K 4 5 6 omit E1 without microswitch DIN 4650-A spools 7 E 1 9 11* E 4 1 1 Adjustment range of automatic kick-out feature - 60...180bar 0-1 1VDC 0-4 4VDC 0-11 110VRAC 0-0VRAC spool control ON-OFF EHI & EHE 5 6 7 14 15 16 17 0-1 1VDC 0-4 4VDC 0-11 110VRAC 0-0VRAC ON-OFF HC & PC ON-OFF EPC 8* * The kit (spool control code 11) needs special spool. 9* 10 * The scheme (spool code 8 and 9) needs special body with extra machining. C CL CLO CLR see page /5 CLS CP H Z J... see page 4/5 A B lever position at port side A (standard) at port side B ** Repeat for each spool. In case of identical spools example ordering code is: RM80 / / Q / x / 1CL A1 / R / P1T1 / G / N 1/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM80 OPERATION CONTROL without standard hand lever C o with standard hand lever at 180 CLO with standard hand lever CL with stroke (flow) limiter CLR with limit switch CLS with cable control H Cables, single levers and joystick controls - on request with protection cap CP without lever, with dust-proof plate Z 1/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM80 OPERATION CONTROL Working scheme by assembly on the side of threaded ports A (standard) J... J1... J... J4... joystick with standard hand lever joystick without standard hand lever : J1L ; JL ; JL ; J4L : J1 ; J ; J ; J4 M10 14/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RM80 RM80PEHI/4/Q/4x/1CLA0-4/R/P1T1/G/N On/Off electrohydraulic control operating features: (internal) Pilot pressure - 10...50 bar Max. pilot flow - 8 l/min Filtration - 5 mm Coil - 18W, duty cycle ED 100% Voltage options - 1V DC, 4V DC, 110V RAC, 0V RAC Integrated back pressure valve 15/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RMD90 GENERAL DESCRIPTION The directional control valve RMD90 provides a change of fluid flow direction in the channels of the hydraulic system. Valve RMD90 is designed for mounting in the hydraulic systems of the mobile and industrial machines. TECHNICAL DATA Weight 5.7kg Nominal flow 90 l/min Maximal flow 150 l/min Nominal pressure 16 MPa Maximal pressure 0 MPa Working stroke of the spool ±8 mm Spool leakage at p=100bar o t=40 C and viscosity 6cSt 5 cm /min Working fluid-hydraulic oil with parameters: viscosity - 15...00cSt recommended viscosity - 0...80cSt o temperature - -0...+80 C degree of filtration - 0,05mm DIMENSIONS 16/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE RMD90 ORDERING CODE RMD90-1 DL 1 G Double acting, position, 4 way A and B blocked in neutral 1 G K P, T, A, B G/4 -A K/4-14 GOST6111-5 (/4-14NPT) Double acting, position, 4 way A, B and P to tank in neutral 1 Spring return to neutral Double acting, position, 4 way A and B to tank in neutral Detent in position 1 and Lever : with lever DL without lever D Detent in three positions 17/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE MRP70 GENERAL DESCRIPTION 1. The valve type MRP 70 incorporates the features of a 4-way directional control valve, an adjustable full range pressure compensated by-pass type flow control valve and a pilot operated pressure relief valve all in one compact package.. Less fittings and plumbing, eliminates leakage points.. Fine positive metering is possible in either direction with one manually adjustable, infinitely variable lever controlling both direction and amount of flow. Amount of flow is proportional to movement of the lever. 4. Flow is constant regardless of pressure variations, thus flow out the work port remains smooth and constant regardless of changes in load conditions. 5. An externally adjustable pilot relief is standard. 6. Friction detent (Friction positioner kit). Hydraulic scheme: Rated flow l/min (US GPM) 70 (18) Rated pressure bar (PSI) 10 (000) Standard port size: DATA Inlet & outlet work ports A & B TECHNICAL DATA Working liquid - hydraulic oils with parameters: -viscosity mm /sec (cst) 15...00 -recommended viscosity mm /sec (cst) 0...80 -temperature o o C ( F) -0...+80 (-4...+176) -degree of filtration mm (in) -4 0.05 (9.8 10 ) Leakage at p=100bar cc/min 15 t=40oc ; 6cSt UNIT BSP BSP VALUE/RANGE /4 ½ 18/19
MONOBLOCK DIRECTIONAL CONTROL VALVE TYPE MRP70 PERFORMANCE CURVE 100 Neutral Flow Pressure Drop CONDITIONS:? P=f(Q) 6 cst oil viscosity T=40 C(104 F) 80 60 40 0 0 0 5 10 15 0 Flow [GPM] In this curve the pressure difference between the inlet and outlet is shown. DIMENSIONS All dimensions are in mm (in). A 54(.1) 85(.1) 81(.15) Pressure[PSI] 100(.9) 185(7.1) A 19/19
BULGARIA JOINT-STOCK COMPANY BULGARIA, 6100 KAZANLAK, 45 STOLETOV Str. Tel.:+59/41/6 9, +59/41/61, Fax:+59/41/6 0, +59/41/6 14 E-mail:caproni@caproni.bg, WEB:http://www.caproni.bg