G11 FAN LIGHT WINDOWS G11.11 50141 FOR BOTTOM HUNG WINDOWS 01.12.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com
CONTENTS 1. General characteristics... G11.11.03 2. Base set n 50141R or L... G11.11.06 3. Base set n 50141KR or KL for small windows... G11.11.07 4. Horizontal centre locking sets... G11.11.08 5. Vertical centre locking sets... G11.11.09 6. Selection of rods for remote control system 50141... G11.11.10 7. Selection of rods for remote control system 50141K... G11.11.13 8. Keep positions for remote control system 50141...G11.11.14 9. Keep positions for remote control system 50141K... G11.11.17 10. Special situations... G11.11.18 11. Hinge n 26140-750... G11.11.18 12. Drilling jig - installation handle, track - preparations... G11.11.19 13. Installation order with base set n 50141... G11.11.21 14. Installation order with base set n 50141K... G11.11.22 15. Sill transmission with cable n 50102-35-... G11.11.23 15.1. Application possibilities G11.11.24 15.2. Vent weight G11.11.24 15.3. Installation order G11.11.25 16. Order tables... G11.11.27 16.1. Standard windows G11.11.27 16.2. Small windows G11.11.27 17. General information... G11.11.28 G11.11.02
1. General characteristics New concealed clampable remote control system Invisitop 50140 for hopper windows, based on the Chrono technology. The remote control system is LEFT HAND or RIGHT HAND and suitable for installation on aluminium windows. The entire system with exception of the lever and the connection piece, is mounted concealed in the vent eurogroove, resulting in greatly improved aesthetics. G11.11 The same connection rods in synthetic material of the Chrono system are connected to the corner transmission and the link arm and are provided with locking points as standard, which serve as additional horizontal centre locking points for higher and wider windows to get sufficient wind and water tightness. The wind and water tightness complies with the higher STS standards. The link arm can easily be disconnected to mount the system and to be able to clean the window on the outside: slide knob against the spring pressure pull the arm downwards to disconnect Left hand window Right hand window Connection Disconnection All parts of the remote control system are manufactured from non-corroding materials. Finish: handle and cover sections in aluminium anodised or polyester powder coated in a choice of more than 450 RAL colours; the U-shaped cover sections are available in lengths of 3 or 6 m. Bronze or black anodised in 3 m lengths only; rods ø8 mm in aluminium anodised, steel zinc plated or stainless steel and available in lengths of 1, 2 or 3 m; screws in stainless steel. Operating devices: handle fixed winder with vertical winding gear loose winder with vertical winding gear The operating force always remains under 100 N, as described in the standard. When required, the set can be combined with the cable transmission. G11.11.03
The system is suitable for profiles with the following dimensions: necessary space on the frame section for mounting the lever handle: 20.5 mm. frame groove 14/18 mm and frame groove 10/14 mm. The Invisitop 50141 can t be used in combination with the concealed hinges (Invision Pro and Invision Go). Frame groove 14/18 mm Frame groove 10/14 mm A 14 ± 0.5 10 ± 0.5 B 18 ± 0.5 14 ± 0.5 Size range for base set n 50140: vent width: 500-3600 mm (Fh<1200 mm) vent width: 650-1800 mm (Fh>1200 mm) vent height: 400-2400 mm vent weight: max. 80 kg opening: ±170 mm Size range for base set n 50140K (small windows): vent width: 500-2400 mm vent height: 250-400 mm vent weight: max. 20 kg opening: ±110 mm Maximum vent weight depending on the vent height and the profile depth: Vent height Maximum vent weight With sill transmission Glass position (X-value) > 1000 mm 80 kg 60 kg 10-60 mm 800-1000 mm 80 kg 60 kg 20-45 mm 800-1000 mm 60 kg 50 kg 10-60 mm 600-800 mm 60 kg 50 kg 10-30 mm 600-800 mm 50 kg 40 kg 10-50 mm 600-800 mm 40 kg 30 kg 10-60 mm 400-600 mm 30 kg 22 kg 10-60 mm 250-400 mm 20 kg 15 kg 10-60 mm G11.11.04
Minimum vent height: The minimum vent height depends on the profile design. The rotation curve is determined when using hinges n 26140-750. A clearance of 1 mm is included in the zone with required free space. Zone with required free space for the Invisitop link arm n 50140-550. When tilting the vent, no profile detail or part may enter the zone of 9.8 mm below the frame groove. Note: you can always send us your profile drawings to check. G11.11.05
2. Base set n 50141R or L Vent width Fb = 500-1200 mm Vent height Fh = 400-1200 mm (leave out when Fb<600 mm) Base set n 50141R or L = Handle n 7800-200 + N 50140R or L 2 30140-800 keep 1 50100-40 locking point 1 50100-500-1 corner transmission 1 50100-530 clip connection piece 1 50100-531 clip corner transmission 1 50100-550-2R/L vent part of link arm 1 50100-710R/L connection piece 1 50140-550-1R/L frame part of link arm 1 50140-710R/L drive piece 1 50140-711 guiding piece 1 50140-712-1 cover profile 1 50140-712-2 cover 3 M6x6 DIN 916 screw 4 M5x14 DIN 7500M k7.5 screw 2 ø4.2x16 DIN 7504P screw Accessories m L7700-110 cover: 3 or 6 m m 7800-100-. rod: 1 m or 7800-101-. or 2 m or 3 m or 7800-102-. 7800-150 clip 26140-750 hinge 35000-... rods aluminium stainless steel steel zinc plated Notes: When ordering please indicate quantity of cover sections and rods. Number of clips depends on the position of the handle. Number of hinges in accordance with the vent width. Rods: see page G11.11.10. The screws for the clips and the handles are not included. or or G11.11.06
3. Base set n 50141KR or KL for small windows Vent width Fb = 500-1200 mm Vent height Fh = 250-400 mm G11.11 (leave out when Fb<600 mm) Base n 50141KR or KL = Handle n 7800-200K + N 50140KR or KL 2 30140-800 keep 1 50100-40 locking point 1 50100-500-1 corner transmission 1 50100-530 clip connection piece 1 50100-531 clip corner transmission 1 50100-550-2KR/KL vent part of link arm 1 50100-710R/L connection piece 1 50140-550-1R/L frame part of link arm 1 50140-710R/L drive piece 1 50140-711 guiding piece 1 50140-712-1 cover profile 1 50140-712-2 cover 3 M6x6 DIN 916 screw 4 M5x14 DIN 7500M k7.5 screw 2 ø4.2x16 DIN 7504P screw Accessories m L7700-110 cover: 3 or 6 m m 7800-100-. rod: 1 m or 7800-101-. or 2 m or 3 m or 7800-102-. 7800-150 clip 26140-750 hinge 35000-... rods aluminium stainless steel steel zinc plated Notes: When ordering please indicate quantity of cover sections and rods. Number of clips depends on the position of the handle. Number of hinges in accordance with the vent width. Rods: see page G11.11.13. The screws for the clips and the handles are not included. or or G11.11.07
4. Horizontal centre locking sets Vent width (Fb) = 1201-1800 mm link arm 1 50141R or L or 50141KR or KL + 1 30140-800 keep Vent width (Fb) = 1801-2400 mm link arm 1 50141R or L or 50141KR or KL 30140-800 + 1 30140-800 keep Vent width (Fb) = 2401-3000 mm link arm 1 50141R or L or 50141KR or KL 30140-800 30140-800 + 1 50140-550R or L link arm 1 35000-165 rod Vent width (Fb) = 3001-3600 mm link arm 2 50141R or L or 50141KR or KL 30140-800 30140-800 50140-550R or L 35000-165 + 1 30140-800 keep G11.11.08
5. Vertical centre locking sets Vent height (Fh) = 1201-1800 mm (vent width (Fb) > 650 mm) G11.11 Note: 50141R or L or 50141KR or KL + 1 50100-500 corner transmission 2 30140-800 keep The top keep is eliminated and the locking point is moved to the vertical side. Vent height (Fh) = 1801-2400 mm (vent width (Fb) > 650 mm) 50141R or L or 50141KR or KL 50100-500 2x 30140-800 + 2 30140-800 keep G11.11.09
6. Selection of rods for remote control system 50141 Vent width (Fb) = 500-2400 mm Vent height (Fh) = 400-1200 mm The system consists of 11 transmission rods in synthetic material with different lengths: 35000-100, 35000-150,.... The adjustment range of each rod is 50 mm. Important: mount the rods in the same order as indicated in the table. G11.11.10
Vent width (Fb) = 650-1800 mm Vent height (Fh) = 1200-1800 mm Vent width (Fb) = 650-1200 mm Vent height (Fh) = 1800-2400 mm The system consists of 11 transmission rods in synthetic material with different lengths: 35000-100, 35000-150,.... The adjustment range of each rod is 50 mm. Important: mount the rods in the same order as indicated in the table. G11.11.11
Vent width (Fb) = 2400-3600 mm Vent height (Fh) = 400-1200 mm link arm 2 link arm 1 Attention: Already in order table! The system consists of 11 transmission rods in synthetic material with different lengths: 35000-100, 35000-150,.... The adjustment range of each rod is 50 mm. Important: mount the rods in the same order as indicated in the table. G11.11.12
7. Selection of rods for remote control system 50141K Vent width (Fb) = 500-2400 mm Vent height (Fh) = 250-400 mm The system consists of 11 transmission rods in synthetic material with different lengths: 35000-100, 35000-150,.... The adjustment range of each rod is 50 mm. Important: mount the rods in the same order as indicated in the table. G11.11.13
8. Keep positions for remote control system 50141 Vent width (Fb) = 500-2400 mm Vent height (Fh) = 400-1200 mm G11.11.14
Vent width (Fb) = 650-1800 mm Vent height (Fh) = 1200-1800 mm Vent width (Fb) = 650-1200 mm Vent height (Fh) = 1800-2400 mm G11.11.15
Vent width (Fb) = 2400-3600 mm Vent height (Fh) = 400-1200 mm G11.11.16
9. Keep positions for remote control system 50141K Vent width (Fb) = 500-2400 mm Vent height (Fh) = 250-400 mm G11.11 G11.11.17
10. Special situations Vent width (Fb) = 500-550 mm For windows with vent width (Fb) from 500 to 550 mm, the connection piece of the link arm must be cut as indicated on the drawing. Vent height (Fh) = 250-300 mm For windows with vent height (Fh) from 250 to 300 mm, the connection piece must be cut on the indication line as indicated on the drawing. 11. Hinge n 26140-750 26140-750 1 26140-760-1 frame part 1 35000-760-1 vent part 2 30140-760-3 cap 2 35000-760-3 screw DIN 965 M5x8 1 4200-150.3 hinge pin 1 26000-750-4 clamping plate G11.11.18
12. Drilling jig - installation handle, track - preparations Drilling jig n 50141-950 Installation track for connection piece G11.11 Handle Track n 50140-711 Instructions Left hand window Right hand window Track n 50140-711: Position the jig in the lower frame corner and drill 4 holes ø4,2 mm at position A. Handle: Position the jig at the intended position against the frame and drill 3 holes ø3,3 mm at position B (BR = right; BL = left). G11.11.19
Temporary handle Handle directly Handle on installation when below the window the window mounting the perimeter locking set short temporary rod When the handle is separate from the window. When using another method of operation: winder,.... It is necessary to open and close the window during installation of the perimeter locking set. Therefore this temporary solution is necessary before the final assembly. The temporary handle must be fitted so that it is fixed in relation to the frame. Connection piece Connection piece set 50140 set 50140K Hinge G11.11.20
13. Installation order with base set n 50141 G11.11 Keep 500-600 601-650 651-1200 1201-1800 1801-2400 2401-3000 3001-3600 400-1200 19 15, 19 15, 19 15, 17, 19 1201-1800 - - 1801-2400 - - 11, 13, 15, 19 11, 12, 13, 14, 15, 19 11, 13, 15, 17, 19 15, 16, 18, 19 15, 16, 18, 19 - - - - - - - 15, 16, 17, 18, 19 put in closed position G11.11.21
14. Installation order with base set n 50141K Keep 500-600 601-1200 1201-1800 1801-2400 250-400 11 8, 11 8, 10, 11 8, 9, 10, 11 put in closed position G11.11.22
15. Sill transmission with cable n 50102-35-... G11.11 Vent width (Fb) = 500-3600 mm Vent height (Fh) = 350-2400 mm Max. vent weight = 60 kg or or Available in 4 types. or Order code Cable length 50102-35-400 400 mm 50102-35-700 700 mm 50102-35-1000 1000 mm 50102-35-1250 1250 mm 50102-35-400 or -700 or -1000 or -1250 1 7821-1.2 coupling piece 2 7821-1.3 clip 2 7821-1.4 clip 1 7821-1.6 fixing plate 1 7821-400.1 cable or 7821-700.1 or 7821-1000.1 or 7821-1250.1 1 50102-35-1 track 1 50102-35-2 drive piece 1 50102-35-3 cover profile 1 50102-35-4 clip support 4 50102-35-5 fixing plate 5 M5x16 DIN 7500M screw 4 M5x8 DIN 965 screw 7 M4x6 DIN 965 screw 2 M6x6 DIN 916 screw Sill transmission with cable, used in combination with the handle or with the vertical winding gear. Cable in white (W), bronze (B) or grey (G). Order example: 50102-35-700-W. G11.11.23
15.1. Application possibilities 15.2. Vent weight The table below shows the maximum vent weight depending on the vent height and the profile depth. Vent height With sill transmission Glass position (X-value) > 1000 mm 60 kg 10-60 mm 800-1000 mm 60 kg 20-45 mm 800-1000 mm 50 kg 10-60 mm 600-800 mm 50 kg 10-30 mm 600-800 mm 40 kg 10-50 mm 600-800 mm 30 kg 10-60 mm 400-600 mm 22 kg 10-60 mm 250-400 mm 15 kg 10-60 mm G11.11.24
15.3. Installation order G11.11 Application A, C, D: X=min 60 Application B: X=min 160 OR G11.11.25
Option: X>160 mm Application C and D G11.11.26
16. Order tables Notes: Cover section n L7700-110: available in lengths of 3 m and 6 m. Rods n 7800-100-. (or 101, 102): available in lengths of 1 m, 2 m and 3 m. 16.1. Standard windows 500-650 651-1200 1201-1800 1801-2400 2401-3000 3001-3600 Fh = 400-1200 Fh = 1201-1800 Fh = 1801-2400 50141R or L + 2x 26140-750 50141R or L + 2x 26140-750 50141R or L + 30140-800 + 3x 26140-750 - 50141R or L + 50100-500 50141R or L + 50100-500 + 2x 30140-800 + 3x 30140-800 + 2x 26140-750 + 3x 26140-750 - 50141R or L + 50100-500 + 4x 30140-800 + 2x 26140-750 +35000-... rods in synthetic material +7800-100 (1,2) rods +L7700-110 +7800-150 clip cover section 50141R or L + 2x 30140-800 + 4x 26140-750 50141R or L + 50140-550R or L + 35000-165 + 2x 30140-800 + 5x 26140-750 - - - - - - - 50141R or L + 50140-550R or L + 35000-165 + 3x 30140-800 + 6x 26140-750 16.2. Small windows 500-1200 1201-1800 1801-2400 Fh = 250-400 50141KR or KL + 2x 26140-750 +35000-... rods in synthetic material +7800-100 (1,2) rods +L7700-110 +7800-150 clip cover section 50141KR or KL + 30140-800 + 3x 26140-750 50141KR or KL + 2x 30140-800 + 4x 26140-750 G11.11.27
17. General information The remote control system Invisitop can be used within the Fh/Fb sizes and weight limitations indicated on the chart below. Technical advise should be sought when the sizes of your window are not shown in the chart. The system is made of non-corroding materials. The set should not be installed in corrosive atmospheres. Sobinco can not be held responsible for the malfunctioning of the Invisitop system if any non-sobinco parts are used. All parts must be assembled according to the instructions as described in previous pages. The surface treatment of vent and frame must take place before assembly of the set, as this will affect the working of the gear. The glass must be glazed in accordance with national standards. The window and gear should be kept clean. Maximum vent weight depending on the vent height and the profile depth: Vent height Maximum vent weight With sill transmission Glass position (X-value) > 1000 mm 80 kg 60 kg 10-60 mm 800-1000 mm 80 kg 60 kg 20-45 mm 800-1000 mm 60 kg 50 kg 10-60 mm 600-800 mm 60 kg 50 kg 10-30 mm 600-800 mm 50 kg 40 kg 10-50 mm 600-800 mm 40 kg 30 kg 10-60 mm 400-600 mm 30 kg 22 kg 10-60 mm 250-400 mm 20 kg 15 kg 10-60 mm G11.11.28