INSTALL GUIDE DOCUMENT NUMBER 0 REVISION DATE FIRMWARE OEM-GM(RS)-GM-[ADS-GM] HARDWARE ADS-GM ACCESSORIES ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
PAGE OF 0 DOC.: #0 VEHICLE LIST - OF Malibu STD key AT (with PK) 0- Malibu Hybrid STD key AT (with PK) 0- Malibu MAXX STD key AT (with PK) 0-0 G STD key AT 0-0 Pursuit / G STD key AT (with PK) 0-0 Solstice STD key AT (with PK) 0-0 Aura / Hybrid STD key AT (with PK) 0-0 Sky STD key AT (with PK) 0-0 RAP SHUTDOWN CTRL BRAKE PEDAL STATUS OUTPUT PRIORITY UNLOCK* IGNITION CTRL DOOR UNLOCK* PARKING LIGHT CTRL DOOR LOCK* TACHOMETER OUTPUT DISARM OEM ALARM TRUNK STATUS OUTPUT ARM OEM ALARM DOOR STATUS OUTPUT X LOCK START/STANDALONE MOD. 0- PUDDLE LIGHT CTRL** DATA IMMOBILIZER BYPASS 0-0 HHR STD key AT (with PK) TRUNK/HATCH RELEASE* YEAR Cobalt STD key AT (with PK) INSTALL TYPE MODEL SATURN PONTIAC CHEVROLET MAKE FEATURES *Doorlocks and trunk release features on the module will not operate on vehicles that are not equipped with OEM keyless entry. **If puddle light function is active in vehicle settings. Automotive Data Solutions Inc.
PAGE OF 0 DOC.: #0 BOX CONTENTS - OF BOX CONTENTS MODULE 0 PIN T-HARNESS VS MS LED BLUE BLACK BLACK 0 0 0 PROGRAMMING BUTTON LED A G F B JS VS MS E BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK T-HARNESS PIN VS JS AFTERMARKET HOOD SWITCH AND CABLE VS C D 0 WHITE T-HARNESS VS WARNING STICKER JS VS PIN JS WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc.
PAGE OF 0 DOC.: #0 SATURN PONTIAC G STD key AT (with PK) Aura / Hybrid STD key AT (with PK) Automotive Data Solutions Inc. MODULE LOCATION COMPONENT LOCATOR 0-0 Trunk Driver Door Pin POLARITY Parking Light WIRE COLOR Malibu MAXX STD key AT (with PK) 0- Horn POSITION Malibu Hybrid STD key AT (with PK) Doorlock TYPE Brake 0- Keyless Data COLOR Malibu STD key AT (with PK) NAME YEAR WIRE DESCRIPTION MODEL CHEVROLET MAKE TYPE - WIRE CHART - OF (MUX) Tan 0 Brown/ Brown/ /Black Brake Keyless Data Doorlock (MUX) Tan Parking Light 0 Brown/ Trunk Brown/ Driver Door Pin /Black Brake Keyless Data Doorlock (MUX) Tan Parking Light 0 Brown/ Trunk Brown/ Driver Door Pin /Black 0-0 Horn 0-0 Horn
PAGE OF 0 DOC.: #0 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITION SWITCH A VS A G RF PORT/WEBLINK PORT B F TELEMATIC PORT IGNITION E C A VS D IGNITION HARNESS A B VS MS -WAY PK JS JS JS B VS B -WAY PK HARNESS 0 0 MS B B A A C WHITE - KEYLESS DATA OUTPUT 0 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT 00 TO 00 MODELS WITH OEM KEYLESS ONLY OPTIONAL PARKING LIGHT - 0 HORN - 0 0 0 0 0 GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN - UNLOCK OUTPUT WITHOUT OEM KEYLESS ONLY TRUNK RELEASE - DOORLOCK (MUX) - 0 0 0 PURPLE/GREEN - LOCK OUTPUT 0 BLUE/GREEN - TRUNK OUTPUT D 0 KEYLESS DATA - 0 GRAY/BLACK - BRAKE (+) INPUT 0 GRAY/WHITE - HOOD STATUS INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH 0 0 0 0 0 0 00 OHM 00 TO 00 MODELS ONLY DRIVER DOOR PIN - BRAKE (+) - 0 AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc.
PAGE OF 0 DOC.: #0 SATURN PONTIAC Pursuit/G STD key AT (with PK) Sky STD key AT (with PK) Automotive Data Solutions Inc. NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR YEAR MODEL Cobalt STD key AT (with PK) WIRE DESCRIPTION CHEVROLET MAKE TYPE - WIRE CHART - OF Brake Keyless Data Doorlock 0 (MUX) Tan Parking Light 0 Brown/ Trunk 0 Tan Driver Door Pin /Black 0-0 Horn Brake Keyless Data Doorlock 0 (MUX) Tan Parking Light 0 Brown/ Trunk 0 Tan Driver Door Pin /Black Brake Keyless Data Doorlock 0 (MUX) Tan Parking Light 0 Brown/ Trunk 0 Tan Driver Door Pin /Black 0-0 Horn 0-0 Horn
PAGE OF 0 DOC.: #0 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITION SWITCH A VS A G RF PORT/WEBLINK PORT B F TELEMATIC PORT IGNITION E C A VS D IGNITION HARNESS A B VS MS -WAY PK JS JS JS B VS B -WAY PK HARNESS 0 0 MS B B A A C WHITE - KEYLESS DATA OUTPUT 0 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT 00 TO 00 MODELS WITH OEM KEYLESS ONLY OPTIONAL 00 TO 00 MODELS ONLY 0 PURPLE/GREEN - LOCK OUTPUT 0 BLUE/GREEN - TRUNK OUTPUT KEYLESS DATA - PARKING LIGHT - 0 HORN - 0 0 0 GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN - UNLOCK OUTPUT TRUNK RELEASE - 0 DOORLOCK (MUX) - 0 0 0 00 OHM 0 0 0 0 BRAKE (+) - WITHOUT OEM KEYLESS ONLY D 0 0 0 0 GRAY/BLACK - BRAKE (+) INPUT 0 GRAY/WHITE - HOOD STATUS INPUT 0 0 DRIVER DOOR PIN - 0 WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc.
PAGE OF 0 DOC.: #0 Automotive Data Solutions Inc. NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR YEAR MODEL HHR STD key AT (with PK) WIRE DESCRIPTION CHEVROLET MAKE TYPE - WIRE CHART - OF Brake Keyless Data Doorlock 0 or /Black (MUX) Tan Parking Light 0 Brown/ Trunk /Black Driver Door Pin /Black 0- Horn
PAGE OF 0 DOC.: #0 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITION SWITCH A VS A G RF PORT/WEBLINK PORT B F TELEMATIC PORT IGNITION E C A VS D IGNITION HARNESS A B VS MS -WAY PK JS JS JS B VS B -WAY PK HARNESS 0 0 MS B B A A C WHITE - KEYLESS DATA OUTPUT 0 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT 00 TO 00 MODELS WITH OEM KEYLESS ONLY OPTIONAL 00 TO 00 MODELS ONLY 0 PURPLE/GREEN - LOCK OUTPUT 0 BLUE/GREEN - TRUNK OUTPUT KEYLESS DATA - PARKING LIGHT - 0 HORN - 0 0 0 WITHOUT OEM KEYLESS ONLY TRUNK RELEASE - DOORLOCK (MUX) - 0 0 0 0 0 BRAKE (+) - GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN - UNLOCK OUTPUT D 0 0 GRAY/BLACK - BRAKE (+) INPUT 0 GRAY/WHITE - HOOD STATUS INPUT 0 0 0 0 0 0 00 OHM DRIVER DOOR PIN - 0 WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc.
PAGE 0 OF 0 DOC.: #0 Automotive Data Solutions Inc. NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR YEAR MODEL Solstice STD key AT (with PK) WIRE DESCRIPTION PONTIAC MAKE TYPE - WIRE CHART - OF Brake Keyless Data Doorlock 0 (MUX) Tan Parking Light 0 Brown/ Trunk 0 Tan Driver Door Pin /Black 0-0 Horn
PAGE OF 0 DOC.: #0 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITION SWITCH A VS A G RF PORT/WEBLINK PORT B F TELEMATIC PORT IGNITION E C A VS D IGNITION HARNESS A B VS MS -WAY PK JS JS JS B VS B -WAY PK HARNESS 0 0 MS B B A A C WHITE - KEYLESS DATA OUTPUT 0 00 TO 00 MODELS WITH OEM KEYLESS ONLY BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT OPTIONAL KEYLESS DATA - PARKING LIGHT - 0 HORN - 0 0 0 WITHOUT OEM KEYLESS ONLY GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN - UNLOCK OUTPUT TRUNK RELEASE - 0 DOORLOCK (MUX) - 0 00 OHM 0 GRAY/BLACK - BRAKE (+) INPUT 0 GRAY/WHITE - HOOD STATUS INPUT 0 0 0 0 0 PURPLE/GREEN - LOCK OUTPUT 0 BLUE/GREEN - TRUNK OUTPUT D 0 0 0 00 TO 00 MODELS ONLY BRAKE (+) - DRIVER DOOR PIN - 0 0 0 0 0 WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc.
MODULE PROGRAMMING PROCEDURE - OF Close driver door. 0 ACC ON START 0 Re-open driver door to wake up data bus. 0 0 Insert key into ignition. Wait seconds. 0 ACC START 0 Turn key to ACC position. Wait seconds. ACC ON Turn key to position. ACC ON START Module Programming Procedure completed. START 0 0 Release key from Start position and return to ON position. Wait, LED will turn solid GREEN for seconds. ON PAGE OF 0 DOC.: #0 Turn key to ON position. Wait seconds. ACC ON START 0 ACC ON START Turn key to START position and hold for seconds. Automotive Data Solutions Inc.
VALET MODE PROGRAMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Time restriction. Complete next step within seconds. 0 ACC ON START >> PAGE OF 0 DOC.: #0 To exit valet mode: repeat steps to. Cycle ignition ON five times [x /ON] rapidly. ENGINE START STOP 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. ACC ON START ENGINE START STOP 0 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc.
PAGE OF 0 DOC.: #0 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to position. 0 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 0 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 0 ACC ON START TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 0 [X] Automotive Data Solutions Inc.
PAGE OF 0 DOC.: #0 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 0 DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS 0 TAKEOVER 0 0 [Z] SETTINGS MODULE NAVIGATION CHART - OF FACTORY KEYLESS RS SEQUENCE CONFIGURATION 0 0 MODULE RUN TIME WAIT TO START DELAY 0 ON 0 ON 0 ON 0 ON ENABLE 0 DISABLE* DISABLE 0 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN 0 MIN 0 MIN 0 SEC 0 0 SEC 0 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0 *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc.
PAGE OF 0 DOC.: #0 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES [Z] SETTINGS MODULE NAVIGATION CHART - OF HORN EVENT TRIGGER CONFIGURATION 0-0 Technical Support only HORN CHIRPS WIDTH DOUBLE LOCK 0 LOCK + UNLOCK 0 LOCK + UNLOCK + START 0 DOUBLE LOCK + START 0 msec 0 msec 0 0 msec *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc.
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is ON. 0 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 0 Glow plug timeout error. 0 RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. 0 CAN communication failure during RS sequence. REMOTE STARTER ERROR CODES: NOTES Automotive Data Solutions Inc. PAGE OF 0 DOC.: #0
I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION Automotive Data Solutions Inc. DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE OF 0 DOC.: #0
MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the BLACK 0-PIN connector. 0 Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. 0 Repeat programming procedure. 0 PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Automotive Data Solutions Inc. PAGE OF 0 DOC.: #0
INSTALLATION CHECKLIST - OF PAGE 0 OF 0 DOC.: #0 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. Exit vehicle. Installation checklist completed. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Automotive Data Solutions Inc.