SAFETY HOIST RINGS SHM - SHMR

SAFETY HOIST RINGS SHM - SHMR Hoist rings - CE REF G A B D E F H K TL (Kgm) P (Kg) W (Kg) SHM 0001 M8x1,25 10,9 32,0 9,7 12,5 67,8 46,7 19,0 1,0 400 0,17 SHM 0002 M10x1,50 10,9 30,0 9,7 17,5 67,8 46,7 19,0 1,7 450 0,17 SHM 0003 M12x1,75 22,4 60,5 19,0 19,0 121,4 89,4 38,1 3,8 1050 1,08 SHM 0004 M16x2,00 22,4 56,5 29,0 29,0 121,4 89,4 38,1 8,2 1900 1,12 SHM 0005 M20x2,50 22,4 52,5 34,0 34,0 121,4 89,4 38,1 13,6 2150 1,19 SHM 0006 M24x3,00 35,6 69,0 37,0 37,0 165,6 130,6 58,7 31,0 4200 3,10 SHM 0007 M30x3,50 44,5 107,4 41,9 41,9 221,7 165,1 81,0 60,0 7000 6,30 SHM 0009 M36x4,00 57,2 166,5 63,5 63,5 316,7 217,2 106,4 100,0 11000 15,50 SHM 0010 M42x4,50 57,2 160,5 68,0 68,0 316,7 217,2 106,4 100,0 12500 16,00 SHM 0011 M48x5,00 57,2 154,5 82,4 82,4 316,7 217,2 106,4 100,0 13500 16,80 SHM 0012 M64x6,00 76,2 210,0 101,6 101,6 419,1 297,6 146,0 290,0 22500 40,00 Spare parts REF G SHMR 0001 M8x1,25 SHMR 0002 M10x1,50 SHMR 0003 M12x1,75 SHMR 0004 M16x2,00 SHMR 0005 M20x2,50 SHMR 0006 M24x3,00 SHMR 0007 M30x3,50 SHMR 0009 M36x4,00 SHMR 0010 M42x4,50 SHMR 0011 M48x5,00 SHMR 0012 M64x6,00 Features Pivots and swivels to compensate for pitch, roll and sway when lifting heavy or unbalanced loads. High strength alloy steel with minimum tensile strenght of 1,250 MPa (125 kg/mm²) Certified heat treatment with 100% Magnaflux inspection. Corrosion resistant plating. Maximum operating temperature 200 C Safety factor is 5 times the rated load in any direction. Note standard tolerance: ±0,8 mm E=the use of spacers between bushing flange and mounting surface is not recommended as this will reduce the safety load rating. TL=recommended torque load +25% - 0. P=rated W=weight

SHSP Side pull hoist rings - CE for M8 + M10 for M12 - M48 REF P (Kg) A B C D E F G H I J K L M N O TL SHSP-0001 325 M8x1,25 33 16 21 3 14 8 25 25 25 44 76 19 13 13 5 SHSP-0002 500 M10x1,5 33 20 21 3 14 8 25 25 25 44 76 19 13 13 10 SHSP-0003 725 M12x1,75 48 24 35 4 21 13 44 38 86 51 120 32 19 22 20 SHSP-0004 1400 M16x2 48 32 48 4 21 13 44 38 86 51 120 32 19 22 40 SHSP-0005 2290 M20x2,5 59 40 48 6 26 16 57 51 102 67 145 44 25 29 70 SHSP-0006 3050 M24x3 59 48 83 6 26 16 57 51 102 67 145 44 25 29 140 SHSP-0007 4850 M30x3,5 90 60 83 9 42 27 95 76 196 111 265 76 49 48 350 SHSP-0009 7500 M36x4 90 72 83 9 42 27 95 76 196 111 265 76 49 48 550 SHSP-0010 8700 M42x4,5 90 84 83 9 42 27 95 76 196 111 265 76 49 48 800 SHSP-0011 10000 M48x5 90 96 83 9 42 27 95 76 196 111 265 76 49 48 1200 Features For lifting molds, tools and dies. Full swivel and pivot action flip and turn parts without unhooking. 200% proof tested. Safety factor is 5 times the rated load capacity. High quality alloy steel, finish black oxide. TL=recommended torque load +25% - 0. DSR - SS DSR Double swivel ring DSR: SS DSR: Class > 6 CE Very low overhang for improved safety Automatic realignment of the ring when in traction 90 Large support surface for a very high Resistance Two ways of tightening: either by open-ended spanner, or by allen key Improved stability with DSR C through centering section REF P SF KT M TL L1 S1 S2 A B C D E F G DSR M 8 3000 5 4 M 8 (x1,25) 6 14 8 16 33 30 30 38 27 14 53 DSR M 10 6000 5 5 M 10 (x1,50) 10 17 8 16 33 30 30 38 27 14 53 DSR M 12 10000 5 6 M 12 (x1,75) 15 21 8 16 33 30 30 38 27 14 53 DSR M 14* 13000 5 6 M 14 (x2) 30 23 8 20 45 42 45 54 38 17 76 DSR M 16 16000 5 7 M 16 (x2) 50 27 8 20 45 42 45 54 38 17 76 DSR M 18* 20000 5 7 M 18 (x2,5) 70 27 8 20 45 42 45 54 38 17 76 DSR M 20 25000 5 9 M 20 (x2,5) 100 30 8 20 45 42 45 54 38 17 76 DSR M 22* 30000 5 9 M 22 (x2,5) 120 33 14 24 62 55 60 83 55 25 107 DSR M 24 40000 5 11 M 24 (x3) 160 36 14 24 62 55 60 83 55 25 107 DSR M 27* 50000 5 13 M 27 (x3) 160 40 14 24 62 55 60 83 55 25 107 DSR M 30 63000 5 14 M 30 (x3,5) 250 45 14 24 62 55 60 83 55 25 107 REF P SF KT M TL L1 S1 S2 A B C D E F G SS DSR 6 M 8 3000 5 4 M 8 (x1,25) 6 16 6 32 30 30 39 28 13 53 SS DSR 13 M 8 3000 5 4 M 8 (x1,25) 6 16 13 30 30 30 39 28 13 53 SS DSR 8 M 10 5000 5 5 M 10 (x1,50) 10 16 8 34 30 30 39 28 13 53 SS DSR 17 M 10 5000 5 5 M 10 (x1,50) 10 16 17 31 30 30 39 28 13 53 SS DSR 10 M 12 8000 5 6 M 12 (x1,75) 15 19 10 33 30 30 39 28 13 53 SS DSR 19 M 12 8000 5 6 M 12 (x1,75) 15 19 19 30 30 30 39 28 13 53 SS DSR 24 M 16 15000 5 7 M 16 (x2) 50 26 24 44 40 42 54 38 17 77 SS DSR 30 M 20 16000 5 7 M 20 (x2,5) 100 30 30 43 40 42 54 38 17 77

DSRC Double swivel ring with centering Low overhang designed for total safety Improved stability with DSS C through centering section Perfectly symmetrical Screwing with allen key From M 33 to M 64 as standard; for loads 6.3 to 32.1 t REF P SF KT M/ø TL/Nm L1 S1 S2 A B C D E F G P DSRC M 8 3000 5 4 16 0/+0,25 6 14 8 16 33 30 30 38 27 14 53 3 +0,5/+1 DSRC M 10 6000 5 5 20 0/+0,25 10 17 8 16 33 30 30 38 27 14 53 3 +0,5/+1 DSRC M 12 10000 5 6 20 0/+0,25 15 21 8 16 33 30 30 38 27 14 53 3 +0,5/+1 DSRC M 14* 13000 5 6 20 0/+0,25 30 23 8 20 45 42 45 54 38 17 76 3 +0,5/+1 DSRC M 16 16000 5 7 20 0/+0,25 50 27 8 20 45 42 45 54 38 17 76 3 +0,5/+1 DSRC M 18* 20000 5 7 30 0/+0,30 70 27 8 20 45 42 45 54 38 17 76 3 +0,5/+1 DSRC M 20 25000 5 9 30 0/+0,30 100 30 8 20 45 42 45 54 38 17 76 3 +0,5/+1 DSRC M 22* 30000 5 9 30 0/+0,30 120 33 14 24 62 55 60 83 55 25 107 4 +0,5/+1 DSRC M 24 40000 5 11 30 0/+0,30 160 36 14 24 62 55 60 83 55 25 107 4 +0,5/+1 DSRC M 27* 50000 5 13 36 0/+0,30 160 40 14 24 62 55 60 83 55 25 107 4 +0,5/+1 DSRC M 30 63000 5 14 36 0/+0,30 250 45 14 24 62 55 60 83 55 25 107 4 +0,5/+1 DSS Double swivel shackle Low overhang designed for total safety Improved stability with DSS C through centering section Perfectly symmetrical Screwing with allen key From M 33 to M 64 as standard; for loads 6.3 to 32.1 t REF P S.F. KT M/ø TL/Nm L1 S A B C D E F G DSS M 33* 80000 5 14 M 33 (x3,5) 250 50 19 61 31 70 104 73 145 29 DSS M 36 100000 5 18 M 36 (x4) 320 54 19 61 31 70 104 73 145 29 DSS M 36x3* 100000 5 18 M 36 (x3) 320 54 19 61 31 70 104 73 145 29 DSS M 39* 100000 5 18 M 39 (x4) 320 54 19 61 31 70 104 73 145 29 DSS M 42 125000 5 20 M 42 (x4,5) 400 63 19 61 31 70 104 73 145 29 DSS M 42x3* 125000 5 20 M 42 (x3) 400 63 19 61 31 70 104 73 145 29 DSS M 45* 150000 4 22 M 45 (x4,5) 400 63 19 61 31 70 104 73 145 29 DSS M 48 200000 4 26 M 48 (x5) 600 68 19 79 38 90 125 91 184 33 DSS M 48x3* 200000 4 26 M 48 (x3) 600 68 19 79 38 90 125 91 184 33 DSS M 48x4* 200000 4 26 M 48 (x4) 600 68 19 79 38 90 125 91 184 33 DSS M 52* 200000 4 26 M 52 (x5) 600 68 19 79 38 90 125 91 184 33 DSS M 56 250000 4 28 M 56 (x5,5) 600 78 19 79 38 90 125 91 184 33 DSS M 56x4* 250000 4 28 M 56 (x4) 600 78 19 79 38 90 125 91 184 33 DSS M 64 321000 4 36 M 64 (x6) 600 90 19 79 38 95 125 91 184 33 DSS M 64x4* 321000 4 36 M 64 (x4) 600 90 19 79 38 95 125 91 184 33 DSS M 72* 321000 4 36 M 72 (x6) 600 90 19 79 38 95 125 91 184 33 DSS M 72x4* 321000 4 36 M 72 (x4) 600 90 19 79 38 95 125 91 184 33 DSS M 80* 321000 4 36 M 80 (x6) 600 90 19 79 38 95 125 91 184 33 DSS M 100* 321000 4 36 M 100 (x6) 600 90 19 79 38 95 125 91 184 33

DSSC Double swivel shackle with centering Improvement: The hook does not scrape the tool when in traction at 90 Three free articulations Very low overhang designed for total safety Perfectly symmetrical Two ways of tightening: either by open-ended spanner, or by allen key for total quality Improved stability with TSR C through centering section REF P S.F. KT M/ø TL/Nm L S A B C D E F G P DSSC M 33* 8000 5 14 48 +0,10/+0,30 250 50 19 61 31 70 104 73 145 29 6 +0,5/+1 DSSC M 36 10000 5 18 48 +0,10/+0,30 320 54 19 61 31 70 104 73 145 29 6 +0,5/+1 DSSC M 36x3* 10000 5 18 48 +0,10/+0,30 320 54 19 61 31 70 104 73 145 29 6 +0,5/+1 DSSC M 39* 10000 5 18 48 +0,10/+0,30 320 54 19 61 31 70 104 73 145 29 6 +0,5/+1 DSSC M 42 12500 5 20 48 +0,10/+0,30 400 63 19 61 31 70 104 73 145 29 6 +0,5/+1 DSSC M 42x3* 12500 5 20 48 +0,10/+0,30 400 63 19 61 31 70 104 73 145 29 6 +0,5/+1 DSSC M 45* 15000 4 22 48 +0,10/+0,30 400 63 19 61 31 70 104 73 145 29 8 +0,5/+1 DSSC M 48 20000 4 26 64 +0,60/+0,10 600 68 19 79 38 90 125 91 184 33 8 +0,5/+1 DSSC M 48x3* 20000 4 26 64 +0,60/+0,10 600 68 19 79 38 90 125 91 184 33 8 +0,5/+1 DSSC M 48x4* 20000 4 26 64 +0,60/+0,10 600 68 19 79 38 90 125 91 184 33 8 +0,5/+1 DSSC M 52* 20000 4 26 64 +0,60/+0,10 600 68 19 79 38 90 125 91 184 33 8 +0,5/+1 DSSC M 56 25000 4 28 64 +0,60/+0,10 600 78 19 79 38 90 125 91 184 33 8 +0,5/+1 DSS C M 56x4* 25000 4 28 64 +0,60/+0,10 600 78 19 79 38 90 125 91 184 33 8 +0,5/+1 DSS C M 64 32100 4 36 74 +0,60/0,10 600 90 19 79 38 95 125 91 184 33 10 +0,5/+1 DSS C M 64x4* 32100 4 36 74 +0,60/0,10 600 90 19 79 38 95 125 91 184 33 10 +0,5/+1 TSR Triple swivel shackle *Non-Standard Improvement: The hook does not scrape the tool when in traction at 90 Three free articulations Very low overhang designed for total safety Perfectly symmetrical Two ways of tightening: either by open-ended spanner, or by allen key for total quality Improved stability with TSR C through centering section REF P S.F. KT M/ø TL/Nm L1 X S1 S2 A B C D E F G TSR M 8 3000 5 4 M 8 (x1,25) 6 14 18 8 16 33 56 30 41 25 10 58 TSR M 10 6000 5 5 M 10 (x1,50) 10 17 18 8 16 33 56 30 41 25 10 58 TSR M 12 10000 5 6 M 12 (x1,75) 15 21 18 8 16 33 56 30 41 25 10 58 TSR M 14* 13000 5 6 M 14 (x2) 30 23 24 8 20 45 76 45 56 37 14 79 TSR M 16 16000 5 7 M 16 (x2) 50 27 24 8 20 45 76 45 56 37 14 79 TSR M 18* 20000 5 7 M 18 (x2,5) 70 27 28 8 20 45 76 45 56 37 14 79 TSR M 20 25000 5 9 M 20 (x2,5) 100 30 28 8 20 45 81 45 56 37 14 79 TSR M 22* 30000 5 9 M 22 (x2,5) 120 33 45 14 24 62 105 60 80 45 20 106 TSR M 24 40000 5 11 M 24 (x3) 160 36 45 14 24 62 105 60 80 45 20 106 TSR M 27* 50000 5 13 M 27 (x3) 160 36 45 14 24 62 105 60 80 45 20 106 TSR M 30 63000 5 14 M 30 (x3,5) 250 45 45 14 24 62 105 60 80 45 20 106 TSR M 36 100000 5 18 M 36 (x4) 320 54 54 19 30 81 140 80 111 71 30 148 TSR M 42 125000 5 20 M 42 (x4,5) 400 63 58 19 30 84 146 80 111 71 30 148 TSR M 48 200000 4 26 M 48 (x5) 600 68 69 19 30 100 178 110 135 90 42 180 TSR M 56 220000 4 36 M 56 (x5,5) 600 78 73 19 30 104 184 110 135 90 42 190

TSR C Triple swivel shackle with centering One free articulation Very low overhang for increased safety Automatic realignment of the ring when in traction in 90 Large support surface for a very high resistance Improved stability with SEB C through centering section REF P S.F. KT M/ø TL/Nm L1 X S1 S2 A B C D E F G P TSRC M 8 3000 5 4 16 0/+0,25 14 58 16 6 8 33 33 56 30 41 25 10 3 +0,5/+1 TSRC M 10 6000 5 5 20 0/+0,25 17 58 16 10 8 33 33 56 30 41 25 10 3 +0,5/+1 TSRC M 12 10000 5 6 20 0/+0,25 21 58 16 15 8 33 33 56 30 41 25 10 3 +0,5/+1 TSRC M 14 13000 5 6 20 0/+0,25 30 23 24 8 20 45 76 45 56 37 14 79 3 +0,5/+1 TSRC M 16 16000 5 7 20 0/+0,25 50 27 24 8 20 45 76 45 56 37 14 79 3 +0,5/+1 TSRC M 18 20000 5 7 30 0/+0,30 27 79 20 70 8 45 45 76 45 56 37 14 3 +0,5/+1 TSRC M 20 25000 5 9 30 0/+0,30 30 79 20 100 8 45 45 81 45 56 37 14 3 +0,5/+1 TSRC M 22 30000 5 9 30 0/+0,30 33 106 24 120 14 62 62 105 60 80 45 20 4 +0,5/+1 TSRC M 24 40000 5 11 30 0/+0,30 160 36 45 14 24 62 105 60 80 45 20 106 4 +0,5/+1 TSRC M 27 50000 5 13 36 0/+0,30 160 36 45 14 24 62 105 60 80 45 20 106 4 +0,5/+1 TSRC M 30 63000 5 14 36 0/+0,30 45 106 24 250 14 62 62 105 60 80 45 20 4 +0,5/+1 TSRC M 36 100000 5 18 48 +0,10/+0,50 320 54 54 19 30 81 140 80 111 71 30 148 6 +0,5/+1 TSRC M 42 125000 5 20 48 +0,10/+0,50 63 148 30 400 19 84 84 146 80 111 71 30 6 +0,5/+1 TSRC M 48 200000 4 26 64 +0,10/+0,60 600 68 69 19 30 100 178 110 135 90 42 180 8 +0,5/+1 TSRC M 56 220000 4 36 64 +0,10/+0,60 78 190 30 600 19 104 104 184 110 135 90 42 8 +0,5/+1 SEB Swivel eye bolt *Non-Standard One free articulation Very low overhang for increased safety Automatic realignment of the ring when in traction in 90 Large support surface for a very high resistance Improved stability with SEB C through centering section REF P S.F. KT M/ø TL/Nm L1 X S A B C D SEB M 16 16000 5 7 M 16 (x2) 50 27 35 8 38 45 90 78 SEB M 20 25000 5 9 M 20 (x2,5) 100 30 35 8 38 45 90 78 SEB M 24 40000 5 11 M 24 (x3) 160 36 50 14 58 70 134 115 SEB M 30 63000 5 14 M 30 (x3,5) 250 45 50 14 58 70 134 115 SEB M 36 100000 5 18 M 36 (x4) 320 54 70 14 88 94 190 166 SEB M 42 125000 5 20 M 42 (x4,5) 400 63 70 14 88 94 190 166

SEBC Swivel eye bolt with centering REF P S.F. KT M/ø TL/Nm L1 X S A B C D P SEBC M 16 16000 5 7 20 0/+0,25 50 27 35 8 38 45 90 78 3 +0,5/+1 SEBC M 20 25000 5 9 30 0/+0,25 100 30 35 8 38 45 90 78 3 +0,5/+1 SEBC M 24 40000 5 11 30 0/+0,30 160 36 50 14 58 70 134 115 4 +0,5/+1 SEBC M 30 63000 5 14 36 0/+0,30 250 45 50 14 58 70 134 115 4 +0,5/+1 SEBC M 36 100000 5 18 48 +0,50/+0,10 320 54 70 14 88 94 190 166 6 +0,5/+1 SEBC M 42 125000 5 20 48 +0,50/+0,10 400 63 70 14 88 94 190 166 6 +0,5/+1 One free articulation Very low overhang for increased safety Automatic realignment of the ring when in traction in 90 Large support surface for a very high resistance Improved stability with SEB C through centering section DSP Double swivel lifting bolt Very low overhang for improved safety Automatic realignment of the ring when in traction 90 Large support surface for a very high Resistance Two ways of tightening: either by open-ended spanner, or by allen key Improved stability with DSR C through centering section REF P S.F. KT M/ø TL/Nm L1 S1 S2 A B C E F G DSP M 8 3000 5 4 M 8 (x1,25) 6 14 8 16 33 56 30 19 19 58 DSP M 10 6000 5 5 M 10 (x1,50) 10 17 8 16 33 56 30 19 19 58 DSP M 12 10000 5 6 M 12 (x1,75) 15 21 8 16 33 56 30 19 19 58 DSP M 14* 13000 5 6 M 14 (x2) 30 23 8 20 45 76 45 25 27 79 DSP M 16 16000 5 7 M 16 (x2) 50 27 8 20 45 76 45 25 27 79 DSP M 18* 20000 5 7 M 18 (x2,5) 70 27 8 20 45 76 45 25 27 79 DSP M 20 25000 5 7 M 20 (x2,5) 100 30 8 20 45 81 45 25 27 79

DSPC Double swivel lifting bolt with centering REF P S.F. KT M/ø TL/Nm L1 S1 S2 A B C E F G P DSPC M 8 3000 5 4 16 0/+0,25 6 14 8 16 33 56 30 19 19 58 3 +0,5/1 DSPC M 10 6000 5 5 20 0/+0,25 10 17 8 16 33 56 30 19 19 58 3 +0,5/1 DSPC M 12 10000 5 6 20 0/+0,25 15 21 8 16 33 56 30 19 19 58 3 +0,5/1 DSPC M 14 13000 5 6 20 0/+0,25 30 23 8 20 45 76 45 25 27 79 3 +0,5/1 DSPC M 16 16000 5 7 20 0/+0,25 50 27 8 20 45 76 45 25 27 79 3 +0,5/1 DSPC M 18 20000 5 7 30 0/+0,30 70 27 8 20 45 76 45 25 27 79 3 +0,5/1 DSPC M 20 25000 5 7 30 0/+0,30 100 30 8 20 45 81 45 25 27 79 3 +0,5/1 Very low overhang for improved safety Automatic realignment of the ring when in traction 90 Large support surface for a very high Resistance Two ways of tightening: either by open-ended spanner, or by allen key Improved stability with DSR C through centering section CSS Central safety shackle for dispose on press Indicative table for fastening with socket head screws DIN 912-12.9 Head Ø Height * WLL Max. N.m. mm mm mm mm dan M 36 54 36 54 9600 600 M 30 45 30 45 6600 420 M 24 36 24 36 4100 200 M 20 30 20 30 2800 150 * Minimum effective thread length REF X A B C D E F G H I J K Kg CSS 40 (mini) 80 330 50 62 90 88 98 132 38 76 41 17 A compact, lightweight solution for removing the mold from the press

DSH Double swivel hook REF A B C D E F G L1 M/ø TL/Nm Kg S1 S2 P S.F. DSH M8 33 56 30 44 32 23 58 14 M8 (x1,25) 6 0,8 8 16 0,3 5 DSH M10 33 56 30 44 32 23 58 17 M10 (x1,50) 10 0,8 8 16 0,6 5 DSH M12 33 56 30 44 32 23 58 21 M12 (x1,75) 15 0,8 8 16 1,0 5 DSH M14* 45 76 45 58 29 29 79 23 M14 (x2) 30 1,9 8 20 1,3 5 DSH M16 45 76 45 58 29 29 79 27 M16 (x2) 50 2,0 8 20 1,6 5 DSH M18* 45 76 45 58 29 29 79 27 M18 (x2,5) 70 2,0 8 20 2,0 5 DSH M20 45 81 45 58 29 29 79 30 M20 (x2,5) 100 2,0 8 20 2,5 5 P= max load in TO RM Eyebolts 1.7131 60 HRC REF A D1 D2 L H (N) K M RM 8 20 20 36 13,0 36 1400 8 M8 x 1,25 RM 10 25 25 45 17,0 45 2300 10 M10 x 1,50 RM 12 30 30 54 20,5 53 3400 12 M12 x 1,75 RM 14 35 35 63 27,0 62 4900 14 M14 x 2,00 RM 16 35 35 63 27,0 62 7000 14 M16 x 2,00 RM 18 40 40 72 30,0 71 9000 16 M18 x 2,50 REF A D1 D2 L H (N) K M RM 20 40 40 72 30,0 71 12000 16 M20 x 2,50 RM 22 45 45 92 34,0 90 15000 18 M22 x 2,50 RM 24 50 50 90 36,0 90 18000 20 M24 x 3,00 RM 27 50 50 90 36,0 90 18000 20 M27 x 3,00 RM 30 65 60 108 45,0 109 36000 24 M30 x 3,50 RM 36 75 70 126 54,0 128 51000 28 M36 x 4,00 AT P: 0800 301 060 F: 0800 401 020 dme_oesterreich@milacron.com BE P: +32 (0) 15 28 87 30 F: +32 (0) 15 40 51 17 dme_benelux@milacron.com CH P: +41 0848 567 364 F: +41 0848 567 365 dme_schweiz@milacron.com CZ P: 800 142 451 +420 572 151 754 F: 800 142 450 +420 571 611 996 dme_cz@milacron.com DE P: 0800 664 82 50 +49 (0) 2351 437 0 F: 0800 664 82 51 +49 (0) 2351 437 220 dme_normalien@milacron.com ES P: 900 900 342 F: 900 900 343 dme_iberia@milacron.com FR P: +33 1 49 93 92 23 F: +33 1 49 93 92 22 dme_france@milacron.com HU P: 0680 205 00 +32 15 28 87 30 F: +32 15 40 51 17 dme_hungary@milacron.com IT P: 800 089 734 F: 800 089 735 dme_italy@milacron.com NL P: +31 (0) 20 654 5571 F: +31 (0) 20 654 5572 dme_benelux@milacron.com PL P: +800 331 1312 +32 15 21 50 92 F: +800 331 1313 +32 15 40 51 92 dme_polska@milacron.com PT P: 800 207 900 F: 800 207 901 dme_iberia@milacron.com SK P: 0800 142 451 +420 572 151 754 F: 0800 142 450 +420 571 611 996 dme_cz@milacron.com UK P: +44 2071 3300 37 F: +44 2071 3300 36 dme_uk@milacron.com Other Countries P: +32 15 28 87 30 F: +32 15 40 51 17 dme_export@milacron.com