APEM COMPONENTS LIMITED

APEM COMPONENTS LIMITED Designed and manufactured in the UK Illuminated pushbuttons and indicators, Keylock, Lever and Emergency Stop Switches

APEM designs and manufactures three product lines: miniature and industrial switches, switch panels for professional applications and specific assemblies. APEM rank amongst the world s largest manufacturers of both miniature and industrial switches with manufacturing sites in the United Kingdom, France and the United States. With several million part number variants corresponding to over 50 product families, APEM can meet all the requirements of miniature, sub-miniature and industrial switch markets. TOGGLE ROCKER PUSH BUTTON SLIDE TACTILE APEM INDICATORS MEMBRANE RELAYS D.I.L. SMT

A0 SERIES INDUSTRIAL CONTROLS Panel cut-out Ø6MM Page Contents NEW NEW 5 A0 - A0 Series Specifications 6 Illuminated or non-illuminated pushbutton switches 7 Indicators 8 Rotary lever switches 9 Keylock switches 0 Emergency stop switches Emergency stop enclosure switches Mushroom head pushbutton switches Custom engraved aluminium pushbutton switches 4 Accessories 5 Accessories 6 Installation/accessories

A0 SERIES/A0 SERIES/PUSH-PULL SERIES INDUSTRIAL CONTROLS Panel cut-out Ø-Ø0MM Page Contents NEW NEW NEW 7 Illuminated or non-illuminated pushbutton switches 8 Metal bezel pushbuttons and indicators 9 Flush mounting pushbuttons and indicators 0 Indicators Rotary lever switches Keylock switches Emergency stop switches 4 Mushroom head pushbutton switches 5 Installation/accessories 6 A0 Series range of pushbuttons/indicators 7 Push-pull switches 8 APEM special assemblies

A0 - A0 SERIES INDUSTRIAL CONTROLS Distinctive features A0 and A0 Series are designed and manufactured in the United Kingdom The A0 and A0 series offer ranges of: pushbutton switches, illuminated or not indicators or position keylock switches or position rotary lever switches emergency stop switches with rectangular, square or round operators. Environmental protection : IP65 Modular construction Electrical life : 50.000 cycles min. Screen engraving or insertable legends on request Approvals UL 054 BS RIA 0 Shock & Vibration VDE EN 6058 Sub-assembly For single part number assemblies please contact APEM Components A0/A/A0 Series A0 Series Panel cut-out : Ø 6mm (.60) flush mount : round Ø mm (.866) flush mount : rectangular 0.60 x 6.70mm (.8 x.05) flush mount : square 0.60 x 0.60 (.8 x.8) A flush mount : round Ø mm (.866) A0 round or square: Ø mm (.866) flush mount : Ø 0mm (.78) Panel cut-out : round or square : Ø mm (.866) rectangular : 9,5 x,5mm (.60 x.846) flush mount : Ø0mm (.78) and poles Screw terminals (optional : quick connect terminals),, and 4 poles Contacts : silver Solder lug/quick-connect terminals Contacts : silver, gold plated Current/voltage rating : A 80VAC - 6A 50VAC max. 5mA 5VAC min. Current/voltage rating : 6A 50VAC max. - 0mA 5VAC min. Lamp : filament, neon, multi-chip LED or special multi-led assembly Lamp : filament, neon or multi-chip LED For back of panel safety, this series has a unique covered cable connection arrangement. See page 5. 4

A0 - A0 SERIES INDUSTRIAL CONTROLS Specifications ELECTRICAL SPECIFICATIONS A0/A/A0 A0 Function : Momentary or maintained action Momentary or maintained action Current/voltage rating : 0mA 5VAC min. 5mA 5VAC min. 6A 50VAC max. 6A/VDC max. A 80VAC - 6A 50VAC max. A/VDC max. Contact gap : >mm (.09) Double break x,5mm (.059) Initial contact resistance : 0mΩ max. at A 4VDC 0mΩ max. at A 4VDC Insulation resistance : 50 MΩ min. 50 MΩ min. Dielectric strength : 750V between open contacts KV between open contacts 5KV live to accessible 4KV live to accessible Electrical life : 50.000 cycles min. 50.000 cycles min. Insulation : Class Class Lamp life : LED : 60.000 h min. to 75% relative LED : 60.000 h min. to 75% relative luminosity - Filament : approx. 5.000h luminosity - Filament : approx. 5.000h Neon : approx. 0.000 h Neon : approx. 0.000 h Lamp circuit diagrams A B A B GENERAL SPECIFICATIONS A0/A/A0 A0 Min. mechanical life : Pushbutton momentary : million cycles Pushbutton momentary : million cycles Pushbutton maintained : 00.000 cycles Pushbutton maintained : 00.000 cycles Keylock and rotary : 00.000 cycles Keylock and rotary : 00.000 cycles Operating temperature : -0 C to +55 C -0 C to +85 C Solder heat resistance : 50 C, 5 sec. 50 C, 5 sec. (IEC 68--0Tb, method ) Degree of environmental IP 65 front of panel IP 65 front of panel protection (IEC 59) IP 40 back of panel IP 40 back of panel Lamps : Midget Grooved T / 4 Midget Grooved T / 4 filament, multi-chip LED or neon filament, multi-chip LED or neon Special multi-led assembly Switch terminals : Solder/quick-connect,8mm (.0) M screws - wire x 0,75mm max. Lamp terminals : Solder/quick-connect,8mm (.0) M screws Flexible wire x,5mm max. Rigid wire 4mm max For screen engraving or film legends, consult factory. For approved models consult APEM. 5

A0 SERIES ILLUMINATED OR NON-ILLUMINATED PUSHBUTTON SWITCHES Panel cut-out Ø6 (.60) A pushbutton assembly requires: screen + lamp (if illuminated) + operator + switchblock To order these elements, select desired model numbers from tables below. Example: IP65 rectangular pushbutton, single pole, maintained, red screen and V red LED = A06B, A04M, A00X and A05B 6.5 (.640) 9.00 (.54).00 (.47) 6.00 (.6) 0.00 4.00 (.654) (.94 ) 9.00 (.54) 7.65 (.0) 7.65 (.0) 6.00 (.6) 7.65 (.0) 8.40 (.0) C 6.00 (.6) D 8.50 (.5) 8.50 (.) 4.00 (.945) C D E F 8.00x 4.0 0 (.945) (.709 SQ) 0.50 (.00).80 (.0) 0.70 (.09) Ø 8.0 0 (.709 DIA) 4 Screen Lamp Operator Switch block Bezel Colour Lamp Voltage Pole Bezel Description No of poles black red amber yellow green blue clear white black red amber yellow green blue clear white black red amber yellow green blue clear white A06A A06B A06C A06D A06E A06F A06G A06J A06A A06B A06C A06D A06E A06F A06G A06J A06A A06B A06C A06D A06E A06F A06G A06J Filament 6.V A04A Filament 4V A04B Filament 8V A04C Filament 6V A04D Filament 48V A04E Filament 60V A04F Neon 0V A04G Neon 0V A04H LED 6V red A04L LED 6V green A04L LED 6V amber A04L LED V red A04M LED V green A04M LED V amber A04M LED V blue A04M4 LED V white A04M5 LED 4V red A04N LED 4V green A04N LED 4V amber A04N LED 4V blue A04N4 LED 4V white A04N5 LED 48V red A04P LED 48V green A04P LED 48V amber A04P or Illum, momentary A00Y or Illum, maintained A00X or Non-illum, momentary A00Y or Non-illum, maintained A00X or 4 Illum, momentary A00Y or 4 Illum, maintained A00X or 4 Non-illum, momentary A004Y or 4 Non-illum, maintained A004X or Illum, momentary A005Y or Illum, maintained A005X or Non-illum, momentary A006Y or Non-illum, maintained A006X or 4 Illum, momentary A007Y or 4 Illum, maintained A007X or 4 Non-illum, momentary A008Y or 4 Non-illum, maintained A008X or Illum, momentary A009Y or Illum, maintained A009X or Non-illum, momentary A00Y or Non-illum, maintained A00X or 4 Illum, momentary A0Y or 4 Illum, maintained A0X or 4 Non-illum, momentary A0Y or 4 Non-illum, maintained A0X Single pole Double pole Three pole Four pole A05B A05B A055B A05B Unsealed switches (IP40): add 0 to end of operator model number Screen engraving/ insertable legends: contact APEM Components Bi-colour LEDs optional Bezel: rectangular square round. Illum - illuminated, Non-illum - non illuminated 6

A0 SERIES INDICATORS Panel cut-out Ø6 (.60) An indicator assembly requires: screen + lamp + operator To order these elements, select desired model numbers from tables below. Example: IP65 rectangular indicator with red screen and V red LED = A06B, A04M and A07 4.00 Ø (.945) (.709 DIA) 4.00 0.00 (.654) (.94) 8.40 (.0) 8.50 (.5) 0.50.80 (.00) (.0) Screen Lamp Operator Bezel Colour Lamp Voltage Bezel Description black red amber yellow green blue clear white black red amber yellow green blue clear white black red amber yellow green blue clear white A06A A06B A06C A06D A06E A06F A06G A06J A06A A06B A06C A06D A06E A06F A06G A06J A06A A06B A06C A06D A06E A06F A06G A06J Filament 6.V A04A Filament 4V A04B Filament 8V A04C Filament 6V A04D Filament 48V A04E Filament 60V A04F Neon 0V A04G Neon 0V A04H LED 6V red A04L LED 6V green A04L LED 6V amber A04L LED V red A04M LED V green A04M LED V amber A04M LED V blue A04M4 LED V white A04M5 LED 4V red A04N LED 4V green A04N LED 4V amber A04N LED 4V blue A04N4 LED 4V white A04N5 LED 48V red A04P LED 48V green A04P LED 48V amber A04P Indicator Indicator Indicator A07 A07 A07 Unsealed switches (IP40): add 0 to end of operator model number Screen engraving/insertable legends: contact APEM Components Bezel: rectangular square round. 7

A0 SERIES ROTARY LEVER SWITCHES Panel cut-out Ø6 (.60) A rotary level switch assembly requires: operator + switchblock To order these elements, select desired model numbers from tables below. Example: IP65 rectangular rotary switch with long lever, single pole, positions maintained = A090 and A05B.00 (.47) 6.00 (.6) 4.00 (.945) 4.00 0.00 (.654) (.94) 7.65 (.0) 8.40 (.0) 7.40 (.685) C D 8.50 (.) 4.00 (.945) C D E F x (.709 SQ) Ø (.709 DIA) 0.50 (.00).80 (.0) 0.70 (.09) Lever Positions Operator Switch block Pole Bezel Description Short lever Long lever No of poles or pos. maintained A090 A090 or pos. momentary A090 A090 or 4 pos. maintained A090 A090 or 4 pos. momentary A0904 A0904 or pos. maintained A0905 A0905 or pos. momentary A0906 A0906 or pos. mainl, momr A0907 A0907 or pos. moml, mainr A0908 A0908 or pos. maintained A0940 A090 or pos. momentary A0940 A090 or 4 pos. maintained A0940 A090 or 4 pos. momentary A09404 A0904 or pos. maintained A09405 A0905 or pos. momentary A09406 A0906 or pos. mainl, momr A09407 A0907 or pos. moml, mainr A09408 A0908 or pos. maintained A0960 A0950 or pos. momentary A0960 A0950 or 4 pos. maintained A0960 A0950 or 4 pos. momentary A09604 A09504 or pos. maintained A09605 A09505 or pos. momentary A09606 A09506 or pos. mainl, momr A09607 A09507 or pos. moml, mainr A09608 A09508 Single pole Double pole Three pole Four pole A05B A05B A055B A05B Note: /4 pole switch block for use only with position rotary lever Clockwise Rotation Anticlockwise Rotation Lever Rotation position switches The model numbers shown are for switches with anticlockwise lever rotation. For clockwise rotation, replace: 0 with 09 0 with 0 0 with 04 with at the end of the model number Optional engraving on lever end add WL to the end of the part number. Bezel: rectangular square round. pos - position, mainl - maintained left momr - momentary right, etc 8

A0 SERIES KEYLOCK SWITCHES Panel cut-out Ø6 (.60) An keylock assembly requires: operator + switchblock To order these elements, select desired model numbers from tables below. Example: IP65 rectangular keyswitch, single pole, positions maintained = A080 and A05B.00 (.47) 6.00 (.6) 4.00 (.945) 7.65 (.0) 4.00 (.945) x (.709 SQ) 4.00 8.00 (.654) (.496) 0.50 (.00) 8.40 (.0) C D.80 (.0) 8.50 (.) C D E F Ø (.709 DIA) 0.70 (.09) Key Positions Operator Switch block B C Pole Bezel Description. Key removable No of poles or pos. maintained A080 A-C or pos. momentary A080 A or 4 pos. maintained A080 A-C or 4 pos. momentary A0804 A or pos. maintained A0805 A-B-C or pos. momentary A0806 A or pos. mainl, momr A0807 A-B or pos. moml, mainr A0808 A-C or pos. maintained A080 A-C or pos. momentary A080 A or 4 pos. maintained A080 A-C or 4 pos. momentary A0804 A or pos. maintained A0805 A-B-C or pos. momentary A0806 A or pos. mainl, momr A0807 A-B or pos. moml, mainr A0808 A-C or pos. maintained A080 A-C or pos. momentary A080 A or 4 pos. maintained A080 A-C or 4 pos. momentary A0804 A or pos. maintained A0805 A-B-C or pos. momentary A0806 A or pos. mainl, momr A0807 A-B or pos. moml, mainr A0808 A-C Single pole Double pole Three pole Four pole A05B A05B A055B A05B Non-removable key positions: contact APEM components standard keys are supplied 0 key barrel types available from stock For on-on-on function contact APEM components Note: /4 pole switch block for use only with position key switches Clockwise Rotation Key Rotation position switches The model numbers shown are for switches with anticlockwise key rotation. For clockwise rotation, replace: 0 with 5 0 with 4 0 with 7 04 with 8 at the end of the model number A Anticlockwise Rotation Bezel: rectangular square round. pos - position, mainl - maintained left momr - momentary right, etc 9

A0 SERIES EMERGENCY STOP SWITCHES Panel cut-out Ø6 (.60) Prominent Ø 4mm (.944) or optional Ø 40mm (.575) dia. red mushroom actuator Highly reliable positive break switch Push to shut off switch, twist to reset to ON An emergency stop switch assembly requires: operator + switch block To order specify with single pole or double pole positive break switch block. Approved to UL054/EN 60947-5- N.C. General Specifications Electrical Specifications Min. Mechanical Life : 6050 cycles (6 cycles per minute) Operating Force : 6N 0.Nm Operating Temperature : -0 C to +55 C Solder Heat Resistance : 50 C, 5 secs (IEC 68---0Tb, method ) Degree of Environmental : IP65 front of panel Protection (IEC 59) IP40 back of panel Switch Terminals : Solder/quick-connect.8mm (.0) (IEC 68--0) Current/Voltage rating :.5A 50 VAC AC-5 Contact Gap : >mm Dielectric test voltage : 900V Electrical Life : >6050.00 (.47) 5.0 (.60) 4.00 9.00 (.654) (.047) Ø4.00 (.945 DIA) 8.40 (.0) C D Ø4.00 (.945 DIA) Option: SP Version 0.50 (.00).80 (.0) Ø40.00 (.575 DIA) Accessories 9.00 (.4) Operator Bezel Description Emergency stop A0ES Option 40Ømm Emergency stop A0ES SP Switch block No of poles Single pole A050B Double pole A054B 60Ø Self Adhesive Label.00 (.87) Description Yellow label with text Yellow label 64.00 (.50) A0YL A0YL 0

A0 SERIES EMERGENCY STOP SWITCHES/MUSHROOM HEAD PUSHBUTTON SWITCHES Fitted in Enclosures Prominent Ø 40mm (.575) dia. red mushroom actuator, twist to release Robust polycarbonate enclosures Highly reliable positive break switching on E-stop Sealed to IP65 6A current rating Knockouts for popular conduit sizes Double pole changeover switch blocks available for momentary/maintained mushroom head pushbuttons N.C. Emergency Stop Technical Specifications Contact Rating : 6A 50 VAC/.5A 50 VAC E-Stop Dimensions : 65 x 65 x 57mm Electrical Life : 50,000 cycles/6050 cycles E-Stop Operating Temperature : -0 C +55 C Momentary and Maintained Ø40.0 (.575 DIA) 55.0 (.67) 7.5 (.689) 65.0 SQUARE (.56) Description Emergency Stop Black Momentary Red Momentary Yellow Momentary Green Momentary Blue Momentary Black Maintained Red Maintained Yellow Maintained Green Maintained Blue Maintained A0ESSP54B + PEA0 A0MMASP5B + PEA0 A0MMBSP5B + PEA0 A0MMDSP5B + PEA0 A0MMESP5B + PEA0 A0MMFSP5B + PEA0 A0MXASP5B + PEA0 A0MXBSP5B + PEA0 A0MXDSP5B + PEA0 A0MXESP5B + PEA0 A0MXFSP5B + PEA0 Options A 50V versions or custom printing on mushroom head actuators please contact APEM Components.

A0 SERIES MUSHROOM HEAD PUSHBUTTON SWITCHES Panel cut-out Ø6 (.60) Prominent Ø 4mm (.944) or optional Ø 40mm (.575) dia. mushroom actuators Momentary and maintained functions. Momentary function versions are unmarked, maintained function versions are twist release (arrows indicate direction of twist) Various coloured mushroom actuators are available 4.00 9.00 (.654) (.047) 8.40 (.0) C D Ø4.00 (.945DIA) OPTION : SP VERSION 0.50 (.00).80 (.0) Ø40.00 (.575 DIA) Operator Actuator Description Switch block No of poles 4mmØ Black Momentary A0MMA 4mmØ Red Momentary A0MMB 4mmØ Yellow Momentary A0MMD 4mmØ Green Momentary A0MME 4mmØ Blue Momentary A0MMF 4mmØ Black Maintained A0MXA 4mmØ Red Maintained A0MXB 4mmØ Yellow Maintained A0MXD 4mmØ Green Maintained A0MXE 4mmØ Blue Maintained A0MXF 40mmØ Black Momentary A0MMA SP 40mmØ Red Momentary A0MMB SP 40mmØ Yellow Momentary A0MMD SP 40mmØ Green Momentary A0MME SP 40mmØ Blue Momentary A0MMF SP 40mmØ Black Maintained A0MXA SP 40mmØ Red Maintained A0MXB SP 40mmØ Yellow Maintained A0MXD SP 40mmØ Green Maintained A0MXE SP 40mmØ Blue Maintained A0MXF SP Single pole Double pole Three pole Four pole A05B A05B A055B A05B

A SERIES ENGRAVED ALUMINIUM FLUSH MOUNTING PUSHBUTTON SWITCHES & INDICATORS Panel cut-out Ø An pushbutton assembly requires: Engraved screen + lamp (if illuminated) + operator + switch block + flush mount bezel To order these elements, select desired model numbers from the table below. Example: Pushbutton, round, illuminated, sealed to IP 65, latching, single pole with start engraving, 4V blue LED and flush mounting bezel. APCAX0K40. Ø5.00 (9.85 DIA) 4.05 (.655) 8.5 (.5) 4.5 (.57).00 (.47) 7.65 (.0) 5. (.60).8 (.0) 0.5 (.00) A Accessories 0 - flushmount Switch Type Bezel Illumination Sealing Function Switch Block Bulb P - pushbutton I - indicator C - round A - illuminated B - non-illum. 0 - Front Fog Lights 0 - Rear Fog Lights 0 - Start 04 - Interior Light 05 - Boot Release 06 - Hazard Warning 07 - Lights 0 - unsealed - sealed IP65 08 - Heating and Ventilation 0 - indicator X - latching Y - momentary Engraved Screen Options - Lock - Unlock - Rear Window Heating 4 - Cooling 5 - Wipers 6 - Washers 7 - Fan 8 - Horn 0 - indicator - single pole - double pole 5 - three pole - four pole A - filament 6.v B - filament 4v C - filament 8v D - filament 6v E - filament 48v F - filament 60v G - Neon 0v H - Neon 0v I - Led 6v red I - Led 6v green I - Led 6v amber J - Led v red J - Led v green J - Led v amber J4 - Led v blue J5 - Led v white K - Led 4v red K - Led 4v green K - Led 4v amber K4 - Led 4v blue K5 - Led 4v white L - Led 48v red L - Led 48v green L - Led 48v amber For other screen engraving options contact APEM Components. Max. panel thickness 8mm. 09 - Map Lights 0 - Side Lights 9 - Air recirculation 0 - Blank

A0 SERIES INDUSTRIAL CONTROLS Accessories FLUSH MOUNTING BEZELS Dark grey plastic material supplied with sealing washer 8.0 (.7) 0.40 (.80) Ø6.00 (.60DIA).80 (.97) 8.0 (.7) 0.40 (.80) Ø6.00 (.60DIA).80 (.97) 8.5 (.75) Ø.00 (.866 DIA) Ø6.00 (.60DIA) Ø5.00 (.984 DIA).00 (.47) 9.80 (.7).00 (.47).80 (.97).00 (.4) +0.0 6.70 0.00 +.008 (.05.000 ) +0.0 0.60 0.00 +.008 (.8.000 ) +0.0 0.60 0.00 +.008 (.8.000 ) +0.0.0 0.00 +.008 (.874.000 ) Rectangular A0FM Square A0FM Round A0FM * FLUSH MOUNTING BEZELS Anodised aluminium/matt black 8.5 (.75) Ø.00 (.866 DIA) Ø6.00 (.60DIA) Ø5.00 (.984 DIA) 8.5 (.75) Ø.00 (.866 DIA) Ø6.00 (.60DIA) Ø5.00 (.984 DIA).00 (.4).00 (.4) +0.0.0 0.00 +.008 (.874.000 ) +0.0.0 0.00 +.008 (.874.000 ) Round A0FMM Round A0FMMG PCB SOCKET 5.00 (.96) 0.5 (.40) (.708) 6.00 (.6) 7.65 (.0) (.708) 7.65 (.0) 0.80 (.0) No of poles Single pole, non illuminated Double pole, non illuminated Single pole, illuminated Double pole, illuminated Indicator Single pole, E-stop Double pole, E-stop A0PC A0PC A0PC A0PC4 A0PC5 A0PC6 A0PC7 6.00 (.6) 4.5 (.67).0 (.04) 4.5 (.67) FLAPGUARDS 4.00 (.945).00 (.47).50 (.5) 4.00 (.945) 4.00 (.945).50 (.5) 9.00 (.54) (.708).65 (.57).65 (.57) Rectangular A0FG Square/round A0FG 4

A0 SERIES Accessories METAL GUARDS Slot as alternative to Ømm hole. Material : mm thick aluminium. 4.00 (.944) Ø.00 (.078DIA) (.708) Ø6.00 (.60DIA) 0.5 (.99).00 (.47) (.708).00 (.47) 8.0 (.77) Ø6.00 (.60DIA) Ø 9.60 Ø 6.05 Rectangular A0MG Square A0MG Round A0MG 9.00 0.00 Matt Black Option use. A0MGG ANTI ROTATION RING Recommended to prevent product rotation Ø6.00 (.69DIA) (.708) 4.75 (.580) A0LW (.708).00 (.078) ALUMINIUM SCREENS For non-illuminated pushbuttons For illuminated pushbuttons SWITCHBLOCK TERMINAL GUARDS A06AL A06AL 0.75 0.50 BLANKING PLUGS way A0RTC 8 way A0RTC8 4.0 Ø8.0 (.946)(.709 DIA) 8.0 4.0Ø8.0 (.946) (.709 DIA) 8.0 8.0 8.0 5.00 (.97) Ø5.00 (.59 DIA) Ø.00 5.00 (.97) Ø5.00 (.59 DIA) 0.75 0.75 7.45 7.45 0.00 7.5.0 4.85 0.00 0.50 0.00 0.50 8.50 0.75 6.00 6.00 0.75 Rectangular A0 Square A0 Round A0 RESISTOR ASSEMBLY Resistor assembly stage illumination A05B + RISSP (DIM) normally closed (BRIGHT) normally open 5

A0 SERIES INDUSTRIAL CONTROLS Installation tools EMERGENCY STOP ROTARY LEVER SWITCHES KEYLOCK SWITCHES PUSHBUTTONS & INDICATORS SCREEN LEGEND REFLECTOR PANEL CUT-OUT Round & square operators only Ø6.00 0.00/+0.0 (.69 DIA.000/+.0) LOCATING SLOT BULB POLARISING DOT 7.5 (.85).50 (.059) PANEL SEAL Rectangular operators only FIXING NUT OPERATOR 8.00 max (.4 max) Ø6.00 0.00/+0.0 (.69 DIA.000/+.0) Ø.00 (.078 DIA) LATCH SWITCH BLOCK 0.50 (.4) Max. panel thickness : 8mm (.4) PANEL MOUNTING ASSEMBLY Drill/punch hole shaped as above. Assemble front operator through hole, fit fixing nut and tighten to a maximum torque of 0.8Nm using tool No. 0-000. Wire chosen switch block as required and slide onto operator until latch engages. Fit bulb if required using tool No. 0-000. Snap screen onto reflector assembly with legend in between if required and snap onto front operator TAKING CARE TO LINE UP THE LOCATING SLOT WITH THE POLARISING DOT, and not to damage the seal. TO REMOVE BULB Remove reflector/screen assembly. Use the bulb extractor 0-000 to remove the bulb. SWITCH BLOCK To assemble switch block to front operator, firstly, TAKE CARE TO LINE UP SWITCH BLOCK WITH FRONT OPERATOR. Once in position slide on to front operator. N.B. Ensure latch is fully engaged correctly onto the switch block. To remove switch block, depress the latch and slide the switch block off the operator. FIXING NUT KEY BULB REMOVER 0-000 0-000 6

A0 SERIES ILLUMINATED OR NON-ILLUMINATED PUSHBUTTON SWITCHES Panel cut-out Ø or 9.5 x.5 A pushbutton assembly requires: screen + lamp (if illuminated) + operator + one or two switchblocks To order these elements, select desired model numbers from tables below. Example: IP65 rectangular maintained pushbutton, switch blocks with N.O. contacts, red screen and V red LED assembly = A06B, A04J, A00X and A050. N.O. N.C. N.O./N.C. 9.00 (.4) 6.00 (.47) 0.00 (.94) 55.50 (.85) 0.00 (.94) 4.00 (.945) 64.00 (.50) 64.00 0.00 (.50) (.94) 9.00x9.00 (.4 SQ).50.00 (.9) (.87) 7.00 (.06).00 (.87) Ø9.00 (.4 DIA).50 (.9) Screen Lamp Operator Switch block Bezel Colour Lamp Voltage Bezel Description Lamp type Contacts black red amber yellow green blue clear white black red amber yellow green blue clear white black red amber yellow green blue clear white A06A A06B A06C A06D A06E A06F A06G A06J A06A A06B A06C A06D A06E A06F A06G A06J A06A A06B A06C A06D A06E A06F A06G A06J Filament 6.V A04A Filament 4V A04B Filament 8V A04C Filament 6V A04D Filament 48V A04E Filament 60V A04F Neon 0V A04G Neon 0V A04H LED lamp model numbers see Pages 6&7 Special LED Assemblies LED assy 6V A04H* LED assy V A04J* LED assy 4V A04K* LED assy 6V A04H* LED assy V A04J* LED assy 4V A04K* LED assy 6V A044H* LED assy V A044J* LED assy 4V A044K* NB Replace * with colour code for LED assemblies: : red : green : amber Illum, momentary Lamp/LED bulb A00Y Illum, maintained Lamp/LED bulb A00X Illum, momentary Special LED assy A00Y Illum, maintained Special LED assy A00X Non-illum, momentary A00Y Non-illum, maintained A00X Illum, momentary Lamp/LED bulb A004Y Illum, maintained Lamp/LED bulb A004X Illum, momentary Special LED assy A005Y Illum, maintained Special LED assy A005X Non-illum, momentary A006Y Non-illum, maintained A006X Illum, momentary Lamp/LED bulb A007Y Illum, maintained Lamp/LED bulb A007X Illum, momentary Special LED assy A008Y Illum, maintained Special LED assy A008X Non-illum, momentary A009Y Non-illum, maintained A009X White or Blue LED Assembly: contact APEM Components Screen engraving/insertable legends: contact APEM Components N.O. A050 N.C. A050 N.O. A050 N.C. A0504 N.O./ N.C. A0505 Second switch block Contacts N.O. A0506 N.C. A0507 N.O. A0508 N.C. A0509 N.O./ N.C. A050 To achieve or 4 pole switching, add second switch block from above table. Unsealed switches (IP40): add 0 to end of operator model number Bezel: rectangular square round. Illum - illuminated, Non-illum - non illuminated 7

A0 SERIES METAL BEZEL PUSHBUTTON SWITCHES AND INDICATORS Panel cut-out Ø A pushbutton assembly requires: screen + lamp (if illuminated) + operator + one or two switchblocks An indicator assembly requires : screen + lamp + operator Example: IP65 metal bezel maintained pushbutton, switch block with N.O. contacts, red screen and V red LED assembly = A06B, A044J, A0X and A050 N.O. N.C. N.O./N.C. Ø9.00 (.4DIA) 45.50 (.79).50 (.45) 75.00 (.95) Ø9.00 (.4DIA) 4.00 (.8).00 (.86) 4 Screen Lamp Operator Switch block Bezel Colour Lamp Voltage Bezel Description Lamp type Contacts black red amber yellow green blue clear white A06A A06B A06C A06D A06E A06F A06G A06J Filament 6.V A04A Filament 4V A04B Filament 8V A04C Filament 6V A04D Filament 48V A04E Filament 60V A04F Neon 0V A04G Neon 0V A04H LED lamp model numbers see Pages 6&7 Special LED Assemblies LED assy 6V A044H* LED assy V A044J* LED assy 4V A044K* NB Replace * with colour code for LED assemblies: : red : green : amber White or Blue LED Assembly: contact APEM Components Illum, momentary Lamp/LED bulb A00Y Illum, maintained Lamp/LED bulb A00X Illum, momentary Special LED assy A0Y Illum, maintained Special LED assy A0X Non-illum, momentary A0Y Non-illum, maintained A0X Illum, indicator Lamp/LED bulb A077 Illum, indicator Special LED assy A078 Std bezel material : nickel plated brass For optional black finish, add G to the end of operator model number. Unsealed switches (IP40): add 0 to end of operator model number Screen engraving/insertable legends: contact APEM Components N.O. A050 N.C. A050 N.O. A050 N.C. A0504 N.O./ N.C. A0505 Second switch block Contacts N.O. A0506 N.C. A0507 N.O. A0508 N.C. A0509 N.O./ N.C. A050 To achieve or 4 pole switching, add second switch block from above table. Bezel: round. Illum - illuminated, Non-illum - non illuminated 8

A0 SERIES FLUSH MOUNTING PUSHBUTTON SWITCHES AND INDICATORS Panel cut-out Ø0 A pushbutton assembly requires: screen + lamp (if illuminated) + operator + one or two switchblocks An indicator assembly requires : screen + lamp + operator Example: IP65 flush mounting maintained pushbutton, switch block with N.O. contacts, red screen and V red LED assembly = A06B, A044J, A0X and A050 N.O. N.C. N.O./N.C..00 (.078) fl5.00 (.78 DIA).0 TO 6.0 PANEL THICKNESS 7.00 (.874) 46.00 (.8) fl5.00 (.78 DIA) 4.00.00 (.8) (.86) 4 Screen Lamp Operator Switch block Bezel Colour Lamp Voltage Bezel Description Lamp type Contacts black red amber yellow green blue clear white A06A A06B A06C A06D A06E A06F A06G A06J Filament 6.V A04A Filament 4V A04B Filament 8V A04C Filament 6V A04D Filament 48V A04E Filament 60V A04F Neon 0V A04G Neon 0V A04H LED lamp model numbers see Pages 6&7 Special LED Assemblies LED assy 6V A044H* LED assy V A044J* LED assy 4V A044K* NB Replace * with colour code for LED assemblies: : red : green : amber White or Blue LED Assembly: contact APEM Components Illum, momentary Lamp/LED bulb A04Y Illum, maintained Lamp/LED bulb A04X Illum, momentary Special LED assy A0Y Illum, maintained Special LED assy A0X Non-illum, momentary A05Y Non-illum, maintained A05X Illum, indicator Lamp/LED bulb A079 Illum, indicator Special LED assy A079 Std bezel material : silver anodised aluminium. For optional black anodised aluminium, add G to the end of operator model number. Unsealed switches (IP40): add 0 to end of operator model number Screen engraving/insertable legends: contact APEM Components N.O. A050 N.C. A050 N.O. A050 N.C. A0504 N.O./ N.C. A0505 Second switch block Contacts N.O. A0506 N.C. A0507 N.O. A0508 N.C. A0509 N.O./ N.C. A050 To achieve or 4 pole switching, add second switch block from above table. Bezel: rectangular square round. Illum - illuminated, Non-illum - non illuminated 9

A0 SERIES INDICATORS Panel cut-out Ø or 9.5 x.5 An indicator assembly requires: screen + lamp, LED bulb or LED assembly + operator To order these elements, select desired model numbers from tables below. Example: rectangular indicator with red screen and V red LED assembly = A06B, A04J and A07 0.00 (.94) 6.00 (.47) 9.00 (.4) 4.00 (.945).50 (.9).00 (.87) 9.00x9.00 (.4 SQ) Ø9.00 (.4 DIA) 7.50 (.476) 0.00 (.94) 9.00 (.4).50 (.9).00 (.87) Screen Lamp Operator Bezel Colour Lamp Voltage Bezel Description Lamp type black red amber yellow green blue clear white black red amber yellow green blue clear white black red amber yellow green blue clear white A06A A06B A06C A06D A06E A06F A06G A06J A06A A06B A06C A06D A06E A06F A06G A06J A06A A06B A06C A06D A06E A06F A06G A06J Filament 6.V A04A Filament 4V A04B Filament 8V A04C Filament 6V A04D Filament 48V A04E Filament 60V A04F Neon 0V A04G Neon 0V A04H LED lamp model numbers see Pages 6&7 Special LED Assemblies LED assy 6V A04H* LED assy V A04J* LED assy 4V A04K* LED assy 6V A04H* LED assy V A04J* LED assy 4V A04K* LED assy 6V A044H* LED assy V A044J* LED assy 4V A044K* NB Replace * with colour code for LED assemblies: : red : green : amber Indicator Lamp/LED bulb A07 Indicator Special LED assy A07 Indicator Lamp/LED bulb A07 Indicator Special LED assy A074 Indicator Lamp/LED bulb A075 Indicator Special LED assy A076 White or Blue LED Assembly: contact APEM Components Screen engraving/insertable legends: contact APEM Components Unsealed indicators (IP40): add 0 to end of operator model number Bezel: rectangular square round 0

A0 SERIES ROTARY SWITCHES Panel cut-out Ø (.866) A rotary lever assembly requires: operator + one or two switchblocks To order these elements, select desired model numbers from tables below. Example: IP65 square position maintained rotary switch with long lever, switch block with N.O. contacts = A090 and A050. N.O. N.C. N.O./N.C. 9.00 (.4) 9.00x9.00 (.4 SQ) 64.00 (.50) 64.00 (.50) 0.00 (.787).00 (.866) Ø9.00 (.4 DIA).00 (.866).00 (.87) 7.00 (.06).50 (.9) Lever Positions Operator Bezel Description Short lever Long lever pos. maintained A090 A090 pos. momentary A090 A090 pos. maintained A090 A090 pos. momentary A0904 A0904 pos. mainl, momr A0905 A0905 pos. moml, mainr A0906 A0906 pos. maintained A0940 A090 pos. momentary A0940 A090 pos. maintained A0940 A090 pos. momentary A09404 A0904 pos. mainl, momr A09405 A0905 pos. moml, mainr A09406 A0906 To specify flush mounting (0mmØ) option: add FM to the end of the part number: Example: A0940FM (round operators only) Bezel: square round Contacts Switch block N.O. A050 N.C. A050 N.O. A050 N.C. A0504 N.O./ N.C. A0505 Second switch block Contacts N.O. A0506 N.C. A0507 N.O. A0508 N.C. A0509 N.O./ N.C. A050 To achieve or 4 pole switching, add second switch block from above table. Clockwise Rotation Lever Rotation position switches The model numbers shown are for switches with anticlockwise lever rotation. For clockwise rotation, replace: 0 with 07 0 with 08 at the end of the model number Optional Engraving on Lever End To order add WL to the end of the part number. Example: A0940WL Anticlockwise Rotation

A0 SERIES KEYLOCK SWITCHES Panel cut-out Ø or 9.5 x.5 A keylock assembly requires: operator + one or two switchblocks To order these elements, select desired model numbers from tables below. Example: IP65 square position maintained keyswitch, switch block with N.O. contacts = A080 and A050 N.O. N.C. N.O./N.C. 9.00 (.4) 6.00 (.47) 9.00x9.00 (.4 SQ) 55.50 (.85) 64.00 (.50) 4.00 (.945) 8.00 (.496) 4.50 (.58) Ø9.00 (.4 DIA).50 (.9).00 (.87) 7.00 (.06).00 (.87).50 (.9) Key Positions B C Operator Bezel Description. Key removable in positions pos. maintained A080 A-C pos. momentary A080 A pos. maintained A0805 A-B-C pos. momentary A0806 A pos. mainl, momr A0807 A-B pos. moml, mainr A0808 A-C pos. maintained A080 A-C pos. momentary A080 A pos. maintained A0805 A-B-C pos. momentary A0806 A pos. mainl, momr A0807 A-B pos. moml, mainr A0808 A-C pos. maintained A080 A-C pos. momentary A080 A pos. maintained A0805 A-B-C pos. momentary A0806 A pos. mainl, momr A0807 A-B pos. moml, mainr A0808 A-C To specify flush mounting (0mmØ) option: add FM to the end of the part number: Example: A080FM (round operator only) Contacts Switch block N.O. A050 N.C. A050 N.O. A050 N.C. A0504 N.O./ N.C. A0505 Second switch block Contacts N.O. A0506 N.C. A0507 N.O. A0508 N.C. A0509 N.O./ N.C. A050 To achieve or 4 pole switching, add second switch block from above table. Clockwise Rotation A Anticlockwise Rotation Key Rotation position switches The model numbers shown are for switches with anticlockwise lever rotation. For clockwise rotation, replace: 0 with 0 0 with 9 at the end of the model number standard keys are supplied 0 key barrel types available from stock Non-removable key positions: contact APEM components Bezel: rectangular square round. pos - position, mainl - maintained left momr - momentary right, etc

A0 SERIES EMERGENCY STOP SWITCHES Panel cut-out Ø (.866) Prominent 40mm (.575) dia. red mushroom actuator Highly reliable positive break switch Push to shut off switch, twist to reset to ON An emergency stop switch assembly requires: operator + switch block To order specify with single pole or double pole positive break switch block. Approved to UL054/EN 60947-5-5 N.C. General Specifications Electrical Specifications Min Mechanical Life : 6050 cycles (6 cycles per minute) Operating Force : 0N Operating Temperature : -0 C to +85 C Degree of Environmental : IP65 front of panel Protection (IEC 59) IP40 back of panel Switch Terminals : M screws-wire x 0.75mm max Current/Voltage rating :.5A 80VAC AC-5 Contact Gap : >mm Dielectric test voltage : 500V Electrical Life : >6050 9.00 (.4) Ø40.00 (.575 DIA) 64.00 (.50).00 (.87).00 (.87) Accessories Operator Bezel Description E-Stop operator A0ES No of poles Double pole Single pole Switch block A05 A05 To order the Emergency Stop Switch in the Plastic Enclosure with a Pole Positive break Switchblock and Emergency Stop label use part number: A0PEL 90Ø Self Adhesive Label Description Yellow label with text Yellow label A0YL A0YL Bezel: round.

A0 SERIES MUSHROOM HEAD PUSHBUTTON SWITCHES Panel cut-out Ø (.866) Prominent 40mm (.575) dia. mushroom actuator Momentary and maintained functions, momentary function versions are unmarked, maintained function versions are twist to release (arrows indicate direction of twist) Various coloured mushroom actuators are available N.O. N.C. N.O./N.C. 9.00 (.4) Ø40.00 (.575 DIA) 64.00 (.50).00 (.87).00 (.87) Operator Bezel Description Contacts Switch block Black momentary Red momentary Yellow momentary Green momentary Blue momentary Black maintained Red maintained Yellow maintained Green maintained Blue maintained A0MMA A0MMB A0MMD A0MME A0MMF A0MXA A0MXB A0MXD A0MXE A0MXF N.O. A050 N.C. A050 N.O. A050 N.C. A0504 N.O./ N.C. A0505 Second switch block Contacts For optional reduced (Ø6mm) mushroom head operators: contact APEM Components N.O. A0506 N.C. A0507 N.O. A0508 N.C. A0509 N.O./ N.C. A050 To achieve or 4 pole switching, add second switch block from above table. Bezel: round. 4

A0 SERIES INDUSTRIAL CONTROLS Installation Modular Construction/panel mounting PUSHBUTTONS & INDICATORS SCREEN LEGEND EMERGENCY STOP ROTARY LEVERS SWITCHES KEYLOCK SWITCHES REFLECTOR LOCATING SLOT BULB POLARISING DOT PANEL SEAL Ø.00 0.00/+0.50 (.866 DIA.000/+.09).00 (.8).00 (.5) FIXING NUT 8.00 max (.4 max) OPERATOR ADAPTOR BLOCK.50 0.00/+0.50 (.846.000/+.09 ) 9.50 0.00/+0.50 (.6.000/+.09) SWITCH BLOCK END CAP PANEL CLAMP FIXING SCREW PANEL MOUNTING ASSEMBLY Drill/punch hole in panel as shaped above. Assemble front operator through hole and: a) Round & Square types: tighten nut to a maximum torque of 0,8Nm using tool No. 0-000. Snap on adaptor block b) Rectangular types: tighten two panel fixing screws in front to a maximum torque of 6cNm. Wire chosen switch block as required and snap onto front operator. Snap end cap onto switch block (optional). Fit bulb if required using tool No. 0-000. Snap screen onto reflector assembly with legend in between if required and snap onto front operator TAKING CARE TO LINE UP THE LOCATING SLOT WITH THE POLARISING DOT, and not to damage the seal. A0 Accessories End cap terminal guard offering unique terminal protection.. 4-0005 TO REMOVE BULB Remove reflector/screen assembly. Use the bulb extractor 0-000 to remove the bulb. TO REMOVE SWITCH BLOCK Lever out latches using small screwdriver taking care not to overbend, and pull off the block from the front of operator. 6.5mm Push on tab terminals Specify SP to the end of the switchblock and operator part No. Example: A050SP Dimensions: First dimensions are in mm while inches are shown in bracketed numbers. Tolerance: The general tolerance for dimensions in this catalogue is +/- 0, (.0). Dimensions, specifications and data shown in this catalogue are subject to change without notice. 5

A0 SERIES ILLUMINATED OR NON-ILLUMINATED PUSHBUTTON SWITCHES & INDICATORS Panel cut-out Ø OR Ø0mm Plastic or Metal Flush Mounting Bezel A pushbutton assembly requires: screen + lamp (if illuminated) + operator + switchblock To order these elements, select desired model numbers from the table below. Example: IP65 flush mounting round pushbutton, maintained function, red screen, single pole switch block and v red LED = A04X, A06B, A04M and A05B Ø9.00 (.4 DIA) Ø5.00 (.79 DIA) 6.00 (.6) 6.00 (.6) 49.00 (.9) 6.00 (.04) 59.00 (.5) 59.50 (.44).0 to 6.0 Panel Thickness 0.00 (.94).00 (.079) 0.50 7.65 (.0) 4 Screen Lamp Operator Switch block Bezel Colour Lamp Voltage Bezel Description Lamp type No of poles black red amber yellow green blue clear white A06A A06B A06C A06D A06E A06F A06G A06J Filament 6.V A04A Filament 4V A04B Filament 8V A04C Filament 6V A04D Filament 48V A04E Filament 60V A04F Neon 0V A04G Neon 0V A04H LED 6V red A04L LED 6V green A04L LED 6V amber A04L LED V red A04M LED V green A04M LED V amber A04M LED V blue A04M4 LED V white A04M5 LED 4V red A04N LED 4V green A04N LED 4V amber A04N LED 4V blue A04N4 LED 4V white A04N5 LED 48V red A04P LED 48V green A04P LED 48V amber A04P Plastic illum, momentary Lamp/LED bulb A007Y Plastic illum, maintained Lamp/LED bulb A007X Plastic non-illum, momentary A009Y Plastic non-illum, maintained A009X Metal illum, momentary Lamp/LED bulb A00Y Metal illum, maintained Lamp/LED bulb A00X Metal non-illum, momentary A0Y Metal non-illum, maintained A0X F/mount illum, momentary Lamp/LED bulb A04Y F/mount illum, maintained Lamp/LED bulb A04X F/mount non-illum, momentary A05Y F/mount non-illum, maintained A05X Plastic indicator A075 Metal indicator A077 F/mount indicator A079 Single pole Double pole Three pole Four pole A05B A05B A055B A05B Unsealed switches (IP40): add 0 to end of operator model number Screen engraving/ insertable legends: contact APEM Components Bezel: round. Illum - illuminated, Non-illum - non illuminated 6

N SERIES PUSH-PULL SWITCHES Panel cut-out Ø Latching double pole changeover Ø4mm diameter operating button Selection of button colours Solder lug terminals 4 6 5 General Specifications Panel cut-out : mm dia. Actuator diameter : 4mm Travel :.mm Operating temperature : -0 C +70 C Panel thickness : 8mm max. Switch terminals : Solder lug Electrical Specifications Electrical function : Double pole changeover Maximum rating : A, 50V AC Contact resistance : 0 milliohms max Electrical life : 0,000 cycles at full load Ø4.00 (.945 DIA) 5.5 (.068).0 (.867) 0.0 (.94) OPERATED 55. (.75) 5.5 (.99) 9. (.760) Description Black plunger Red plunger Yellow plunger Green plunger Blue plunger N46A N46B N46D N46E N46F Options available 40mm head version Metal head version Custom printing on plunger please contact APEM components 7

APEM SPECIAL ASSEMBLIES A0 Flush mounting assemblies 5.0 Min 4.0 Min 4.0 Min 5.0 Min PANEL CUTOUT:-.0 dia +0.5-0.00 Round 4.0 Min PANEL CUTOUT:-.5/0.75 x 0.5/0.75 Square 0.0 Min PANEL CUTOUT:- 6.75/7.0 x 0.5/0.75 Rectangular For single part number assemblies, i.e. switch supplied with bulb, screen, legend and flush mounting bezel (if required) fitted, please contact APEM Components. Rectangular - APR******* Square - APS******* Round - APC******* * = To be confirmed by APEM Components APEM components are able to offer fully integrated switch and cable assemblies. Please contact APEM Components for further details. 8

Apem Components Limited Drakes Drive Long Crendon Bucks HP8 9BA United Kingdom Tel: (+44) 844 0400 Fax: (+44) 844 0500 Email: sales@apem.co.uk Website: www.apem.co.uk

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Apem: A4