INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM P/N 08E60-SLN-100 2007 FIT AII 31719 Issue Date MAR 2006 PARTS LIST Fuse label B Keyless entry harness User s information Fuse label A 5 Wire ties TOOLS AND SUPPLIES REQUIRED 8 mm and 10 mm Combination wrenches Ratchet 10 mm Socket Isopropyl alcohol Shop towel Illustration of Keyless Entry System Installed on the Vehicle Fuse (20A) Ground bolt 2 Remote controls KEYLESS UNIT Keyless unit KEYLESS ENTRY 5920131K 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31719 (0603) 08E65-SLN-1000-91 1 of 5
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. 3. Remove the driver s dashboard under cover: Turn the knob clockwise. Release the clip and one pin. 4. Pull away the weatherstrip from around the driver s kick panel. Remove the kick panel (two clips). WEATHERSTRIP CLIPS (2) DRIVER S KICK PANEL 5914020K 5. Remove the fuse box cover: Turn the knob counterclockwise. Release the five clips and three retaining tabs. PIN CLIP CLIPS (5) DRIVER S DASHBOARD UNDER COVER KNOB 5914010K COVER RETAINING TABS (3) KNOB 5914030K 2 of 5 AII 31719 (0603) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
6. Attach one OPTION 2A of the fuse label A to each keyless entry harness fuse case. 8. Plug the keyless entry harness 5-pin connector into the fuse box slot as shown. CASE 7-PIN (with cover) (with urethane foam) LABEL A OPTION 2A 5920122K 7. Plug the keyless entry harness 5-pin connector into the keyless unit, then slide the keyless unit onto the bracket on the instrument panel bracket. BRACKET KEYLESS UNIT (green) 5920071K 9. Secure the keyless entry harness 7-pin connector with cover to the vehicle harness using one wire tie. 10. Route the keyless entry harness 5-pin connector wrapped with urethane foam to the back of the fuse box. NOTE: If the fuse box 5-pin connector is already used by fog light switch harness: Locate the 5-pin connector black-taped to the fog light switch harness, and remove the dummy connector from the 5-pin connector. Plug the keyless entry harness 5-pin connector into the fog light switch harness 5-pin connector (black-taped). 5920091K BLACK TAPE FOG LIGHT SWITCH DUMMY 5N03201H (Discard.) 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31719 (0603) 3 of 5
11. Behind the fuse box, remove the blue tape that secures the vehicle 5-pin connector. 15. Install the 20A fuse into the number 20 slot in the fuse box. (BACK) FRONT VIEW LOCATION 20 20A BLUE TAPE WIRE TIE (with urethane foam) 5920082K 12. Plug the vehicle 5-pin connector into the keyless entry harness 5-pin connector, then secure the keyless entry harness to the vehicle harness with one wire tie. 13. Remove and discard the bolt from the bottom of the hood opener lever. Using the ground bolt from the kit, secure the keyless entry harness ground terminal as shown. 16. Secure the keyless entry harness to the vehicle harness with two wire ties. 17. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle fuse label on the back of the fuse box cover. COVER 5920110K HOOD OPENER LEVER LABEL B BOLT (Discard.) GROUND TERMINAL GROUND BOLT 5920100K 14. Secure the keyless entry harness to the vehicle harness using one wire tie. LABEL (Thoroughly clean with isopropyl alcohol.) ADHESIVE BACKING 5920800K 18. Remove the adhesive backing from the fuse label B, and then attach the fuse label B over the existing vehicle fuse label as shown. 4 of 5 AII 31719 (0603) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
19. Check that all wire harnesses and cables are routed properly and all connectors are plugged in. 20. Reinstall all removed parts. 21. Reconnect the negative cable to the battery. 22. Enter the customer s radio anti-theft code, if applicable, and reset the radio station presets. 23. Set the clock. 24. Check operation of the keyless entry according to the User s Information. NOTE: When the battery is disconnected, the driver s window AUTO function is disabled. Start the engine. Push down on the driver s window switch until the window is fully open. Pull up on the driver s window switch to close the window completely, then hold the switch for 2 seconds or more. Lower and raise the driver s window to check operation of the driver s window AUTO function. 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31719 (0603) 5 of 5