Door Height Door width ±2 mm The closing speed of the soft closing type door may change due to Meaning of symbols Warning Caution Prohibited Required 1
2 Name Recessed roller soft closer Recessed roller Upper track Upper track Spanner Item Accessories Nut Countersunk head tapping screw 2 pcs Countersunk head tapping screw Remarks Attached to either one Hole pitch Pitch end Attached to Name Cover cap Door stopper Door guide track Upper track cleaner Upper track for standard sliding Upper track for standard sliding Item Accessories Thickness: 2 mm Remarks Hole pitch Pitch end either one Hole pitch Pitch end Recommended screw: Countersunk Track Track (Recessed) (Surface mounted) 21 +4-3 (Vertical adjustment) 9 20 1 523.5[525.5] 2 187.5 φ4.4 φ7.8 CSK 5 2 3 2 φ4.5 (additional) [Door width - 363] 2 4 44 16 48 49 3 51 17-0.5 0 11 20 22 9 +4-3 (Vertical adjustment) See " when door stopper 12 15 18 28 10 2 [ ] : When cover cap (option) is used. 2 15 4 12 4 Cover cap (option) Door guide track (option) 15
See " Door width - 376 [Door width - 378 ] 2 Cut end Trailing edge Sticker 2 φ4.5 (for trigger fixing) φ4.5 φ7.8 CSK (for track fixing) Leading edge 2 [ ]: When Cover cap (option) is used. Pull out casing Main unit Pull up lever Casing Correct set position catcher (Red colored part) Correct set position φ6 catcher (Red colored part) Incorrect set position
Insert the parts in order from to Remove any dirt or aluminum chips from 1 Two-way soft closer 2 Recessed roller Tape recessed roller and upper track to prevent Upper track Cut end Trailing edge Tape Sticker Install as shown. Leading edge Upper track Tape Leading edge OK inclined loosen overtightened deeper groove Align trigger with Out of straight 90 90 OK Correct installation 2 φ4.5 Screws Out of straight assembly Jig Screwdriver (+) OK Correct installation
Position the floor guide so that the roller part stays Temporarily fasten through the elongated holes with the provided Leading edge Trailing edge Fully closed Elongated hole Elongated hole Floor guide Fully opened 4 16 4 Insert the recessed roller into the casing until a CLICK Casing Support Mark Lever Floor guide Lever main unit Lever Mark Confirm that the recessed roller is not Close the door slowly and check that the soft closer (crimping) Please refer to the Troubleshooting section when the
9 3 mm 4 mm Vertical position adjust screw Floor guide Forward/backward adjustment screw 613 2 mm 2 mm Jump prevention nut Tighten 6
Then pull out the recessed roller main unit from the door while Spanner Lever door stopper and bumper block on Min.13 Bumper block (Option) Min.13 Bumper block (Option) damaged if door stopper and Door stopper (Option) Door stopper (Option) [Door width - 363] 2 187.5 187.5 2 φ4.5 2 φ4.5 2 φ4.5 2 φ4.5 [Door width - 363] 2 This is where the doors meet. Bumper block 2 [ ] : When cover cap (option) is used. 7
Reference line for leading edge. (Leading edge when the door is stopped.) Standard installation Upper track installed inside a door jamb 187.5 Crimped trigger 361 [363] 2 [Door width - 363] 2 Reference line for trailing edge. (Trailing edge when the door is opened.) Available opening width Door width Other installation Ex. Without vertical frame Door stops here when closed. Bumper block Door must be stopped by bumper block and door stopper. Leading edge at full open 187.5 Available opening width 361 [363] 2 [Door width - 363] 2 Door width Door stops here when opened. Bumper block Door must be stopped by bumper block and door stopper. Door stopper Door stopper 2 [ ] : When cover cap (option) is used. Trouble Checkpoint Solution Door stops during soft closing No soft closing Abnormal noise during operation The position of the trigger catcher may become dislocated (See section Repeat this action on the opposite side Heavy door operation SUGATSUNE KOGYO CO.,LTD Tokyo, JAPAN Phone: +81 (0)3 3866 2260E-mail:export@sugatsune.co.jp SUGATSUNE KOGYO (UK) LTD Reading, UK Phone: +44 118 9272 955 E-mail:sales@sugatsune.co.uk SUGATSUNE EUROPE GmbH Dusseldorf, GERMANY Phone: +49 211 53812900 E-mail:sales@sugatsune.eu 8 SUGATSUNE SHANGHAI Co., LTD Shanghai, CHINA Phone: +86 21 3632 1858 E-mail:lamp@sugatsune.com.cn Guangzhou, CHINA Phone: +86 20 6639 3552 E-mail:lamp@sugatsune.com.cn SUGATSUNE AMERICA, INC California, USA Phone: +1 310 329 6373E-mail:sales@sugatsune.com Chicago, USA Phone: +1 312 461 1081 E-mail:chicagoshowroom@sugatsune.com. SUGATSUNE KOGYO INDIA PRIVATE LIMITED SUGATSUNE CANADA, INC. Mumbai, INDIA Phone: +1 514 312 5267 E-mail:support@sugatsune.ca Phone: +91 22 28314490/91E-mail:sales@sugatsune.in 2018.100963-2