Drive module RE 51145/06.12 Replaces: 05.12 1/16 Type UPE 5 Component series 1X Maximum operating pressure 250 bar Drive power 2.2 to 4.0 kw H7328 Table of contents Contents Page Features, applications 1 Function, section, symbols 2 Ordering code, standard types 3 Mounting IH15B control module 4 Technical data, hydraulic 5 Selection table for pump and electric motor 5, 6 Electric motor: 7 Technical data Electromagnetic compatibility of devices (EMVG) Terminal assignment Unit dimensions 8, 9 Filling and sampling volume, installation information 10 Sound pressure level 11, 12 Oil-air cooler 12, 13 Water cooler 13 Options Level switch 13 Temperature switch 14 Oil tray 14 Commissioning information 15 Features 100 % duty cycle Compact design Low-noise High cooling power Broad field of application Large number of variants Different mounting possibilities Complete hydraulic control possible (in this connection see data sheet 51156) Ready for connection Applications Machine tools Lifting platforms Conveyors Test stands Winding machines Information on available spare parts: www.boschrexroth.com/spc
2/16 Bosch Rexroth AG Hydraulics UPE 5 RE 51145/06.12 Function, section, symbols 7 8 4 1 9 max 5 min Air flow 2 6 3 10 Due to its concept, the drive module type UPE 5 has a very compact design. The pump (2) is driven by means of the electric motor (1). Electric motor and pump are connected without coupling. The pump shaft is plugged into the hollow drilled shaft end of the electric motor. That keeps the pumpmotor group very short. The pump (2) sucks in the hydraulic fluid from the tank (4) through the suction hose (3) and delivers it to the hydraulic control. The hydraulic fluid flowing back from the control can be led through the oil-air cooler (5) via the ports K1 and K2. Afterwards, the cooled hydraulic fluid is led back into the tank. By means of the axial fan wheel (6) mounted at the electric motor, cold fresh air is sucked in by the oil-air cooler (5). This cools the hydraulic fluid and the electric motor. The tank (4) can be filled through the filling plug (7). The oil level can be monitored by means of the oil level display (8). The tank is closed by a tank cover (9). To it, the pump/motor group (1; 2) and the terminal box (10) are attached. The drive module is delivered ready for connection. Optionally, the drive module can also be equipped with an electric monitoring of the oil level, the oil temperature and a complete hydraulic control (see 51156) e.g. filter, accumulator and valves. Upon request, oil-water cooling, oil tray according to the Water Resources Act (WHG), double pump as well as an additional tank are also possible. Attention! The drive module may heat up during operation Risk of injury! Symbol for control pump (A10VSO, V7) Symbol for fixed displacement pump (GF2, AZ) T2 T1 K2 T3 T4 T5 M K1 P S T L K1 = G1/2 K2 = G1/2 T1 = G1 T2 = G1/2 T3 = G1 T4 = G1/2 T5 = G1 T = G1/2 T2 T1 K2 T3 T4 T5 M K1 S T P K1 = G1/2 K2 = G1/2 T1 = G1 T2 = G1/2 T3 = G1 T4 = G1/2 T5 = G1 T = G1/2
RE 51145/06.12 UPE 5 Hydraulics Bosch Rexroth AG 3/16 Ordering code UPE 5 1X * Component series 10 to 19 = 1X (10 to 19: unchanged installation and connection dimensions) Drive power kw = 2,2 3.00 kw = 3,0 4.00 kw = 4,0 Pumps Axial piston variable displacement pumps A10VSO10DFR1/52R-PPA14N00 (data sheet 92073) = A10VSO10 A10VSO18DFR1/31R-PPA12N00 (data sheet 92712) = A10VSO18 Internal gear pumps (data sheet 10213) PGF2-2X/006RE01VE4 = GF2/006 PGF2-2X/008RE01VE4 = GF2/008 PGF2-2X/011RE01VE4 = GF2/011 PGF2-2X/013RE01VE4 = GF2/013 PGF2-2X/016RE01VE4 = GF2/016 External gear pumps (data sheet 10089) AZPF-1X-004RAB01MB = AZ/004 AZPF-1X-005RAB01MB = AZ/005 AZPF-1X-008RAB01MB = AZ/008 AZPF-1X-011RAB01MB = AZ/011 AZPF-1X-016RAB01MB = AZ/016 AZPF-1X-022RAB01MB = AZ/022 Vane pumps PV7-1X/10-14RE01MC0-16 = V7/10-14 PV7-1X/10-20RE01MC0-10 Data sheet 10515 = V7/10-20 PV7-1X/16-20RE01MC0-16 = V7/16-20 PV7-1X/06-10RA01MA0-10 = V7/06-10 PV7-1X/06-14RA01MA0-07 Data sheet 10522 = V7/06-14 PV7-2X/20-20RA01MA0-10 = V7/20-20 PV7-2X/20-25RA01MA0-10 = V7/20-25 Further details in the plain text 1) Set-up hydraulic control (in this connection see data sheet 51156) 0 = without set-up 1 = with set-up Installation variants H = Horizontal mounting S = Vertical mounting W = Wall mounting Oil monitoring A = Oil level display AN = Oil level display with level switch AT = Oil level display and temperature switch ANT = Oil level display with level and temperature switch 1) e.g. Material no. of the attached control Special version Standard types: Drive module Type A10VSO UPE5-1X/4,00A10VSO10A-H-0 UPE5-1X/4,00A10VSO18A-H-0 Type PGF2 UPE5-1X/4,00GF2/006A-H-0 UPE5-1X/4,00GF2/008A-H-0 UPE5-1X/4,00GF2/011A-H-0 UPE5-1X/4,00GF2/013A-H-0 UPE5-1X/4,00GF2/016A-H-0 Type AZPF UPE5-1X/4,00AZ/004A-H-0 UPE5-1X/4,00AZ/005A-H-0 UPE5-1X/4,00AZ/008A-H-0 UPE5-1X/4,00AZ/011A-H-0 UPE5-1X/4,00AZ/016A-H-0 UPE5-1X/4,00AZ/022A-H-0 Material no. R904100332 R901328541 R901077149 R901328588 R901328587 R901328586 R901328585 R901328589 R901328583 R901071582 R901328582 R901328581 R901073015 Type PV7 UPE5-1X/4,00V7/06-14A-H-0 UPE5-1X/4,00V7/10-14A-H-0 UPE5-1X/4,00V7/10-20A-H-0 UPE5-1X/4,00V7/16-20A-H-0 Material no. R900987596 R900987572 R901328957 R901328956
4/16 Bosch Rexroth AG Hydraulics UPE 5 RE 51145/06.12 Mounting IH15B control module The control modules for the UPE5 drive module serves the realization of complete hydraulic controls. They can be fitted and mounted individually. The filter or accumulator safety module establishes the connection of the hydraulic control to port K2 of the drive module. The IH15B control modules (in this connection see data sheet 51156) with the connection modules can be attached to the filter or accumulator safety module. Direction C F A B E D Project planning information The entire length of the IH15B control should not exceed the length of the UPE5 drive module. Maximum recommended total length I = 500 mm. Please consult us if the entire length of the necessary control is longer.
RE 51145/06.12 UPE 5 Hydraulics Bosch Rexroth AG 5/16 Technical Data (For applications outside these parameters, please consult us!) general Weight (without hydraulic fluid and pump 1) ) kg 75 Direction of rotation hydraulic Clockwise Hydraulic fluid Mineral oil HLP according to DIN 51524 part 2 Please observe our regulations according to data sheet 07075! Hydraulic fluid temperature range C 10 to +70 (admissible viscosity range of the pump and the valves must be observed!) Viscosity range mm 2 /s See viscosity range of the pump and the valves Max. admissible degree of contamination of the hydraulic fluid Cleanliness class according to ISO 4406 (c) Class 20/18/15 2) 1) For the pump weights see data sheets 10089, 10213, 10515, 10522, 92712 and 92713. 2) The cleanliness classes specified for the components must be adhered to in hydraulic systems. Effective filtration prevents faults and at the same time increases the service life of the components. For selecting the filters, see data sheet 51156. Selection table for pump and electric motor with n = 1450 min 1 Axial piston variable displacement pump 3) A10VSO10DFR1/52R- PPA14N00 = 220 bar A10VSO18DFR1/31R- PPA12N00 = 250 bar Internal gear pump q Vmax l/min PGF2-2X/006RE01VE4 9.4 PGF2-2X/008RE01VE4 11.9 PGF2-2X/011RE01VE4 16.0 PGF2-2X/013RE01VE4 19.3 PGF2-2X/016RE01VE4 23.2 bar P kw 70 15.0 95 3.00 125 4.00 4.0 5.5 220 3.00 7.5 4.00 40 27.0 50 3.00 70 4.00 4.0 5.5 250 3.00 7.5 4.00 q Vmax P l/min bar kw 110 150 3.00 200 4.00 90 120 3.00 160 4.00 65 90 3.00 120 4.00 55 75 3.00 100 4.00 45 60 3.00 80 4.00 External gear pump q Vmax l/min AZPF-1X-004RAB20MB 5.8 AZPF-1X-005RAB20MB 7.9 AZPF-1X-008RAB01MB 11.8 AZPF-1X-011RAB01MB 16.0 AZPF-1X-016RAB01MB 23.2 AZPF-1X-022RAB01MB 31.9 bar P kw 180 245 3.00 250 4.00 130 180 3.00 250 4.00 90 120 3.00 200 4.00 65 90 3.00 140 4.00 45 60 3.00 100 4.00 40 55 3.00 75 4.00 3) The axial piston variable displacement pumps can - within their maximum values (e.g. A10VSO10DFR1/52R-PPA14N00, = 250 bar, q Vmax = 15 l/min) - be operated with all values (e.g. A10VSO10DFR1/52R-PPA14N00, = 180 bar, q Vmax = 8 l/min and P Motor = 3.0 kw) if the admissible power of the electric motor is not exceeded.
6/16 Bosch Rexroth AG Hydraulics UPE 5 RE 51145/06.12 Selection table for pump and electric motor with n = 1450 min 1 Vane pump 1) PV7-1X/10-14RE01MC0-16 = 160 bar PV7-1X/10-20RE01MC0-10 = 100 bar PV7-1X/16-20RE01MC0-16 = 160 bar PV7-1X/06-10RA01MA0-10 = 100 bar PV7-1X/06-14RA01MA0-07 = 70 bar q Vmax l/min bar P kw 50 21.0 65 3.00 90 4.00 6.5 9.0 160 3.00 12.0 4.00 35 29.0 50 3.00 65 4.00 10.5 14.5 100 3.00 19.0 4.00 35 29.0 50 3.00 65 4.00 6.5 9.0 160 3.00 12.0 4.00 70 14.5 100 3.00 100 4.00 10.5 14.5 100 3.00 14.5 4.00 50 20.0 70 3.00 70 4.00 15.0 20.0 70 3.00 20.0 4.00 Vane pump 1) PV7-2X/20-20RA01MA0-10 = 100 bar PV7-2X/20-25RA01MA0-10 = 100 bar q Vmax l/min bar P kw 35 29 50 3.00 65 4.00 10.5 14.5 100 3.00 19.0 4.00 30 36 40 3.00 55 4.00 10.5 14.5 100 3.00 19.0 4.00 1) The vane pumps can - within their maximum values (e.g. PV7-1X/10-14RE01MC0-16, = 160 bar, q Vmax = 21 l/min) - be operated with all values (e.g. PV7-1X/10-14RE01MC0-16, = 80 bar, q V = 13 l/min and P Motor = 2.2 kw) if the admissible power of the electric motor is not exceeded.
RE 51145/06.12 UPE 5 Hydraulics Bosch Rexroth AG 7/16 Electric motor The electric motor is designed for the mode of operation according to VDE 0530 part 1 (EN 60034) for continuous operation S1 within the rated power range. The electric motor complies with insulation class F and protection class IP 55. The electric motor is to be connected so that it rotates in clockwise direction (clockwise direction of rotation). It can be used at power mains with the frequency 50 Hz or 60 Hz without modification. Technical Data (For applications outside these parameters, please consult us!) Voltage (other voltage values on request) U V 400 / 690 ±6 % /Y Frequency f Hz 50 / 60 Mode of operation S1 continuous operation Insulation class F (winding) Protection class according to VDE 0530 / EN 60034 IP 55 Number of poles 4 Power kw Frequency 50 Hz Speed min 1 Power factor cos ϕ Rated current with 400 Volt 2.2 1440 0,77 5.2 A 3.0 1415 0.76 7.0 A 4.0 1390 0.73 9.8 A Power kw Frequency 60 Hz Speed min 1 Power factor cos ϕ Rated current with 400 Volt 2.2 1710 0.84 4.8 A 3.0 1700 0.83 6.4 A 4.0 1680 0.77 9.3A Electromagnetic compatibility of devices (EMVG) According to the "Act on the electromagnetic compatibility of devices" ( 2, subsection 4) and the directive 89/336 EEC, the drive module is no device that is ready for operation. In order to avoid electromagnetic interferences that might occur, an interference suppression element e.g. type 23 050, 3 x 400 VAC, 50-60 Hz by the company Murr-Elektronik (D-71570 Oppenweiler) is recommended. Terminal assignment Terminal assignment in the terminal box at the drive module Factory-side: Customer-side: triangle U = 400 V W2 U2 V2 U1 V1 W1 W2 U2 V2 PE L1 L2 L3 Customer-side: Y star U = 690 V W2 U2 V2 U1 V1 W1 U1 V1 W1 PE L1 L2 L3
500 8/16 Bosch Rexroth AG Hydraulics UPE 5 RE 51145/06.12 Unit dimensions: (dimensions in mm) Installation variant: Horizontal mounting T3 T4 T5 max min C 485 B 26 40 55 376 500 4 x Ø11 L1 35 T1 315 350 375 T2 A K2 Additional tank (option) A B C Filling volume 5 liters 600 105 122 Filling volume 10 liters 600 205 122 Installation variant: Vertical mounting K2 max L2 min T5 T4 T3 L3 35 315 4x Ø11 350 375 Dimensions L1, L2 and L3 see page 9 355 435 445
RE 51145/06.12 UPE 5 Hydraulics Bosch Rexroth AG 9/16 Unit dimensions (dimensions in mm) Installation variant: Wall mounting 500 55 40 376 26 4x Ø11 L1 X K2 440 425 390 T3 T4 T5 View X T1 410 435 T2 Pump type Nominal dimension L1 L2 L3 Axial piston variable displacement pump A10VSO10DFR1/52R-PPA14N00 164 725 755 A10VSO18DFR1/31R-PPA12N00 195 705 735 Internal gear pump PGF2-2X/006RE01VE4 114 630 660 PGF2-2X/008RE01VE4 117.5 705 735 PGF2-2X/011RE01VE4 123 705 735 PGF2-2X/013RE01VE4 128 705 735 PGF2-2X/016RE01VE4 133 705 735 External gear pump AZPF-1X-004RAB20MB 85 630 660 AZPF-1X-005RAB20MB 86 630 660 AZPF-1X-008RAB01MB 90 630 660 AZPF-1X-011RAB01MB 95 630 660 AZPF-1X-016RAB01MB 103 630 660 AZPF-1X-022RAB01MB 115 630 660 Vane pump PV7-1X/10-14RE01MC0-16 149 705 735 PV7-1X/10-20RE01MC0-10 149 705 735 PV7-1X/16-20RE01MC0-16 165 725 755 PV7-1X/06-10RA01MA0-10 101 630 660 PV7-1X/06-14RA01MA0-07 101 630 660 PV7-2X/20-20RA01MA0-10 135 705 735 PV7-2X/20-25RA01MA0-10 135 705 735
10/16 Bosch Rexroth AG Hydraulics UPE 5 RE 51145/06.12 Filling and sampling volume (in liters) max min max min Installation variant: Horizontal mounting and wall mounting Installation variant: Vertical mounting Installation variant: Horizontal mounting and wall mounting Installation variant: Vertical mounting Filling volume 23 26 Sampling volume 4.5 3.5 Sampling volume Switching point level switch 3.5 2.0 Installation information (in mm) > 200 max > 100 min Necessary minimum distance to the wall for perfect cooling.
RE 51145/06.12 UPE 5 Hydraulics Bosch Rexroth AG 11/16 Sound pressure level (measured with n = 1450 min 1, ν = 41 mm 2 /s and ϑ = 50 C) Sound pressure level for axial piston variable displacement pump A10VSO (in this connection see data sheet 92712, 92713) Sound pressure level in db(a) 72 70 68 66 64 62 60 58 56 Sound pressure level for internal gear pump PGF2-2X (in this connection see data sheet 10213) 72 70 PGF2-2X/006RE01VE4 68 PGF2-2X/008RE01VE4 66 PGF2-2X/011RE01VE4 64 PGF2-2X/013RE01VE4 62 PGF2-2X/016RE01VE4 Sound pressure level in db(a) 60 74 72 70 68 66 64 Sound pressure level for vane pump PV7-1X (in this connection see data sheet 10515) 72 70 68 66 64 62 60 58 56 20 40 60 80 100 120 140 160 180 200 Operating pressure in bar Sound pressure level for external gear pump AZPF-1X/ (in this connection see data sheet 10089) Sound pressure level in db(a) Sound pressure level in db(a) A10VSO10DFR1/52R-PPA14N00 A10VSO18DFR1/31R-PPA12N00 20 40 60 80 100 120 140 160 180 200 220 240 250 Operating pressure in bar 20 40 60 80 100 120 140 160 180 200 220 240 260 Operating pressure in bar 20 30 40 50 60 70 80 90 100 110 120 140 160 Operating pressure in bar AZPF-1X-004RAB20MB AZPF-1X-005RAB20MB AZPF-1X-008RAB01MB AZPF-1X-011RAB01MB AZPF-1X-016RAB01MB AZPF-1X-022RAB01MB PV7-1X/10-14RE01MC0-16 PV7-1X/10-20RE01MC0-10 PV7-1X/16-20RE01MC0-16
12/16 Bosch Rexroth AG Hydraulics UPE 5 RE 51145/06.12 Sound pressure level (measured with n = 1450 min 1, ν = 41 mm 2 /s and ϑ = 50 C) Sound pressure level for vane pump PV7-1X (in this connection see data sheet 10522) 72 PV7-1X/06-10RA01MA0-10 70 68 66 PV7-1X/06-14RA01MA0-07 64 62 60 58 56 20 30 40 50 60 70 80 90 100 Operating pressure in bar Sound pressure level in db(a) Sound pressure level for vane pump PV7-2X (in this connection see data sheet 10522) Sound pressure level in db(a) 72 70 68 PV7-2X/20-20RA01MA0-10 66 64 62 60 PV7-2X/20-25RA01MA0-10 58 56 20 40 60 80 100 Operating pressure in bar Oil-air cooler 1) By means of the oil-air cooler, high power density (ratio between drive power and tank size) of the UPE 5 drive module is achieved. In this way, the drive module with the oil-air cooler can be used in continuous operation. The maximum operating pressure of the oil-air cooler is = 10 bar. Cooling power with t = 40 C in kw 4,0 3,5 3,0 2,5 2,0 1,5 1,0 0,5 Specific cooling power in kw/k 0,1000 0,0875 0,0750 0,0625 0,0500 0,0375 0,0250 0,0125 Cooling power 0,0 0,0000 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Flow in l/min 1) On request, oil-water coolers are also possible!
RE 51145/06.12 UPE 5 Hydraulics Bosch Rexroth AG 13/16 p - q v characteristic curve (measured with ν = 41 mm 2 /s and ϑ = 50 C) Pressure differential in bar 2,0 1,5 1,0 0,5 0 5 10 15 20 25 30 35 40 Flow in l/min Water cooler (optional) Water cooler on request Level switch (option) Function The level switch provides for electric monitoring of the hydraulic fluid filling level. If the minimum oil level is reached, the contact opens and thus outputs a signal to the control. Terminal assignment 1 2 1 2 Maximum filling level Minimum filling level Technical Data (For applications outside these parameters, please consult us!) Maximum voltage V 50 AC/DC Maximum current consumption A 0.25 Maximum power consumption W 3.0 Protection class according to EN 60529 IP 65 Contact type Normally closed contact
14/16 Bosch Rexroth AG Hydraulics UPE 5 RE 51145/06.12 Temperature switch (option) Function By means of the temperature switch, the drive module is protected against operation with inadmissibly high hydraulic fluid temperatures. The temperature switch has a fixedly set switching point switching at a hydraulic fluid temperature of 70 C. The switch-back hysteresis is ca. 15 K. The temperature switch is screwed into port T2 in the tank. Terminal assignment 1 2 1 2 Temperature 70 C Temperature > 70 C Technical Data (For applications outside these parameters, please consult us!) Maximum voltage V 230 Maximum current consumption A 2 Protection class according to EN 60529 IP 65 Contact type Normally closed contact Oil tray (option) (dimensions in mm) Material no. R901271094 Color: RAL 7035 "Light gray" 100 200 25 710 4 x Ø11 500 750 800 376 94 355 315 640 162
RE 51145/06.12 UPE 5 Hydraulics Bosch Rexroth AG 15/16 Commissioning information Check whether the drive module has been professionally connected to the machine to be operated (hydraulically and electrically). For the electrical connections of the motor, the washers and connection bridges included in the delivery must be used. The electric motor must be protected by equipment with overload relay. The latter must be set to the rated current that is specified on the name / rating plate. When installing the drive module, the motor's direction of rotation must imperatively be observed, see arrow for direction of rotation. (Practical control: Hold a sheet of paper close to the cooler. It must be sucked in.) Only fill in the hydraulic fluid through a filter with the required minimum retention rate. Fill the drive module maximally to the upper edge of the inspection glass. The pump must in no case be operated without hydraulic fluid. Start up the pump without load and allow it to run at zero pressure for some seconds in order to provide for sufficient lubrication. The drive module may only be operated with the admissible data. It may moreover only be operated if it is in an unobjectionable condition. When carrying out works at the drive module, the system must be depressurized and de-energized. Unauthorized conversions or modifications which affect the safety and function are not permitted. Available protective devices must not be removed. The generally valid safety and accident prevention regulations must be observed and complied with. Keep the oil-air cooler clean and do not cover it as otherwise, the hydraulic fluid and the electric motor may overheat. The operating pressure of the oil-air cooler must not be exceeded. Attention! The drive module may heat up during operation Risk of injury! Settings, maintenance and service works at the drive module may only be carried out by authorized, trained and instructed personnel.
16/16 Bosch Rexroth AG Hydraulics UPE 5 RE 51145/06.12 Notes Bosch Rexroth AG Hydraulics Zum Eisengießer 1 97816 Lohr am Main, Germany Phone +49 (0) 93 52 / 18-0 Fax +49 (0) 93 52 / 18-23 58 documentation@boschrexroth.de www.boschrexroth.de This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be reproduced or given to third parties without its consent. The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging.