INSTALL GUIDE DOCUMENT NUMBER 9 REVISION DATE 7 FIRMWARE AKX-IDS(RS)-BM-[ADS-BM] HARDWARE ADS-BM ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DIRECTED SMARTSTART & ADS-HRN(RS)-SM (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
PAGE OF 9 DOC.: #9 7 VEHICLE LIST - OF FEATURES REMOTE START FROM OEM REMOTES SECURE TAKEOVER** DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE PARKING LIGHT CTRL RAP SHUTDOWN CTRL TACHOMETER STATUS MONITORING BRAKE PEDAL STATUS MONITORING VSS STATUS MONITORING DOOR STATUS MONITORING TRUNK STATUS MONITORING HOOD STATUS MONITORING* - Series PTS AT*** - Series Coupe PTS AT*** - 5 Series PTS AT -0 6 Series PTS AT -0 M PTS AT M PTS AT*** - M Coupe PTS AT*** - M5 PTS AT -0 M6 PTS AT -0 X PTS AT*** - X5 PTS AT - X5 Diesel PTS AT - X5 M PTS AT 0- X6 PTS AT - X6 M PTS AT 0- Z PTS AT*** 09- Clubman PTS AT*** - Cooper PTS AT*** - Cooper Convertible PTS AT*** - Countryman / ALL- PTS AT - Coupe PTS AT*** - Paceman PTS AT Roadster PTS AT*** - * If equipped with a factory hood switch. ** If equipped with an electric E-brake and it is activated, vehicle will shudown when a door is opened during RS sequence. *** If equipped with the Confort Access System, the door handles will not be functional during RS sequence. INSTALL TYPE MAKE BMW MINI Automotive Data Solutions Inc. GLOW PLUG STATUS MONITORING YEAR Series PTS AT POWER LIFTGATE MODEL NOTES I This firmware covers Automatic Transmission (AT) vehicles only.
PAGE OF 9 DOC.: #9 7 BOX CONTENTS - OF BOX CONTENTS MODULE LED RED BLUE BLUE TELEMATIC PORT 6 8 0 5 7 9 WHITE 6 8 0 5 7 9 USB BLUE 6 5 6 8 0 6 8 0 5 7 9 5 7 9 6 5 EXPANSION PACK XP LED 0 PIN WHITE CONNECTOR T-HARNESS LED PROGRAMMING BUTTON PIN CONNECTOR AFTERMARKET HOOD SWITCH AND CABLE EXPANSION CABLE T-HARNESS RF PORT/USB PORT 8 PIN WHITE CONNECTOR - ADAPTER CABLE XP LED THE ADS-HRNBMW- CABLE IS INCLUDED IN KITS MANUFACTURED AFTER //. CONTACT YOUR AUTHORIZED DEALER, IF THIS CABLE IS NOT INCLUDED. EXPANSION PACK ASSEMBLY ADS-HRNBMW- LED LED STICKER STICKER 5 7 9 57 6 8 0 6 8 WHITE TOP VIEW BOTTOM VIEW TOP VIEW WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT PIN CABLE Automotive Data Solutions Inc.
PAGE OF 9 DOC.: #9 7 COMPATIBLE ACCESSORIES - 5 OF 5 RF KIT (Visit our website to see if this accessory is included with your product) RF KIT FLASH RF DECODER BEFORE INSTALLATION (NC) RED (NC) BLUE MODULE RF PORT BLUE CABLE RF DECODER CABLE ANTENNA TELEMATIC KIT (accessories sold separately) ADS-HRN(RS)-SM DIRECTED SMARTSTART (NC) MODULE TELEMATIC PORT (NC) (NC) Automotive Data Solutions Inc.
TECHNICAL NOTE - OF IMPORTANT PAGE 5 OF 9 DOC.: #9 7 INSTALL VIDEO GALLERY AVAILABLE ONLINE Before installing this product, consult our Install Video Gallery and watch: Vehicle Disassembly Procedure videos Module Connection Procedures videos Module Programming Procedures videos Simply visit our forum and register at http://www.voltdata.com/forum/viewtopic.php?f=0&t=968&sid=a677b86e58ad6f8b7ffa5 Automotive Data Solutions Inc.
PAGE 6 OF 9 DOC.: #9 7 MODULE INSTALLATION PROCEDURE - OF START vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle. Turn ignition to OFF position. Remove keyfob from keyport. Connect and secure every connector to the vehicle, as shown in STEP of the WIRING DIAGRAM. Connect the P connector to the module, as shown in STEP of the WIRING DIAGRAM. P WARNING: Any vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. An OEM scantool will be required to clear the error messages. If required, connect a compatible RF Kit, as shown in STEP of the WIRING DIAGRAM. RF F 0 Verify all keyfob functionalities (Door Lock, Door Unlock, Trunk Release and Comfort Access System if equipped). 09 Insert the expansion pack into module. 0 WARNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support. 6 If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP of the WIRING DIAGRAM. Use the EXPANSION CABLE to connect the A connector to the module and the O connector to the expansion pack. Turn ignition to OFF position. Remove keyfob from keyport. 7 Put sticker on a clean and visible surface in the engine bay and put sticker under the dashboard near the OBDII connector. Connect the module to the computer with the programming cable (F port). Flash the module with the latest firmware then flash the expansion pack. Connect the C connector to the module, as shown in STEP of the WIRING DIAGRAM. 8 Module installation procedure completed. O START vehicle. Verify all vehicle functionalities. 5 I If required, connect a compatible Telematics Device, as shown in STEP of the WIRING DIAGRAM. A C F Automotive Data Solutions Inc.
PAGE 7 OF 9 DOC.: #9 7 TYPE - WIRING DIAGRAM - OF STEP WARNING -TO CONNECT THE MODULE: FOLLOW STEPS TO -TO DISCONNECT THE MODULE: FOLLOW STEPS TO CONNECT THE FOLLOWING TO THE VEHICLE START THE VEHICLE WITH THE OEM KEYFOB TO TEST THE CONNECTIONS BRAKE SWITCH A BRAKE HARNESS MODULE STEP RELAY CONNECT TO MODULE COMFORT ACCESS SYSTEM MODULE 0 PIN C B MINI: BEHIND INSTRUMENT PANEL, DRIVER SIDE BMW: UNDER DASH, DRIVER SIDE B CONNECTOR WHITE 8 PIN B HARNESS RELAY STEP CONNECT TO MODULE PIN C CONNECTOR 6 PIN C HARNESS STEP WARNING: THESE CONNECTORS HAVE TWO [X] LOCKING MECHANISMS. INSERT THE CONNECTOR IN ITS HOUSING AND APPLY GENTLE PRESSURE ON BOTH EXTREMITIES TO SECURE THE CONNECTION. (TWO AUDIBLE CLICKS WILL BE HEARD.) CONNECT IF REQUIRED WHITE 0 PIN IF NOT EQUIPPED WITH AN OEM HOOD SWITCH, INSTALL AN AFTERMARKET HOOD SWITCH HOOD SWITCH GRAY/WHITE - HOOD STATUS (-) INPUT GRAY/ (NOT USED) Automotive Data Solutions Inc.
Paceman PTS AT Automotive Data Solutions Inc. MODULE LOCATION POLARITY WIRE COLOR POSITION CONNECTOR TYPE CONNECTOR COLOR CONNECTOR NAME WIRE DESCRIPTION MODEL MAKE YEAR - MINI Countryman / ALL- PTS AT COMPONENT LOCATOR PAGE 8 OF 9 DOC.: #9 7 TYPE - WIRE CHART - OF V X6 5 pin Red/Yellow (+) Driver kick panel Ground X6 5 pin 7 Brown or Brown/Black (-) Driver kick panel CanH X6 5 pin 6 Orange/Green (DATA) Driver kick panel CanL X6 5 pin 5 Green (DATA) Driver kick panel V X6 5 pin Red/Yellow (+) Driver kick panel Ground X6 5 pin 7 Brown or Brown/Black (-) Driver kick panel CanH X6 5 pin 6 Orange/Green (DATA) Driver kick panel CanL X6 5 pin 5 Green (DATA) Driver kick panel
PAGE 9 OF 9 DOC.: #9 7 TYPE - WIRING DIAGRAM - OF STEP WARNING -TO CONNECT THE MODULE: FOLLOW STEPS TO 5 -TO DISCONNECT THE MODULE: FOLLOW STEPS 5 TO CONNECT THE FOLLOWING TO THE VEHICLE START THE VEHICLE WITH THE OEM KEYFOB TO TEST THE CONNECTIONS BRAKE SWITCH A RELAY BRAKE HARNESS MODULE STEP STEP CONNECT TO MODULE CUT AND REMOVECONNECTORS FROM T-HARNESS 0 PIN X6 WHITE 8 PIN 5 AMPS STEP CONNECT TO MODULE CONNECT IF WIRE IS PRESENT RED PINK (NOT USED) PINK/RED PINK/YELLOW 5 6 7 8 5 6 9 0 5 6 7 8 9 50 5 WHITE 8 PIN ADAPTER CABLE V (+) - GROUND - 7 CANH - 6 CANL - 5 GROUND - 7 7 8 9 0 0 5 6 DRIVER KICK PANEL 7 8 9 0 5 6 7 8 9 X6 KEYPORT CONNECTOR PIN RELAY 8 5 6 7 9 0 6 PIN KEYPORT HARNESS STEP 5 WARNING: THESE CONNECTORS HAVE TWO [X] LOCKING MECHANISMS. INSERT THE CONNECTOR IN ITS HOUSING AND APPLY GENTLE PRESSURE ON BOTH EXTREMITIES TO SECURE THE CONNECTION. (TWO AUDIBLE CLICKS WILL BE HEARD.) CONNECT IF REQUIRED WHITE 0 PIN IF NOT EQUIPPED WITH AN OEM HOOD SWITCH, INSTALL AN AFTERMARKET HOOD SWITCH HOOD SWITCH GRAY/WHITE - HOOD STATUS (-) INPUT GRAY/ (NOT USED) Automotive Data Solutions Inc.
PAGE 0 OF 9 DOC.: #9 7 MODULE PROGRAMMING PROCEDURE - OF LED is solid RED. Insert keyfob into keyport. Remove keyfob from keyport. LED will turn solid GREEN for seconds. Within 0 seconds, LED will flash GREEN once (x). WARNING: Follow steps,, as shown in the wiring diagram to disconnect the module from the vehicle. Remove keyfob from keyport. 0 Remove keyfob from keyport. 09 Connect module to computer and proceed with KLON programming. 5 Module Programming Procedure completed. LED will turn solid RED. Wait 5 seconds. 0 WARNING: Follow steps,, as shown in the wiring diagram to connect the module to the vehicle. Insert keyfob into keyport. LED will turn solid RED. Within 0 seconds, LED will flash GREEN rapidly. Insert keyfob into keyport. Automotive Data Solutions Inc.
INSTALLATION CHECKLIST - OF PAGE OF 9 DOC.: #9 7 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventillated area. Open driver door window for easy vehicle access. 0 Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. QUESTION : Does the vehicle remote start? YES: Go to step 5. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connection, repeat step and call technical support if the problem persist. QUESTION : Does the vehicle shut down? YES: Go to step 6. Unlock and open driver door. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. NO: Repeat step 5. If problem persists, push vehicle start button once [x] to shut down the vehicle and call technical support. QUESTION : Does the vehicle remote start? YES: The module does NOT detect the door signal from the vehicle communication network. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle and call technical support. Open hood. NO: Go to step 8. QUESTION : Is the orange warning sticker "Sticker " placed under the hood? YES: Leave hood open and go to step 9. 09 Close all doors. 0 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. NO: Put the mandatory orange warning sticker "Sticker ", leave hood open and go to step 9. QUESTION 5: Does the vehicle remote start? YES: Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Go to Question 6. NO: Go to step. QUESTION 6: Is the vehicle equipped with a factory hood switch? (Inside hood latch) YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support. Close hood. Enter vehicle. Do NOT press brake pedal. Close all doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. 5 Wait for the vehicle to start. 6 Press brake pedal. NO: Install the mandatory hood switch included in the kit. Repeat installation checklist. QUESTION 7: Does the vehicle shut down? YES: Go to step 7. 7 Apply parking brake. 8 Exit vehicle. NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle and call technical support. Automotive Data Solutions Inc.
INSTALLATION CHECKLIST - OF PAGE OF 9 DOC.: #9 7 CHECKLIST 9 Close all doors. 0 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. QUESTION 8: Is the vehicle equipped with Comfort Access System? YES: For, 5, 6, X5, X6: Touch exterior driver door handle to unlock door using Comfort Access System. Within 5 seconds, go to step. YES: For, X, Z, Mini: Press UNLOCK button once [x] on the OEM keyfob. Within 5 seconds, go to step. NO: Press UNLOCK button once [x] on the OEM keyfob. Within 5 seconds, go to step. Open driver door. QUESTION 9: Does the vehicle shut down? YES: For Z, X5, X6: Go to step 5. YES: For,, 5, 6, X: The module does NOT detect the parking brake signal or the unlock signal from the vehicle communication network. Call technical support. NO: For Z, X5, X6: The module does NOT detect the parking brake signal correctly from the vehicle communication network. Call technical support. NO: For,, 5, 6, X: Go to step. Press and release brake pedal. Push vehicle start button once [x] to shut down the vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc.
VALET MODE PROGRAMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Remove keyfob from keyport. Insert keyfob into keyport. Valet Mode Programming Procedure completed. Time restriction. Complete next step within 5 seconds. >> To exit valet mode: repeat steps to 6. 0 STOP ACC ON START PAGE OF 9 DOC.: #9 7 Cycle ignition ON five times [5x OFF/ON] rapidly. Parking Light will flash once [x]. ENGINE START STOP Wait, Parking Light will flash once [x] to indicate that the valet mode is ON or twice [x] to indicate that the valet mode is OFF. Turn ignition to STOP position. STOP ACC ON START ENGINE START STOP Automotive Data Solutions Inc.
PAGE OF 9 DOC.: #9 7 AFTERMARKET REMOTE PROGRAMMING PROCEDURE - OF >> WARNING: Program aftermarket remotes before usage. A maximum of four [x] aftermarket remotes per system. Press once [x] on LOCK button of aftermarket remote. Insert keyfob into keyport. Parking Light will flash once [x]. Time restriction. Complete next step within 7 seconds. >> To program additional remotes: repeat steps 5 to 7 using each additional remote. Cycle ignition ON five times [5x OFF/ON] rapidly. Wait, Parking Light will flash twice [x]. Parking Light will flash once [x]. 09 0 STOP ACC ON START Aftermarket Remote Programming Procedure completed. ENGINE START STOP Turn ignition to STOP position. STOP ACC ON START ENGINE START STOP Time restriction. Complete next step within 5 seconds from previous step. Automotive Data Solutions Inc. 0 Remove keyfob from keyport.
PAGE 5 OF 9 DOC.: #9 7 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. >> Module must be programmed to the vehicle. >> Use the Module Navigation Chart on the next page. Set ignition to OFF position. TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 STOP ACC ON START TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 [X] Automotive Data Solutions Inc.
PAGE 6 OF 9 DOC.: #9 7 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES I Default settings are listed in bold. OFF ON OFF ON OFF ON OFF ON ENABLE DISABLE* 5 SEC 90 SEC 0 0 MIN MIN DISABLE N/A 0 LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK 0 MIN MIN 0 0 MIN 5 MIN 5 MIN 0 MIN 5 MIN 5 MIN SEC SEC 0 SEC 0 SEC 5 SEC 0 SEC 5 SEC 0 SEC 0-5 N/A N/A N/A II Make sure the option is covered on the vehicle before attempting to change the setting. 0 [Z] SETTINGS MODULE NAVIGATION CHART - OF DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS TAKEOVER SECURE TAKEOVER DELAY FACTORY KEYLESS RS SEQUENCE CONFIGURATION 09 - Technical Support only MODULE RUN TIME WAIT TO START DELAY N/A *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc.
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. Engine running. Key in ignition at ON position. II After a remote starter failure, the parking lights will flash three [x] times, then will flash [X] number times to indicate an error code. See table. 0 N/A Trunk is open. Foot brake is ON. Hood is open. N/A Tach failure. 09 N/A 0 System is in Valet Mode. CAN communication failure RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES: NOTES I WARNING: The following applies only when the parking lights are connected and supported by the system. Engine tach signal is lost. N/A II If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for.5 seconds when using a -WAY remote. OR Press once [x] on button when using a -WAY remote. 0 Foot brake is ON. Hood is open. Engine RPM limiter is ON. Glow plug timeout error. Vehicle is moving (VSS). Check engine warning light is ON. 09 Low fuel warning light is ON. 0 N/A CAN communication failure during RS sequence. REMOTE STARTER SHUTDOWN ERROR CODES: NOTES The parking lights will flash four [x] times, then will flash [Y] number times to indicate an error code. See table. Automotive Data Solutions Inc. PAGE 7 OF 9 DOC.: #9 7
I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Automotive Data Solutions Inc. DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. PAGE 8 OF 9 DOC.: #9 7
MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the 0-PIN connector. Reconnect all connectors. Disconnect the 0-PIN connector. Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED will flash RED. RELEASE programming button. LED will turn RED for seconds. Module RESET completed. Automotive Data Solutions Inc. PAGE 9 OF 9 DOC.: #9 7