INSTALL GUIDE OEM-GM(RS)-GM-[OL-RS-GM]-EN DOCUMENT NUMBER 0 REVISION DATE 0 FIRMWARE OEM-GM(RS)-GM-[OL-RS-GM] HARDWARE OL-RS-GM ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately) Audio & Electronics
VEHICLE LIST - OF DOC.:#0 0 FEATURES MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS X LOCK START/STANDALONE MOD. ARM OEM ALARM DISARM OEM ALARM DOOR LOCK* CHEVROLET DOOR UNLOCK* PONTIAC SATURN PRIORITY UNLOCK* TRUNK/HATCH RELEASE* PUDDLE LIGHT CTRL** DOOR STATUS OUTPUT TRUNK STATUS OUTPUT TACHOMETER OUTPUT PARKING LIGHT CTRL IGNITION CTRL BRAKE PEDAL STATUS OUTPUT RAP SHUTDOWN CTRL Cobalt STD key AT (with PK) 0-0 HHR STD key AT (with PK) 0- Malibu STD key AT (with PK) 0- Malibu Hybrid STD key AT (with PK) 0- Malibu MAXX STD key AT (with PK) 0-0 G STD key AT 0-0 Pursuit / G STD key AT (with PK) 0-0 Solstice STD key AT (with PK) 0-0 Aura / Hybrid STD key AT (with PK) 0-0 Sky STD key AT (with PK) 0-0 *Doorlocks and trunk release features on the module will not operate on vehicles that are not equipped with OEM keyless entry. **If puddle light function is active in vehicle settings.
BOX CONTENTS - OF DOC.: #0 0 BOX CONTENTS MODULE T-HARNESS 0 PIN MS VS BLUE BLACK 0 0 A B LED LED G F E PROGRAMMING BUTTON BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK MS T-HARNESS JS JS VS VS VS PIN AFTERMARKET HOOD SWITCH AND CABLE BLACK 0 C D 0 WHITE T-HARNESS JS VS WARNING STICKER VS PIN JS WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE
TYPE - WIRE CHART - OF DOC.: #0 0 MAKE CHEVROLET MODEL PONTIAC YEAR WIRE DESCRIPTION NAME COLOR TYPE SATURN POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Malibu STD key AT (with PK) Malibu Hybrid STD key AT (with PK) Malibu MAXX STD key AT (with PK) G STD key AT (with PK) Aura / Hybrid STD key AT (with PK) 0-0- 0-0 0-0 0-0 Brake ~ ~ ~ ~ ~ ~ ~ ~ Keyless Data ~ ~ ~ ~ ~ ~ ~ ~ Doorlock C Gray pin White (MUX) BCM ~ Horn C White pin Tan (-) BCM ~ Parking Light C White pin 0 Brown/White (-) BCM ~ Trunk C Gray pin Brown/White (-) BCM ~ Driver Door Pin C Gray pin Gray/Black (-) BCM ~ Brake ~ ~ ~ ~ ~ ~ ~ ~ Keyless Data ~ ~ ~ ~ ~ ~ ~ ~ Doorlock C Gray pin White (MUX) BCM ~ Horn C White pin Tan (-) BCM ~ Parking Light C White pin 0 Brown/White (-) BCM ~ Trunk C Gray pin Brown/White (-) BCM ~ Driver Door Pin C Gray pin Gray/Black (-) BCM ~ Brake ~ ~ ~ ~ ~ ~ ~ ~ Keyless Data ~ ~ ~ ~ ~ ~ ~ ~ Doorlock C Gray pin White (MUX) BCM ~ Horn C White pin Tan (-) BCM ~ Parking Light C White pin 0 Brown/White (-) BCM ~ Trunk C Gray pin Brown/White (-) BCM ~ Driver Door Pin C Gray pin Gray/Black (-) BCM ~
TYPE - WIRING DIAGRAM - OF DOC.: #0 0 MODULE VEHICLE IGNITION SWITCH A B C G F E D RF PORT/WEBLINK PORT TELEMATIC PORT VS VS A A IGNITION IGNITION HARNESS A MS JS JS JS VS B -WAY PK B VS B -WAY PK HARNESS 0 0 MS A A B B C D 0 0 0 BROWN/BLACK - PARKING LIGHT (-) OUTPUT 0 GRAY - RAP SHUTDOWN (-) OUTPUT 0 PURPLE/GREEN - LOCK (-) OUTPUT 0 BLUE/GREEN - TRUNK (-) OUTPUT GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOCK (-) OUTPUT 0 GRAY/BLACK - BRAKE (+) INPUT 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH WHITE - KEYLESS DATA OUTPUT 00 OHM 00 TO 00 MODELS WITH OEM KEYLESS ONLY OPTIONAL WITHOUT OEM KEYLESS ONLY 00 TO 00 MODELS ONLY KEYLESS DATA - PARKING LIGHT (-) - 0 HORN (-) - TRUNK RELEASE (-) - DOORLOCK (MUX) - DRIVER DOOR PIN (-) - BRAKE (+) - C C 0 0 0 0 0 0 0 0 0 0 0 0 0 0 BCM C AFTERMARKET HOOD SWITCH (-) C
TYPE - WIRE CHART - OF PAGE OF 0 DOC.: #0 0 MAKE MODEL YEAR WIRE DESCRIPTION NAME COLOR TYPE POSITION WIRE COLOR POLARITY CHEVROLET MODULE LOCATION COMPONENT LOCATOR Brake ~ ~ ~ ~ ~ ~ ~ ~ PONTIAC SATURN Cobalt STD key AT (with PK) Pursuit/G STD key AT (with PK) Sky STD key AT (with PK) 0-0 0-0 0-0 Keyless Data ~ ~ ~ ~ ~ ~ ~ ~ Doorlock C Gray pin 0 White (MUX) BCM ~ Horn C White pin Tan (-) BCM ~ Parking Light C White pin 0 Brown/White (-) BCM ~ Trunk C White pin 0 Tan (-) BCM ~ Driver Door Pin C Gray pin Gray/Black (-) BCM ~ Brake ~ ~ ~ ~ ~ ~ ~ ~ Keyless Data ~ ~ ~ ~ ~ ~ ~ ~ Doorlock C Gray pin 0 White (MUX) BCM ~ Horn C White pin Tan (-) BCM ~ Parking Light C White pin 0 Brown/White (-) BCM ~ Trunk C White pin 0 Tan (-) BCM ~ Driver Door Pin C Gray pin Gray/Black (-) BCM ~ Brake ~ ~ ~ ~ ~ ~ ~ ~ Keyless Data ~ ~ ~ ~ ~ ~ ~ ~ Doorlock C Gray pin 0 White (MUX) BCM ~ Horn C White pin Tan (-) BCM ~ Parking Light C White pin 0 Brown/White (-) BCM ~ Trunk C White pin 0 Tan (-) BCM ~ Driver Door Pin C Gray pin Gray/Black (-) BCM ~
TYPE - WIRING DIAGRAM - OF DOC.: #0 0 MODULE VEHICLE IGNITION SWITCH A B C G F E D RF PORT/WEBLINK PORT TELEMATIC PORT VS VS A A IGNITION IGNITION HARNESS A MS JS JS JS VS B -WAY PK B VS B -WAY PK HARNESS 0 0 MS A A B B C D 0 0 BROWN/BLACK - PARKING LIGHT (-) OUTPUT 0 GRAY - RAP SHUTDOWN (-) OUTPUT 0 PURPLE/GREEN - LOCK (-) OUTPUT 0 BLUE/GREEN - TRUNK (-) OUTPUT GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOCK (-) OUTPUT WHITE - KEYLESS DATA OUTPUT 00 TO 00 MODELS WITH OEM KEYLESS ONLY OPTIONAL 00 TO 00 MODELS ONLY WITHOUT OEM KEYLESS ONLY KEYLESS DATA - PARKING LIGHT (-) - 0 HORN (-) - BRAKE (+) - TRUNK RELEASE (-) - 0 DOORLOCK (MUX) - 0 C C 0 0 0 0 0 0 0 BCM 0 0 GRAY/BLACK - BRAKE (+) INPUT 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH 00 OHM DRIVER DOOR PIN (-) - 0 0 0 0 0 0 0 C AFTERMARKET HOOD SWITCH (-) C
TYPE - WIRE CHART - OF DOC.: #0 0 MAKE MODEL YEAR WIRE DESCRIPTION NAME CHEVROLET COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Brake ~ ~ ~ ~ ~ ~ ~ ~ HHR STD key AT (with PK) 0- Keyless Data ~ ~ ~ ~ ~ ~ ~ ~ Doorlock C Gray pin 0 White or White/Black (MUX) BCM ~ Horn C White pin Tan (-) BCM ~ Parking Light C White pin 0 Brown/White (-) BCM ~ Trunk C Gray pin White/Black (-) BCM ~ Driver Door Pin C Gray pin Gray/Black (-) BCM ~
TYPE - WIRING DIAGRAM - OF DOC.: #0 0 MODULE VEHICLE IGNITION SWITCH A B C G F E D RF PORT/WEBLINK PORT TELEMATIC PORT VS VS A A IGNITION IGNITION HARNESS A MS JS JS JS VS B -WAY PK B VS B -WAY PK HARNESS 0 0 MS A A B B C D 0 0 0 BROWN/BLACK - PARKING LIGHT (-) OUTPUT 0 GRAY - RAP SHUTDOWN (-) OUTPUT 0 PURPLE/GREEN - LOCK (-) OUTPUT 0 BLUE/GREEN - TRUNK (-) OUTPUT GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOCK (-) OUTPUT 0 GRAY/BLACK - BRAKE (+) INPUT 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH WHITE - KEYLESS DATA OUTPUT 00 OHM 00 TO 00 MODELS WITH OEM KEYLESS ONLY OPTIONAL 00 TO 00 MODELS ONLY WITHOUT OEM KEYLESS ONLY KEYLESS DATA - PARKING LIGHT (-) - 0 HORN (-) - BRAKE (+) - TRUNK RELEASE (-) - DOORLOCK (MUX) - 0 DRIVER DOOR PIN (-) - C C 0 0 0 0 0 0 0 0 0 0 0 0 0 0 BCM C AFTERMARKET HOOD SWITCH (-) C
TYPE - WIRE CHART - OF DOC.: #0 0 MAKE MODEL YEAR WIRE DESCRIPTION NAME COLOR PONTIAC TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Brake ~ ~ ~ ~ ~ ~ ~ ~ Keyless Data ~ ~ ~ ~ ~ ~ ~ ~ Solstice STD key AT (with PK) 0-0 Doorlock C Gray pin 0 White (MUX) BCM ~ Horn C White pin Tan (-) BCM ~ Parking Light C White pin 0 Brown/White (-) BCM ~ Trunk C White pin 0 Tan (-) BCM ~ Driver Door Pin C Gray pin Gray/Black (-) BCM ~
TYPE - WIRING DIAGRAM - OF DOC.: #0 0 MODULE VEHICLE IGNITION SWITCH A B C G F E D RF PORT/WEBLINK PORT TELEMATIC PORT VS VS A A IGNITION IGNITION HARNESS A MS JS JS JS VS B -WAY PK B VS B -WAY PK HARNESS 0 0 MS A A B B C D 0 0 BROWN/BLACK - PARKING LIGHT (-) OUTPUT 0 GRAY - RAP SHUTDOWN (-) OUTPUT 0 PURPLE/GREEN - LOCK (-) OUTPUT 0 BLUE/GREEN - TRUNK (-) OUTPUT GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOCK (-) OUTPUT WHITE - KEYLESS DATA OUTPUT 00 TO 00 MODELS WITH OEM KEYLESS ONLY OPTIONAL WITHOUT OEM KEYLESS ONLY KEYLESS DATA - PARKING LIGHT (-) - 0 HORN (-) - TRUNK RELEASE (-) - 0 DOORLOCK (MUX) - 0 C C 0 0 0 0 0 0 0 BCM 0 0 GRAY/BLACK - BRAKE (+) INPUT 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH 00 OHM 00 TO 00 MODELS ONLY BRAKE (+) - DRIVER DOOR PIN (-) - 0 0 0 0 0 0 0 C AFTERMARKET HOOD SWITCH (-) C
MODULE PROGRAMMING PROCEDURE - OF DOC.: #0 0 0 Close driver door. 0 ACC ON START Release key from Start position and return to ON position. 0 Re-open driver door to wake up data bus. 0 Wait, LED will turn solid GREEN for seconds. 0 ACC ON START Insert key into ignition. Wait seconds. 0 ACC ON START Turn key to position. 0 ACC ON START Turn key to ACC position. Wait seconds. 0 Module Programming Procedure completed. 0 ACC ON START Turn key to ON position. Wait seconds. 0 ACC ON START Turn key to START position and hold for seconds.
VALET MODE PROGRAMMING PROCEDURE - OF DOC.: #0 0 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to. 0 Time restriction. Complete next step within seconds. 0 ACC ON START Cycle ignition ON five times [x /ON] rapidly. ENGINE START STOP 0 Wait, LED will turn solid RED for seconds. 0 ACC ON START Set ignition to position. ENGINE START STOP 0 Valet Mode Programming Procedure completed.
MODULE NAVIGATION PROCEDURE - OF DOC.: #0 0 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. >> Module must be programmed to the vehicle. 0 [Y] IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. [Y] LED will flash RED as many times as the current option number continuously. >> Use the Module Navigation Chart on the next page. 0 TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. 0 ACC ON START Set ignition to position. 0 [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn. ENGINE START STOP 0 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 0 [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. 0 [X] IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 0 To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery.
MODULE NAVIGATION CHART - OF DOC.: #0 0 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 CONFIGURATION 0 DISARM/UNLOCK BEFORE START 0 0 ON 0 RELOCK AFTER START 0 0 ON 0 RELOCK AFTER SHUTDOWN 0 0 ON 0 FORCE UNLOCK ALL ON FIRST PRESS 0 0 ON 0 TAKEOVER 0 ENABLE 0 DISABLE* 0 N/A 0 N/A 0 DISABLE 0 FACTORY KEYLESS RS SEQUENCE 0 N/A 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 0 MIN 0 0 MIN 0 MODULE RUN TIME 0 MIN 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 SEC 0 0 SEC 0 0 SEC 0 WAIT TO START DELAY 0 0 SEC 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0 N/A 0 N/A N/A 0 N/A N/A 0 N/A N/A 0 N/A
MODULE NAVIGATION CHART - OF DOC.: #0 0 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS *Vehicle will shutdown when a door is opened. 0 DOUBLE LOCK HORN EVENT TRIGGER 0 LOCK + UNLOCK 0 LOCK + UNLOCK + START 0 CONFIGURATION 0 DOUBLE LOCK + START 0 0 msec HORN CHIRPS WIDTH 0 msec 0 0 msec 0-0 Technical Support only 0 N/A 0 N/A
REMOTE STARTER ERROR CODES - OF DOC.: #0 0 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 0 Hood is open. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 0 Glow plug timeout error. 0 RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. 0 N/A N/A N/A N/A N/A N/A CAN communication failure during RS sequence.
MODULE DIAGNOSTICS - OF DOC.: #0 0 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.
MODULE RESET PROCEDURE - OF DOC.: #0 0 0 Disconnect all connectors from module except the BLACK 0-PIN connector. 0 Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. 0 Repeat programming procedure. 0 PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed.
INSTALLATION CHECKLIST - OF DOC.: #0 0 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Exit vehicle. Installation checklist completed.