Technical Specifications Integra / Summer Breeze 2007-8 Domestic Ducted Evaporative Air Conditioners Integra VSS55, VSM65, VSL75
Introduction TECHNICAL SPECIFICATIONS Page 2
Table of Contents WARRANTY... 4 PRODUCT RANGE... 6 Integra Units... 6 Summer Breeze Units... 7 PRODUCT SPECIFICATIONS... 8 Unit Construction... 8 Product Weight & Dimensions... 8 Fan Specification... 8 Fan Motors... 8 Pumps... 9 Evaporative Pads... 9 Water Management... 9 Electrical Systems... 9 PRODUCT DIMENSIONS... 10 WIRING DIAGRAM... 11 TECHNICAL SPECIFICATIONS Page 3
Warranty (Australia Only) Warranty IMPORTANT: Please read this warranty information and complete the Dealer/Product information on the following page. KEEP this with your original purchase documents for any claim under warranty. WARRANTY PROCEDURES: Firstly refer to your owners manual to ensure you have followed the correct operating procedures of your product, and refer to the trouble shooting guide to assist solving any problems you may have. 1. Read this warranty statement carefully before you request warranty service as items relation to installation are not covered by this appliance warranty. 2. A proof of product purchase must be provided for warranty service, to validate the appliance is within the manufacturer s warranty periods. 3. This warranty is only for products and associated original controls for Climate Technologies manufactured product. 4. Only an authorised Climate Technologies service provider must carry out warranty service. Climate Technologies provides the following Manufacturers warranty additional to all implied warranties and other statutory rights which you may have under the Trade Practices Act and similar State & Territory Laws, subject to the following terms and conditions. TERMS AND CONDITIONS: Conditions to warranty Subject to the exclusions noted, Climate Technologies warrant the product for the period as prescribed in the table following this statement to be free from Inherent defects in materials and workmanship for functional and structural components. This product is only valid if the product is operated in accordance with the manufacturers instructions The appliance must not be modified or changed in any way. Your proof of purchase MUST be produced before free service will be provided. Traveling time and mileage are included within 30km of either your authorised Climate Technologies dealer or service provider s premises. Customers in areas other than the above are responsible for any traveling time and mileage required to carry out warranty repairs. The product must be installed by a qualified person in the manner prescribed by local & statutory regulations and to the manufacturer s specifications. Service within the terms of this warranty will be recognised where we are satisfied that the appliance or part was supplied within the relevant time limits. Documents of purchase and Dealer/Installer information will assist in this process. Product fitness for purpose and overall system design / sizing is solely the responsibility of the dealer / installer. This includes but is not limited to heat load calculations, air flow, system balancing, humidity, water quality etc. The product must be installed in an easily and safe accessible area for service, appliances installed in areas not easily and safely assessable, costs will be borne by the owner for access equipment should maintenance be required. DIY installation Warranty If the product has been installed as a DIY, a supply part only warranty will apply. Parts only will be supplied free of charge on the return of the faulty part and the owner will be responsible for all labour charges incurred for the part to be fitted by a qualified person. Labour warranty as prescribed in the following table is void in this situation. Remote Location Warranty If the product has been installed outside the Climate Technologies service network, a supply part only warranty will apply. Parts only will be supplied free of charge on the return of the faulty part and the owner will be responsible for all labour charges incurred for the part to be fitted by a qualified person. Labour warranty as prescribed in the following table is void in this situation. TECHNICAL SPECIFICATIONS Page 4
Warranty (Australia Only) EXCLUSIONS TO WARRANTY. Consumable items subject to wear and tear such as filter pads, drive belts and bearings are not covered by this warranty. Components used as part of the installation such as grilles filters, ducting, fittings, zone motors and consumer services pipe work are warranted from your place of purchase and not covered by this warranty. Damage caused by elements such as wind, rain, lighting, floods etc along with power spiking and brownouts are not considered defective material or workmanship and as such are not considered warranty. No responsibility will be accepted for outside elements such as pests, animals, pets and vermin that may cause damage to the unit. Harsh environmental situations such as salt air that may cause cabinet damage / rusting can not be considered warranty. The manufacturer does not accept liability or any claims for damage to building contents, carpet, walls, ceilings, foundations or any other consequential loss either direct or indirect. Damage resulting from, power spikes, incorrect operation, incorrect installation, and incorrect maintenance is also not covered. All warranties are NOT transferable. Conditions where warranty may be void. If there is no certificate of compliance for plumbing, electrical or refrigeration as required by State & Territory Laws. Climate Technologies reserves the right to refuse service on non-compliant installations. The defective operation of the appliance that is due to failure of electricity, gas, water or refrigerant gas supplied. Defects are caused by neglect, incorrect application, abuse or by accidental damage of the appliance. An unauthorised person has attempting to repair the appliance. A situation arises referenced in the trouble-shooting guide. A charge will be made for work done or a service call where there is nothing wrong with the appliance. WARRANTY PERIODS Unit Components RESIDENTIAL COMMERCIAL Parts Labour Parts Labour Corrosion on Cabinet 25 3 2 2 Structural Guarantee 10 3 2 2 ** All other components 3 3 1 1 ** Filter pads are a consumable item and therefore are not covered by the above warranty periods. TECHNICAL SPECIFICATIONS Page 5
Product Range Product Range Integra Units Part Number Model 6060032GYE 6060032RDE 6060032BEE 6060032GNE 6060032CHE VSS55 Grey W/Seal DV VSS55 Red W/Seal DV VSS55 Beige W/Seal DV VSS55 Green W/Seal DV VSS55 Chocolate W/Seal DV 6060036GYE 6060036RDE 6060036BEE 6060036GNE 6060036CHE VSS65 Grey W/Seal DV VSS65 Red W/Seal DV VSS65 Beige W/Seal DV VSS65 Green W/Seal DV VSS65 Chocolate W/Seal DV 6060038GYE 6060038RDE 6060038BEE 6060038GNE 6060038CHE VSS75 Grey W/Seal DV VSS75 Red W/Seal DV VSS75 Beige W/Seal DV VSS75 Green W/Seal DV VSS75 Chocolate W/Seal DV Accessories 5000005 RF Remote Control 6050064 Touchpad 5001915 Comms Cable Only 5011915 10m Extension Cable 5001675 Antenna TECHNICAL SPECIFICATIONS Page 6
Product Range Summer Breeze Units Part Number Model 6060032GY 6060032RD 6060032BE 6060032GN 6060032CH VSS55 Grey DV VSS55 Red DV VSS55 Beige DV VSS55 Green DV VSS55 Chocolate DV 6060036GY 6060036RD 6060036BE 6060036GN 6060036CH VSS65 Grey DV VSS65 Red DV VSS65 Beige DV VSS65 Green DV VSS65 Chocolate DV 6060038GY 6060038RD 6060038BE 6060038GN 6060038CH VSS75 Grey DV VSS75 Red DV VSS75 Beige DV VSS75 Green DV VSS75 Chocolate DV Accessories 5000006 LV Programmable 5000006 LV Manual Summer Breeze 5001915 Comms Cable Only 5011915 10m Extension Cable 6001343 Enviroseal 550 x 550 6021344 Enviroseal 800 x 550 TECHNICAL SPECIFICATIONS Page 7
Product Specifications INTEGRA / SUMMER BREEZE 2007/8 Product Specifications Description Unit Construction Cabinet Base Venturi Screws Motor Mounting arms Product Weight & Dimensions Integra VSS50 VSS55 VSM60 VSM65 VSL70 VSL75 Injection Moulded Polypropylene Injection Moulded Polypropylene Injection Moulded Polypropylene Stainless Steel Pressed Metal - Powder Coated Shipping Weight 61 65 80 Operating Weight 84 92 109 Weight excluding fan and louvres 29.5 30 31.5 Cabinet Dimension 1184 Sq 1192 Sq 1192 Sq Cabinet Height Front 683 790 1047 Cabinet Height Back 573 681 937 Duct Discharge Sizes 558 x 558 558 x 808 Dropper Duct Requirement 550 x 550 550 x 800 Fan Specification Fan Type V16 (5 Blade Axial) V16 (10 Blade Axial) ***** Sound Pressure Levels - 1 metre Db(A) 64.5 66 66.5 68 65.5 66.5 Fan Diameter 493mm Fan Pitch 28.0 o 31.0 o 37.0 o Hub Fastening Fan Motors Type Taperlock Variable Speed Motor Description 855BPVA-A11 855BQVA-A16 855-BRVA-B13 Watts In (@ Maximum Rated Load) 970 1040 1540 Watts Out 600 750 950 Volts / Phase / Hz 240/1/50 Current - High Speed Amps @ 80pa 1.6 1.9 3.0 3.1 4.5 4.8 RPM - High Speed 1260 1410 1360 1400 1190 1350 RPM - Low Speed (Minimum set) 500 500 500 500 500 500 Overload Protection Shaft Diameter Bearings Internal Auto Reset Thermal Overload I /2" (12.7mm) Sealed Ball Capacitor 15μƒ 25μƒ 25μƒ Capacitor Rating P2 P2 P2 TECHNICAL SPECIFICATIONS Page 8
Product Specifications SPECIFICATIONS Description Pumps Type Shaft Body Motor Wiring Specifications Motor Overload Protection Bearings Strainer Material Flow Rate L/M Watts In Watts Out Current RPM (Nominal) Integra VSS50 VSS55 VSM60 VSM65 VSL70 VSL75 JRM E/P38 Stainless Steel ABS Plastic Encapsulated Shaded Pole Thermal Overload / Auto Reset D.F. Ball Polypropylene Variable to 24 litres per minute x 1.2 Metre high 50w 40w 0.35 amp 2300 rpm Volts / Phase / Hz 240/1/50 Evaporative Pads Type Celdek 5090 (45 o x 45 o ) Size 755 x 365 755 x 480 755 x 736 Thickness 90 mm Open Area Total 1.01 M² 1.35 M² 2.09 M² Air Velocity (High) 1.4m/s 1.7m/s 1.5m/s 1.7M/s 1.2m/s 1.3m/s Water Management Float Valve Float Valve - Water Pressure Range 1/2" BSP Cistern Float Valve 100-500 kpa Tank Capacity - Litres 17.5 Over flow fitting Dump Valve Dump Mechanism - Min. / Max. Dump Valve Solenoid Electrical Systems RF Remote Control LV Programmable LV Touchpad LV Manual 50mm combination drain & overflow 40mm or 19mm 100 to 500 Kpa 100-500 Kpa Continuous Rating 240V 50Hz 10amp variable speed controlled 240V 50Hz 10amp variable speed controlled 240V 50Hz 10amp variable speed controlled 240V 50Hz 10amp variable speed controlled ***** Dba ratings are internal tests measured at 1 metre radial from the unit tested in semi reverberant room. Units currently under independent NATA laboratory testing. TECHNICAL SPECIFICATIONS Page 9
PRODUCT DIMENSIONS INTEGRA / SUMMER BREEZE 2007/8 Product Dimensions Model A B C D E F G H VSS 55 573 683 1184 1184 560 560 VSM 65 681 790 1192 1192 560 660 VSL 75 937 1047 1192 1192 560 810 TECHNICAL SPECIFICATIONS Page 10
Wiring Diagram INTEGRA / SUMMER BREEZE 2007/8 Wiring Diagram TECHNICAL SPECIFICATIONS Page 11
Issue B September 2007