SLS plissé SL22S plissé PLEATED BLIND english Technical Catalogue double-glazed unit mm 22 mm
dimensions technical specification SLS SL22S plissé System S 2 S SLS plissé SL22S plissé The pleated blind SLS or SL22S for use in double-glazed units, is manufactured in accordance with high technical specification and production standards. The pleated blind operation is achieved using magnetic attraction through the glass thereby guaranteeing the unit s hermetic seal. The external magnet contained in a removable handle, is attracted by magnetic force to an equivalent magnet located in the centre of the blind bottom rail located inside the DG unit. The raising and lowering operation is achieved by sliding the removable handle across the glass surface. The magnetic housing design incorporates small rollers and bearings allowing them to glide over the glass surface without friction thereby avoiding abrasion of the glass surface. The movement of the blind is guaranteed along 2 possible directions vertically (up / down) or 2 directions horizontally (left / right) at any unit / window inclination from horizontal (0 degrees) to vertical (90 degrees). Height 0 ~ 1.500 mm Width 0 ~ 1.0 mm Maximum glass thickness of the control side 6 mm Blind pack height 2% blind height + 47 mm PLEATED BLIND
1. technical features Magnetic drive components Acrylic resin casing, containing small plastic rollers and magnets. Neodymium-Iron-Boron rectangular shaped magnets the following technical features: Energy produced Bh max-mg.0e 33-35 Residual induction Br-Gauss 11.000 /.000 Coercive force Hc-Oestered 10.000 Maximum working temperature C 0 Curie temperature C 310 Reversible temperature factor C -0.% Head rail Extruded aluminium, A6063S-T5 alloy. Dimensions: width 18 mm, height 24 mm including pelmet. Powder coated to aluminium grey colour. Includes interlocking design mechanism for easy and quick assembling of head rail and bottom rail to the upper and lower U-profile spacer bar. Verosol fabric Woven polyester fabric, 14 mm pleat, with an aluminium microfilm applied through an exclusive vacuum coating technique (three-chamber system). The microfilm adhesion complies with the EN-ISO 7523 and the fabric is Class 1 (one) Flame-Retardant - 6 colours are available. Vanity fabric Woven polyester fabric, 14 mm pleat, non flame retardant, not metallized. Colours available: 2. Performance characteristic of the Verosol fabric Pleated Verosol Solar Light Solar Solar Light Fabric reflecion % reflection % absorption % transmission % transmission % 8 71 66 9 9 816 52 50 28 22 875 74 74 21 5 5 Performance characteristic of the Vanity fabric Pleated Vanity Light reflection % Light absorption % Light transmission % Fabric White C000 46 4 51 Cream C010 40 13 46 Extruded aluminium A6063S-T5 alloy. Dimensions: width 14 mm, height 27 mm with recess for the internal magnet. Powder coated to aluminium grey colour. 3
SLS plissé SL22S plissé PLEATED BLIND technical specification SLS SL22S plissé Cords Thermo-fixed 100% polyester with internal core and with excellent dimensional stability. 1.0 mm diameter internal cord with centre core - white. Spacer bar Extruded aluminium. Available in two versions for each system: SL: U profile spacer bar dimension x 6.5 mm with 2 mm projection; L profile spacer bar x 6.5 mm with 8 mm projection. SL22: U profile spacer bar dimension 22 x 6.5 mm with 2 mm projection; C profile side guide 22 x 6.5 mm with 8 mm projections. 4
2. technical drawings SLS plissé comprehensive drawing with component codes For the system SL22S plissé SL1772 Extruded C shaped spacer bar 22 x 6.5 mm SL1773 Extruded U shaped spacer bar 22 x 6.5 mm SL18 Plastic corner key 22 x 6.5 mm SL1170 - SL1171 SL1680 SL1680 SL1172 - SL00 Adhesive plastic tape Adhesive mm plastic tape mm Pleated fabric 14 mm SL1740 SL1740SL1154 SL1542 SL1154 SL1542 Extruded L shaped Extruded Ladder L tape shaped Extruded Ladder tape U shaped Extruded U shaped spacer bar x 6.5 spacer mm fixing bar plug x 6.5 mm spacer fixing bar plug x 6.5 mmspacer bar x 6.5 mm SL1806 Cord brake SL1806 Cord brake SL1734 Steel corner key x SL1734 6.5 mm Steel corner key x 6.5 mm SL1554 end cap SL1555 Cord lock SL1554 end cap SL1560 Cord counter device SL1555 Cord lock SL1559 Internal magnetic device SL1538 SL1560 Cord counter device SL1537 Head rail SL1556 Cord spring SL1538 SL1170 - SL1171 SL1172 - SL00 Pleated fabric 14 mm SL1558 External magnetic handle SL1559 Internal magnetic device SL18 Plastic corner key 22 x 6.5 mm SL1773 Extruded U shaped spacer bar 22 x 6.5 mm SL1537 SL1557 Head rail Head rail end cap SL1165 Polyester cord 1 mm SL1557 Head rail end cap SL17 plastic label SL1556 Cord spring SL1558 External magnetic handle SL1557 Head rail end cap SL1165 Polyester cord 1 mm SL1557 Head rail end cap SL17 plastic label SL1772 Extruded C shaped spacer bar 22 x 6.5 mm SLS SL22S pleated blind SLS plissé drawing with component codes SL22S plissé 5
W glass SLS plissé double-glazed unit H glass 2 24 24 OUT IN PLEAT 14 mm 6.5 6.5 2 EXTRUDED U SPACER BAR x 6.5 mm 8 EXTRUDED L SPACER BAR x 6.5 mm W glass 22 SL22S plissé double-glazed unit H glass OUT IN 14 mm PLEAT 6.5 24 2 24 6.5 2 EXTRUDED U SHAPED SPACER BAR 22 x 6.5 mm 8 EXTRUDED C SHAPED SPACER BAR 22 x 6.5 mm 6
rasing and lowering function W glass H glass 70 2 24 24 OUT IN 14 mm PLEAT 25 32 SLS plissé double glazing unit with magnetic control 7
SLS plissé 3. feasibility 4 W Width cm H 30 40 50 60 70 80 90 100 110 0 Height cm 30 40 W Width cm H 30 40 50 60 70 80 90 100 110 0 Height cm 30 40 5glass thickness 5 mm Monolithic glass thickness 4 mm Monolithic 50 60 70 80 90 100 110 0 130 140 150 50 60 70 80 90 100 110 0 130 140 150 6glass thickness 6 mm Monolithic W Width cm H 30 40 50 60 70 80 90 100 110 0 Height cm 30 40 50 60 70 80 90 100 110 0 130 140 150 Feasible Not feasible 8
Pellini S.p.A. via Fusari, 19 26845 Codogno (LO) ITALIA T. + 39 0377 466411 F. + 39 0377 437635 info@pellini.net SLS SL22S plissé MTL007 Edition 07.06 www.pellini.net visual design: stefanosiboni.it