ESO IC KORINN 8mm llargato MONOLOCK DIRECIONL CONROL VLVE
Features Simple, compact and heavy duty designed monoblock valves from to 7 sections for open and closed center hydraulic systems.. H Fitted with a main pressure relief valve and a load check valve. H vailable with parallel, series or tandem circuit. H Optional power beyond port (only for parallel or tandem circuit). H Diameter 6 mm --.63 in interchangeable spools. H wide variety of service port valve options. H ctuation is manual, pneumatic, electro--pneumatic, hydraulic, electro--hydraulic, with solenoid and remote with flexible cables spool control kits. dditional information his catalog shows the product in the most standard configurations. lease contact Customer Service Dpt. for more detailed information or special request. WRNING! ll specifications of this catalog refer to the standard product at this date. Walvoil, oriented to a continuous improvement, reserves the right to discontinue, modify or revise the specifications, without notice. WLVOIL IS NO RESONSILE FOR NY DMGE CUSED Y N INCORREC USE OF HE RODUC. 5 th edition November : his edition supercedes all prior documents. D3
Contents Contents Working conditions................................. 4 Dimensional data................................... 5 Hydraulic circuit.................................... 6 erformance data.................................. 7 Ordering codes..................................... 8 Inlet relief options.................................. Spool options..................................... side spool positioners.......................... 8 side options................................... 3 Complete control kits............................... 34 Outlet port options................................. 4 Service valves ordering codes................................. 4 port relief valves................................ 44 anti--shock valves.............................. 46 pilot operated check valves...................... 47 anti--shock and anti--cavitation valves............. 49 flow regulator valves............................ 5 Other execution monoblock valve SD5/--N....................... 54 monoblock valve SD5/--D....................... 55 monoblock valve SD5--S with series circuit......... 56 monoblock valve SD5--S with tandem circuit........ 58 Installation and maintenance........................ 6 ccessories...................................... 6 D3 3
Working conditions his catalog shows technical specifications and diagrams measured with mineral oil of 46 mm /s -- 46 cst viscosity at 4 C -- 4 F temperature. Nominal flow rating 45 l/min US gpm Operating pressure (maximum) parallel pr tandem circuit 35 bar 46 psi series circuit 5 bar 36 psi Max. back pressure on outlet port 5 bar 36 psi Internal leakage () Hydraulic fluid p= bar - 45psi fluid and valve at 4 C - 4 F 3 cm 3 /min.8 in 3 /min Mineral base oil Fluid temperature range with NR seals from -- to 8 C from -4 to 76 F with FM seals from -- to C from -4 to F Viscosity operating range from 5 to 75 mm /s from 5 to 75 cst minimum mm /s cst maximum 4 mm /s 4 cst Max. level of contamination 9/6 -- ISO 446 NS 638 - class mbient temperature range from --4 to 6 C from -4 to 4 F NOE -- For different conditions please contact Customer Service. 4 D3
Dimensional data (parallel circuit),5.6 E F ower beyond.8 63,5 3.5. 45.77 86 7.3 8 3.9 3 4.6 34.34 45,5.79 5. 8,5.33 spool out 3 45.77 3 3 37 7.9.8.46.6 WLVOIL SD5/-- 9 MDE IN ILY M 8,5.45.79 WLVOIL SD5/ - 9 MDE IN ILY 4,5.96 9 3.54 Valve type roduction batch: = production year () = progressive number Valve code 5 5 4 4 3 spool in YE E F Weight E F Weight YE mm in mm in kg lb mm in mm in kg lb SD5/ -.5 3.96 73.87 3.5 7.7 SD5/5-48.5 9.78 8.7..3 SD5/ - 37.5 5.4 4.33 5..5 SD5/6-85.5.4 58.6.7 5.8 SD5/3-74.5 6.87 47 5.79 6.9 5. SD5/7-3.5.7 95.6 3. 9. SD5/4 -.5 8.33 84 7.4 8. 7.9 Standard threads ORS S (ISO 8/) UN -UNF (ISO 96 -) MERIC (ISO 6) Inlet and power beyond C G 3/8 3/4--6 UNF-- (SE 8) M8x.5 and ports G 3/8 9/6--8 UNF-- (SE 6) M8x.5 Outlet G 3/8 3/4--6 UNF-- (SE 8) M8x.5 ILO ORS neumatic NF /8--7 NF /8--7 NF /8--7 Hydraulic G /4 9/6--8 UNF-- (SE 6) G /4 D3 5
Hydraulic circuit arallel Standard configuration with side inlet and outlet and open center (E execution). ositioner kit Check valve llen wrench 4 4 Nm / 7.7 lbft ort line ort line ressure line ank line Flow through (LC) Main relief valve lug for open center llen wrench 8 4 Nm / 7.7 lbft Lever pivot box Standard configuration Configuration with upper inlet and outlet 75 75 Ex.: SD5/--(JG3--)/8L/8L/E Ex.: SD5/--(JG3--)/8L/8L/E--S 6 D3
erformance data (pressure drop vs. flow) Open center From side inlet to side outlet. 3 3 4 5 6 7 4 5 6 7 ressure drop 4 (bar) 3 5 5 (US gpm) 54 (psi) 7 sections 4 sections 36 sections 8 5 3 45 6 Flow (l/min) Inlet to work port From side inlet to port (spool in position ) or port (spool in position ). 3 3 4 5 6 7 4 5 6 7 ressure drop 4 (bar) 3 5 5 (US gpm) 54 (psi) 7 ( 7 ) 36 ( ) 8 5 3 45 6 Flow (l/min) Work port to outlet From port (spool in position ) or port (spool in position ) to side outlet. 3 3 4 5 6 7 4 5 6 7 ressure drop 4 (bar) 3 5 5 (US gpm) 54 (psi) ( ) 36 7 ( 7 ) 8 5 3 45 6 Flow (l/min) NOE -- Measured with spool type. D3 7
Ordering codes Description example: Valve setting (bar) st section following section Valve setting (bar) SD5 / - (JG3 -) / 8 L / 8IM. 3(G3 -) / E - SE *.. 3. 4. 5. 6. 7. 8. 6. 9. I 8. 7. 4. 3. II.. 5.. ody kits * YE CODE DESCRIION - 5KC97 arallel, section - 5KC7 arallel, sections 3-5KC47 arallel, 3 sections 4-5KC77 arallel, 4 sections 5-5KC37 arallel, 5 sections 6-5KC357 arallel, 6 sections 7-5KC3E7 arallel, 7 sections Include boby, seals and load check valve.. Inlet relief options page YE CODE DESCRIION VMD5 direct pressure relief valve type J (JG-8) 5KI54 Range 4 to 8 bar / 58 to 5 psi standard setting 8 bar / 5 psi (JG3-) 5KI543 Range 63 to bar / 9 to 9 psi standard setting bar / 75 psi (JG4-) 5KI544 Range 6 to 35 bar / 3 to 46 psi standard setting bar / 3 psi Standard setting is referred to l/min -.64 US gpm flow. SV X638 Relief valve blanking plug 3. Spool options page YE CODE DESCRIION 3CU3 Double acting, 3 positions, with and closed in neutral position 3CU3 Double acting, 3 positions, with open to tank in neutral position 3CU3 Double acting, 3 positions, with open to tank in neutral position 3CU53 Double acting, 3 positions, with and open to tank in neutral position H 3CU55 Double acting, 3 positions, with e partially open to tank in neutral position 3 3CU33 Single acting on, 3 positions, plugged requires G3/8 plug (see part I ) Special spools for particular positioner kits............... page 4 5DY 3CU4 Double acting, 4 positions, floating circuit in 4 th position with spool in 5Y 3CU456 Double acting, 4 positions, floating circuit in 4 th position with spool out, fitted with check valve 8 3CU6 Double acting, 4 positions, regenerative circuit in 4 th position with spool in Special spools for standard positioner kits................ page 7 8F 3CU6 Double acting, 3 positions, regenerative circuit in nd position with spool out 8 D3
Codici di ordinazione 4. side spool positioners page 8 YE CODE DESCRIION 8 5V85 With spring return in neutral position 8D 5V85 With spring return in neutral position and pin with M6 female thread for dual control 8D 5V85 With spring return in neutral position and pin with M8 male thread for dual control 8F 5V85 With spring return in neutral position and adjustable flow limiter 9 5V95 positions, with spring return in neutral position from position 5V95 positions, with spring return in neutral position from position 9 5V95 With detent in position and spring return in neutral position 5V5 With detent in position and spring return in neutral position 5V5 Detent in positions neutral, and 5V5 Detent in positions and 5 5V55 positions, detent in positions and neutral 6 5V65 positions, detent in positions and neutral 9 5V9 With detent in position and spring return in neutral position 5V With detent in position and spring return in neutral position 5V Detent in positions and and spring return in neutral position 8MS3 5V85553 With spring return in neutral position, operation signalling in position and, prearranged for centralized microswitch control 8MG 5V8567 With spring return in neutral position and microswitch in position 8MG 5V8568 With spring return in neutral position and microswitch in position 8MG3 5V8566 With spring return in neutral position and microswitch in positions and 8M3 5V854 With spring return in neutral position and external pin for microswitch control in positions and 8EM 5V8558 With spring return in neutral position and VDC electromagnetic detent in pos. 5V8559 s previous, 4VDC 8MHE3(NC) 5V8554 With spring return in neutral position and spool postioning ON/OFF electric signal circuit normally closed 8MHE3(NO) 5V8554 s previous, with circuit normally open 8 5V857 ON/OFF pneumatic kit 8E3 5V85735 ON/OFF VDC electro -pneumatic kit 5V8574 ON/OFF 4 VDC electro -pneumatic kit 8ED3 5V8535 ON/OFF VDC electro -hydraulic kit 5V8535 ON/OFF 4 VDC electro -hydraulic kit articular positioner kits for special spools............... page 4 3NZ 5V335...4 positions with spring return in neutral pos. and detent in 4 th pos.: for spool 5DY 3QN 5V345 4 positions with spring return in neutral pos. and detent in 4 th pos.: for spool 5Y 3FZ 5V3554 4 positions with spring return in neutral position: for spool 8 5. side options page 3 YE CODE DESCRIION L 5LEV5 Standard lever box LM 5LEV5 Lever box for M handlever LF 5LEV5 Lever box with adjustable flow limiter LE 5LEV65 Safety lever box, vertical configuration LU 5LEV855 Safety lever box, horizontal configuration SL 5CO5 Witout lever box, with dust-proof plate SLC 5CO5 Witout lever box, with endcap Q 5EL5 Flexible cable connection LC 5CLO5 Joystick lever for sections operation 6. Complete spool control kits page 34 Hydraulic proportional and ON/OFF electric spool control kits. 7. Service valves page 4 ort relief, anti--shock, pilot operated check and flow regulation valves. 8. Outlet port options pag. 4 YE CODE DESCRIION E X637 Open center plug EK 3X58 Closed center plug E 3XGIU5747* SE8 power beyond sleeve E -L 5CR457* With hydraulic pilot unloader valve E -EL YCR4535 With VDC electric control unloader valve YCR453 With 4VDC electric control unloader valve E -L X5337 rearranged for unloader valve, with blanking plug 9. Inlet and outlet selection * page 6 YE CODE DESCRIION SL 3X85 Side ports; need n. SE8 plugs, standard configuration (omit in valve description) S 3X85 Upper ports; need n. SE8 plugs I and ports plugs * YE CODE DESCRIION SE6 3X873 For single acting spool type 3 II Optional handlevers YE CODE DESCRIION L/M8x 7 For lever L: height mm / 4.7 in L/Mx5 75 For lever LM: height 5 mm / 5.9 in L8/Mx5 735 For joystick LC: height 5 mm / 5.9 in NOE (*) - Codes are referred to UN- UNF threads. D3 9
Inlet relief options Direct pressure relief vave VMD5 ( J G 3 - ) Standard setting in bar (for value see page 8) djustable spring type (, 3, 4). djustment type (G, H) djustment type G: with screw H: valve set and locked Wrench 9 4 Nm / 3 lbft Wrench 3 4 Nm / 7.7 lbft Cap code: 3CO76 llen wrench 4 max. 5.5 59.5.3.34 erformance data 4 (bar) 3 Spring nr. (green band) Spring nr. 3 (blue band) Spring nr. 4 (red band) 5 5 (US gpm) 5 5 (US gpm) 5 5 (US gpm) (psi) 4 (psi) 4 (psi) (bar) (bar) 45 3 45 3 45 ressure 3 5 ressure 3 5 ressure 3 5 4 6 Flow (l/min) 4 6 Flow (l/min) 4 6 Flow (l/min) SV: relief valve blanking plug Response time llen wrench 4 Nm / 3 lbft (% ) ressure 5% 95% 9% % bar 45 psi, RESONSE IME ime ( ) D3
Spool options ype For special requirement, spool CS code 3CU suggested for flow from 5 to 3 l/min -- 4 to 7.9 US gpm and spool CEX code 3CU3 suggested for flow up to 5 l/min -- 4 US gpm, are available. " stroke + 5.5 mm +. in LC.39 9.35.79 LC 4 5.59 ------ closed, with flow through line (LC) open - 5.5 mm stroke -. in LC erformance data 6 (l/min ) Spool metering ().. (in) 5 (US gpm) 6 (l/min ) Spool metering ().. (in) 5 (US gpm) Flow 4 F Y J 5 Qin = 45 l/min - US gpm... 3. 4. 5. 5.5 F (on ports) = 63bar / 9 psi Y (on ports) = bar / 45 psi J (on ports) = 5bar / 36 psi... 3. 4. 5. 5.5 Stroke (mm) Stroke (mm) Flow 4 J F Y 5 D3
Spool options ype LC -- closed,, flow through line (LC) open ype LC -- closed,, flow through line (LC) open ype LC closed, --, flow through line (LC) open ype H LC closed, -- partially open to tank, flow through line (LC) open D3
Spool options ype 3 " stroke + 5.5 mm +. in LC ort plugged llen wrench 6-4 Nm / 7.7 lbft LC ---- closed, flow through line (LC) open stroke - 5.5 mm -. in LC erformance data 6 (l/min ) Spool metering.. (in) 5 (US gpm) 6 (l/min) Spool metering.. (in) 5 (US gpm) Flow 4 Y Y 5 F J Qin = 45 l/min - US gpm 5 F (on ports) = 63bar / 9 psi... 3. 4. 5. 5.5 Y (on ports) = bar / 45 psi J (on ports) = 5bar / 36 psi... 3. 4. 5. 5.5 Stroke (mm) Stroke (mm) Flow 4 J F D3 3
Spool options ype 5DY It needs special body with extra machining: for information please contact Customer Service. his spool must be coupled with positioner type 3NZ. lso available spool with check valve on port; type 5WY code 3CU43. 3 llen wrench 4 LC, " stroke + 4.5 mm +.8 in Wrench 6 9,8 Nm / 7. lbft 3 7.5.85 ositioner kit 3NZ LC ------ closed flow through line (LC) open 3 Locking force: 8 N / 63 lbf ±% Unlocking force: 3 N / 67.4 lbf ±% LC, stroke - 4.5 mm -.8 in 3 LC -- (float in lock position) stroke - 9 mm -.35 in erformance data Spool metering Qin = 45 l/min - US gpm / (on ports) = bar - 45 psi.. (in) 6 (l/min ) 5 (US gpm) Flow 4 5 (bar) ressure 5 5 ressure drop in position 3 (last section) 5 5(US gpm) (psi)... 3. 4. 5. 5.5 Stroke (mm) 5 3 45 6 Flow (l/min) 4 D3
Spool options ype 5Y It needs special body with extra machining: for information please contact Customer Service. his spool must be coupled with positioner type 3QN. 3 Locking force: 37 N / 83. lbf ±% Unlocking force: 39 N / 87.7 lbf ±% LC -- (float in lock position) "" stroke + 9 mm +.35 in 3 llen wrench 4 Wrench 6 9,8 Nm / 7. lbft LC, " stroke + 4.5 mm +.8 in 3 7,5 ositioner kit 3QN Wrench 9,8 Nm / 7. lbft LC ------ closed flow through line (LC) open 3 LC, stroke - 4.5 mm -.8 in erformance data Spool metering Qin = 45 l/min - US gpm / (on ports) = bar - 45 psi 6 (l/min) Flow 4.. (in) 5 (US gpm) 5 ressione (bar) 5 5 ressure drop in position 3 (last section) 5 5(US gpm) () (psi)... 3. 4. 5. 5.5 Stroke (mm) 5 3 45 6 ortata (l/min) D3 5
Spool options ype 8 It needs special body with extra machining: for information please contact Customer Service. his spool must be coupled with positioner type 3FZ. 3 LC, " stroke + 4.5 mm +.8 in llen wrench 5 9.8 Nm / 7. lbft llen wrench 4 3 7.5.85 ositioner kit 3FZ LC ------ closed flow through line (LC) open 3 LC, stroke - 4.5 mm -.8 in 3 LC -- (regenerative) stroke - 7.5 mm -.9 in erformance data Spool metering Qin = 45 l/min - US gpm / (on ports) = bar - 45 psi 6 (l/min ) Flow 4 ().. () (in) 5 (US gpm) 5 (bar) ressure 5 5 ressure drop in positione 3 (last section) 5 5(US gpm) (psi)... 3. 4. 5. 5.5 Stroke (mm) 5 3 45 6 Flow (l/min) 6 D3
Spool options ype 8F It needs special body with extra machining: for information please contact Customer Service. " stroke + 5.5 mm +. in LC -- (regenerative) LC ------ closed, flow through line (LC) open stroke - 5.5 mm -. in LC, erformance data Spool metering Qin = 45 l/min - US gpm / (on ports) = bar - 45 psi 6 (l/min) Flow 4.. (in) 5 (US gpm) 5 (bar) ressure 5 5 ressure drop in position (last section) 5 5(US gpm) (psi)... 3. 4. 5. 5.5 Stroke (mm) 5 3 45 6 Flow (l/min) D3 7
side spool positioners With spring return in neutral position 8 kit It s supplied with standard spring type D (see force--stroke diagram) andavailable withlighter springtype C(8MC code: 5V85) or heavier type E (8ME code: 5V845). llen wrench 4 llen rench 5 9.8 Nm / 7. lbft 36.5.44 3 (N) Force Force -stroke diagram -. -... (in) (lbf) E 6 D 4 C - C - D - -4 E -6-3 -6-5 -4-3 - - 3 4 5 6 Stroke (mm) 8D kit llen wrench 4 Wrench 9 9.8 Nm / 7. lbft.47 8D kit llen wrench 4 Wrench 9 9.8 Nm / 7. lbft M8 M6 36.5.44 44.73 4 36.5.57.44 84 3.3 8 D3
side spool positioners With spring return in neutral position 8F kit llen wrench 5 9.8 Nm / 7. lbft llen wrench 4 Wrench 3 4 Nm / 7.7 lbft llen wrench 4 M8x 36.5.44 5.5.3 9 kit llen wrench 4 llen wrench 5 9.8 Nm / 7. lbft 36.5.44.. (in) 3 (lbf) (N) 6 4 - - - -4-3 -6 3 4 5 6 Stroke (mm) Force Force -stroke diagram kit llen wrench 4 llen wrench 5 9.8 Nm / 7. lbft 36.5.44 -. -. (in) 3 (lbf) (N) 6 4 - - - -4-3 -6-6 -5-4 -3 - - Stroke (mm) Force Force -stroke diagram D3 9
side spool positioners With detent 9 kit kit llen wrench 4 llen wrench 5 9.8 Nm / 7. lbft llen wrench 4 llen wrench 5 9.8 Nm / 7. lbft 45,5 45.5.79 Operating features Locking force (from pos. to )... : 5 N / 33.7 lbf ±% Unlocking force (from pos. to ). : 4 N / 3.5 lbf ±% kit 4.6 Operating features Locking force (from pos. to )... : 5 N / 33.7 lbf ±% Unlocking force (from pos. to ). : 4 N / 3.5 lbf ±% kit llen wrench 4 llen wrench 5 9.8 Nm / 7. lbft llen wrench 4 llen wrench 5 9.8 Nm / 7. lbft 36.5.44 Operating features Locking and unlocking force...... : N / 7 lbf ±% 36.5 36,5.44 Operating features Locking and unlocking force...... : N /.5 lbf ±% 5 kit 6 kit llen wrench 4 llen wrench 5 9.8 Nm / 7. lbft llen wrench 4 llen wrench 5 9.8 Nm / 7. lbft 36.5.44 Operating features Locking and unlocking force...... : N /.5 lbf ±% 36.5.44 Operating features Locking and unlocking force...... : N /.5 lbf ±% D3
side spool positioners With detent and sprimg return to neutral position from either directions 9 kit llen wrench 4 7.5.85 llen wrench 5 9.8 Nm / 7. lbft 3 (N) Force - Force -stroke diagram -. -. From position to - -4-3 From position to : -6-6 -5-4 -3 - - 3 4 5 6 Stroke (mm) Locking -unlocking area : From position to Ulocking force: N / 45 lbf ±%.. (in) (lbf) From position to 6 4 - kit llen wrench 4 7.5.85 llen wrench 5 9.8 Nm / 7. lbft 3 (N) Force - - -4-3 From position to -6-6 -5-4 -3 - - 3 4 5 6 Stroke (mm) Locking -unlocking area : : Force -stroke diagram -. -. From position to Ulocking force: N / 45 lbf ±%.. (in) (lbf) From position to 6 4 From position to - kit llen wrench 4 7.5.85 llen wrench 5 9.8 Nm / 7. lbft 3 (N) Force From position to - From position to - - -4 From position to : -6-3 -6-5 -4-3 - - 3 4 5 6 Stroke (mm) Locking -unlocking area : : Force -stroke diagram -. -. Ulocking force: N / 45 lbf ±%.. (in) (lbf) From position to 6 4 D3
side spool positioners 8MS3 kit: with centralized control for microswitch Example of a two section valve assembly Microswitch on request (see page 5) M3 n. threads 5.4.4 racket for 5MIC microswitch 58.8 8.3 Rocker arm to actuate microswitch llen wrench.5 llen wrench.5 75 Es.: SD5/--(JG3--)/8MS3L/8MS3L/E -- KM S 5 ssembling kit Nr. of working sections 5 = with bracket for M5 (I5) microswitch fixing 67 = with bracket for M67 (I67) microswitch fixing S = bracket placed on left D = bracket placed on right D3
side spool positioners 8MS3 kit: with centralized control for microswitch Other configurations llen wrench 4 llen wrench.5 8MS kit microswitch operation in position 8MS kit microswitch operation in position 58.3.9 Notch.5 mm /.6 in 9.8 Nm / 7. lbft Microswitches for 8MS kits Complete with rubber cover and mounting screws. M5 code: 5MIC M67 code: 5MIC 6.4 5.5 4..55 Dedicated bracket is needed for the assembly code: 3FL55 7.8 58..9 33 6.3.4 64.5 M3 4.83.6 3..9.5. Stroke 68.68 Operating features Max. current / voltage............. : 5 / 48 VC :.5 / 5 VDC Weather protection............... : I5 55.5.9 M4 8 4.7.6 7..7.5.6 Stroke Operating features Max. current / voltage............. : 5 / 5 VC :.5 / 3VDC Weather protection............... : I67 D3 3
side spool positioners With microswitch and spring return in neutral position 8MG3 kit 3 4.6 Microswitch kit with CKRD male connector 8MG3 kit microswitch operation in positions and Wrench 9.8 Nm / 7. lbft Wrench 4 Nm / 3 lbft llen wrench 4 Other configuration 8MG kit microswitch operation in position 66,5 llen wrench 5 9.8 Nm / 7. lbft llen wrench 4 Microswitch operating features Mechanical life........... : 5x 5 operations Electrical life (resistive load) : 5 operations - 7 / 3,5VDC : 5x 4 operations - / VDC 8MG kit microswitch operation in position Microswitches ordering codes he kit consisting of microswitch and connector, can be ordered separately (normally closed NC version is available on request). CODE DESCRIION 4MIC73 Normally open (NO) microswitch kit with CKRD male connector: needs C7 female connector 4MIC74 Normally closed (NC) microswitch kit with CKRD female connector: nedds C7 male connector For connection see page NOG. 4 D3
side spool positioners With microswitch and spring return in neutral position 8M3 kit notch.5 mm /.6 in 9.8 Nm / 7. lbft llen wrench 4 llen wrench.5 74.9 36.5.44 8EM: with electromagnetic detent With spring return in neutral position and electromagnetic detent in position. Solenoid kit with DEUSCH male connector (need connector type C..., see page NO G) Notch. mm /.47 in Wrench - 9.8 Nm / 7. lbft llen wrench 4 6 3.6 Operating features Nominal voltage............... : / 4 VDC ± % ower rating.................. : 4 W Resistance ( C)............. : 36 / 44 Ohm Min. release force.............. : 45 N Duty cycle.................... : % 88 3.46 4.37 Solenoid ordering codes With male DEUSCH connector CODE DESCRIION YSOL58465 VDC solenoid YSOL58466 4 VDC solenoid D3 5
side spool positioners 8MHE3 kit: with spring return in neutral position and spool positioning ON/OFF signal his module supplies two different ON/OFF signals, related to the direction of the spool. It has two separate contacts which can be normallyopen or normally closed. Connection DIN4365/C (needs connector type C, see page 6) Notch - Wrench 5 Wrench 9.8 Nm / 7. lbft Connector wiring osition signal 38.5.5 Operating features ower supply range : from 3 da 8 VDC Max. output current. : 5 m Weather protection. : I65 8 3.9 44.5.75 8MHE3(NC) kit 8MHE3(NO) kit 4 3 4 3 Configuration with normally closed circuit Configuration with normally open circuit View View Mobile contact Fixed contact Mobile contact Fixed contact (VDC) % Voltage 3 4 Wrench 5 9.8 Nm / 7. lbft Vedi particolare osition signal Ouput signal with NC circuit Ouput signal with NO circuit olerance range olerance range -. -... (in) (VDC) -. -... % Voltage -6-5 -4-3 - - 3 4 5 6 Stroke (mm) -6-5 -4-3 - - 3 4 5 6 Stroke (mm) 6 D3
side spool positioners 8: ON/OFF pneumatic kit Wrench 9.8 Nm / 7. lbft N /8 - nr. thread V V llen wrench 4 V 5,5 3.9 V Operating features ilot pressure................... : min. 5.5 bar / 8 psi : max. bar / 45 psi Wrench 9.8 Nm / 7. lbft 8 4.64 llen wrench 4 8E3: ON/OFF electro -pneumatic kit Wrench 4 9.8 Nm / 7. lbft g9 43 57.69.4 Scheme V V Connector C inclded code: X (see page 6) 3.5 4.47 V V Scheme ISO 9 4.65 8 Ø.3 V V llen wrench 4 neumatic solenoid valves codes (with connector) CODE X4 X44 Wrench 3 4 Nm / 7.7 lbft 9 4.68 Wrench 9 DESCRIION Nominal voltage VDC Nominal voltage 4VDC llen wrench 4 - Special wrench - 9.8 Nm / 7. lbft Operating features ilot pressure.................. : 6 bar / 87 psi : (max. bar / 45 psi) Solenoid operating features Nominal voltage tolerance......... : ±% ower rating.................... : 8 W Duty Cycle...................... : % D3 7
side spool positioners 8ED3: ON/OFF electro -hydraulic kit With external pilot and drain. Coil 4 39 5.47 59.65.3 6.6 Nm 4.9 lbft Connection ISO44 (needs C connector, see page 6) L V Scheme 5.4 33 / Collector Wrench 6 4.57 33 5.4 llen wrench 4 - llen wrench 4 - Collector kit for external pilot and drain Wrench 4 Nm / 7.7 lbft Solenoid valve: wrench 4-9.8 Nm / 7. lbft Wrench 4 Nm / 7.7 lbft Special wrench 9.8 Nm / 7. lbft SE 6 V Scheme ISO 9 V L Operating features ilot pressure.................. : min. bar / 45 psi : max. 5 bar / 75 psi Max. backpressure on drain L..... : 5 bar / 36 psi Solenoid operating features Nominal voltage tolerance........ : ±% ower rating................... : W Duty cycle..................... : % Ordering codes CODE SEJ83 X435 X4354 DESCRIION 3 -way solenoid valve VDC coil 4VDC coil L V L bar 9 psi 49.5 5.89 Collector 75 Ordering codes (UN -UNF thread) Ex: SD5/--(JG3--)/8ED3L/8ED3L/E--SE -KES -4VDC YE CODE DESCRIION KES 5KES7 Kit for section KES 5KES7 Kit for sections KE3S 5KE3S7 Kit for 3 sections KE4S 5KE4S7 Kit for 4 sections KE5S 5KE5S7 Kit for 5 sections KE6S 5KE6S7 Kit for 6 sections KE7S 5KE7S7 kit for 7 sections 8 D3
side spool positioners 8ED3: ON/OFF electro -hydraulic kit Collector kit with pilot and drain lines he kit consists of a collector with VR pressure reducing valve and relative pipes. llen wrench 6 4 Nm / 7.7 lbft 8 36. 5.35 Collector Wrench 9 4 Nm / 7.7 lbft VR VR Code: S88VL Drain 49.5 5.89 Wrench 7 Inlet line Wrench 4 4 Nm / 3 lbft VRC Wrench 4 4 Nm / 7.7 lbft 35.38 VRC back pressure valve (not included) 75 Ex: SD5/--(JG3--)/8ED3L/8ED3L/VRC -SE - KER3-4VDC VR valve operating features Outlet pressure.................. : bar / 9 psi Max. flow....................... : 8 l/min Filtering........................ : 8 µ Ordering codes (UN -UNF thread) YE CODE DESCRIION KER3 5KER37 Kit for section KER3 5KER37 Kit for sections KE3R3 5KE3R37 Kit for 3 sections KE4R3 5KE4R37 Kit for 4 sections KE5R3 5KE5R37 Kit for 5 sections KE6R3 5KE6R37 Kit for 6 sections VRC valve : code X36 Valve assembled on flow through passage provides pilot pressure to the actuator..79 Wrench 4 Nm / 3 lbft Wrench 4 Nm / 7.7 lbft 4 (bar) 3 ressure ressure drop 4 8 (US gpm) (psi) 4 5 3 45 Flow (l/min) D3 9
side options Lever controls L type lluminium with protection boot lever pivot box; it can be rotated 8 (execution L8). (**) (*) Vertical handlever assembly Horizontal handlever assembly M8 Execution L8 4. 5.96.79 53.7. 65.5.58.79 44.73 llen wrench 4 4.6 9..5 NOE (*) - With spool type 5DY (see page 4) (**) -- With spool type 5Y (see page 5) LM type LF type M M8 M M8 54.3 7.5.8 llen wrench.5 4.5.96 4.5.96.79.79 53.7. 65.5.58 44 llen wrench 4.79 44.73 max66.6 Wrench 3 4 Nm / 7.7 lbft llen wrench 4-3 D3
side options Special lever controls Safety levers with lock in neutral complete with handlever; lift handlever knob to operate. LE type 4.5 5.5.96.79.3 5 Stroke to ulocking Locking bush Wrench 3 4 Nm / 7.7 lbft 36.5 9.3 LU type.79 44.73 llen wrench 4 vailable as LU(R5) configuration, with lenght L = 5 mm / 5.9 in and red knob: code 5LEV85..79 M8 9 8.6 65.56.83 Standard black knob Wrench 3 4 Nm / 7.7 lbft 53.7..47 Stroke to ulocking Locking bush 5.8.8 llen wrench 4 D3 3
side options Controls prearrangement SL type SL type SLC type llen wrench 4 llen wrench 8 3 Nm /. lbft.87 9.35 8.3 68.5.7 llen wrench 4-9H8.35 +.866 5.59 Mechanical control with dust--proof plate. rotection cap usable with pneumatic, electro--pneumatic, and electro--hydraulic spool positioners. Q cable remote control kit Waterproof cap prearranged for remote control with flexible cable. llen wrench 4 - Wrench - 9.8 Nm / 7. lbft Wrench 4-4 Nm / 7.7 lbft Example of cable control 8 3.9 Flexible cable NOE - For more information about remote cable control, require appropriate documentation. Q kit SCF3 remote control CD flexible cables SD5/ directional control valve without lever boxes 3 D3
Kit comandi lato LC mechanical joystick for two sections control Execution LC4 st section spool nd section spool ivot Wrench 3 4 Nm / 7.7 lbft Wrench llen wrench 5 9.8 Nm / 7. lbft llen wrench 4 - llen wrench 4 - Wrench 3-4 Nm / 7.7 lbft Wrench 3-4 Nm / 7.7 lbft Wrench - 9.8 Nm / 7. lbft NOE - he handlever must be ordered separately (see page 9). Dimensions and movement scheme Execution LC pivot placed down on the left Execution LC pivot placed down on the right st section axis nd section axis spool axis - - - - 7.83 - - - M 7.39.6 -.5.85 76.99 36.4 Execution LC3 pivot placed above to the left Exection LC4 pivot placed above on the right - - - - 36.4 - - - - NOE - Don t use with spool type 5DY..5.6 D3 33
Complete controls 8IM: proportional hydraulic control code 5IDR57 It can be used with standard spools and body (body kit without seals on spool). Coupling suggested with type CS spool (see page ). V V llen wrench 5 9.8 Nm / 7. lbft V 8. 38 SE6.5 V llen wrench 4 Spool 5.5 97 7.76 4.65 (bar) ilot pressure 5 5 6 ilot pressure - stroke diagram Max. pilot pressure 5 bar -- 7 psi ort ort -. -... (in) -5.5 5.5-6 -4-4 6 Stroke (mm) (psi) Spool overlap area Metering area 34 D3
Complete controls 8IM: proportional hydraulic control code 5IDR5 Connection example Hydraulic pilot control valve series SV with curve type 6 3 (bar) Curve 6...3 (in) (psi) 4 ilot pressure 4 6.5 3 3 6 8.5 9 Stroke (mm) 4 3 V V V V V V V V 75 Ex: SD5/--(JG3--5)/CS8IM/CS8IM/E--SE+ SV--S/W--6x4 D3 35
Complete controls 8ESN solenoid control Direct control by double solenoid with spring return to neutral position, available with emergency manual override. It s necessary special spool and standard body (body kit without spool seals). Due to the large dimension, it s not possible to assembly more than one control consecutively, except SD5/ - and SD5/3 - that have special bodies with bigger centre--to--centre. Description example: SD5 / - (JG3 -) / 8ESN LES / E - SE - 4VDC.. 3. 4. 5. 3. 5. 4.. LES. CE. ody kit * YE CODE DESCRIION SD5/ - 5KC93 section, standard body SD5/ -S 5KC33 sections, special body SD5/3 -S 5KC436 3 sections, special body. Spool options YE CODE DESCRIION (ES) 3CU36 Double acting, 3 positions, with and closed in neutral position (ES) 3CU536 Double acting, 3 positions, with and open to tank in neutral position 3. Connection kit YE CODE DESCRIION 8ESN 5V89 For solenoid joint, with spring return in neutral position 4. side options YE CODE DESCRIION LES 5LEV54 Safety lever pivot box for manual operation CE 5CO5 Endcap 5. Solenoid YE CODE DESCRIION.5VDC XSOL343 Nominal voltage.5vdc VDC XSOL343 Nominal voltage VDC 4VDC XSOL344 Nominal voltage 4VDC 9VDC XSOL349 Nominal voltage 9VDC; (for VC supply) NOE (*) - Codes are referred to UN- UNF threads. 36 D3
Complete controls 8ESN solenoid control Electric wiring example 8ESNLES kit with safety lever pivot box 3 8ESNCE kit with encadp Connector -- o battery + Operating features Internal leakage () ( p = bar - 45 psi = 4 C - 4 F)................ Solenoid operating features Nominal voltage tolerance......... : ±% ower rating.................... : 65 W Coil insulance................... : class H Duty cycle...................... : % : cm 3 /min -.6 in 3 /min Manual operation: lift the bush to lever unlocking LES Connection ISO44 (needs C3 connector for VDC supply or C5 connector for VC supply; see page 6) llen wrench 4 Wrench 4 9.8 Nm / 7. lbft W W 3 llen wrench 68.5.7 CE Wrench 4 4 Nm / 7.7 lbft 7.5 6.79 llen wrench 4 9.8 Nm / 7. lbft Spool: wrench 3 3.6 llen wrench 4 D3 37
Complete controls 8ES solenoid control Solenoid direct control with spring return to neutral position. It needs special spools and standard body (body kit without seals on spool). Description example: SD5 / - (JG3 -) / 8ES3 / E - SE - 4VDC.. 3. 4. 4. I 3. 8ES3 8ES. 8ES3 8ES 3. 8ES 3.. 3. 8ES 4.. ody kit * YE CODE DESCRIION SD5/ - 5KC93 section SD5/ - 5KC3 sections SD5/3-5KC43 3 sections SD5/4-5KC73 4 sections SD5/5-5KC33 5 sections SD5/6-5KC353 6 sections SD5/7-5KC3E3 7 sections. Spool options YE CODE DESCRIION (ES) 3CU Double acting, 3 positions, with and closed in neutral position (ES) 3CU5 Double acting, 3 positions, with and open to tank in neutral position NOE (*) - Codes are referred to UN- UNF threads. 3. Control kit YE CODE DESCRIION 8ES 5V84 Single acting, with spring return to neutral position 8ES 5V84 Single acting, with spring return to neutral position 8ES3 5V85 Double acting, with spring return to neutral position 4. Coil YE CODE DESCRIION.5VDC 4SOL5 Nominal voltage.5vdc VDC 4SOL5 Nominal voltage VDC 4VDC 4SOL54 Nominal voltage 4VDC I and ports plugs * YE CODE DESCRIION SE6 3X873 For single acting controls type 8ES and 8ES 38 D3
Complete control 8ES solenoid control Electric wiring example 8ES3 kit double acting 8ES kit single acting on Connector Connector -- o battery + 8ES kit single acting on Operating features Internal leakage () ( p = bar - 45 psi = 4 C - 4 F)................ Coil operating features Nominal voltage tolerance......... : ±% ower rating.................... : 36 W Coil insulance................... : class H Duty cycle...................... : % : cm 3 /min -.6 in 3 /min Operating condition diagram 4 8 (US gpm) 4 (bar) (psi) 3 45 ressure Operation area 5 3 45 Flow (l/min) 3 5 7 Nm 5. lbft Wrench 4 Nm / 7.7 lbft llen wrench 4 3.5.93 Conn. Conn. Connection ISO44 (needs C connector, see page. 6) Spool 93.8 3.69 Wrench 3 4 Nm / 7.7 lbft Emergency manual override D3 39
Outlet port options It s possible to have open center, closed center and power beyond. Unloader valves are available: these valves need special bodies with appropriate cavity on lateral outlet port, the tank connection must be on top. E: open center (standard) See page 6 E: with power beyond EK: closed center Wrench 7-4 Nm / 3 lbft C SE8 llen wrench 8-4 Nm / 3 lbft 3.5.93 4.6 C 75 75 Ex: SD5/--(KG3--)/8L/8L/E -SE Ex: SD5/--(KG3--)/8L/8L/EK L: hydraulic pilot unloader valve For safety reasons it s provided with pilot port plugged. 3. SE6 X Wrench 4 Nm / 7.7 lbft (bar) ressure 9 6 3 ressure drop curve 4 8 (US gpm) Wrench 4 4 Nm / 3 lbft 3 4 45 Operating features Flow (l/min) Internal leakage................. : cm 3 /min a bar :.6 in 3 /min at 45 psi (psi) 5 5 Ex.: SD5/--(JG3--)/8L/8L/E--L -SE X 4 D3
Outlet port options EL: electric control unloader valve Wrench 7 4 Nm / 3 lbft 3 4.84 Wrench 4 4 Nm / 3 lbft Wrench 3 4 Nm / 3 lbft ush and twist push -button for manual override ISO44 connection (needs C connector, see page 6) Ex.: SD5/--(JG3--)/8L/8L/E--EL -VDC Operating features Internal leakage (excited position).. : 75 cm 3 /min at bar : 4.6 in 3 /min at 45 psi Solenoid operating features Nominal voltage................. : VDC 4 VDC Nominal voltage tolerance......... : ±% ower rating.................... : 9 W Nominal current.................. :,58,8 Resistance..................... : 7,6 Ω 9,5 Ω Coil insulation................... : Class F Duty cycle...................... : % Coils ordering codes CODE X43 X434 DESCRIION Nominal voltage VDC Nominal voltage 4VDC 5 (bar) ressure 5 5 ressure drop curve 4 8 (US gpm) (psi) 3 3 4 45 Flow (l/min) L: unloader valve prearrangement llen wrench 6 4 Nm / 7.7 lbft Ex.: SD5/--(JG3--)/8L/8L/E--L D3 4
Service valves. ll service valves need special body: contact Customer Service. S 3. 4. VS.. VSC(JG...) VSC Kit VS Kit VD VD 6. VD 5. VM(...) VM Kit VM VM(...) VD3 VM 4 D3
Service valves. Relief valve page 44 YE CODE DESCRIION VS(G3-) 3XCR553 Range 4 to bar / 58 to 9 psi standard setting bar / 45 psi VS 3X493 Valve blanking plug 4. ilot check valves page 47 Fitted with mounting block YE CODE DESCRIION Directv type 6* lock with valve on port 6* lock with valve on port 3 6* lock with valves on ports and XCR65 Single valve With pre -opening S 635* lock with valve on port S 635* lock with valve on port S3 635* lock with valves on ports and S XCR65 Single valve X673 and S valves blanking plug. Flange mounted relief valve page 45 YE CODE DESCRIION VSC(JG-6) 5KI54 Range 4 to 8 bar / 58 to 5 psi standard setting 6 bar / 87 psi VSC(JG3-) 5KI543 Range 63 to bar / 9 to 9 psi standard setting bar / 45 psi VSC(JG4-) 5KI544 Range 6 to 5 bar / 3 to 36 psi standard setting bar / 9 psi VSC X638 Valve blanking plug Kit VS 5CO4 Mounting block kit 3. ntishock valves page 46 Cross return type, fitted with mounting block YE CODE DESCRIION (G3-) 67* lock with valve on port (G3-) 67* lock with valve on port 3(G3-) 6* lock with valves on ports and (G-6) 5CR Single valve: range 4 to bar / 58 to 45 psi,standard setting 6 bar / 87 psi (G3-) 5CR3 Single valve: range 8 to bar / 5 to 9 psi, standard setting bar / 45 psi (G4-) 5CR3 Single valve: range 8 to 35 bar / 6 to 46 psi, standard setting bar / 9 psi X5643 Valve blanking plug (for configuration, ) 5. nti -schock+anti -cavitation valve page 49 Flange mounted type with fixed setting (setting is referred to Q = l/min -.64 US gpm flow) YE CODE DESCRIION VM(5) 5KI365 Setting 5 bar / 7 psi VM(6) 5KI366 Setting 6 bar / 87 psi VM(7) 5KI367 Setting 7 bar / psi VM(8) 5KI368 Setting 8 bar / 5 psi VM(9) 5KI369 Setting 9 bar / 3 psi VM() 5KI36 Setting bar / 45 psi VM(5) 5KI365 Setting 5 bar / 8 psi VM(4) 5KI364 Setting 4 bar / 5 psi VM(6) 5KI366 Setting 6 bar / 3 psi VM(75) 5KI3675 Setting 75 bar / 55 psi VM(9) 5KI369 Setting 9 bar / 75 psi VM() 5KI36 Setting bar / 35 psi VM(3) 5KI363 Setting 3 bar / 335 psi VM(5) 5KI365 Setting 5 bar / 36 psi VM(6) 5KI366 Setting 6 bar / 375 psi VM(8) 5KI368 Setting 8 bar / 45 psi VM(3) 5KI363 Setting 3 bar / 435 psi VM X34 Valve blanking plug Kit VM 5CO8 Mounting block kit 6. Flow control valves page 5 Flow control on every section; with auxiliary inlet YE CODE DESCRIION VD S Fine regulation from 3 to 3 l/min VD S636 s VD, one turn with detent VD3 S VDC proportional solenoid valve Kit VD 5CO85* Mounting block kit NOE -- Valve setting at points - -3 are referred to l/min -.64 US gpm flow. NOE -- (*) Codes are referred to UN- UNF threads. D3 43
Services valves VS relief valve It s suggested for flow up to 5 l/min -- 6.6 US gpm, and it s mounted on parallel body to limitate the pressure, at lower value than main relief valve (min. gap bar -- 9 psi ), on downstream section. It s in parallel with flow trough and it works only with single operation. VS5 ( G 3 - ) djustment type (G, H) ressure setting in bar (standard bar / 45 psi) 75 45 djustment type G: with screw H: valve set and locked Wrench 9.8 Nm / 7. lbft Wrench 7 4 Nm / 7.7 lbft Wrench 9 4 Nm / 7.7 lbft llen wrench 3 Max.3.5.8 erformance data 4 (bar) 3 Spring nr. 3 (blue band) 4 6 (US gpm) (psi) 45 (% ) 5% Response time ressure 3 5 ressure 95% 9% bar 45 psi 3 Flow (l/min) %,8 RESONSE IME ime ( ) VS: valve blanking plug llen wrench 6 4 Nm / 3 lbft 4.6 44 D3
\ Service valves VSC relief valve It s flange mounted on parallel body on the opposite side of working ports, the function to limit the pressure, at lower value than main relief valve (min. gap bar -- 9 psi) on downstream sections. It s in parallel with flow through line and it works only with single operation. It needs a dedicated body with extra machining: for production requirements, the block () isflanged () before thefinal honingof spool hole, while the valve (3) is mounted during final assembling phase. For information contact Customer Service. 3 VSC ( J G 3 - ) Standard setting in bar (for value see page 43) djustable spring type (, 3, 4). djustment type (G, H) LC 3.5.53 3.6 75 max. 5.5 54.5.3.5 llen wrench 4 7.5.3 45 Ex.: SD5/--(JG3--)/8L/VSC(JG3 -)/8L/E NOE - For valve performance see page. D3 45
Service valves anti -shock valves with cross return Cast iron block with antishock valves. ( D 3 - ) - SE Spring type (, 3, 4). djustment with blind nut (D). mounted on port. rmounted on port. 3 mounted on ports and. Standard setting in bar (for value see page 43) 3 45 45 45 45 configuration Example of pressure on port and port to tank 3 configuration Example of pressure on port and port to tank llen wrench 8 4 Nm / 3 lbft Wrench 7 4 Nm / 3 lbft llen wrench 5 Wrench 4 Nm / 7.7 lbft erformance data 4 (bar) 3 Spring nr. (green band) Spring nr. 3 (blue band) 5 5 (US gpm) 5 5 (US gpm) 4 (psi) (bar) (psi) 45 3 45 ressure 3 5 ressure 3 5 4 6 Flow (l/min) 4 6 Flow (l/min) 4 (bar) 3 Spring nr. 4 (red band) 5 5 (US gpm) (psi) 45 (% ) 5% ime response ressure 3 5 ressure 95% 9% bar 75 psi 4 6 Flow (l/min) %, IME RESONSE ime ( ) 46 D3
Service valves, S pilot check valves Cast iron block with pilot check valves. S - SE mounted on port. mounted on port. 3 mounted on ports and. S direct type with pre -opening 3 S S S3 configuration Example of pressure on port and port to tank 3 configuration Example of pressure on port and port to tank Wrench 7 4 Nm / 3 lbft Wrench 7 4 Nm / 3 lbft Wrench 9 4 Nm / 3 lbft Example of pressure on port and port to tank Example of pressure on port and port to tank erformance data 4 (bar) ressure 3 valve pressure drop 5 5 (US gpm) 5 5 (US gpm) 4 (psi) ilot ratio (bar) (psi) 45 ype With Main 3 45 pre--opening 4 6 Flow (l/min) 3 5 S : 6 / : 5.3 : 3. ressure S valve pressure drop 4 6 Flow (l/min) 3 5 D3 47
Service valves antishock valves with cross return 3 configuration valve block 36.4 3 configuration valve block 3.8 9.75 58.8.5.85 56.5. 4.55 8 9 8 8.5..35..73 6.5.46.6 M5 6.5.65 6..83 6.5.65 88.79 3.46 8 5.4 5 9.97.75 6.36 4.3.56 3.66 93 = = 97 = 3.8 =.6 = 4.79 = 3 configuration 3, S3 configuration 3 3 37 7 5.5.9.8.46.6. L special lever box code: 5LEV55 Standard lever box Example of extra machining on directional valve body Milled surface with fixing threaded holes 7.6 37.5.48.39 3.5 48 D3
Service valves VM anti -shock and anti -cavitation hey are flange mounted on the opposite side of working ports, connected in parallel with and ports and with outlet on port. It needs a dedicated body with extra machining: for production requirements, the block () isflanged () before thefinal honingof spool hole, while the valve (3) is mounted during final assembling phase. For information contact Customer Service. 3 VM () VM VM VM3 Valve setting in bar mounted on port mounted on port 3 mounted on ports and 45 45 45 45 VM configuration 35 (bar) 3 5 ressure -flow diagram 4 8 (US gpm) (psi) 45 4.5.63 8.5. 75.8.95 llen wrench 4 Nm / 7.7 lbft 4.5.57 llen wrench 4 llen wrench 6 4 Nm / 7.7 lbft ressure 3 5 5 5 3 4 45 Flow (l/min) D3 49
Service valves VD flow control valves lock with pressure compensated 3--way flow control valve, to be flange mounted on body with parallel circuit. he cavity is oriented toward lever side. he flow is regulated on every working section while the exceeding flow goes to tank: max. regulated flow 3 l/min -- 7.9 US gpm (with inlet on port). It needs a dedicated body with extra machining: for production requirements, the block () isflanged () before thefinal honingof spool hole, while the valve (3) is mounted during final assembling phase. For information contact Customer Service. 3 Manual control VD: continuous fine regulation Hydraulic circuit 33.5.3 3.5.53.5 77 44.45 3.3.73 Ex.: SD5/--(JG3--)VD/8L/8L/E--SE 75 VD: one turn with detent handknob regulated R C 94.5 3.7 Ex.: SD5/--(JG3--)VD/8L/8L/E--SE 5 D3
Service valves VD flow control valves VD3 with proportional solenoid control ISO44 connection (needs C connector, see page. 6) Hydraulic circuit 33.5.4 3.5.53.5 77 94.5.45 3.3 3.7 Ex.: SD5/--(JG3--)VD3/8L/8L/E 75 C R VD3 proprtional solenoid flow control valve connection It s shows a configuration with push--button panel type U. For information contact Customer Service. Emergency push -button SO otentiometer for valve adjustment Solenoid operating feautures Nominal voltage......... : VDC ower rating............ : 8 W Duty cycle.............. : % ISO44 connector ush -button panel type: U//SC o battery erformance data 4 (l/min) riority flow 3 ressure -flow diagram Qin = 45 l/min 3 (psi) (US gpm) 9 6 3 Flow regulation diagram Qin = 45 l/min ( US gpm) - = bar (45 psi) (l/min) 4 riority flow 3,3,6,9, Current () F Y J (US gpm) 9 6 3 F Y J VD flow control valve VD flow control valve VD3 flow control valve 3 9 5 7 ressure (bar),,5,,5,,5 (n.of turn) 3 6 9 5 8 (n.of clicks) D3 5
5 D3
Other executions SD5/-N................................................... page 54 It s available only with one working section and it can be used in hydrauliccircuits where power beyond doesn t required. SD5/-D................................................... page 55 It s available only with one working section and it can be used in hydrauliccircuits where power beyond is required. SD5-S: with series circuit............................ page 56 vailablefromto6 sections, it canbe usedin systemswich onedownstream section from series connection must work with upstream ones at the same time. It s not available the power beyond circuit. On the same body are possible more than one connection. SD5-S: with tandem circuit......................... pag. 58 vailable from to 6 sections, for security reasons it can be used in systems which is required to prohibit engagement of downstream sections from tandem connection when the upstream sections are working. On the same body are possible more than one connection. D3 53
/ -N Dimensional data 5.5 4.5 4 73.55.87 63.5 3.5 45..77 8.5.33 86 7.3 46 45.5 34.8.79.34 M8.5 5.45. 8 3.9 3 4.6.79 osition 5 os. 5 osition 4.5 3 7.96.8.6 4.5.96 9 3.54 Standard threads ORS S (ISO8/) UN -UNF (ISO 96 -) MERIC (ISO 6) Inlet G 3/8 3/4--6 UNF-- (SE 8) M8x.5 orts and G 3/8 9/6--8 UNF-- (SE 6) M8x.5 Outlet G 3/8 3/4--6 UNF-- (SE 8) M8x.5 Hydraulic circuit erformance data 75 Ex.: SD5/--N(JG3--)/8L--SE Code: 8 5 (bar) ressure 5 ressure drop curve 5 5 (US gpm) () 5 3 45 6 Flow () (l/min) (psi) 5 5 54 D3
/ -D Dimensional data 4. 3 73.5.87 63.5 3.5. 45.77 8.5.33 86 7.3 46 45.5 34.8.79.34 3.5 3 7.93.8.6 M8.5 5.45. 8 3.9 3.79 4.6 4.5.96 9 3.54 osition 5 os. 5 osition Standard threads ORS S (ISO8/) UN -UNF (ISO 96 -) MERIC (ISO 6) Inlet and power beyond C G 3/8 3/4--6 UNF-- (SE 8) M8x.5 orts and G 3/8 9/6--8 UNF-- (SE 6) M8x.5 Outlet G 3/8 3/4--6 UNF-- (SE 8) M8x.5 Hydraulic circuit erformance data 75 Ex.: SD5/--D(JG3--)/8L--SE Code: 63 C 5 5 (US gpm) (bar) 5 (psi) 5 () C 5 5 () 5 3 45 6 resure ressure drop curve Flow (l/min) D3 55
-S Dimensional data.5.49 E F 4.5.96 63.5 3.5 45..77 45.5.79 5. 86 7.3.5.45 34.34 8 3.9 3 4.6 8.5.33 osition 45.77 M 8.79 5 5 os. 3 3 37 7.9.8.46.6 9 3.54 osition YE E F Weight E F Weight YE mm in mm in kg lb mm in mm in kg lb SD5/ -S 37.5 5.4 4.33 5..4 SD5/5 -S 48.5 9.78 8.7..3 SD5/3 -S 74.5 6.87 47 5.79 6.9 5. SD5/6 -S 85.5. 58..7 5.8 SD5/4 -S.5 8.33 84 7.4 8. 7.9 Standard threads ORS S (ISO8/) UN -UNF (ISO 96 -) MERIC (ISO 6) Inlet G 3/8 3/4--6 UNF-- (SE 8) M8x.5 orts and G 3/8 9/6--8 UNF-- (SE 6) M8x.5 Outlet G / 3/4--6 UNF-- (SE 8) Mx.5 56 D3
-S Hydraulic circuit he description of SD5 valve with series circuit is marked with letter S and one figure wich indicate the downstream sections from series connection. 3 3 4 4 vailable body kits 75 CODE DESCRIION 5KC574 SD5/ -S 5KC57 SD5/3 -S 5KCD7 SD5/3 -S+ 5KC87 SD5/4 -S 5KCE7 SD5/4 -S++ 5KC373 SD5/5 -S 5KC77 SD5/5 -S+++ 5KC37 SD5/5 -S+ 5KC367 SD5/6 -S Ex.: SD5/4--S(JG3--)/8L/8L/8L/8L--SE Code: 48 Include boby, seals and load check valves. erformance data 4 (bar) ressure 3 ressure drop ressure drop () 5 5 (US gpm) 5 5 (US gpm) 4 (psi) (bar) (psi) 6 sections 45 3 6 ( 6 ) 45 4 sectionis sections 3 ( ) 3 5 5 ressure 5 3 45 6 Flow (l/min) 5 3 45 6 Flow (l/min) 4 (bar) 3 ressure drop ressure drop () between port () before series connection and port () after 5 5 (US gpm) 5 5 (US gpm) 4 ( ) (psi) (bar) (psi) 45 3 45 ressure 6 ( 6 ) 3 5 ressure 3 5 5 3 45 6 Flow (l/min) 5 3 45 6 Flow (l/min) D3 57
-S Dimensional data,5.49 E F ower beyond.8 4.5.96 63.5 3.5 45..77 45.5.79 5..5.45 86 7.3 8 3.9 3 4.6 34.34 8.5.33 osizione 45.77 M 8.79 5 5 os. 3 3 37 7.9.8.46.6 9 3.54 osizione YE E F Weight E F Weight YE mm in mm in kg lb mm in mm in kg lb SD5/ -S 37.5 5.4 4.33 4.8.6 SD5/5 -S4 48.5 9.78 8.7..5 SD5/3 -S 74.5 6.87 47 5.79 6.7 4.8 SD5/6 -S5 85.5. 58..3 4.9 SD5/4 -S3.5 8.33 84 7.4 8. 7.6 SD5/7 -S6 3.5 3. 95.6.7 8 Standard thread ORS S (ISO8/) UN -UNF (ISO 96 -) MERIC (ISO 6) Inlet and power beyond C G 3/8 3/4--6 UNF-- (SE 8) M8x.5 orts and G 3/8 9/6--8 UNF-- (SE 6) M8x.5 Outlet G 3/8 3/4--6 UNF-- (SE 8) M8x.5 58 D3
-S Hydraulic circuit he description of SD5 valve with tandem circuit is marked with letters S and one figure wich indicate the downstream sections from tandem connection. vailable body kits 75 3 3 4 4 Ex.: SD5/4--S3(JG3--)/8L/8L/8L/8L/E--SE Code: 49 CODE 5KC87 5KCG7 5KC37 5KCH7 5KCI7 5KC97 5KC3D7 5KC347 5KC337 5KC397 5KC3Y7 5KC377 5KC3J7 5KC3G7 5KC3L7 5KC3F7 DESCRIION SD5/ -S SD5/3 -S SD5/4 -S SD5/4 -S+ SD5/4 -S+ SD5/4 -S3 SD5/5 -S+ SD5/5 -S3+ SD5/5 -S4 SD5/6 -S3+ SD5/6 -S3+ SD5/6 -S5 SD5/7 -S3+ SD5/7 -S4 SD5/7 -S5+ SD5/7 -S6 Include boby, seals and load check valve. erformance data 4 (bar) ressure 3 ressure drop ressure drop () 5 5 (US gpm) 5 5 (US gpm) 4 (psi) (bar) (psi) 6 sections 45 4 sections 3 sections 5 ressure 3 6 ( 6 ) ( ) 45 3 5 5 3 45 6 Flow (l/min) 5 3 45 6 Flow (l/min) 4 (bar) 3 ressure drop () 5 5 (US gpm) (psi) ( ) 45 ressure 6 ( 6 ) 3 5 5 3 45 6 Flow (l/min) D3 59
Installation and maintenance he SD5 valve is assembled and tested as per the technical specification of this catalog. efore the final installation on your equipment, follow the below recommendations: -- the valve can be assembled in any position, in order to prevent body deformation and spool sticking mount the product on a flat surface; -- in order to prevent the possibility of water entering the lever box and spool control kit, do not use high pressure wash down directly on the valve; -- prior to painting, ensure plastic port plugs are tightly in place. C ower beyond configuration Fitting tightening torque - Nm / lbft HREDS YE and C ports and ports port S (ISO 8/) G 3/8 G 3/8 G 3/8 (G /*) With O--Ring seal 35 / 5.8 35 / 5.8 35 / 5.8(5 / 36.9*) With copper washer 4 / 9.5 4 / 9.5 4 / 9.5 (5 / 36.9*) With steel and rubber washer 3 /. 3 /. 3 /. (5 / 36.9*) UN--UNF (ISO 96--) 3/4--6 UNF-- (SE 8) 9/6--8 UNF-- (SE 6) 3/4--6 UNF-- (SE 8) With O--Ring seal 4 / 9.5 3 /. 3 /. MERIC (ISO 6) M8 x.5 M8 x.5 M8 x.5 (Mx.5*) With O--Ring seal 35 / 5.8 35 / 5.8 35 / 5.8 (5*) With copper washer 4 / 9.5 4 / 9.5 4 / 9.5 (5*) With steel and rubber washer 4 / 9.5 4 / 9.5 4 / 9.5 (5*) (*) -- Only for series circuit. NOE -- hese torque are recommended. ssembly tightening torque depends on many factors, including lubrication, coating and surface finish. he manufacturer shall be consulted. 6 D3
Installation and maintenance O -Ring seal 5,88x,6 - code: 4GU596 Note In case of assistance follw this assembling procedure - fit the O -Rimg seal in seat on lever side; - fit the spool from the opposite side and till it is possible to fit the other O -Ring seal; - position the spool in center. ositioner kit Load check valve ody Sealing edge Lever pivot box Main relief valve Spool Normally spools are interchangeable. Verify the smoothness during the assembly NOE -- ll articulated parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI Malfunction Cause Remedy External leakage pivot box lever or control kit side. Excessive internal leakage on and ports. Dropping load during transition while raising Worn spool seal due to mechanical actuation or high back pressure. Increase clearance between spools and body due to high wear. High leakage on the load check valve. Locate the leakage and replace the seal. Check back pressure level. Replace the directional control valve and check the oil contamination level. Remove the load check valve and clean the seat, verifing it s not dented. Inability to build pressure on and ressure relief valve blocked open. Remove and clean or replace the valve. ports. Low pump pressure and flow. Check the pump and circuit. D3 6