INSTALL GUIDE DOCUMENT NUMBER 864 REVISI DATE 77 FIRMWARE OEM-CH(RS)-CH4-[ADS-CH4] HARDWARE ADS-CH4 ACCESSORIES ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 7 BEFORE INSTALLATI - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
PAGE OF 8 DOC.: #864 77 VEHICLE LIST - OF PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX IGNITI CTRL RAP SHUTDOWN CTRL HOOD STATUS (W/OEM SW) DOOR STATUS BRAKE PEDAL STATUS TACHOMETER STATUS SECURE TAKEOVER PARKING LIGHT CTRL* 00c AT -0 00c SRT8 AT -0 Town & Country AT -6 Caravan AT -0 Challenger SXT AT -4 Challenger R/T AT -4 Challenger SRT8 AT -4 Charger SE AT -0 Charger R/T AT -0 Charger SRT8 AT -0 Durango AT - Grand Caravan AT -7 Journey AT 09-0 Magnum AT Commander AT -0 Grand Cherokee AT - C/V AT 0-5 500 AT 0-500 AT 0-500 AT 0-4500 AT - 5500 AT - Routan AT 09- POWER SLIDING DOOR (R) X LOCK /STANDALE MOD. -0 POWER SLIDING DOOR (L) DATA IMMOBILIZER BYPASS -0 00 Limited AT POWER LIFTGATE YEAR 00 AT INSTALL TYPE MODEL VW RAM JEEP DODGE CHRYSLER MAKE FEATURES * May require additional parts. Automotive Data Solutions Inc. 7
PAGE OF 8 DOC.: #864 77 BOX CTENTS - OF BOX CTENTS MODULE LED BLUE BLACK BLACK 0 PIN CNECTOR T-HARNESS 4 6 5 4 6 8 0 4 6 8 0 5 7 9 5 7 9 4 6 8 0 5 7 9 PROGRAMMING BUTT LED A G F B E 4 BLACK RF PORT/ WEBLINK PORT 4 BLUE TELEMATIC PORT BLACK MS VS PIN CNECTOR VS MS AFTERMARKET HOOD SWITCH AND CABLE C D 9 0 7 8 5 6 4 WHITE WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE Automotive Data Solutions Inc. 7
PAGE 4 OF 8 DOC.: #864 77 CHRYSLER 00C 00 SRT8 Town & Country Town & Country Caravan Challenger R/T Challenger SXT Challenger SRT8 DODGE Charger SE Charger R/T Charger SRT8 Durango Grand Caravan Grand Caravan Journey Magnum -0-0 -0-6 -0-4 -4-4 -0-0 -0 - -0-7 09-0 Automotive Data Solutions Inc. 7 POSITI WIRE COLOR POLARITY MODULE LOCATI COMPENT LOCATOR -0 CNECTOR TYPE 00 Limited CNECTOR COLOR -0 0 pin 0 pin CNECTOR NAME YEAR 00 WIRE DESCRIPTI MODEL MAKE TYPE - WIRE CHART - OF 0 pin 0 pin 0 pin 6 pin White/Green 0 pin 0 pin 0 pin 0 pin 0 pin 0 pin 0 pin 6 pin White/Green 0 pin 6 pin White/Green White/Violet (+) 0 pin
PAGE 5 OF 8 DOC.: #864 77 500 4500 VW 5500 Routan 0-0- - - 09- Automotive Data Solutions Inc. 7 COMPENT LOCATOR 500 0- MODULE LOCATI RAM 500-5 POLARITY C/V 0 WIRE COLOR C/V - POSITI Grand cherokee -0 CNECTOR TYPE Grand cherokee CNECTOR COLOR YEAR -0 CNECTOR NAME MODEL Commander WIRE DESCRIPTI JEEP MAKE TYPE - WIRE CHART - OF Pin # of relay #7 Power module in engine compartment Pin # of relay #7 Power module in engine compartment 0 pin Driver door module 0 pin White/LtGreen, door harness 0 pin 6 pin White/Green 0 pin White 0 pin White 0 pin White 0 pin White 0 pin White 0 pin
PAGE 6 OF 8 DOC.: #864 77 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITI SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT A VS IGNITI CNECTOR E C D A VS IGNITI HARNESS A 4 6 5 4 6 8 0 4 6 8 0 5 7 9 5 7 9 MS B A MS VEHICLE WHITE/GREEN (NC) WHITE/RED (NC) WHITE/BROWN - PARKING LIGHT OUTPUT PARKING LIGHT CNECTI CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT PARKING LIGHT OR C 4 6 5 8 7 0 9 CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT BROWN/BLACK - PARKING LIGHT OUTPUT GRAY - RAP SHUTDOWN OUTPUT 0 AMPS PARKING LIGHT V (+) OR GRAY/GREEN - HORN OUTPUT CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT (+) D 85 87 86 87A 0 4 6 8 0 5 7 9 PARKING LIGHT (+) GRAY/WHITE - HOOD STATUS INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CNECT TO AFTERMARKET HOOD SWITCH OPTIAL DRIVER DOOR PIN HORN AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc. 7
MODULE PROGRAMMING PROCEDURE - STD KEY - OF Close driver door. 07 Turn key to position. ACC Re-open driver door to wake up data bus. Remove key. ACC Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. Turn key to position. 0 Wait, LED will turn solid GREEN for seconds. LED will turn solid RED. Module Programming Procedure completed. 06 Within 5 seconds, LED will flash GREEN rapidly. ACC ACC PAGE 7 OF 8 DOC.: #864 77 Automotive Data Solutions Inc. 7
MODULE PROGRAMMING PROCEDURE - PTS - OF Close driver door. 07 Press UNLOCK on the OEM remote. Re-open driver door to wake up data bus. Wait, LED will turn solid GREEN for seconds. DO NOT PRESS BRAKE PEDAL. Push start button twice [x] to position. 09 Module Programming Procedure completed. STOP ACC PAGE 8 OF 8 DOC.: #864 77 ENGINE STOP LED will turn solid RED. Within 5 seconds, LED will flash GREEN rapidly. 06 STOP ACC DO NOT PRESS BRAKE PEDAL. Push start button once [x] to position. ENGINE STOP Automotive Data Solutions Inc. 7
VALET MODE PROGRAMMING PROCEDURE - OF NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Time restriction. Complete next step within 7 seconds. ACC PAGE 9 OF 8 DOC.: #864 77 To exit valet mode: repeat steps to 5. Cycle ignition five times [5x /] rapidly. ENGINE STOP Wait, LED will turn solid RED for seconds. Set ignition to position. ACC ENGINE STOP Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 7
PAGE 0 OF 8 DOC.: #864 77 MODULE NAVIGATI PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. Module must be programmed to the vehicle. Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 ACC TO ACCESS THE OPTIS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATI. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STOP [X] Automotive Data Solutions Inc. 7
PAGE OF 8 DOC.: #864 77 [Y] OPTIS [X] MENUS MODULE NAVIGATI CHART: NOTES I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. DISARM/UNLOCK BEFORE RELOCK AFTER RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL FIRST PRESS TAKEOVER 06 07 [Z] SETTINGS MODULE NAVIGATI CHART - OF FACTORY KEYLESS RS SEQUENCE CFIGURATI 09 MODULE RUN TIME WAIT TO DELAY ENABLE DISABLE* DISABLE LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK MIN MIN 0 MIN 5 MIN 5 MIN 06 0 MIN 07 5 MIN 5 MIN SEC SEC SEC 0 SEC 5 SEC 06 0 SEC 07 5 SEC 0 SEC 0 *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 7
PAGE OF 8 DOC.: #864 77 [Y] OPTIS [X] MENUS MODULE NAVIGATI CHART: NOTES 4 [Z] SETTINGS MODULE NAVIGATI CHART - OF HORN EVENT TRIGGER CFIGURATI 5-07 Technical Support only HORN CHIRPS WIDTH DOUBLE LOCK LOCK + UNLOCK LOCK + UNLOCK + DOUBLE LOCK + 0 msec 5 msec 60 msec *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 7
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE ER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. Foot brake is. Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 0 4 5 6 CAN communication failure during RS sequence. REMOTE ER ERROR CODES: NOTES Automotive Data Solutions Inc. 7 PAGE OF 8 DOC.: #864 77
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITI Automotive Data Solutions Inc. 7 DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE 4 OF 8 DOC.: #864 77
MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the BLACK 0-PIN connector. 07 Reconnect all connectors. Disconnect the BLACK 0-PIN connector. Repeat programming procedure. PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED will flash RED. RELEASE programming button. LED will turn RED for seconds. 06 Module RESET completed. Automotive Data Solutions Inc. 7 PAGE 5 OF 8 DOC.: #864 77
TAKEOVER PROCEDURE - STD KEY - OF All vehicle doors must be closed and locked prior to remote start sequence. Press unlock on OEM or aftermarket remote. Insert key into ignition. ACC Failure to follow procedure will result in vehicle engine shutdown. PAGE 6 OF 8 DOC.: #864 77 Turn key to position. ACC Press and release BRAKE pedal. Take over procedure completed. Automotive Data Solutions Inc. 7
TAKEOVER PROCEDURE - PTS - OF All vehicle doors must be closed and locked prior to remote start sequence. Press unlock on OEM or aftermarket remote or request switch. STOP ACC PAGE 7 OF 8 DOC.: #864 77 DO NOT PRESS BRAKE PEDAL. Push start button twice [x] to position. Wait seconds for key validation. ENGINE STOP Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown. Automotive Data Solutions Inc. 7
INSTALLATI CHECKLIST - OF PAGE 8 OF 8 DOC.: #864 77 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. 4 Exit vehicle. 5 Installation checklist completed. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Automotive Data Solutions Inc. 7