Blohm + Voss B+V hinged Adapter 49 /2 to 37 /2 for RT National Inspection and maintenance procedure Part No. 55320
Blohm+Voss Oil Tools Hermann-Blohm-Straße 2 20457 Hamburg Germany Telephone ++49 (0)40/39-826/62 Fax ++49 (0)40/39-894 Revision date: 202 All rights retained. No part of this document may be reproduced in any form (print, photocopy, microfilm or any other procedure)or be processed using an electronic system without written approval of Blohm+ Voss Oil Tools Dependent on ongoing technical improvements (ISO 900) B+V Oil Tools reserves the right to be able to change the design and specifications without previous announcement. The values specified represent the nominal values of a unit produced in series production. Slight deviations in the case of the individual devices are possible. 2
Content Service, Maintenance and Parts... 4. Description...4 2. Installation Procedure...4 3. Maintenance and Inspection...5 4. Parts...6 5. Address List...7 3
Service, Maintenance and Parts. Description The adapter is available for 49 / 2 " rotary tables of the type NATIONAL and belongs to our adapter family. MPCH, split casing bushing, power slips can be used with this adapter. The adapter is inserted directly into the rotary table. This ensures that the casing being run is perfectly aligned with the center of the hole. Adapter 55320 can be used together with adapter 553220. It is possible to reduce the diameter of 60 / 2 down to 37 / 2 2. Installation Procedure 3 4 2. Inspect the top side of the rotary table bore for damaged edges. Chamfer as required to allow the adapter to enter the rotary table freely. Clean and grease the inside surface of the rotary table. 2. Inspect the blocks () and screws with the retaining rings (2) which secure the screws. If the screws are loose, they must be screwed down. The blocks must fit well in the adapter. 3. Inspect the hinges and lifting eyes (3)(4) before the adapter is to be lifted. 4. Screw down the lifting eyes and inspect them before using. 5. Engage lifting sling hooks in the lifting eyes (4) provided in the adapter, lift and lower into the rotary table. 6. After the adapter has been fitted in the rotary table, the lifting eyes have to be removed. This provides proper and safe work with this adapter 4
3. Maintenance and Inspection. Clean and remove abrasive material from inside of the adapter. Use a disc grinder to remove any rough surfaces or gall marks. 2. Remove, clean and lubricate the hinge pins after using the adapter. 3. Inspect all edges of the blocks () and their fit in the adapter. 4. Regularly inspect the condition of the hinge pins (crack or other wear) 5. The adapter should be well cleaned and painted before it will be stored. 5
4. Parts Pos. 2 stick in with Loctite 6 7 8 9 2 Stempelfeldtext: Adapterring for RT 49.5" NATIONAL P/N 55320 SERIAL-NO: XXX B+V XX/XX API 7K - 0039 PSL /SR weight: 2200 kg 0 2 w Rz 00 x Rz 25 y Rz 6 z Rz 6,3 3 4 5 2 4 Stck 7626 threaded pindin 94 M2x20-2 Stck 6258 Protection Cap - 0 2 Stck 70064 Grease nipple G/8" - 9 4 Stck 63825 Safety Sheet DIN 463-3 - 8 4 Stck 6558 ScrewDIN 933-M2x30-7 2 Stck 55323 Securing Plate - 6 4 Stck 7556 Lifting eye Thiele M20, 2000 kg - 5 8 Stck 75568 Securing Ring DIN 472-28x,2-4 8 Stck 725465 DIN 92 M6x90-3 2 Stck 553202 Adapter Plate 2x 4,5 kg 2 2 Stck 55322 Hinge Pin 2x 2 kg 2 Stck 5532 Hinged Adapter 2x 062 kg Pos Mge Eht Partnr. Bezeichnung Bemerkung The present document is the property of BLOHM & VOSS Repair GmbH This document or any part there of must neither be used, reproducted, communicated, published, nor made known third parties in any other way, unless the corresponding authorisation has been previously obtained from Blohm & Voss writing. 8 - - - 7 - - - 6 - - - 5 - - - 4 - - - 3 - - - 2 - - - Stückliste geändert 23.08.05 ST ch.no engineering change day name Tolerance DIN ISO Surface DIN ISO 2768-m 302 day name drawn 2.05.04 M.M. check. 2.05.04 J.G. norm BLOHM & VOSS Repair GmbH Oil Tool Division Hamburg-Germany AUTHORIZED MANUFACTURER Scale : Weight 2200kg Werkstoff part name Adapterring for RT 49.5" National, Assembly part no. sheet 55320 sh. h:\prtakt\ - 6
5. ADDRESS LIST Blohm + Voss Oil Tools Hermann-Blohm-Straße 2 20457 Hamburg Germany Phone: +49 40/39-826/62 Fax: +49 40/39-894 oiltools@blohmvoss.com www.blohmvoss-oiltools.com Blohm + Voss Oil Tools, LLC 7670 Woodway, Suite 266 Houston, Texas 77063 United States of America Phone: +-73-952 0266 Fax: +-73-952 2807 bvot@blohmvoss.com www.blohmvoss-oiltools.com Premier Sea & Land Pte. Ltd., Scotts Road #9-2 Shaw Centre Singapore 228208 Republic of Singapore Phone: +65-6734-777 Fax: +65-6734-95 enquiries@mtqpremier.com.sg 7