REMOTE GREASE ASSEMBLY FOR PARALLEL LIFT PLOW

REMOTE GREASE ASSEMBLY FOR PARALLEL LIFT PLOW HENKE MODEL: REMOTE GREASE ASSEMBLY PARTS AND INSTALLATION MANUAL: # 86382190-01 VERSION 010, DECEMBER 2018 MY SERIAL NUMBER: HENKE MANUFACTURING CORPORATION MANUFACTURERS OF SNOW REMOVAL EQUIPMENT FOR OVER 100 YEARS 3070 WILSON AVE.LEAVENWORTH, KS 66048 Phone:(913) 682-9000Fax: (913) 682-0300 www.henkemfg.com, parts@henkemfg.com PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010

<<THIS PAGE IS INTENTIONALLY LEFT BLANK>> PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 2 of 28

Introduction Thank you for your purchase of a HENKE Remote Grease Assembly For Parallel Lift Plow (Remote Grease Assembly). This Parts and Installation Manual should be read in its entirety, including the safety section, before installation, operation, or maintenance is performed to minimize installation and operation problems. In addition to their field-proven standard units, Henke designs and manufactures snow fighting equipment to meet specific customer requirements. The field hardware required to install your new Henke product is listed in tables in the parts section of this book. Be sure to check that all parts listed in this document were shipped with your Plow (either attached or loose). In the unlikely situation that parts are missing please contact Henke Manufacturing at (913) 682-9000 or service@henkemfg.com before continuing the installation. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 3 of 28

Contact Your Local Dealer For Parts & Service Henke's Dealer Network is a key component in providing our customers with the quickest most efficient access to Henke's Parts and Technical Service teams. For Parts Replacement, Technical Service, & Customer Support Inquiries, please contact your local Henke dealer first. Find your dealer using our website Dealer Locator: http://henkemfg.com/dealer-locator/ If you do not have a local dealer, contact Henke directly, as listed below. Replacement Parts Henke's Parts team will assist in parts replacement and preventative parts stocking program. Dealers and individual owners without a local dealer can contact us via email, website, or phone. parts@henkemfg.com http://henkemfg.com/parts-and-service/ 888 682-9010 x3 This will direct your inquiry to the entire Parts team, insuring the most prompt attention possible. All inquiries are processed in the order they are received. NOTE: We can prepare a personalized wear parts recommendation and optionally include your seasonal purchasing summary. Just ask. Call Henke's Technical Service team in the unlikely event that your order is missing parts. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 4 of 28

Technical Service & Customer Support Inquiries Henke Technical Service can assist in optimizing your Henke equipment, and increasing up-time by providing technical guidance and support for issues as they occur. Dealers and individual owners without a local dealer can contact us via email, website, or phone. service@henkemfg.com http://henkemfg.com/parts-and-service/ 888 682-9010 x6 This will direct your inquiry to the entire Tech Service team, insuring the most prompt attention possible. All inquiries are processed in the order they are received. We truly appreciate your business. Henke Parts and Technical Service Teams Is This Your Product Manual? We strongly recommend verifying your product s serial number and product manual number and revision with Henke s Parts Department before you order parts. Henke prides itself on service and support of all of our products including current, legacy, custom, and standard designs. Therefore, many of Henke products appear similar, but are different enough to justify having separate part manuals. Product manuals shown on product pages of the Henke website are only for standard, current production products. Product manuals may be updated at anytime. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 5 of 28

Table of Contents Introduction 3 Contact Your Local Dealer For Parts & Service 4 Replacement Parts 4 Technical Service & Customer Support Inquiries 5 Is this your product manual? 5 CHAPTER 2: Parts And Assemblies 7 Optional Remote Grease Part Assemblies 8 Getting Started, And Taking Basic Precautions 10 Optional Remote Grease System Installation 11 PLP Remote Grease Assembly, Installation Instructions 11 CHAPTER 3: Maintenance 21 In Season Maintenance 22 End Of Season Maintenance 23 Torque Table Mild Steel 24 CHAPTER 4: Warranty & Dealer Procedure 25 HENKE LIMITED WARRANTY 26 Dealer Warranty Procedure 28 PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 6 of 28

CHAPTER 2: PARTS AND ASSEMBLIES PLEASE READ ENTIRE BOOK BEFORE INSTALLATION, OPERATION, OR MAINTENANCE. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 7 of 28

Optional Remote Grease Part Assemblies Table 2-1:Optional PLP Remote Grease Part Descriptions Quantity Description 4700-0311 12" Bulkhead, Remote Grease 4700-0310 18" Bulkhead, Remote Grease, 12 Port Holes 4700-0393 15" Bulkhead, Remote Grease, 10 Port Holes 7020029 Hex Capscrew, 3/8-16 x 1, GR.5 7030006 Nylock Nut, 3/8-16 GR.2 7090585 Double Hose Clamp 7090085 Grease Fitting, Straight, 1/8 NPT 7090812 Vinyl Hose Clamp, 1-7/8 ID, 1-Hose 7090815 1/4-28 MALE X 1/8 NPSF 7090816 JIC to Pipe Elbow 45 7090817 JIC Swivel Elbow 90 7090531 JIC to Pipe Elbow 90 7090532 JIC to Pipe Bulkhead with Lock nut 7111050 Hydraulic Hose, 1/8 100R7 X 28"T, -4 JIC F x -4 JIC F, Full Nylon Hose Length 7111051 Hydraulic Hose, 1/8 100R7 X 40"T, -4 JIC F x -4 JIC F, Full Nylon Hose Length 7111052 Hydraulic Hose, 1/8 100R7 X 52"T, -4 JIC F x -4 JIC F, Full Nylon Hose Length 7111054 Hydraulic Hose, 1/8 100R7 X 64"T, -4 JIC F x -4 JIC F, Full Nylon Hose Length 7210017 Black Cable Tie, 14" UV 4700-0302 Pin, 3 x 33.75 x 3-Hole, Center Pin 149-0833 Pin, 1.25 x 6.44 x 5.13 1-Hole 4700-0060* Pin 3 x 33.75 3-Hole, with 4700-0302 149-0671* Pins 1.25 x 6.44 x 5.13 1-Hole, with 149-0833 7099011 Hydraulic Fitting 479-0007 Pin, 1 x 2.25 x 1-Hole, Cylinder Knuckle Pins 149-0648 Pin, 1.25 x 4.69 x 3.36 1-Hole, Rear Arm Pins * NOTE: Factory replaces non-grease-able pins with remote grease pins during factory install. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 8 of 28

Table 2-1:Comparison Of Optional PLP Remote Grease Assemblies Assembly No. Installed By Description 6382190 Factory FACTORY INSTALL, Grease Assembly, Includes all hoses Includes a negative Quantity of Center Pins For Inventory 6382191 Factory FACTORY INSTALL, Same as 6382190, except omits outer roller grease lines 6382192 Customer FIELD RETROFIT, version of 6382190 + rear arm and lift cylinder pin replacements Shipments BEFORE 06-01-2018 6382193 Customer FIELD RETROFIT, version of 6382190 Shipments AFTER 06-01-2018 (Already received grease-able arm and cylinder pins) 6382194 Customer FIELD RETROFIT, Same as 6382192, except omits 2 outer roller grease lines Shipments BEFORE 06-01-2018 6382195 Customer FIELD RETROFIT, Same as 6382193, except omits 2 outer roller grease lines Shipments AFTER 06-01-2018 (Already received grease-able arm and cylinder pins) Table 2-1:Optional PLP Remote Grease Assembly Quantities Part No. Quantity 6382190 6382191 6382193 6382195 6382192 6382194 Factory Install Factory Install Parts Kits Parts Kits Parts Kits Parts Kits 4700-0311 1 1 1 1 1 1 4700-0310 1 0 1 0 1 0 4700-0393 0 1 0 1 0 1 7020029 7 7 7 7 7 7 7030006 7 7 7 7 7 7 7090585 6 6 6 6 6 6 7090085 20 18 20 18 20 18 7090812 1 1 1 1 1 1 7090815 4 4 4 4 4 4 7090816 6 6 6 6 6 6 7090817 1 1 1 1 1 1 7090531 12 10 12 10 12 10 7090532 20 18 20 18 20 18 7111050 3 2 3 2 3 2 7111051 7 7 7 7 7 7 7111052 7 7 7 7 7 7 7111054 3 2 3 2 3 2 7210017 10 10 10 10 10 10 4700-0302 1 1 1 1 1 1 149-0833 2 2 2 2 2 2 4700-0060 -1* -1* 0 0 0 0 149-0671 -2* -2* 0 0 0 0 7099011 2 2 2 2 2 2 479-0007 0 0 0 0 8 8 149-0648 0 0 0 0 4 4 * NOTE: Factory replaces non-grease-able pins with remote grease pins during factory install. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 9 of 28

Getting Started, And Taking Basic Precautions STEP 1: STEP 2: STEP 3: STEP 4: STEP 5: PLEASE READ ENTIRE BOOK BEFORE INSTALLATION, OPERATION, OR MAINTENANCE. Verify you have all necessary parts and equipment for your Henke installation. Park the truck on a flat, level surface. Chock the tires. Refer to truck owner s manual for information about chocking the tires. Disconnect the battery when welding any items that are attached to the truck. Never weld items to a truck frame. Always use bolts. NOTE: Attempt to use existing bolt holes for attachment where available (assuming they are located properly and of the proper size). It is generally not advisable to bolt through the upper and lower flanges of the truck frame. When bolting a hitch to the front of the frame rails, however, bolting through the upper or lower flanges is typically not a problem, because the frame sees very little loading in this area. When bolting through the side (web) of the truck frame, avoid bolting extremely close to the upper and lower flanges. This rule can be relaxed for areas at the very front of the frame. When welds are called out in the instructions, use continuous 3/8 minimum fillet welds unless otherwise specified or appropriate. Fully torque all appropriate hardware before using Henke products. See torque table on page 1. SEE SEPARATE TABLE FOR APPROPRIATE TORQUE VALUES All References To "Left" And "Right" Are From The Driver's Perspective. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 10 of 28

Optional Remote Grease System Installation PLP Remote Grease Assembly, Installation Instructions Getting Started STEP 1: Read Getting Started And Taking Basic Precautions before continuing page 10. Verify Parts Received STEP 2: Verify you have received all parts from the appropriate assembly option listed on page 8. NOTES: To simplify the following instructions, the matching bulkhead hole, fitting(s), hose, and port hole all share the same ID number within the instructions. Example: Bulkhead hole 1, connects to hose 1, then to fitting(s) 1, and ends at port 1. Image schematics and tables are provided for visual guidance. Fitting orientation is important for best fit and function. See orientation notes listed in Table 2-2: page 17. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 11 of 28

STEP 1: Before Paint: Weld bulkhead 4700-0310 onto pushframe in the location shown in Figure 2-1: using the specified weld pattern. STEP 2: Fully weld head of (5) 7020029 bolts to plow in specified locations shown in Figure 2-1:. Figure 2-1:Welding Bolts And Bulkhead To Pushframe PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 12 of 28

STEP 3: Weld bulkhead 4700-0311 on the plow portion hitch in the location shown in Figure 2-2: page 13. Figure 2-2:Welding Bulkhead To Plow Portion Hitch STEP 4: Fully weld head of (2) 7020029 bolts to plow in specified locations shown in Figure 2-3:. Figure 2-3:Welding Bolts To Upper Arm PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 13 of 28

STEP 5: Replace all required pins if using assembly 6382192 or 6382194. STEP 6: Remove grease zerks from all pins, a total of (18) zerks. See locations (excluding 7 & 9) noted in Figure 2-5: page 15 and Figure 2-6: page 16. STEP 7: Grind and Paint welds as needed. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 14 of 28

After Paint: STEP 1: Install (20) 7090532 with (20) 7090085 into all open bulkhead locations, oriented so the hoses will connect as shown in Figure 2-4: page 15. Figure 2-4:Bulkhead Hole Location ID And Bulkhead Fitting Orientation NOTE: Top, Bottom, Left, and Right in this image are relative to the image, not relative to the driver. Figure 2-5:Plow Portion Hitch Port Locations PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 15 of 28

Figure 2-6:Pushframe Port Locations PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 16 of 28

STEP 2: Fitting ID Install Fittings and rotate them in the direction listed in Table 2-2: page 17 and shown in Figure 2-5: page 15 and Figure 2-6: page 16. Fitting Item Number Table 2-2:Fitting Identification And Matching Port Location Fitting Description Port Location Orientation Notes 1* 7090531 JIC to Pipe Elbow 90 1 Up at 45 toward plow 2 7090531 JIC to Pipe Elbow 90 2 Pointing outward 3 7090531 JIC to Pipe Elbow 90 3 Pointing outward 4 7090815 & 7090531 1/4-28 MALE X 1/8 NPSF & JIC to Pipe Elbow 90 4 Pointing downward 5 7090815 & 7090531 1/4-28 MALE X 1/8 NPSF & JIC to Pipe Elbow 90 5 Pointing upward 6 7090815 & 7090816 1/4-28 MALE X 1/8 NPSF & JIC to Pipe Elbow 45 6 Pointing left 7 7099011 JIC to Pipe Elbow 90, 3/8-18 NPT 7 MUST Point left 8 7090815 & 7090816 1/4-28 MALE X 1/8 NPSF & JIC to Pipe Elbow 45 8 Pointing left 9 7099011 JIC to Pipe Elbow 90, 3/8-18 NPT 9 MUST Point left 10* 7090531 JIC to Pipe Elbow 90 10 Up at 45 toward plow 11 7090531 JIC to Pipe Elbow 90 11 Pointing outward 12 7090531 JIC to Pipe Elbow 90 12 Pointing outward 13 7090816 JIC to Pipe Elbow 45 13 Pointing up and left 14 7090816 JIC to Pipe Elbow 45 14 Pointing up and right 15 7090816 JIC to Pipe Elbow 45 15 Pointing forward 16 7090816 JIC to Pipe Elbow 45 16 Pointing forward 17 7090531 JIC to Pipe Elbow 90 17 Pointing right 18 7090531 JIC to Pipe Elbow 90 18 Pointing left 19 7090531 JIC to Pipe Elbow 90 19 Parallel to arm tube 20 7090531 JIC to Pipe Elbow 90 20 Parallel to arm tube * NOTE: 6382191, 6382194, and 6382195 omit ports 1 & 10. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 17 of 28

STEP 3: STEP 4: Install the hoses into similarly numbered bulkhead hole. Hose identification is listed in Table 2-3: page 18. Connect the loose end of hoses to the simliarly numbered fitting listed in Table 2-3: page 18. Table 2-3:Hose Identification And Routing Chart NOTE: All hoses are 1/8" 100R7, -04 JIC Female, End To End, with Full Nylon Hose Sleeve. Hose ID Hose Item Number Total Hose Length Routes To Fitting # 1* 7111050 28" 1 2 7111051 40" 2 3 7111051 40" 3 4 7111051 40" 4 5 7111051 40" 5 6 7111052 52" 6 7 7111052 52" 7 8 7111052 52" 8 9 7111052 52" 9 10* 7111054 64" 10 11 7111054 64" 11 12 7111054 64" 12 13 7111050 28" 13 14 7111050 28" 14 15 7111052 52" 15 16 7111052 52" 16 17 7111051 40" 17 18 7111051 40" 18 19 7111051 40" 19 20 7111052 52" 20 * NOTE: 6382191, 6382194, and 6382195 omit ports 1 & 10. STEP 5: Install required clamps and cable ties as shown in Figure 2-7: page 19 through Figure 2-10: page 19. 5.1: Install clamp 7090812 on side swivel plate for hoses 4-9 (See Figure 2-8: page 19). 5.2: Clamp (5) 7090585 in all other locations for the following hose groups. 5.2.1: Hoses 2-3 (See Figure 2-7: page 19) 5.2.2: Hoses 10-12 to top of pushframe (See Figure 2-9: page 19) 5.2.3: Hoses 11-12 (See Figure 2-10: page 19) 5.2.4: Hoses 19-20 (See Figure 2-9: page 19) 5.2.5: Hose 20 5.3: Add zip tie to group together hoses 4-9 behind the bulkhead approximately 15 inches from bulkhead plate. 5.4: Add zip tie to group together hoses 15-18 at approximately 2.5 feet from bulkhead plate. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 18 of 28

5.5: Grease all lines and ensure grease contacts pins. Figure 2-7: Hose 2-3 Clamping Figure 2-8:Hose 4-9 Clamping Figure 2-9:Hose 10-12 Clamping Figure 2-10:Hose 11-12 Clamping PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 19 of 28

Figure 2-11:Hose 19-20 Clamping PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 20 of 28

CHAPTER 3: MAINTENANCE PLEASE READ ENTIRE BOOK BEFORE INSTALLATION, OPERATION, OR MAINTENANCE. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 21 of 28

In Season Maintenance Snow removal equipment must be cared for and maintained regularly. Daily or pre-route inspection and maintenance are necessary. Failure to do so may affect efficiency and safety. A visual inspection must be carried out after every 8 hours of operation. Look for damaged components, bends, cracked welds or hydraulic leaks. REPAIR IMMEDIATELY! Re-torque all bolts after the first 8 hours of use and to regularly check for loosened or missing fasteners. Replace any damaged or missing fasteners immediately. Because of the environment in which snow equipment is expected to operate, hydraulic lines, fasteners, wearable or replaceable items and warning decals may become damaged by snow, ice and road debris. These items must be inspected daily and replaced if necessary to avoid equipment damage or personal injury. Lubrication of moving parts is of the utmost importance. Exposure to snow, ice, salt and road debris will wash away lubrication quickly and it may be necessary to inspect and reapply lubrication more than once a day. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 22 of 28

End Of Season Maintenance GROUND ENGAGING COMPONENTS CUTTING EDGES & GUARDS: Replace any broken cutting edges, unevenly or excessively worn cutting edges, and broken or worn wear guards. RUNNING GEAR: Replace broken, worn, or missing running gear shoes, and any damaged adjuster leg components. Grease internal threads and sliding members (it s best to disassemble and grease directly; zerks aren t as effective at greasing these areas). HARDWARE: Replace missing or broken bolts. Proper torque is important! Use grade 8 plow bolts for steel cutting edges. HYDRAULICS HOSES: Plug or cap any QC fittings or any open hose ends. Inspect hoses for any leaks or potential leaks. Secure hoses with hose clamps. CYLINDERS: Check for leaks, and any chrome rod dents or scratches. Apply a light coat of oil or grease on exposed rod surfaces. FRAME AND MOLDBOARD JOINTS: Check pins, bushings, and pivot bolts for wear. Make sure all keepers are in place. Make sure shear bolts and pins are same as original equipment (usually grade 2). Some drivers don t like replacing shear pins and will install grade 8 replacements to avoid replacing during a storm. These items are designed to shear to protect driver and equipment. CHECK WELDMENTS FOR CRACKS. CABLE AND SHEAVES CABLE: Check cable thoroughly for fraying, kinks, and abnormal wear. Make sure cable is properly routed and seated in all sheaves. Verify that cable clamps have proper torque and are in correct orientation and spacing. Cable shall be checked prior to each use or after every 8 hours, whichever comes first. SHEAVES: Verify that sheave, bushings and retaining pins are in good condition and adequately greased. Make sure that sheaves, bushings and pins do not have any abnormal wear and rotate without restriction. REPLACE WORN OR BROKEN PARTS FOUND BY ABOVE INSPECTIONS PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 23 of 28

MAINTENANCE MAINTENANCE Spreader 01/16 Maintenance Section 4-6 2016 Alamo Group Inc.

CHAPTER 4: WARRANTY & DEALER PROCEDURE PLEASE READ ENTIRE BOOK BEFORE INSTALLATION, OPERATION, OR MAINTENANCE. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 25 of 28

1.0 LIMITED WARRANTIES HENKE LIMITED WARRANTY 1.1 Henke warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for twelve months to the original commercial or industrial purchaser 1.1.1 Parts manufactured by Henke are warranted to be free from defects in materials and/or workmanship for a period of 12 months from date of purchase when used under normal operating conditions, used in a proper application and have been provided any/all maintenance is performed as recommended. 1.1.2 Any parts or accessories not manufactured by Henke are warranted only to the extent that the manufacturer's warranty may be passed on to the purchaser and such parts and accessories are not subject to Henke's warranty or to any other warranty expressed or implied. 1.2 Manufacturer will repair or replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.3 This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This warranty does not include normal wear items such as cutting edges, wear guards, scarifier teeth, etc. or improper installation. HMC warranty for any purchased components, such as hydraulic cylinders will be superseded by, and equal to the component manufacturer warranty. 1.4 Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2.0 REMEDIES AND PROCEDURES. 2.1 Warranty claims must be filled within 30 days of repair work during the one year warranty period and will be honored only if the completed warranty registration form has been returned. Henke reserves the right to require proof of purchase of original Henke replacement parts. If warranty is approved any allowed shipping expenses will be based on and will not exceed standard base shipping charges. 2.2 Purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based. 2.3 Purchaser is responsible for returning the goods in question to the Dealer. 2.3.1 If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: 2.3.2 Repair or replace the defective goods or part(s) or 2.3.3 Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. 2.3.4 The choice of remedy shall belong to Manufacturer. 2.4 Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3.0 LIMITATION OF LIABILITY. 3.1 MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.2 MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.3 EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.4 NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4.0 MISCELLANEOUS. 4.1 Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Leavenworth County, Kansas. 4.2 Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.3 If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.4 Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

5.0 KEEP FOR YOUR RECORDS: ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Henke Product Model: Date Purchased: READ YOUR OPERATOR'S MANUAL Serial Number: Dealer: HENKE MANUFACTURING An Alamo Group Company 3070 WILSON AVE. LEAVENWORTH, KS 66048 (888) 682-9010

Dealer Warranty Procedure For units delivered within the past 12 months, report any warranty problems needing repair to our Product support department. Please have information ready regarding: 1. Henke unit model and serial number, 2. Model of equipment Henke unit is attached to (prime mover) 3. Description of the problem and any helpful information by the end user. (Photos are always helpful). Measurements or photos may be requested by Henke engineering for any issues regarding prime mover proximity and clearance, or any other unique considerations of fit and adaptability. These may be necessary for a proper repair recommendation and procedure. Henke will respond with a written labor hour allowance for Henke participation on a faxed claim form and will ship any required replacement parts. If necessary, a repair procedure will be included on the claim form. A parts invoice will be generated to confirm shipment of the replacement parts. If defective parts are needed for analysis, Henke will request their return. Any such returned items are to be labeled with the claim number and returned to: HENKE MANUFACTURING CORPORATION ATTN: Product Support 3070 WILSON AVE. LEAVENWORTH, KS 66048 RGA# The dealer should perform repairs as agreed on a dealer warranty repair order. Return the claim form with a copy of the dealer warranty repair order and service report. Credit as agreed will be issued to the dealer upon receipt of the dealer warranty repair order invoice (Pro-forma invoice), and upon receipt, inspection and warranty confirmation of the returned parts if any. Parts & Service Assistance Parts inquiries may be emailed at any time to parts@henkemfg.com. Emails are encouraged, as this will direct your inquiry to the entire parts and service team, insuring the most prompt attention possible. All inquiries are processed in the order they are received. Parts and service assistance is also available, Monday through Friday, from 7:00 am to 4:30 pm, CST, call (913) 682-9000 x3, or Toll Free (888) 682-9010 x3. Our web site, www.henkemfg.com, is a quick source for parts pricing, and many common parts diagrams. Go to www.henkemfg.com/parts-and-service/ to submit a quick request ticket for parts. PLP_REMOTE_GREASE_ASY_EFF_ALL_86382190_01_010 Page 28 of 28