CB 3 A car wash really can be both flexible and fast. A car wash really can be both fast and economical. And a car wash really can be both economical and versatile. The CB 3 unites these three qualities into one gantry car wash which can meet all requirements. 1 High-quality control system 3 Built-in high pressure pump The CB 3 s well-engineered control unit is compatible with Kärcher Fleet fleet management. The powerful high-pressure unit (1300 l/h 70 bar) is mounted on the system. Space-saving, since no additional technical room is necessary. 2 Water saving mode 4 Express wash for higher vehicle throughput The CB 3 needs 20 litres of fresh water per run. Cost reduction for the operator. A high vehicle throughput is possible thanks to the quick wash program. Very low or no waiting times increase customer satisfaction.
TECHNICAL DATA AND EQUIPMENT CB 3 Technical data Order no. EAN code 4039784987869 Washing height mm 2300 Height of system mm 3215 Width of system mm 3500 Fresh water connection, volume l/min 50 Fresh water connection, pressure bar 4 / 6 Voltage V 400 Frequency Hz 50 Number of current phases Ph 3
Control cable Control cable 3 x 1.5 mm² 1 6.641-059.0 Connecting cable 3 x 1.5 mm². Available by the meter. Available accessories.
Water recycling Add-on kit tank recycling water 1 2.642-720.0 1000 l Add-on kit box add-on 2 2.642-930.0 Pipelines kit 2000 l 3 4.640-401.0 Pipelines kit 3000 l 4 4.640-402.0 Control cable pump pit - WRP 5 6.647-276.0 Control cable for connecting the pump storage basin to the WRP system control cabinet. Available by the meter. Available accessories.
Travel rail extensions 2x 1 m travel rail extension set 1 2.640-460.0 1 m travel way. Hot-galvanised special profile, 40 mm mounting height. The scope of delivery includes mounting and supporting material. The travel rails are directly fixed to the ground. The length of the travel rails depends on the length of the vehicles to be washed. The length is calculated by adding to the length of the longest vehicle to be washed approx. 6 m (for machine movements). The standard length of buses are 12 m and trucks are approximately 18 m long. Frost protection Extension reclaimed water 2 2.642-586.0 Water pressure increase system Supply pump module 3 2.641-991.0 The plant can be equipped with a water pressure increase system if the supply pressure on site is too low. The pump provides the plant with the required flow pressure of 4-6 bar. Water tank 1000 l 4 2.642-501.0 Labels wash height / drive through width Label wash height 2.30 m 5 5.393-102.0 The labels are attached to car portal washing stations with a washing height of 2.30m to indicate the max. washing height. Label wash height 2.50 m 6 5.393-103.0 The labels are attached to car portal washing stations with a washing height of 2.50m to indicate the max. washing height. Label wash height 2.80 m 7 5.393-104.0 The labels are attached to car portal washing stations with a washing height of 2.80m to indicate the max. washing height. Label: Drive-through width: 2.25 m 8 5.393-106.0 Label for making clear to drivers the maximum drivethrough width of 2.25 m in the gantry car washes from Kärcher. Label: Drive-through width: 2.30 m 9 5.393-980.0 Label for gantry car washes as a warning notice to drivers of the maximum drive-through width of 2.30 m. Operation panel "Basic" control section 10 3.812-320.0 It is a very simple version covering the basic needs. Wash programs are selected via pressing single buttons or button combinations. The unit is equipped with an "emergency switch-off", a "start"-button and a "basic-position"-button. We suggest to install it in combination with a wash card reader to support the general automatic wash, for example if a special vehicle needs to be washed. The control panel allows manual interventions e.g. brush movements, during the automated washing process. Free length of cable is 10 m measured from the distribution device installed in the technical room. Washing programs max. 7 Advanced remote control 11 4.812-125.0 Remote control for gantry car washes, which are recommended where the system is operated by staff. This allows the operator full access to all washing programmes and other functions. Brushes PE brushes 12 2.640-831.0 The PE brushes are made of single bristles with a diameter 13 2.640-832.0 of approx. 0.7 mm. The brush material assures a very good 14 2.640-833.0 and efficient cleaning result. Available accessories.
16 18 Disc brush set Ø 450 mm, standard design Brush Ø450, Radkastenr., RAL 9005 Disc brush set Ø 380 mm, standard design 15 2.641-451.0 Brush set consisting of PE brushes in standard Kärcher yellow/black design, required for wheel washing brushes (disc brushes with a diameter of 450 mm) in gantry car washes. 16 2.641-452.0 Brush set consisting of PE brushes in black, required for wheel washing brushes (disc brushes) with a diameter of 450 mm in gantry car washes. 17 2.643-431.0 The wheel washing brushes (disc brushes with a diameter of 380 mm) in our gantry car washes require these brush sets, which consist of PE brushes in a standard Kärcher yellow and black design. Disc brush set Ø 380 mm, black 18 2.643-600.0 Brush set required for wheel washing brushes (disc brushes) on gantry car washes. The brush sets consist of PE brushes in black and have a diameter of 380 mm. Energy supply Extension energy support / cable drag chain 19 2.640-975.0 The extension kit is an adapter for additional hoses. It is necessary if the unit will be equipped with high pressure. The kit is designed for the HP-hose and two additional hoses. Hot galvanised support 20 2.640-980.0 One massive, hot galvanised column or a wall bracket for getting the power as well as the water and air hoses connected to the gantry. The single support guarantees easy and quick installation of the power supply. In general it is suited for an outdoor installation. Festooned cable, wall mounted 21 2.850-690.0 The energy supply of power as well as the water and air hoses is housed in a festooned cable. It consists of a solid, hot-dipped galvanised C-profiled rail guiding the travelling carriage. The re-quired cables and hoses are fixed to the travelling carriage. The rail is fixed to a lateral wall with hot-dipped galvanised brackets. The festooned cable can only be fixed to a wall and therefore only used in washing halls. Length 9 m. Hot galvanised support 22 2.850-711.0 One massive, hot galvanised column or a wall bracket for getting the power as well as the water and air hoses connected to the gantry. The single support guarantees easy and quick installation of the power supply. In general it is suited for an outdoor installation. Front doors Add-on kit doors complete Ampel links Add-on kit doors complete Ampel rechts Add-on kit doors complete Ampel rechts u Add-on kit doors complete Ampel - Wasch 23 2.643-010.0 The "Deluxe" front doors are made from a high-quality plastic in RAL 7012 and RAL 1018. With 3-field LED positioning lights, to the left in the direction of entry. 24 2.643-011.0 The "Deluxe" front doors are made from a high-quality plastic in RAL 7012 and RAL 1018. With 3-field LED positioning lights, to the right in the direction of entry. 25 2.643-012.0 The "Deluxe" front doors are made from a high-quality plastic in RAL 7012 and RAL 1018. With 3-field LED positioning lights on the left and right. 26 2.643-013.0 The "Deluxe" front doors are made from a high-quality plastic in RAL 7012 and RAL 1018. With 3-field LED positioning lights on both sides, incl. wash phase symbol lights. Vehicle positioning Treadle plate, mechanical 27 2.640-955.0 Frost protection system Extension 60 bar HP 28 2.641-095.0 Available accessories.
Extension manual frost protection pre-spraying rims / intensive pre-wash complete / spot-free rinsing Extension automatic frost protection pre-spraying rims / intensive pre-wash complete / spot-free rinsing 29 2.641-154.0 Prevents the plant and vehicles from suffering any damage There are two options regarding the frost protection: With a manual switch the operator gives the signal to blow out the basic machine. 30 2.641-155.0 Prevents the plant and vehicles from suffering any damage There are two options regarding the frost protection. Assembly plate frost protection 31 2.641-258.0 Expansion: automatic frost protection HP 60 bar Expansion: automatic frost protection HP 100 bar 32 2.642-845.0 Winter damage to the system can be reliably prevented with the automatic 60 bar frost protection. This process involves compressed air which effectively dries the water-bearing parts. 33 2.642-854.0 By blowing compressed air through feed pipes, water distributors and spray lances, the automatic 60 bar frost protection prevents damage caused by low temperatures. 34 2.643-329.0 Automatic frost protection HP 100 bar: Controlled by a thermostat, feed pipes, water distributors and the spray pipes located on the system are all blown through using compressed air. 35 2.643-330.0 The automatic HP 100 bar frost protection is controlled via a thermostat and protects the system against winter damage by blowing compressed air through water-bearing parts. Automatic frost protection 36 2.850-718.0 Prevents the plant and vehicles from suffering any damage There are two options regarding the frost protection: A thermostat monitors the temperature. In case of frost it gives the signal to start the process. Available accessories.
Frost protection manual 37 2.850-722.0 Prevents the plant and vehicles from suffering any damage There are two options regarding the frost protection: With a manual switch the operator gives the signal to blow out the basic machine. Extension of automatic antifreeze, process water mode Extension of manual antifreeze, high-pressure, side / underbody wash 38 2.850-726.0 Prevents the plant and vehicles from suffering any damage There are two options regarding the frost protection: A thermostat monitors the temperature. In case of frost it gives the signal to start the process. 39 2.850-727.0 Prevents the plant and vehicles from suffering any damage There are two options regarding the frost protection: With a manual switch the operator gives the signal to blow out the basic machine. Pumps 60 bar high-pressure pump 40 2.640-973.0 Rugged high-pressure pump module consisting of two crankshaft pumps. Suitable for supply of gantry car washes with 60 bar high pressure and for both fresh and reclaim water. High-pressure pump HD-E 60/6 K2 li 41 2.641-126.0 Crank shaft high-pressure pump unit mounted on a rack including control cabinet. Power 3~ / 400 V / 50 Hz ABS tank plastics HD Modul CB 42 2.851-053.0 Fresh water tank module with a capacity of 210 litres for supplying water to portal washing stations. It is installed on the pump module. Supply valve included. Guide rails Wheel guides 43 2.642-324.0 Hot-dip galvanised wheel guides that enable customers to correctly position their vehicle. Can be used for all wheel washing units and wheel rims up to 21 inches. 44 2.642-325.0 Can be used for all wheel washing units and wheel rims up to 21 inches: these hot-dip galvanised and painted wheel guides help your customers to position their vehicle correctly. Available accessories.
Speed Stop 45 4.651-002.0 Our Speed Stop wheel guides help your customers to enter the washing bay centrally. Safety devices Add-on kit safety switch positioning CB5 46 2.642-991.0 The "Too wide vehicle" safety device for car portal washing stations ensures that the required safety distances are observed. Add-on kit switch hall too narrow 47 2.642-992.0 The "Too short bay entrance/front" safety device for car portal washing stations ensures that the required safety distances are observed. Under chassis wash Under chassis wash with segment control Pump connector kit, underbody wash 48 2.641-087.0 The two high-pressure tubes of the under-chassis wash are divided in three identical segments. Depending on the length of the vehicle segments are switched on, one after another. The under chassis wash unit removes dirt adhering to the under chassis of the vehicle to be washed. Two high-pressure tubes made of stainless steel are integrated within an under chassis wash aggregate. Their swivelling movements enlarge the cleaning surfaces on the under chassis of the vehicle. The swivelling of the tubes is carried out by a maintenance-free pneumatic cylinder. The unit can be installed in or above the floor. The basic frame is hot galvanised. The panelling is corrugated aluminium to prevent slipping. 49 2.641-215.0 If the medium pressure pump is used for the under chassis wash then this kit delivers everything for connecting the two components. The under chassis wash unit removes dirt adhering to the under chassis of the vehicle to be washed. Two high-pressure tubes made of stainless steel are integrated within an under chassis wash aggregate. Their swivelling movements enlarge the cleaning surfaces on the under chassis of the vehicle. The swivelling of the tubes is carried out by a maintenance-free pneumatic cylinder. The unit can be installed in or above the floor. The basic frame is hot galvanised. The panelling is corrugated aluminium to prevent slipping. Under chassis wash fixed 16 bar 50 2.642-399.0 Add-on kit subsoil washing low 51 2.642-400.0 cost 6MPa Switch valve HP-unit / UCW 52 2.642-454.0 The "High-pressure undercarriage wash (HD/UBW) changeover valve" attachment kit enables the supply of water for undercarriage and high-pressure washing for car portal washing stations via the same pump. Covering elements Add-on kit covering front quer 53 2.642-995.0 The front trim is attached in front of the roof brush and completes the look and feel of the car portal washing station. Ideal for washing bays at locations with brisk public traffic. Add-on kit covering rear quer 54 2.642-996.0 The rear trim conceals the side brush girders and is recommended for outside installations and installations in drivethrough bays at locations with brisk public traffic. Add-on kit ticker 55 2.643-179.0 Front trim for car portal washing stations with customisable, easy-to-read moving LED display (ticker). Available accessories.
63 67 68 Add-on kit covering high-pressure Onboar 56 2.643-500.0 The Deluxe base cladding made of yellow plastic plates (RAL 1018) with design contours is easy to mount on the gantry frame of the CB 3 gantry car wash with a washing height of 2.80 m. 57 2.643-501.0 For mounting on the CB 3 gantry frame (washing height 2.50 m): the Deluxe base cladding made of yellow plastic plates (RAL 1018) with design contours. 58 2.643-502.0 Completes the CB 3 gantry car wash (washing height 2.30 m): the Deluxe base cladding made of yellow plastic plates (RAL 1018) with design contours. 59 2.643-506.0 The Basic base cladding consists of smooth, anthracite-coloured plastic plates (RAL 7012), which can be attached to the gantry frame of the CB 3 (washing height 2.80 m) with a clip closure. 60 2.643-508.0 The Basic base cladding completes the gantry frame of the CB 3 (washing height 2.30 m) with smooth, anthracite-coloured plastic plates (RAL 7012). Covering side bottom Deluxe CB3 61 2.643-512.0 The lateral bottom sections of the Deluxe base cladding are made of yellow plastic plates (RAL 1018) with design contours. Available for left and right sides. Covering side basic CB 3 62 2.643-516.0 The lateral bottom sections of the Basic base cladding made of smooth, anthracite-coloured plastic plates (RAL 7012) can be mounted on the gantry frame of the CB 3 with a clip closure. Wash card reader / pin coder reader Interface for self serve starting device including key switch Water reclamation systems Changeover osmosis engineering room 63 2.641-014.0 The "interface" is a prerequisite for connecting a wash card reader to the system. The various operating states are selected via the key-operated switch. Position 0: System off (end of operating time) Position 1: no manual programme start possible On the control section only manual interventions and functions are available. The wash programmes can be started only with the wash card reader Position 2: Programme start via control section and card reader possible This position allows programme start via the wash card reader and the control section. In addition all manual functions are available on the control section. 64 2.643-177.0 With the "Osmosis" washing programme option, all mineral deposits are removed by a rinse process using osmosis demineralised water. For a stain-free surface with no grey film. Additional controls Signal distributor 65 3.812-371.0 Signal distributor for ensuring a functioning connection to existing pump engineering and water reclamation systems. UBW external attachment kit 66 4.812-056.0 Attachment kit for gantry car washes for the control of an undercarriage washing station with a sheathed cable, already present at the customer's premises. Can patch cable 20 m 67 6.649-618.0 Communication line between feed distributor which is installed Can patch cable 50 m 68 6.649-619.0 at the energy chain and other components like frost protection and door control that are mounted in the technical room. Available accessories.
78 Remote control RDS I (Remote Diagnostic System I) 69 2.641-363.0 RDS I is a system for transmitting information on faults which may occur in the plant. All codes stored in the fault memory can be sent to an email address (master) and additionally up to 10 predetermined addresses by SMS (short message service). A predetermined main number has access to the plant's total daily and total wash counters. The system operates with standard SIM (subscriber identity module) cards of all dual band network operators. Side dryer Side blower air vent cover 70 5.056-058.0 Cover for side blower ducts in gantry frame. Gate control Basic gate control 71 2.641-776.0 Basic gate control is a basic transducer for gate opening and closing functions and can be adapted to any gate already installed on the premises. Extension gate control basic, gate 72 2.641-777.0 no. 1 Expansion of basic gate control, gate no. 2 73 2.641-778.0 Light barriers for drive-through check: optional expansion of the gate control of the second gate of the gantry car washes. Thermostat 74 2.641-950.0 Thermostat for precise regulation of the ambient temperature. Depending on the values measured, the gate remains open or is closed automatically when temperatures become too low. Cable for thermostat 75 6.641-122.0 Power cable connecting the thermostat for temperature-dependent operating mode switching to the gate control. Water pressure boost 50/3 supply pump module 76 2.643-485.0 Supply pump module for consistently guaranteeing the required flow pressure (3-6 bar) and the water volume (50 l/min) for Kärcher's CB 3 gantry car washes. 100/4.8 supply pump module 77 4.540-007.0 This supply pump module ensures both a constant flow pressure of 4 to 6 bar and a water volume of 100 l/min during the operation of gantry car washes. Payment systems Start/payment system CR 214 78 2.643-856.0 Available accessories.