TRx Heavy-Duty Swing Away Legrests Installation and Set-Up Manual i NOTE: This installation manual contains important information related to set-up and adjustments. Please forward to the Dealer, together with the TRx system, in order to properly address the specific needs of the client.
- 2 - Important The most important link in the delivery chain is the end user. The user must be satisfied with the product in terms of function, safety and aesthetics. No sale is complete unless the end user receives thorough training in all aspects of the care and use of the system. A complete instruction session with your customer is essential. Only the dealer and the health care professional can ensure that the system is set up properly and safely for the specific needs of the individual user. Training Installation and set-up of the Heavy Duty Swing Away Legrests must only be done by a trained technician or healthcare professional. If you are not certified as an installer, please arrange immediately for training by a Motion Concepts technician or sales agent who has been certified to teach installation and set-up of the Swing Away Legrests. Every effort will be made to meet your training needs. Note: Before proceeding with the installation/ set-up, please ensure that no pages are missing from this manual. Tools The following tools are required for the installation/ set-up of the pivot plus power legrests: Wrenches: 7/16, 1/2 Socket wrenches: 7/16, 1/2 Allen keys: 3/16, 1/4, 1/8 Screw Drivers
- 3 - Table of Contents 1.0 Adjustment Overview Drawing: Figure 1.0: TRx Heavy-Duty Swing Away Legrests 2.0 Legrest Set-Up and Adjustments 2.1 Installing the TRx Heavy-Duty Swing Away Legrests 2.2 Adjusting the Mounting Pin 2.3 Leg Extension Adjustments 2.4 Footplate Adjustments
- 4-1.0 Adjustment Overview Drawing Figure 1.0- TRx Heavy Duty Swing Away y Legrest est Pin Adjustment Bolt Note: Extension Bar not shown Plunger Pin Plunger Assembly Adjustable Heel Strap nylon set-screw (to adjust foot plate angle) Mounting Pin Clamping Block main tube assembly extension tube adjustments at 1/2 intervals. extension bar 3 sizes available: S- 12-16 L- 15-19 XL- 18-21 pivot bracket assembly
2.0 Legrest Set-Up & Adjustments 2.1 Installing the TRx HD Swing Away y Legrest est - 5 - Note: Set-up and adjustments on the HD Swing Away Legrests will need to be addressed individually for both the left and right legrests. 1. Insert the mounting pin into the legrest receiver and lock the plunger into position (see image A below). Refer to image F. (p.6) to see an example of an improperly locked plunger. 2. When the legrest is properly inserted into the legrest hanger, the beveled shoulder of the hanger will align with the beveled shoulder on the foot-rest assembly (see image C. below). 3. Test the fit of the legrest assembly by moving it laterally and from front to back. There should be no play after the legrest is in the locked position. If there is any play evident in the locked legrest, the eccentric mounting pin may be adjusted to compensate. To adjust the mounting pin please refer to Section 2.2 Adjusting the Mounting Pin (p.6). A. B. plunger in locked position test for play in the legrest. (ensure plunger is locked) unlock legrest hanger Overhead View C. beveled shoulder eccentric mounting pin
2.0 Legrest Set-Up & Adjustments - 6-2.2 Adjusting the Mounting Pin Note: the threaded extrusion at the top of the mounting pin is designed to be slightly off-center. This unique design causes the pin to rotate in an elliptical (non-circular) path. Therefore, as the pin is tightened it will create a wedge affect and force the legrest to snug up against the legrest receiver. D. top Mounting Pin bottom (view from top) To ensure a tight fit between the legrest and the reciever, the mounting pin can be adjusted as follows (refer to image E.): 1. With the plunger pin still engaged, use an allen key to loosen the pin adjustment bolt. 2. Use a wrench to rotate the mounting pin inside the legrest receiver until a snug fit is achieved. 3. With the wrench holding the mounting pin in position, re-tighten the adjustment bolt with the allen key. 4. Important!- Test the plunger assembly to ensure it is functioning/ locking properly (see image F.). If the plunger mechanism is too stiff or the plunger pin does not lock fully, loosen the mounting pin slightly and re-test. E. F. plunger mechanism not locked properly gap
- 7-2.0 Legrest Set-Up & Adjustments 2.3 Leg g Extension Adjustments 1. The leg extension is adjustable to accommodate various knee to heel lengths. There are three lengths of extension bars available: Small = 12-16 Large = 15-19 X-Large = 18-21 (Note: extension bars are adjustable at 1/2 intervals) 2. To adjust the leg extension, remove the two screws from the down tube and re-position the extension bar. Align the holes in the down tube with the holes in the extension bar and re-fasten the screws in the new position. G. legrest down tube adjustment screws legrest extension bar 2.4 FootplaF ootplate te Adjustments The footplate can be adjusted in several locations, depending on the client's needs. Please refer to Figure 2.0 and additional images (p.8) for an illustration of the various footplate adjustments. Figure 2.0- Footplate Adjustment Overview adjustable heel strap Note: Extension Bar not shown nylon set-screw (to adjust foot plate angle) pivot bracket clamping block (Note: clamp can also be inverted to allow 3 additional adjustments) Bottom View
- 8-2.0 Legrest Set-Up & Adjustments 2.4 FootplaF ootplate te Adjustments (...cont d) 1. The clamping block can be fastened to the footplate in 3 different locations. These adjustments will move the entire footplate position forward and aft. Note: by inverting the clamping block, 3 additional forward and aft mounting positions can be achieved. Each adjustment is at a 1 interval 2. By loosening the clamping block, the entire footplate can be move in and out along the length of the pivot bracket tube. (see image H.) 3. The heel strap can also be adjusted into 3 different positions (front to back). Each strap adjustment is at a 1 interval. 4. The angle of the footplate can be altered by adjusting the nylon set-screw inside the pivot bracket. With the set screw fully inserted the footplate will rest at 90 degrees (perpendicular to the legrest extension tube). Loosening the set screw will gradually decrease the footplate angle (less than 90 degrees). (see images I. & J.) H. clamping block J. pivot bracket tube extension bar nylon set screw I. adjustable footplate angle USA 700 Ensminger Rd. Suite 112 Tonawanda, NY, USA 14150 716-447-0050 888-433-6818 Canada 84 Citation Dr. Units 1-3 Concord, Ontario, Canada L4K 1C9 905-695-0134 www.motionconcepts.com