Contents Introduction Augers Inclinometer Casing Subs & Pipe Wrenches Samplers Hoisting, Lowering, Hammers & Rockbits Corebarrels, Drill Rods & Casings Diamond Products Thin Wall Bits & Saw Blades Water Swivels & Pumps Conventional & Wireline Packers Grouters Bentonite Products Well Protection Bailers & Water Level Indicators PVC Stainless Dimensions & Conversions Terms 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
1 Boart Longyear s Quick Reference Mini Catalogue was developed specifically for the Geoenvironmental drilling company. It contains only the most commonly used products for Geo-environmental drilling. Boart Longyear has a substantially broader product line than what is published in the mini catalogue so if you do not find the product you require call your nearest Boart Longyear office for additional information and literature. 1.1
Augers 2
HOLLOW STEM AUGERS, KEYED DESIGN 2 1. Drive Cap 2. Nut & Bolt for Rod Cap Adapter 3. Lock Bolt 4. Replacement Bushing 5. Replacement Drive Key 6. Rod Cap Adapter 7. Drill Rod 8. Hollow Stem Auger 9. Pilot Bit Connector 10. Cutter Head - 5T Type 11. Knock-Out Wrench, Bullet Cutters 12. Cutter Head - Bullet Type 13. Cutter Head - Spade/Bullet Type 14. Cutter Head - Blade Type 15. Cutter Head - Spade Type 16. Cutter Head - Blade/Bullet Type 17. Pilot Bit - Bullet Type 18. Pilot Bit - Apex Type 19. Pilot Bit - Step Type Boart Longyear Augers Tool joints are manufactured from 4130 heat treated steel 5 axis CNC machining assures precision fit and dimensions Hard faced flighting Heat treated bushing and auger bolts Carbide enhanced cutterheads 2 key, 3 key, octagonal drive augers Standard duty, heavy duty, extra heavy duty 2.1
Auger Tools 2 Key Item No. 2 Key Augers with Continuous Hard-Faced Flighting DA-295 DA-300 DA-310 DA-320 Description 2 1/4 in. I.D. x 5 5/8 in. O.D. x 5 ft., Single Bolt Connection 3 1/4 in. I.D. x 6 5/8 in. O.D. x 5 ft., Single Bolt Connection 4 1/4 in. I.D. x 7 5/8 in. O.D. x 5 ft., Double Bolt Connection 6 1/4 in. I.D. x 9 5/8 in. O.D. x 5 ft., Double Bolt Connection *Double bolt available upon request 2 5T Cutter Heads DA-436 DA-442 DA-452 DA-467 Spade/Bullet Cutter Heads DA-43504 DA-440 DA-450 DA-465 Bullet Cutter Heads DA-435 DA-441 DA-451 DA-466 Replacement Items DA-650 DA-660 DA-662 DA-665 DA-670 Accessory Items DA-700 DA-280 DA-281 DA-225 Wooden Auger Plugs DA-624 DA-625 DA-626 DA-627 2 1/4 in., 2 Key, 5T Tooth Type 3 1/4 in., 2 Key, 5T Tooth Type 4 1/4 in., 2 Key, 5T Tooth Type 6 1/4 in., 2 Key, 5T Tooth Type 2 1/4 in., 2 Key, Spade/Bullet Type 3 1/4 in., 2 Key, Spade/Bullet Type 4 1/4 in., 2 Key, Spade/Bullet Type 6 1/4 in., 2 Key, Spade/Bullet Type 2 1/4 in., 2 Key, Bullet Type 3 1/4 in., 2 Key, Bullet Type 4 1/4 in., 2 Key, Bullet Type 6 1/4 in., 2 Key, Bullet Type 5T Tooth, Forged Shank Spade Cutter Bullet Cutter Blade Cutter Replacement Lock Bolt Auger Hoisting Hook Adjustable Extension Rod (30 in. - 50 in.), 1 5/8 in. Hex Adjustable Extension Rod (30 in. - 50 in.), 2 in. Hex Pointed Hammer 2 1/4 in. Wooden Auger Plug 3 1/4 in. Wooden Auger Plug 4 1/4 in. Wooden Auger Plug 6 1/4 in. Wooden Auger Plug *Thick Plugs 8 1/4-10 1/4-12 1/4 available upon request Flex Center Plugs DA-634 2 1/4 in. Flex Plug DA-635 3 1/4 in. Flex Plug DA-636 4 1/4 in. Flex Plug DA-637 6 1/4 in. Flex Plug 2.2
Auger Tools 3 Key 2 Item No. Description 3 Key Augers with Continuous Hard-Faced Flighting DA-305 3 1/4 in. I.D. x 6 5/8 in. O.D. x 5 ft., Single Bolt Connection DA-315 4 1/4 in. I.D. x 7 5/8 in. O.D. x 5 ft., Double Bolt Connection DA-325 6 5/8 in. I.D. x 10 in. O.D. x 5 ft., Double Bolt Connection 5T Cutter Heads DA-447 DA-462 DA-472 Spade/Bullet Cutter Heads DA-44604 DA-46104 DA-47104 Bullet Cutter Heads DA-446 DA-461 DA-471 Replacement Items 3 1/4 in., 3 Key, 5T Tooth Type 4 1/4 in., 3 Key, 5T Tooth Type 6 in., 3 Key, 5T Tooth Type 3 1/4 in., 3 Key, Spade/Bullet Type 4 1/4 in., 3 Key, Spade/Bullet Type 6 in., 3 Key, Spade/Bullet Type 3 1/4 in., 3 Key, Bullet Type 4 1/4 in., 3 Key, Bullet Type 6 in., 3 Key, Bullet Type DA-650 5T Tooth, Forged Shank DA-660 Spade Cutter DA-662 Bullet Cutter DA-670 Replacement Lock Bolt DA-665 Blade Cutter Accessory Items DA-700 DA-280 DA-281 DA-225 Wooden Auger Plugs DA-625 DA-626 DA-628 Flex Center Plugs DA-634 DA-635 DA-636 Auger Hoisting Hook Adjustable Extension Rod (30 in. - 50 in.), 1 5/8 in. Hex Adjustable Extension Rod (30 in. - 50 in.), 2 in. Hex Pointed Hammer 3 1/4 in. Wooden Auger Plug 4 1/4 in. Wooden Auger Plug 6 5/8 in. Wooden Auger Plug *Thick Plugs 8 1/4-10 1/4-12 1/4 available upon request 2 1/4 in. Flex Plug 3 1/4 in. Flex Plug 4 1/4 in. Flex Plug 2.3
Auger Tools Heavy Duty Item No. Description Heavy Duty Augers with Continuous Hard-Faced Flighting 4581502 4 1/4 in. x 5 ft., 2 Key, Heavy Duty Auger 4002649 4 1/4 in. x 5 ft., 2 Key, Extra Heavy Duty Auger 4000497 4 1/4 in. x 5 ft., Heavy Duty Octagonal Auger 2 HDPE Auger Plugs MON-1828 3 1/4 Beveled Auger Plug MON-1830 4 1/4 Beveled Auger Plug MON-1835 4 3/8 Beveled Auger Plug MON-1850 6 1/4 Beveled Auger Plug MON-1863 6 5/8 Beveled Auger Plug MON-1865 8 1/4 Beveled Auger Plug MON-1870 10 1/4 Beveled Auger Plug Lipped Design Auger Plugs MON-1840 4 1/4 Lipped Auger Plug MON-1860 6 1/4 Lipped Auger Plug MON-1880 10 1/4 Lipped Auger Plug MON-1890 12 1/4 Lipped Auger Plug 2.4
Solid Stem Flight Augers 2 Item No. Description 4.5 in. Flight Augers DA-100 5 ft., 1 1/8 in. Hex, Hard Surfaced DA-110 5 ft., 1 5/8 in. Hex, Hard Surfaced DA-136 Fishtail Blade Bit DA-138 Fishtail Carbide Blade Bit DA-164 1 1/8 in. Hex Drive Lug for Fishtail Bit DA-168 1 5/8 in. Hex Drive Lug for Fishtail Bit DA-176 Bolt, 5/16 in. x 1 1/2 in. (included with Fishtail Bit) DA-178 Nut, 5/16 in. (included with Fishtail Bit) DA-192 5T Tooth Bit, 1 1/8 in. Hex DA-194 5T Tooth Bit, 1 5/8 in. Hex 4002583 4 in. HD/Concrete Cutter Bit, 1 5/8 in. Shank DA-216 Drive Pin, 1 1/8 in. Hex DA-218 Drive Pin, 1 5/8 in. Hex DA-230 Recovery Tool for 1 1/8 in. (Pig Tail) DA-231 Recovery Tool for 1 5/8 in. (Pig Tail) DA-245 Auger Fork for 1 1/8 in. Hex DA-246 Auger Fork for 1 5/8 in. Hex DA-248 Hoisting Bail, 1 1/8 in. Hex DA-249 Hoisting Bail, 1 5/8 in. Hex DA-255 Repair Connector, 1 1/8 in. Shank DA-256 Repair Connector, 1 1/8 in. Socket DA-257 Repair Connector, 1 5/8 in. Shank DA-258 Repair Connector, 1 5/8 in. Socket DA-240 Hex Adaptor, 1 5/8 in. Shank to 1 1/8 in. Socket 351830 HD Concrete Cutter 05508 4.5 in. Stinger Bit, 1 5/8 in. Hex 6 in. Flight Augers DA-120 5 ft., 1 5/8 in. Hex, Hard Surfaced DA-142 Fishtail Blade Bit DA-144 Fishtail Carbide Blade Bit DA-170 1 5/8 in. Drive Lug for Fishtail Bit DA-180 Bolt, 3/8 in. (included with Fishtail Bit) DA-182 Nut, 3/8 in. (included with Fishtail Bit) DA-196 5T Tooth Bit, 1 5/8 Hex 4000620 6 in. HD/Concrete Cutter Bit, 1 5/8 in. Shank 4000721 7 in. HD/Concrete Cutter Bit, 1 5/8 in. Shank 202327 9 in. HD/Concrete Cutter Bit, 1 5/8 in. Shank DA-218 Drive Pin, 1 5/8 in. Hex DA-232 Recovery Tool, 1 5/8 in. Hex (Pig Tail) DA-246 Auger Fork 351830 HD Concrete Cutter 2.5 05516 6.0 in. Stinger Bit, 1 5/8 in. Hex Flight Auger
Solid Stem Flight Augers 2 Two-piece Fishtail Head with Carbide Tipped Cast Steel Blade for Clays, Sands and Gravels Stinger Bit Self-centering one-piece cast steel construction. Smooth contoured shape permits free flow of material to auger flight. Interchangeable with two piece bit. Works well in clay, loam, soft shale, sand and gravels. Shank Bit Auger Hoisting Assembly Auger Holder 5T Tooth Bit General Purpose Heavy Duty Replacement Cutter Adapter Hex Shank to Hex Box HD Bit (Heavy Duty) A tough, multi-purpose auger head. Uses replaceable coneshaped carbide insert bits. Recommended for soft shales, sandstones and limestone formations as well as concrete. NOTE: Bits are furnished with lock rings installed. Drill head O.D. is approximately 10% larger than corresponding auger flight O.D. Optional, available on request. Drive Pin Repair Shank Repair Socket 2.6
Hand Auger Assembly 3 1/4 in. 2 The unique cylindrical Hand Auger is ideal for augering shallow holes in fine grained soils. It requires negligible force to advance the hole because the blade diameter exceeds the bucket diameter. Little effort is required to turn the hand auger to produce a 4 inch diameter hole. Standard construction for the bucket is a heavy-guage, heat-treated, plated carbon steel. The blades are hard surfaced to resist abrasion. A stainless steel Hand Auger is available for environmental sampling needs. A special windowed bucket is available to facilitate soil removal when used in sticky clays. Extensions are 3/4 inch diameter by 3-foot long and use a threadless design to avoid the need for wrenches. Quick connect pins are used to join the tee handle, extensions and bucket. A Hand Auger assembly set consists of one auger head, one tee handle and one extension. Purchase additional extensions for desired depth capacity. *Other sizes available on request. Item No. Description Standard Hand Auger S-110 Standard Hand Auger Assembly Replacement Parts S-11010 3 1/4 in. Auger Head w/ Connector, Ship Wt. 3 lbs. S-11020 Tee Handle, Ship Wt. 1 lb. S-11030 36 in. Extension w/ Connector, Ship Wt. 2 lbs. S-11040 3 1/4 in. Auger Head w/ Connector, Ship Wt. 3 lbs. Accessories S-11050 3 1/4 in. Windowed Auger Head, Ship Wt. 3 lbs. Stainless Steel Hand Auger S-111 Stainless Steel Hand Auger Assembly Replacement Parts S-11110 Stainless Steel 3 1/4 in. Auger Head w/ Connector, Ship Wt. 3 lbs. S-11120 Stainless Steel Tee Handle, Ship Wt. 1 lb. S-11130 Stainless Steel 36 in. Extension w/ Connector, Ship Wt. 2 lbs. S-11140 Stainless Steel Replacement Connector (bolt and wing nut) Accessories S-11150 Stainless Steel 3 1/4 in. Windowed Auger Head, Ship Wt. 3 lbs. 2.7
Inclinometer Casing 3
Inclinometer Casing Slope Indicator 3 QC Casing This high-strength casing provides snap-together convenience and strong, flush joints. Integral couplings are self-aligned and have O-ring seals to prevent entry of grout. Guide grooves are machine broached for excellent control of spiral and groove profile. Specifications: 85 mm/3.34 in. QC Casing OD/ID: 85/75 mm (3.34/2.82 in.) Load Rating: 635 kg (1400 lb.) Collapse Rating: 12.4 bar (180 psi) Temp Rating: -29 to 82 C (-20 to 190 F) Spiral: < 0.33 per 3m (10 ) 70 mm/2.75 in. QC Casing OD/ID: 70/60 mm (2.75/2.32 in.) Load Rating: 635 kg (1400 lb.) Collapse Rating: 6.5 bar (240 psi) Temp Rating: -29 to 82 C (-20 to 190 F) Spiral: < 0.33 per 3m (10ft) Item No. Description Packaging QC 2.75 in. Inclinometer Guide Casing SI51150210 Section, 10 ft x 2.75 in 8 per box SI51150211 Section, 5 ft x 2.75 in 8 per box SI51150230 End Cap Bottom 2.75 in 1 SI51101500 End Cap Top 2.75 in 1 Accessories QC 3.75 in. Inclinometer Guide Casing SI51150310 Section, 10 ft x 3.34 in 6 per box SI51150311 Section, 5 ft x 3.34 in 6 per box SI51150330 End Cap Bottom 3.34 in 1 SI51100500 End Cap Top 3.34 in 1 3.1
Subs & Pipe Wrenches 4
Subs Box to Box Sub Box to Pin Sub Pin to Pin Sub 4 Item No. Box to Box Subs Description 08543 N4 Box - AW Box 08544 NW R/B - AW R/B 54998 AW R/B - N3 ACME Box 200664 AW Box - AWJ Box 200665 AWJ Box - N3 Box 200666 AWJ R/B - N4 R/B 55006 AWJ R/B - 2 3/8 API Box 54441 NWJ R/B - 2 3/8 API Reg. Box 200430 NWJ R/B - 3 1/2 API Box 200673 NW R/B - 3 1/2 API Reg. Box Box to Pin Subs 17638 AW R/B - AW R/P 54398 AW R/B - AWJ R/P 16138 AW R/B - NW R/P 25328 AW R/B - NQ R/P 29031 AW Box 1 1/4 7 Pin Thread 30418 AW R/B - NW CSG/P 200221 NWJ R/B - AWJ R/P 54438 NWJ R/B - AW R/P 54407 NWJ R/B - HW CSG/P 16155 NW Box - AW Pin 55000 NW R/B - AWJ R/P 54417 NW R/B - NWJ R/P 30181 NW R/B - HW CSG/P Pin to Pin Subs 08521 AW R/P - NW R/P 54842 AW R/P - AWJ R/P 15630 AW Rod Coupling *Other Subs Available on Request 4.1
Wrenches and Spare Parts Rigid Item No. Rigid Item No. Description Wrenches and Spare Parts 14942 31025 Pipe Wrench, 18 in. 14945 31030 Pipe Wrench, 24 in. 14948 31035 Pipe Wrench, 36 in. 14951 31040 Pipe Wrench, 48 in. 200553 31045 Pipe Wrench, 60 in. 200554 31095 Aluminum Pipe Wrench, 14 in. 200555 31100 Aluminum Pipe Wrench, 18 in. 200556 31105 Aluminum Pipe Wrench, 24 in. 200557 31110 Aluminum Pipe Wrench, 36 in. 200558 31115 Aluminum Pipe Wrench, 48 in. 200559 31330 Chain Wrench, 36 in. 200560 31385 Wrench, Como. Lever Pipe 14944 31675 Jaw, 18 in. Hook 14943 31675 Jaw, 18 in. Heel C/W Pin 200561 31680 Coil and Spring, 18 in. 200562 31685 Wrench Nut, 18 in. 14950 31720 Jaw, 36 in. Hook 14949 31725 Jaw, 36 in. Heel C/W Pin 200565 31730 Coil and Spring, 36 in. 200566 31735 Wrench Nut, 36 in. 14953 31745 Jaw, 48 in. Hook 14952 31750 Jaw, 48 in. Heel C/W Pin 200567 31755 Coil and Spring, 48 in. 200568 31760 Wrench Nut, 48 in. 200569 31770 Jaw, 60 in. Hook 200570 31775 Jaw, 60 in. Heel C/W Pin 200571 31780 Coil and Spring, 60 in. 200572 31785 Wrench Nut, 60 in. 200573 32845 Heavy Duty Pipe Cutter Pipe Wrench 4 4.2
THIS PAGE INTENTIONALLY LEFT BLANK
Samplers 5
Thin Wall (Shelby) Tube 5 The Thin Wall or Shelby Tube Sampler is designed to take undisturbed samples in cohesive type clays and soils. The sampler consists of a head assembly, ball check and cap screws for securing the sampler tube. The sampler tube consists of a head assembly, ball check and cap screws for securing the sampler tube. The sampler is pressed and retracted by hydraulic force into the undisturbed clay or soils. The tube is then removed from the sampler head and the sample is retained in the tube and transported to the laboratory. The thin wall sample tubes are made available in either steel, galvanized steel or brass in varying lengths. The procedure for obtaining undisturbed samples is outlined under ASTM Standard Procedures. NOTE: If your environmental needs require, the thin wall sample tubes are available in stainless steel. Item No. Description Shelby Tube Heads DS-500 2 in. O.D. Head Assembly with Screws, AW Box DS-501 2 in. O.D. Head Assembly with Screws, AWJ Box DS-505 3 in. O.D. Head Assembly with Screws, AW Box DS-506 3 in. O.D. Head Assembly with Screws, AWJ Box DS-512 3 in. O.D. Head Assembly with Screws, NW Box DS-520 2 in. O.D. Cap Screw (4 required) DS-521 3 in. O.D. Cap Screw (4 equired) Galvanized Shelby Tubes DS-550 2 in. O.D. x 30 in. Galvanized Shelby Tube DS-551 3 in. O.D. x 30 in. Galvanized Shelby Tube DS-552 3 in. O.D. x 36 in. Galvanized Shelby Tube Shelby Tube Caps DS-630 3 in. Plastic Cap DS-631 3 in. Vinyl Cap DS-633 2 in. Vinyl Cap 5.1
The Lynac Sampler is a heavy duty split tube sampler that is widely used in the geotechnical/environmental drilling industry. This sampler is adapted for severe service under hard driving conditions. The sampling shoe is heat treated and coarse threads in the sampler head speed disassembly and assembly. The head of the assembly comes with a ball check feature that helps prevent losing a sample by washing out during withdrawal from a test boring. The heat treated shoe is recessed to allow the use of a basket retainer or trap valve. Liners for the split tubes are also available for specific sampling needs. Lynac Samplers are available in either an 18 or 24 length and the split tubes can be heat treated for the 2 OD size. 5 NOTE: This heavy-duty Lynac Sampler is recommended for Standard Penetration Tests for geotechnical drilling. NOTE: The Nordic Sampler has A4TPI shoe for easier use. Item No. Description Split Spoon Samplers DS-120 DS-122 DS-130 DS-131 DS-310 DS-311 DS-260 2 in. O.D. x 18 in. Lynac Sampler with AW Box 2 in. O.D. x 24 in. Lynac Sampler with AWJ Box 2 in. O.D. x 24 in. Lynac Sampler with AW Box 2 in. O.D. x 24 in. Lynac Sampler with AWJ Box 2 in. O.D. x 24 in. Nordic Sampler with AW Box 2 in. O.D. x 24 in. Nordic Sampler with AWJ Box 2 in. O.D. x 24 in. Stainless steel Sampler with AW Box Split Spoon Replacement Parts DS-315 DS-135 DS-140 DS-143 DS-401 DS-402 DS-405 Plastic Retainers DS-412 DS-414 2 in. O.D. x 24 in. Nordic Split Tube Only 2 in. O.D. x 24 in. Lynac Split Tube Only AW Split Spoon Head, 2 in. O.D. AWJ Split Spoon Head, 2 in. O.D. Lynac Open Shoe, Blunt, 2 in. O.D. Lynac Open Shoe, ASTM, 2 in. O.D. Nordic Open Shoe, 2 in. O.D. 2 in. Heavy Duty Retainer, Orange 2 in. Light Duty Retainer, Yellow 5.2
5 This is a general, all-purpose slit-tube sampler that can be used in both the geotechnical and environmental drilling industry. This sampler has a solid sleeve or extension that is threaded and connects the split tubes with the head assembly. The purpose of the extension is for retaining any loose soil which may have collected at the bottom of the test boring. The samplers are available in 12 in., 18 in., and 24 in. lengths. The sampling shoe is recessed to allow the use of a basket retainer or trap valve. The head of the assembly comes with a ball check feature that helps prevent losing a sample by washing out during withdrawal from a test boring. Liners for the split tubes are also available for specific sampling needs. This sampler is often used to determine bearing capacity of soils as required for Standard Penetration Tests. Item No. Description California Modified Samplers DS-471 DS-476 DS-477 DS-478 DS-487 DS-488 DS-489 2 in. O.D. x 18 in. with AW Box 2.5 in. O.D. x 18 in. with AW Box 2.5 in. O.D. x 24 in. with AW Box 2.5 in. O.D. x 18 in. with AWJ Box 3 in. O.D. x 18 in. with NW Box 3 in. O.D. x 24 in. with NW Box 3 in. O.D. x 18 in. with NWJ Box California Modified Sampler Replacement Parts DS-47001 DS-47002 DS-47003 DS-47004 DS-47006 DS-47007 DS-47008 DS-47101 DS-47104 DS-47105 DS-47103 DS-401 DS-402 DS-48904 DS-49004 DS-48001 DS-48002 DS-48003 DS-48004 DS-48007 DS-48008 DS-48009 DS-48006 2.5 in. O.D. AW Head 2.5 in. O.D. AWJ Head 2.5 in. O.D. Solid Sleeve 2.5 in. O.D. x 24 in. Split Barrel 2.5 in. O.D. Blunt Shoe 2.5 in. O.D. CPLG 2.5 in. O.D. Spacer 2 in. O.D. x 18 in. Head Assembly AW 2 in. O.D. x 18 in. Split Barrel 2 in. O.D. x 24 in. Split Barrel 2 in. O.D. Solid Sleeve Lynac 2 in. O.D. Shoe ASTM 2 in. O.D. Open Shoe 3 in. O.D. x 18 in. Split Barrel 3 in. O.D. x 24 in. Split Barrel 3 in. O.D. Head NW 3 in. O.D. Head NWJ 3 in. O.D. Solid Sleeve 3 in. O.D. Head AWJ 3 in. O.D. Head AW 3 in. O.D. Spacer 3 in. O.D. Coupling 3 in. O.D. Shoe Blunt SAMPLER HEAD PIN BALL CHECK SOLID SLEEVE SPLIT TUBE SHOE TRAP RETAINER OR BASKET RETAINER 5.3
Hoisting, Lowering, Hammers and Rockbits 6
5,000 lb. 10,000 lb. Hoisting Plugs Hoisting Plug 5,000 lb. Swivel Type Features: Dependable, field proven product for NQ surface drilling operations. Hoisting capacity of 2 250 kg (5,000 lbs.) Ball bearing design provides pivot for ease of connecting and reduces hoisting cable winding during hoisting and lowering. AW rod box spindle connection. Item Part Description 6 Assembly 1-8 025855 Hoisting Plug Assembly, 5,000 lb Parts Quantity 1 046123 Castle Nut 1 2 006873 Plug Ball Race 2 3 025853 Stainless Steel Ball 8 4 006870 Hoisting Plug Ball 1 5 017447 Grease Fitting 1 6 025856 Hoisting Plug Body 1 7 044617 Cotter Pin, 3/16 in. x 1 1/2 in. 1 8 006872 Plug Pivot Cap Screw 1 Hoisting Plug 10,000 lb. Features: Dependable, field proven product for NQ surface drilling operations. Hoisting capacity of 4 500 kg (10,000 lbs.) Ball bearing design provides pivot for ease of connecting and reduces hoisting cable winding during hoisting and lowering. NW rod box spindle connection. Item Part Description Assembly 1-8 025857 Hoisting Plug Assembly, 5,000 lb Parts Quantity 1 044591 Castle Nut 1 2 007698 Plug Ball Race 2 3 018782 Stainless Steel Ball 8 4 007696 Hoisting Plug Ball 1 5 017447 Grease Fitting 1 6 017651 Hoisting Plug Body 1 7 044632 Cotter Pin, 3/16 in. x 2 in. 1 8 007697 Plug Pivot Cap Screw 1 6.1
Part Description Price Part Description Price Slip Rings DZ-100 DZ-101 DZ-114 DZ-115 AW/AWJ Open Slip Ring AW/AWJ Closed Slip Ring NW/NWJ Open Slip Ring NW/NWJ Closed Slip Ring 6 Holding Irons DZ-120 AW/AWJ Holding Iron Open DZ-123 NW/NWJ Holding Iron Open Rock Bits 97100 2-15/16 in. 3-Cone Steel Tooth Rock Bit 97128 3-7/8 in. 3-Cone Steel Tooth Rock Bit 97132 4-3/4 in. 3-Cone Steel Tooth Rock Bit Hoist Plugs DZ-130 Hoisting Plug Ball Bearing x AW Pin DZ-131 Hoisting Plug Ball Bearing x AWJ Pin 351765 Hoisting Plug Ball Bearing x NWJ Pin Kwik Clamp 351802 Kwik Clamp (1-2 in. PVC/Light Rods) 4002168 Kwik Clamp 2 (2-4.5 in. PVC/Light Rods) Rod Wiper DZ-161 AWJ Rod Wiper with Handle DZ-162 NWJ Rod Wiper without Handle Other Accessories DZ-151 7/8 in. Rope (600 ft. coil) DZ-152 1 in. Rope (600 ft. coil) 6.2
Auto Hammer SPT Auto Hammer This design of hammer has been proven extensively over the years and is available for use on all makes and models of Geotechnical and Environmental drills. Specifications: Hydraulic Cylinder: 73 in. stroke Hammer Weight: 140 lbs Length of Travel: 30 in Strokes Per Minute: 1-30 (Hydraulically Variable) 6 The cylinder can be used to position the SPT Auto Hammer over the string to be driven. It can also lift the hammer so that it can be swung away from the hole for storage. Hydraulic Requirements: Maximum Psi: 1600 Psi Maximum Flow: 10 Gals/Min 6.3
Safety Hammer DS-100 140 lb. Safety Hammer x AW Connection DS-10010 Replacement AW Hammer Stem Inhole Hammer 201239 140 lb. Inhole Hammer 201630 Inhole Hammer Swivel DRIVER HOIST CABLE GIMBAL COUPLING 6 IN-HOLE SAMPLING HAMMER AW or AWJ AVAILABLE NW-AW PIN-TO-PIN SUB CUTTERHEAD SPLIT BARREL SAMPLER 6.4
THIS PAGE INTENTIONALLY LEFT BLANK
Core Barrels, Drill Rods & Casings 7
Conventional Core Barrels NV Item Part Description No. Req d 7 NV Double-Tubed Swivel Type 1-20 26675 Core Barrel Assembly, 5 ft. 0 1-20 26674 Core Barrel Assembly, 10 ft. 0 1-10 26976 Head Assembly 1 1 26677 Outer Head 1 2 24885 Lock Nut 1 3 24886 Spindle Assembly 1 4 24887 Shut-off Valve 2 5 24888 Valve Adjusting Washer 2 6A 24312 Thrust Ball Bearing 1 6B 18298 Hanger Bearing 1 7 24889 Spindle Bearing 1 8 24313 Compression Spring 1 9 24314 Self Locking Nut 1 10 40664 Inner Tube Cap Assembly (consists of 10-1, 10-2, 10-3, 10-4) 1 10-1 17447 Hydraulic Grease Fitting 1 10-2 25307 Stainless Steel Ball 1 10-3 40677 Inner Tube Cap 1 11 24909 Inner Tube, 5 ft. 1 11 24891 Inner Tube, 10 ft. 1 12 24893 Stop Ring 1 13 24894H Core Lifter 1 14 24892 Core Lifter Case 1 18 24910 Outer Tube, 5 ft. 1 18 24898 Outer Tube, 10 ft. 1 19 44407 Inner Tube Stabilizer 1 20 24900 Thread Protector (not shown) 1 Optional Accessory Equipment & Tools 31403 Inner Tube Coupling for Core Barrel Extension 1 24315 Wrench 2 inch Open End 2 NOTE: Long core barrels: The inner tube coupling permits the usse of standard parts to assembly 15 to 20 foot core barrels. Example: to order a 20 foot barrel, order the 10 foot assembly plus one extra outer tube, one extra inner tube, one extra stabilizer, and one inner tube coupling. For assembly details, refer to Boart Longyear Products manual or Wireline Instructions. 7.1
Conventional Core Barrels NV2 Item Part Description No. Req d NV2 Double-Tubed Swivel Type 1-20 44377 Core Barrel Assembly, 5 ft. 0 1-20 43608 Core Barrel Assembly, 10 ft. 0 1-10 3542994 Head Assembly, NWJ R/B 1 1 26677 Outer Head 1 2 24885 Lock Nut 1 3 24886 Spindle Assembly 1 4 24887 Shut-off Valve 2 5 24888 Valve Adjusting Washer 2 6A 24312 Thrust Ball Bearing 1 6B 18298 Hanger Bearing 1 7 24889 Spindle Bearing 1 8 24313 Compression Spring 1 9 24314 Self Locking Nut 1 10 43604 Inner Tube Cap Assembly (consists of 10-1, 10-2, 10-3, 10-4) 1 10-1 17447 Hydraulic Grease Fitting 1 10-2 25307 Stainless Steel Ball 1 10-3 43602 Inner Tube Cap 1 10-4 37382 Check Valve Body 1 11 44366CP Inner Tube, 5 ft., Chrome Plated 1 11 43601CP Inner Tube, 10 ft., Chrome Plated 1 12 29210 Stop Ring 1 13 29211H Core Lifter 1 14 29209 Core Lifter Case 1 18 24910 Outer Tube, 5 ft. 1 18 24898 Outer Tube, 10 ft. 1 19 43812 Inner Tube Stabilizer 1 20 24900 Thread Protector (not shown) 1 7 Optional Accessory Equipment & Tools 24315 Wrench 2 inch Open End 2 11A 4583221 Inner Tube, Laser Cut (Coffin Design) 11A 4583222 Inner Tube, Laser Cut (Coffin Design) NOTE: The Core Barrel Assembly, 15 ft. consists of one Head Assembly, one each Inner Tube 15 ft., Stop Ring, Core Lifter, Core Lifter case, Outer Tube 5 ft., Out Tube 10 ft., Thread Protector and two Inner Tube Stabilizers. 55 in. 60 in. Inner Tube, Laser Cut (Coffin Design) 7.2
Conventional Head Assembly V 7 7.3
Conventional Core Barrel Assembly V 7 7.4
Conventional Core Barrel NWD4 7 Core Barrel NWD4 1 2 6 7 5 8 9 10 11 12 13 3 4 Item Part Description Core Barrel NWD4 4009381 Core Barrel Assembly, 5 ft. 202458 Core Barrel Assembly, 10 ft. 201797 Core Barrel Assembly, 5 ft. Split 4008998 Core Barrel Assembly, 10 ft. Split Core Barrel NWD45 026526 Core Ejection Piston? 1 2 202112 Core Barrel Head NWJ Rod 4009385 Grease Fitting 3 201642 Outer Tube, 5ft. 3 4000231 Outer Tube, 10 ft. 4 202538 Inner Tube, 5 ft. 4 4009388 Inner Tube, 10 ft. 4 202096 Inner Tube, 5 ft. Split 4 4004391 Inner Tube, 10 ft. Split 5 202113 Bearing Assembly 6 4001541 Bearing Shaft 7 4001542 Lock Nut 8 4009393 Bearing Retainer 9 201653 Bearing, Thrust Ball (2 required) 10 4001593 Hex Nut, Flanged 11 4001544 Hex Nut, Regular 12 202278 Inner Tube Connector 13 4001660 Ball 14 201643 Core Lifter, Skirtless 15 201644 Inner Tube Shoe/Case 4009394 Thread Protector Sub Options5 201714 Blank Reaming Shell With Hard Facing 202095 Inner Tube Shoe Pilot 4009396 Blow Out Plug (Adapter) 4009397 Plunger (Piston) 4001560 Core Barrel Head NW Rod 14 15 7.5
Wireline Coring System NQ Core Barrel NQ for Q Rod Boart Longyear offers a field proven standard NQ core barrel for use with NQ rods. It consists of the head assembly (item 1), inner tube components (items 2-5), and outer tube components (items 6-11). The In-The-Hole Tools Product Manual and core barrel Safety Poster are included with all core barrels.! WARNING All head assemblies are supplied with landing indication installed. Refer to the Head Assembly section. How to Order: To order a standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. NOTE: For information on packaging and assembly, refer to the packaging and/or assembly sections. Item Part Description Price Core Barrel NQ 1-13 306001 NQ Core Barrel, 5 ft. 1-13 306002 NQ Core Barrel, 10 ft. 1-5 3542920 NQ Inner Tube Assembly, 5 ft. 1-5 3542921 NQ Inner Tube Assembly, 10 ft. Standard Configuration 1 3542751 NQ Head Assembly 2 24909 NQ Inner Tube, 5 ft. 2 24891 NQ Inner Tube, 10 ft. 3 24893 Stop Ring 4 24894H Core Lifter Hardened 5 24892 Core Lifter Case 6 62764 Locking Coupling NQ 6 3541826 Locking Coupling NRQHP 7 24896 Adapter Coupling 8 24897 Landing Ring 9 24910 Outer Tube, 5 ft. 9 24898 Outer Tube, 10 ft. 10 44407 Inner Tube Stabilizer 11 24900 Thread Protector 12 3541994 ITHT Product Manual (not shown) 13 306390 Safety Poster (not shown) 7 9 6 2 1 7 3 10 4 11 8 5 7.6
Wireline Coring System NQ 7 Head Assembly NQ! WARNING The standard head assembly is supplied with landing indication (items 15-16) installed. Landing indication must be reset by popping the ball back through the bushing after each use (see the ITHT Product Manual). If you do not wish to use landing indication it must be removed of slow descent times may result. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. NOTE: For information on packaging and assembly, refer to the packaging and/or assembly sections. 21A 21A 19 20 22 22 23 21 21 7 7 1 4 2 3 8 9 6 5 Item Part Description Head Assembly NQ 1-28 3542751 NQ Head Assembly Standard Configuration 1 42913 Spearhead Point 2 15141 Compression Spring 3 42914 Detent Plunger 4 3540329 Spearhead Base 5 42905 Spirol Pin 7/16 in. x 1 in. 6 306455 Latch Retracting Case 7 24305 Spring Pin 1/2 in. x 2 in. 8 3541932 Nyloc Bolt 3/8 in. 16UNC x 3/4 in. 9 306022 Washer 10 3541846 Latch Compression Spring 11 3541778 Upper Latch Body 12 104816 Latch 13 306454 Link 14 24548 Spring Pin 1/2 in. x 1 1/2 in. 15 62374 Stainless Steel Ball, 22 mm 16 62380 Landing Indicator Bushing 17 306009 Landing Shoulder 18 306008 Lower Latch Body 19 24885 Hex Nut 20 24886 Spindle Assembly 21 44209 Shut-Off Valve, Hard 22 24888 Valve Adjusting Washer 23 24312 Thrust Bearing 24 24889 Spindle Bearing 25 18298 Hanger Bearing 26 24313 Compression Spring 27 22918 Stover Lock Nut 28 40664 Inner Tube Cap Assembly (28A, B, C, D) 28A 17447 Grease Fitting 28B 62374 Stainless Steel Ball, 22 mm 28C 40677 Inner Tube Cap 28D 37382 Check Valve Body 24 10 25 26 27 12 13 14 11 12 13 15 28C 28A 28B 16 17 18 A1 A2 A3 A4 B 28D Optional Fluid Retention Kit for lost circulation conditions. 7.7
Wireline Coring System NQ2 Core Barrel NQ2 for Q Rod Boart Longyear offers a field proven standard NQ2 core barrel for use with NQ rods. It consists of the head assembly (item 1), inner tube components (items 2-5), and outer tube components (items 6-11). The In-The-Hole Tools Product Manual and core barrel Safety Poster are included with all core barrels.! WARNING All head assemblies are supplied with landing indication installed. Refer to the Head Assembly section. How to Order: To order a standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. NOTE: To convert your existing core barrel, see the Conversion Kits section. For information on packaging and assembly, refer to the packaging and/or assembly sections. Item Part Description Core Barrel NQ2 1-13 306012 NQ2 Core Barrel, 5 ft. 1-13 306013 NQ2 Core Barrel, 10 ft. 1-5 3542922 NQ2 Inner Tube Assembly, 5 ft. 1-5 3542923 NQ2 Inner Tube Assembly, 10 ft. Standard Configuration 1 3542752 NQ2 Head Assembly 2 44366CP NQ2 Inner Tube Chrome Plated, 5 ft. 2 43601CP NQ2 Inner Tube Chrome Plated, 10 ft. 3 29210 Stop Ring 4 29211H Core Lifter Hardened 5 29209 Core Lifter Case 6 62764 Locking Coupling NQ 6 3541826 Locking Coupling NRQHP 7 24896 Adapter Coupling 8 29214 Landing Ring 9 24910 Outer Tube, 5 ft. 9 24898 Outer Tube, 10 ft. 10 43812 Inner Tube Stabilizer 11 24900 Thread Protector 12 3541994 ITHT Product Manual (not shown) 13 306390 Safety Poster (not shown) 7 7.8
Wireline Coring System NQ2 7 Head Assembly NQ2! WARNING The standard head assembly is supplied with landing indication (items 16-17) installed. Landing indication must be reset by popping the ball back through the bushing after each use (see the ITHT Product Manual). If you do not wish to use landing indication it must be removed of slow descent times may result. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. NOTE: For information on packaging and assembly, refer to the packaging and/or assembly sections. 21A 21A 19 20 22 22 23 24 25 26 27 21 21 7 7 1 4 2 3 8 9 10 12 13 14 6 11 5 12 13 Item Part Description Price Head Assembly NQ2 1-28 3542752 NQ2 Head Assembly Standard Configuration 1 42913 Spearhead Point 2 15141 Compression Spring 3 42914 Detent Plunger 4 3540329 Spearhead Base 5 42905 Spirol Pin 7/16 in. x 1 in. 6 306455 Latch Retracting Case 7 24305 Spring Pin 1/2 in. x 2 in. 8 3541932 Nyloc Bolt 3/8 in. 16UNC x 3/4 in. 9 306022 Washer 10 3541846 Latch Compression Spring 11 3541778 Upper Latch Body 12 104816 Latch 13 306454 Link 14 24548 Spring Pin 1/2 in. x 1 1/2 in. 15 62374 Stainless Steel Ball, 22 mm 16 62380 Landing Indicator Bushing 17 306026 Landing Shoulder 18 306025 Lower Latch Body 19 24885 Hex Nut 20 24886 Spindle Assembly 21 44209 Shut-Off Valve, Hard 22 24888 Valve Adjusting Washer 23 24312 Thrust Bearing 24 24889 Spindle Bearing 25 18298 Hanger Bearing 26 24313 Compression Spring 27 22918 Stover Lock Nut 28 43604 Inner Tube Cap Assembly (28A, B, C, D) 28A 17447 Grease Fitting 28B 62374 Stainless Steel Ball, 22 mm 28C 43602 Inner Tube Cap 28D 37382 Check Valve Body 15 28C 28A 28B 16 17 18 A1 A2 A3 A4 B 28D Optional Fluid Retention Kit for lost circulation conditions. 7.9
Wireline Coring System NQ2 Split Core Barrel NQ2 for Q Rod Boart Longyear offers a field proven standard NQ2 core barrel for use with NQ rods. It consists of the head assembly (item 1), inner tube components (items 2-5), and outer tube components (items 6-11). The In-The-Hole Tools Product Manual and core barrel Safety Poster are included with all core barrels. All head assemblies are supplied with landing indication installed. Refer to the Head Assembly section. How to Order: To order a standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. 9 6 2 1 Item Part Description Split Core Barrel NQ2 1-13 4001327 NQ2 Core Barrel, 5 ft. 1-13 4001328 NQ2 Split Core Barrel, 10 ft. 1-5 4001425 NQ2 Inner Tube Assembly, 5 ft. 1-5 4002332 NQ2 Inner Tube Assembly, 10 ft. Standard Configuration 1 3542752 NQ2 Head Assembly 2 4583221 NQ2 Lasercut Inner Tube, 5 ft. 2 4583222 NQ2 LasercutInner Tube, 10 ft. 3 29210 Stop Ring 4 29211H Core Lifter Hardened 5 29209 Core Lifter Case 6 62764 Locking Coupling NQ 7 24896 Adapter Coupling 8 29214 Landing Ring 9 24910 Outer Tube, 5 ft. 9 24898 Outer Tube, 10 ft. 10 43812 Inner Tube Stabilizer 11 24900 Thread Protector 12 3541994 ITHT Product Manual (not shown) 13 306390 Safety Poster (not shown) 7 Side 55 in. 60 in. Top 7 10 3 4 Cover Open 11 8 5 Inner Tube, Laser Cut (Coffin Design) 7.10
Wireline Coring System Split Tube is Pumped from Inner Tube NQ-3 The core-laden split tube is pumped from the inner tube using a Longyear hand-operated hydraulic pump. Also available is a pump-out group designed to permit use of the drilling pump. The piston protects the core from water pressure and gently 7 7.11
Wireline Coring System NQ3 Core Barrel NQ3 for Q Rod Boart Longyear offers a field proven standard NQ 3 core barrel for use with NQ rods. It consists of the head assembly (item 1), inner tube components (items 2-10), and outer tube components (items 11-16). The In-The-Hole Tools Product Manual and core barrel Safety Poster are included with all core barrels. Triple-tube core barrels are commonly selected when drilling coal, clay bearing or highly fractured formations. A second inner tube (split lenthwise) is contained inside the standard inner tube. The core ejection piston protects the core from pressurized drilling fluid when the split inner tube, containing the core sample, is pumped out of the standard inner tube. Upon removal, one half of the split tube is lifted off to reveal the undisturbed core sample.! WARNING All head assemblies are supplied with landing indication installed. Refer to the Head Assembly section. How to Order: To order a standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. NOTE: To convert your existing core barrel, see the Conversion Kits section. For information on packaging and assembly, refer to the packaging and/or assembly sections. Item Part Description Core Barrel NQ3 1-18 3540572 NQ3 Core Barrel, 5 ft. 1-18 3540573 NQ3 Core Barrel, 10 ft. Standard Configuration 1 3542751 NQ Head Assembly 2 026532 Pump-Out Adapter, 1/4in. NPT-F* 3 026662 Piston Plug** 4 026134 O Ring 5 026526 Core Ejection Piston 6 026527 Split Tube, 5 ft. 6 026528 Split Tube, 10 ft. 7 024909 Inner Tube, 5 ft. 7 024891 Inner Tube, 10 ft. 8 026530 Stop Ring 9 026531 Core Lifter, Fluted 10 026529 Core Lifter Case 11 062764 NQ Conventional Locking Coupling 12 024896 Adapter Coupling 13 024897 Landing Ring 14 024910 Outer Tube, 5 ft. 14 024898 Outer Tube, 10 ft. 15 044407 Inner Tube Stabilizer 16 024900 Thread Protector 17 3541994 ITHT Product Manual (not shown) 18 306390 Safety Poster (not shown) 7 14 9 10 4 5 1 Inner Tube Loading Sleeve, reference only. 6 11 7 15 12 3 2 ** These items are required to pump the core out of the inner tube. Remove the head assembly from the inner tube, insert the poston plug and thread the pump out adapter on to the inner tube. 16 13 8 7.12
Wireline Coring System NQ3 7 Head Assembly NQ3! WARNING The standard head assembly is supplied with landing indication (items 16-17) installed. Landing indication must be reset by popping the ball back through the bushing after each use (see the ITHT Product Manual). If you do not wish to use landing indication it must be removed of slow descent times may result. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. NOTE: For information on packaging and assembly, refer to the packaging and/or assembly sections. 21A 21A 19 20 22 22 23 21 21 7 7 1 4 2 3 8 9 6 5 Item Part Description Head Assembly NQ2 1-28 3542752 NQ1 Head Assembly Standard Configuration 1 42913 Spearhead Point 2 15141 Compression Spring 3 42914 Detent Plunger 4 3540329 Spearhead Base 5 42905 Spirol Pin 7/16 in. x 1 in. 6 306455 Latch Retracting Case 7 24305 Spring Pin 1/2 in. x 2 in. 8 3541932 Nyloc Bolt 3/8 in. 16UNC x 3/4 in. 9 306022 Washer 10 3541846 Latch Compression Spring 11 3541778 Upper Latch Body 12 104816 Latch 13 306454 Link 14 24548 Spring Pin 1/2 in. x 1 1/2 in. 15 62374 Stainless Steel Ball, 22 mm 16 62380 Landing Indicator Bushing 17 306009 Landing Shoulder 18 306008 Lower Latch Body 19 24885 Hex Nut 20 24886 Spindle Assembly 21 44209 Shut-Off Valve, Hard 22 24888 Valve Adjusting Washer 23 24312 Thrust Bearing 24 24889 Spindle Bearing 25 18298 Hanger Bearing 26 24313 Compression Spring 27 22918 Stover Lock Nut 28 40664 Inner Tube Cap Assembly (28A, B, C, D) 28A 17447 Grease Fitting 28B 62374 Stainless Steel Ball, 22 mm 28C 40677 Inner Tube Cap 28D 37382 Check Valve Body 24 25 26 27 28C 28A 28B 10 12 13 14 15 16 17 18 11 13 12 A1 A2 A3 A4 B Head Assembly Options 21A 24887 Shut-Off Valve, Soft Optional Fluid Retention* A 3542610 Fluid Retention Kit A1 62374 Stainless Steel Ball, 22 mm A2 306131 Fluid Retention Bushing A3 104966 Fluid Retention Spring, Light A4 104971 Fluid Retention Spring, Medium Fluid Retention Optional Spring B 104972 Fluid Retention Spring, Heavey This kit can replace landing indication when drilling in lost circulation conditions. 28D Optional Fluid Retention Kit for lost circulation conditions. 7.13
Wireline Coring System NQ3 Inner Tube Components NQ3 Standard inner tube components (items 1-10) can be ordered as part of the standard core barrel or as an inner tube group. To order inner tube components apart fron the core barrel, please use the inner tube group numbers provided and specify any options you may require. If ordering these components as part of a core barrel, p0lease refer to the ordering instructions below. All inner tube groups are shipped as components and are not assembled.! WARNING All head assemblies are supplied with landing indication installed. Refer to the Head Assembly section. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. Item Part Description Inner Tube Group 1-10 3542924 NQ3 Inner Tube Group, 5 ft. 1-18 3542925 NQ3 Inner Tube Group, 10 ft. Standard Configuration 1 3542751 NQ Head Assembly* 2 026532 Pump-Out Adapter, 1/4in. NPT-F** 3 026526 Core Ejection Piston** 4 026134 O Ring 5 026662 Piston Plug 6 026527 Split Tube, 5 ft. 6 026528 Split Tube, 10 ft. 7 024909 Inner Tube, 5 ft. 7 024891 Inner Tube, 10 ft. 8 026530 Stop Ring 9 026531 Core Lifter, Fluted 10 026529 Core Lifter Case See the head assembly section for a detailed configuration and available options. Chrome plated inner tubes (full length inside diameter) can not be used with triple-tube core barrels. Inner tube extensions for use with stabilized reaming shells can not be used with the triple-tube core barrel. Triple-tube core barrels can not be extended with inner tube couplings. 7 Inner Tube Loading Sleeve, reference only. ** These items are required to pump the core out of the inner tube. Remove the head assembly from the inner tube, insert the poston plug and thread the pump out adapter on to the inner tube. 7.14
Wireline Coring System NQ3 Outer Tube Components NQ3 Standard outer tube components (items 11-16) are included in the standard core barrel for use with NRQHP or NQ rods.! WARNING All head assemblies are supplied with landing indication installed. Refer to the Head Assembly section. How to Order: To order a non-standard core barrel: Select a 1.5 m/5 ft. or 3.0 m/10 ft. core barrel part number. List all optional parts and part numbers from the head assembly, inner tube omponents and/or outer tube components sections. Item Part Description Price Outer Tube Components 11 062764 NQ Conventional Locking Coupling 12 024896 Adapter Coupling 13 024897 Landing Ring 14 024910 Outer Tube, 5 ft. 15 024898 Outer Tube, 10 ft. 16 024900 Thread Protector Optional Chrome Plating To order chrome plated outer tubes 18 in./ 45 cm at both ends on the outside diameter, use the following part numbers. 14A 24910CP Outer Tube CP, 5 ft. 14A 24898CP Outer Tube CP, 10 ft. 7 7.15
Wireline Coring System NQ Overshot Compact Overshot NQ Features: For surface or downhole applications with NQ/NQ3/NQ2 core barrels. Stonger lifting dogs and lifting dog compression spring. Threaded connection between jar staff and overshot head. High strength alloy steel jar staff with increased diameter and fail safe stop. Eye bolt machined with radius to eliminate need for thimble. Dry Hole Lowering: In dry holes, the overshot assembly is used to lower the inner tube assembly. The locking sleeve will release the inner tube assembly upon contact with the water table or when the landing shoulder makes contact with the landing ring. The taper on the spearhead point forces the top end of the lifting dogs inward, allowing the locking sleeve to drop down and lock the lifting dogs open. The set screw (#16) can be used when dry hole lowering to prevent the locking sleeve from cable jumping.! WARNING The inner tube assembly can be released prematurely if it encounters resistance inside the rod string that resembles contact with the water table or landing shoulder, i.e. bulged rod joints. Releasing the Overshot Assembly: If the inner tube assembly becomes stuck in the outer tube, the locking sleeve is used to release the overshot. The locking sleeve is guided onto the wireline cable through the guide slot and dropped to the overshot/inner tube assembly. The locking sleeve drops over the lifting dogs and locks them open to allow the overshot to be pulled from the hole. NOTE: Refer to the ITHT Product Manual for additional operating information. Item Part Description Compact Overshot NQ 1-17 3540530 NQ Overshot Assembly 1-5 25984 Cable Swivel Assembly Parts 1 25991 Eye Bolt 2 25990 Cable Swivel Collar 3 25986 Thrust Bearing 4 25985 Castle Nut 5 44615 Cotter Pin 6 17447 Grease Fitting 7 44444 Cable Swivel Body 8 3540516 Jar Staff 9 3540515 Jar Tube 10 102231 Hex Nut 11 3540517 Overshot Head 12 3542027 Compression Spring 13 3540529 Lifting Dog 14 42906 Plain Pin 15 37394 Spring Pin 16 44442 Set Screw 17 15965 Locking Sleeve 7 7.16
Core Boxes and Wrenches Full Grip Full Grip Wrenches: Inner and Outer tube wrenches feature a unique design that assures positive gripping with no distortion of the tube. Item No. Description 7 Core Boxes 79737 NQ/NX Core Box 79738 HQ Core Box 79739 PQ Core Box Wrenches 28255 NQ Outer Tube Wrench 25319 NQ Inner Tube Wrench 28252 NQ2 Inner Tube Wrench 7.17
Geo Core Barrels 101mm Extended Shoe/Split Inner Tube 2in. x 30 in. Shelby Tube Full Hole Boring Hard Rock Coring Item Part Description No. Req d Extended Shoe/Split Tube Sampling 1 54685 101mm GEO Core Barrel Assembly w/ 2 in. Extended Shoe 1 2 2 2 in. x 30 in. Shelby Tube Sampling 2 54233 Spindle Adjusting Washer 4 3 54229 5 ft. Rigid Spindle 1 4 54688 2 in. Head Assembly 1 5 47529 Cap Screw (1/4 in. - UNC) 4 6 GO10261 Shelby Tube Sampler 2 in. O.D. and 30 in. Length 1 Full Hole Boring 3 3 2 54233 Spindle Adjusting Washer 4 3 54229 5 ft. Rigid Spindle 1 7 54682 Driver to Drag and Roller Cone Bit Sub 1 4 8 9 10 11 13 12 14 15 19 17 18 Hard Rock Coring 8 25231 Spindle Assembly 1 9 43513 Shut-off Valve 2 10 25233 Valve Adjusting Washer 2 11 24528 Ball Thrust Bearing 2 12 24312 Hanger Bearing 1 13 25234 Spindle Bearing 1 14 24529 Compression Spring 1 15 24530 Self Locking Nut 1 16 40678 Inner Tube cap Assembly (consists of 17, 18, 19 and 20) 1 17 17447 Hydraulic Grease Fitting 1 18 25307 Stainless Steel Ball 1 19 40401 Inner Tube Cap 1 20 37382 Check Valve Body 1 21 54695 GEO Inner Tube Extension 1 22 25238 Stop Ring 1 23 25239H Core Lifter 1 24 25237 Core Lifter Case 1 25 25258 Inner Tube, 5 ft. 1 7 5 20 Optional Equipment 6 7 21 25 22 23 41480 Thread Protector 54743 Full Closure Basket Lifter GO10348 Shelby Tube, 2 in. O.D. x 18 in. Long 44450 Complete Overshot Assembly BIT SELECTION Bits as selected by customer not included in system. Available options include: 97180 Roller Cone Bit 2-3/8 in. 97204 3-Wing Drag Bit 2-1/4 in. A1QEVD/* Tungsten Carbide Bit A1QZUD/* Series 2 Hard Rock Bit (*O.D. Gauge Optional) *Prices available upon request. 7.18
Casing Advancer Part No. Type Casing Advancer Assemblies 59000 NW 59075 HW 59084 HQ 3000863 HWT 59398 PW NOTE: Other sizes available on request. 7 For the first time a Casing Advancer assembly which allows you simple removal and replacement of the advancer with ensured positive relocation 7.19 Wireline casing advancers provide an efficient one step method of drilling through overburden and casing off to bedrock. Until now removing and replacing the advancer inner assembly for soil sampling, coring or bit changing was an unreliable and difficult procedure. How could you be sure that the advancer assembly would relocate correctly in the driving sleeve? Self-regulating Stop Latches Boart Longyear has developed simple self-regulating stop latches (patent pending) which reliably and accurately relocate the inner assembly in the driver no matter what the condition of the overburden. Removal and replacement of the Boart Longyear Casing Advancer is rapid, easy and positive. No special presetting or positioning of the latch mechanism is required prior to insertion; just lower it through its loading sleeve into the casing. Self-regulating Stop Latches locate the inner assembly accurately in the driver sleeve. Spring-loaded Drive Latches engage with driving keys and positively latch into the key recess until the weight of the inner assembly is taken by an overshot. Coring and Soil Sampling as required Overburden coring and soil sampling can be carried out with confidencs as often as required. The Boart Longyear Casing Advancer inner assembly returns quickly and positively to the keyed driving recess in the sleeve. Changing bits to optimize penetration rates is also now possible. Positive Latching, Positive Reaming For maximum drilling efficiency the postion of the drilling bit relative to the casing shoe is important. Correct position prolongs the life of the casing shoe by ensuring that it only does the job it was designed for; sizing the drilled hole for the casing. Boart Longyear s positive latching, case hardened drive latches securely locate the inner assembly and bit at a predetermined distance in front of the shoe. This distance is adjustable by the driller to suit the nature of the overburden and the type of bit being used.
Drill Rods and Casing W, J and Q Part Description Series W Drill Rod 15911 AW Drill Rod, 2 ft. 15912 AW Drill Rod, 5 ft. 15913 AW Drill Rod, 10 ft. 15630 Coupling For AW Drill Rod 15921 NW Drill Rod, 2 ft. 15922 NW Drill Rod, 5 ft. 15923 NW Drill Rod, 10 ft. Series WJ Drill Rod 63094 AWJ Drill Rod, 2 ft. 62786 AWJ Drill Rod, 5 ft. 62785 AWJ Drill Rod, 10 ft. 63098 NWJ Drill Rod, 2 ft. 62999 NWJ Drill Rod, 5 ft. 3543046 NWJ Drill Rod, 10 ft. Heat Treated Q Wireline Drill Rod 51564 NQ Drill Rod (HT), 5 ft. 51565 NQ Drill Rod (HT), 10 ft. 51570 HQ Drill Rod (HT), 5 ft. 51571 HQ Drill Rod (HT), 10 ft. Rods and Casing 7 4130 W Series Flush Joint Casing and Shoes 100603 NW Flush Joint Casing, 2 ft. 100602 NW Flush Joint Casing, 5 ft. 100601 NW Flush Joint Casing, 10 ft. 30108 NW Casing Drive Shoe 100597 HW Flush Joint Casing, 2 ft. 100596 HW Flush Joint Casing, 5 ft. 100595 HW Flush Joint Casing, 10 ft. 30109 HW Casing Drive Shoe * 1026 Casing available on request at economy prices. 7.20
THIS PAGE INTENTIONALLY LEFT BLANK
Diamond Products 8
Diamond Bits Impregnated Impregnated Bits Selection 8 Series 1 Series 1A Series 2 Series 4 Series 6 Series 6A Series 7 Series 7A Series 8 Diamond Bits New series 1 recommended for abrasive fractured formations yet designed to drill in variable conditions can drill through competent regions. This bit is a compromise between the Series 1 and the Series 2. Primarily recommended for high powered drills. New enhanced series 1A. This bit is targeted for extremely broken and/or highly abrasive formations. A heavy gauge protection is utilized and the matrix is specifically blended to maximize diamond retention and thus provide maximum life. While this bit is recommended for the most abrasive conditions it also has a free cutting action. Primarily recommended for high powered drills with high torque, high thrust capability. For medium abrasive or broken formations. A durable, versatile, general purpose bit for use on all types of adequately powered drills. A new product for medium hard abrasive or slightly broken formations recommended for geotechnical and lower powered drills but also successful performance on high powered drills. Bit is characterized by excellent cutting action. For medium hard moderately abrasive competent or moderately broken formations will drill a wide range of rock types. A tougher Series 6 bit. Designed for longer life especially in more abrasive/fractured formations. Particularly recommended for high-powered drills and noted for its good penetrating bit. New bit for hard, moderately abrasive and fractured formations. This is a tough, relatively free cutting, fast penetrating bit. Excellent cutting action and bit life in the harshest conditions in this range. For medium hard mostly competent somewhat abrasive conditions. Can handle higher rotation speeds and bit loads for best results. For hard competent very slightly abrasive formations. This free cutting fast penetrating bit requires high rotational speeds with reduced bit loads for best results. Series 8A Series 8F Series 9 Series 10 8.1 Free cutting, fast penetrating bit for medium hard to hard formations with excellent bit life. Stands out in abrasive formations. Can handle more bit weight than recommended in the tables without reducing bit life. Smooth, free cutting bit for medium hard to hard formations. This bit runs best with reduced bit pressures while maintaining or improving bit life. Free cutting bit with very good bit life for hard competent rock. If it can be helped this bit should not encounter broken formations. This bit excels in hard to ultra-hard, non abrasive formations. High penetration rates are possible. The express design is recommended with higher rotational speeds. Ideal for drills of all power.
Diamond Bits Impregnated Item No. Description Impregnated Bits NQ 4050085 NQ Series 2 4050088 NQ Series 4 4050089 NQ Series 6 4050092 NQ Series 8 4050095 NQ Series 10 NQ2 4050182 NQ2 Series 2 4050243 NQ2 Series 4 4050183 NQ2 Series 6 4050181 NQ2 Series 8 4050180 NQ2 Series 10 NQ3 4050178 NQ3 Series 2 4050336 NQ3 Series 6 4050335 NQ3 Series 8 NWD4 4050237 NWD4 Series 2 4050164 NWD4 Series 4 4050238 NWD4 Series 6 4050299 NWD4 Series 8 4050375 NWD4 Series 10 Express Impregnated Bit (requires twice the normal water) NQ 4050176 NQ Series 6, Express 4050333 NQ Series 8, Express NQ2 4050025 NQ2 Series 6, Express 4050026 NQ2 Series 8, Express NWD4 4050432 NWD4 Series 6, Express 4050485 NWD4 Series 8, Express 8 Devils Nightmare Carbide Bit NQ 1NQEVP/1 NQ Bit Type Devils Nightmare 1NYEVP/1 NQ2 Bit Type Devils Nightmare ANQEVP/1 NQ Devils Nightmare Core Bit ANYEVP/1 NQ2 Devils Nightmare Core Bit Devil s Nightmare 8.2
Diamond Bits Stratapax Polycrystalline Diamond Compact (PDC) also commonly known as Stratapax Bits are ideal for drilling in soft to mediumhard sedimentary formations which are homogenious and competent. The PDC cutters are available in several sizes and are located to yield maximum penetration rate and long life depending on the application. The bits are constructed with a tough, wear-resistant matrix body and gage reinforcement. As a result, worn cutters can be rotated allowing the continued use of the bit. An operating range of 100-600 rpm is generally recommended to reduce vibrations and deflections. Note: Before placing an order, we recommend you discuss your specific application with one of our representatives. Because this is a specialty bit, we wish to ensure the product we supply is suited to the applications. 8 Size OD Guage Features NWC3 3.032 Face Discharge,4 Large Cutters NWD3 3.125 Face Discharge,9 Small Cutters, Eutalloy Hardfacing NWD4 3.032 Face Discharge,7 Small Cutters, Pilot Shoe NQ 3.125 Face Discharge,6 Large Cutters NQ-3 3.032 NQ2 3.032 6 Small Cutters,.500 Broach HWD3 4.250 Face Discharge HQ 3.895 Face Discharge, 6 waterways, 12 small cutters HQ-3 3.895 PQ 5.000 PQ-3 5.000 8 Large Cutters 94 mm PC 4.875 CHD101 4.250 6 Large Cutters CHD134 5.500 Special features or options are available upon request. Extra heavy-duty gauge Face discharge Hard facing Oversize shank 8.3
Diamond Products Casing Shoes Boart Longyear s impregnated and surface set casing shoes are heavy duty products which can match up to the toughest formations. With the use of very resilient matrix to optimize diamond retention, they will hold up in very abrasive, unfriendly formations. Boart Longyear ECONO casing shoes are designed to penetrate soft or loose formations. Item No. Description 4050981 NW 4051001 HW 4051000 HWT Item No. 4051070 NW 4051034 HW 4051069 HWT Description *Other sizes available Oversized casing shoes available upon request. Oversized casing shoes are recommended when using Boart Longyear casing advancer. Special features or options available. 8 8.4
Diamond Products Reaming Shells Reaming Shells: Based on Customer input and product research we have developed a new line of reaming shells which are available in both our Standard Straight Pad and our Spiral Pad products. The new reaming shells offer the following improvements: 1. Matrix: The new matrix improves wear resistance and diamond retention. The new reaming shell is tougher: it can withstand more shock and vibration stresses because the increased ductility of the matrix forms a much stronger bond with the steel blank. 2. Pad Setting pattern: The diamond and carbide reinforcement setting pattern has been modified to give extra protection to areas that are more susceptible to premature wear. 3. Design: The entire reamer, pad and waterway matrix has been extended to the shoulder. Because the reamer pads start right at the bit joint, the wear resistance of the reamer s leading edge is improved, which results in longer life. Particularly recommended in abrasive conditions. 8 Boart Longyear ECONO shells are recommended for lighter applications where there is no extensive diamond core drilling but where intermittent or spot coring is the task at hand. ECONO shells are preferred in geotechnical and other shallow hole explorations. The longer pads have more diamonds and carbide reinforcement which offers longer life. Item No. Reaming Shells 6NQP87/4 6NQPUG/1 6NGP87/2 Description NQ RSG Surface Set Reaming Shell NQ RSG Econo Reaming Shell NWD4 Diamond Reaming Shell 8.5
Diamond Bits Surface Set Surface Set Bits Semi-Round Crown The semi-round crown (also known as B profile) is a good general-purpose bit, suitable for a wide variety of conditions depending on the diamond grade and size selected. It offers good strength especially in broken formations. Pilot Crown The pilot crown (also known as F profile) is particularly good for core recovery in soft consolidated formations, especially when face-discharge waterways are incorporated. This profile offers improved stability and reduced vibration. Pilot Crown with Face Discharge Ports The face discharge crown features extended ports to minimize sample erosion, thereby increasing core recovery in delicate formations. 8 Step Type Crown The step type crown provides stabilized drilling capabilities and improves penetration in hard and competent formations. Sizes Available AW34 AQ BW44 BWC3 BWD4 BQ BWG BQ-3 BXEWL NWC3 NWD4 NQ NWM NXEWL NWG NQ-3 NQ2 HWD3 HWD4 HQ *Other sizes available **These bits also fit the Geo Barrel of the corresponding size. Waterway Type: standard size, straight Special features or options are available upon request at an additional charge. HQ-3 PQ 4 X 5-1/2 6 X 7-3/4 2-3/8 X 3-7/8 CHD101 CHD134 8.6
Diamond Bits Surface Set Item No. Description Surface Set Bits NQ 1NQF75/1 Pilot Crown Type, SEL 25/35 1NQ485/1 Step Type, SPS 25/35 1NQB75/3 Semi-Round Type, SEL 25/35 1NQB85/6 Semi-Round Type, SEL 15/25 NQ2 1NYB85/1 Semi-Round Type, SEL 15/25 1NY353/1 Step Type, SPS 25/35 1NYB75/1 Semi-Round Type, SEL 25/35 NWD4 INGF95/2 Surface Set, 10/15 INGG85/3 Surface Set, 15/25 INGF85/1 Surface Set One-Step, 15/25 INGF75/2 Surface Set One-Step, 25/35 Selection of Surface Set Diamond Products 8 10 to 15 SPC 25 to 35 SPC 45 to 55 SPC SANDSTONE LIMESTONE GABBRO SHALE DOLOMITE LIMESTONE WITH CHERT GYPSUM AND TALC DENSE SANDSTONE WEATHERED GRANITE 8.7
Thin Wall Bits & Saw Blades 9
Diamond Coring Thin Wall Bits Thin Wall Diamond Core Bits Part Description There is a great variety of Boart Longyear grades and types available to cover a wide range of jobs. The two types we offer here are our most popular types for general-purpose wet drilling in reinforced concrete and asphalt. Boart Longyear diamond bits are single-piece construction for ease of operation. The bit adapter from the drill motor to the bit tube is an integral part of the bit tube so that it cannot get lost or be misaligned in set up. Thread type: 1-1/4 in., 7 tpi (threads per inch) Standard tube length for bits with diameters 1/2 in. through 11 in. (12.7 to 279 mm) is 15 in. (381 mm) Bit sizes are subject to manufacturing tolerances. Size of drill hole is not guaranteed or warranted. NOTE: All bits in the table are Gold 4.7 grade and have a depth of impregnation of 0.300 in. (7.62 mm) B30 (for heavily reinforced concrete) C-85208 2 in. bit, 2.050 in. OD x 1.760 in. ID C-86079 2 1/4 in. bit, 2.300 in. OD x 2.010 in. ID C-85219 3 in. bit, 3.050 in. OD x 2.760 in. ID C-86085 3 1/4 in. bit, 3.300 in. OD x 3.010 in. ID C-85230 4 in. bit, 4.050 in. OD x 3.760 in. ID C-86089 4 1/4 in. bit, 4.300 in. OD x 4.010 in. ID C-85204 6 in. bit, 6.000 in. OD x 5.710 in. ID C-86095 6 1/4 in. bit, 6.250 in. OD x 5.960 in. ID C-85252 8 in. bit, 8.063 in. OD x 7.688 in. ID B32 (for general cured concrete) C-820869 2 in. bit, 2.050 in. OD x 1.760 in. ID C-828824 2 1/4 in. bit, 2.300 in. OD x 2.010 in. ID C-821840 3 in. bit, 3.050 in. OD x 2.760 in. ID C-834674 3 1/4 in. bit, 3.300 in. OD x 3.010 in. ID C-820870 4 in. bit, 4.050 in. OD x 3.760 in. ID C-827408 4 1/4 in. bit, 4.300 in. OD x 4.010 in. ID C-821135 6 in. bit, 6.000 in. OD x 5.710 in. ID C-827411 6 1/4 in. bit, 6.250 in. OD x 5.960 in. ID C-827414 8 in. bit, 8.063 in. OD x 7.688 in. ID B50 (for asphalt or sandstone) 9 C-834885 2 in. bit, 2.050 in. OD x 1.760 in. ID C-834748 2 1/4 in. bit, 2.300 in. OD x 2.010 in. ID C-834743 3 in. bit, 3.050 in. OD x 2.760 in. ID C-834817 3 1/4 in. bit, 3.300 in. OD x 3.010 in. ID C-820663 4 in. bit, 4.050 in. OD x 3.760 in. ID C-828560 4 1/4 in. bit, 4.300 in. OD x 4.010 in. ID C-829202 6 in. bit, 6.000 in. OD x 5.710 in. ID C-834820 6 1/4 in. bit, 6.250 in. OD x 5.960 in. ID C-834612 8 in. bit, 8.063 in. OD x 7.688 in. ID NOTE: Other diameters available on request. 9.1
Diamond Sawing Blades Diamond Saw Blades for dry cutting with hand-held saws For use on hand-held gasoline or electric saws with a maximum blade rpm of 6000, the dry cutting Boart Longyear series of blades offers a variety of specifications for most concrete, stone, tile, and masonry materials. Among these, we are showing in the table below our two most popular general-purpose blades. For more choices or specific applications, please contact your Boart Longyear representative. Part Saw Blades Description C-831700 14 in. dia. x.125 width (for concrete) C-841854 14 in. dia. x.125 width (for asphalt only) Dimensions: Diameter 14 in. (355 mm) Segment Width 0.125 in. (3.2 mm) Arbor Size 1 in. (25.4 mm)* *To fit blade to 20 mm arbor, use P/N C-8D40095, 1 in. to 20 mm reducing bushing. NOTE: Other sizes available on request. 9 9.2
THIS PAGE INTENTIONALLY LEFT BLANK
Water Swivels & Pumps 10
6RG and 12RG Features: Available in two (2) sizes Manufactured from high grade alloy steel Working pressures to 500 PSI Radial ball bearings for smooth rotation Non adjustable chevron (V-ring) packing Grease lubricated Can be used for both mud and air drilling Can be repaired if necessary in the field 6RG Water Swivels 12RG 6RG and 12RG Technical Data Part No. Overall Length Width Upper Hose Conn. Lower Conn. Watercourse Conn. 10 6RG 13-1/2 in. 4 in. 1-5/8 in. hex 1 in. AW Box 5/8 in. 12RG 14-1/16 in. 5 in. 1-5/8 or 2 in. hex 1-1/4 in. NW Box 1-1/4 in. Item No. Part No. Description No. Required Wt./Lbs. 6RG and 12RG 6RG Parts 6RG Water Swivel 22.00 12RG Water Swivel 22.00 1 6RG-01 Stem, 1 5/8 in. Hex by AW Box 1 9.50 2 6RG-04 Packoff Housing 1 8.50 3 6RG-05 Packing Set 2.50 4 6RG-26 Bearings 2 2.30 5 6RG-325 Retainer, Packing 2.10 6 6RG-354 Retainer, Bearing 2.10 12RG Parts 7 12RG-01 Stem, 1 5/8 in. Hex by NW Box Option 16.50 7 12RG-01 Stem, 2 in. Hex by NW Box Option 18.00 8 12RG-04 Packoff Housing 1 14.50 9 12RG-05 Packing Set 2.50 10 12RG-26 Bearings 2 2.50 11 12RG-400W Retainer, Packing 2.10 12 12RG-433W Retainer, Bearing 2.10 13 13RG-05 Packing Seat Ring 2.50 10.1
Water Swivels King Item No. Part No. Description Drilling Fluid Swivels and Parts DZ-300 King Water Swivel, 1J 1.25 LH NPT lower 1 DZ-30010 King, 1J3, Packing (2 required) 2 DZ-30019 King, 1J, Bearing 3 DZ-30020 King, 1J4, Wearing Bushing (1 required) 4 DZ-30030 King, 1J7, Housing Seal (2 required) DZ-301 King Water Swivel, 2J 1.5 LH NPT lower 1 DZ-30110 King, 2J3, Packing (2 required) 2 DZ-30119 King, 2J, Bearing 3 DZ-30120 King, 2J4, Wearing Bushing (1 required) 4 DZ-30130 King, 2J7, Housing Seal (2 required) 5 DZ-30121 King, 2J, Lower LH Conn. DZ-400 King Water Swivel, 5EL 2.0 LH NPT lower 1 DZ-40010 King, 5EL, Packing (2 required) 3 DZ-40020 King, 5EL, Wearing Bushing (1 required) Bail with nuts 10 10.2
1JW and 2JW Features: For all types of drilling requiring a small light weight swivel Alloy steel BAIL, SPINDLE, and LOWER CONNECTION High thrust ball bearings in a grease lubricated sealed housing Simple design allows quick packing replacement and easy field repairs. Available with several different hose connections Special lower connections available upon request Water Swivel Classical Gooseneck with Bail Part No. Static Load Drill Depth Drill Pipe Size 1JW 5,000 lbs. 500 ft. @ 100 RPM 1-1/4 in. stand. pipe 2JW 7,000 lbs. 500 ft. @ 100 RPM 2 in. stand. pipe Technical Data Part No. Length Hose Conn. NPT Lower Conn. LH or RH NPT Water Course Working 1JW 13 in. 1 in. female / 1-1/4 in. male 1 in. or 1-1/4 in. 1 in. 300 psi 2JW 16 in. 1-1/2 in. female / 2 in. NPT 1-1/2 in. or 2 in. 1-1/2 in. 300 psi Item No. Part No. Description No. Req d Wt./Lbs. Spares 1yr. 10 1JW and 2 JW 1JW 2JW 10 (alum) 15 (iron) 14 (alum) 21 (iron) 10.3 1JW Parts 1 1JW-01A** Gooseneck, Aluminum Option 1.56 2 1JW-01** Gooseneck, Iron 1 4.12 3 1JW-02 Bail with Nuts 1 1.62 4 1JW-03 Packing 2.03 6 5 1JW-03-90 Packing 90 Duro Option.03 6 1JW-04 Wearbushing 1.18 1 7 1JW-05 Bearing Spindle 1 1.12 8 1JW-06** Lower Connection Option 1.50 9 1JW-07 Housing Seal 2.06 2 10 1JW-08A Brg Housing, Aluminum Option 1.50 11 1JW-08 Brg Housing, Iron 1 4.00 1 12 1JW-09 Bearing 2 1.68 2 2JW Parts 1 2JW-01A** Gooseneck, Aluminum Option 2.12 2 2JW-01** Gooseneck, Iron 1 5.62 3 2JW-02 Bail with Nuts 1 2.06 4 2JW-03 Packing 2.04 6 5 2JW-03-90 Packing 90 Duro Option.04 6 2JW-04 Wearbushing 1.25 1 7 2JW-05 Bearing Spindle 1 2.00 8 2JW-06** Lower Connection Option 2.50 9 2JW-07 Housing Seal 2.06 2 10 2JW-08A Brg Housing, Aluminum Option 2.00 11 2JW-08 Brg Housing, Iron 1 5.50 1 12 2JW-09 Bearing 2 2.25 2
Pumps and Parts MOYNO Item Part Description Item Part Description Frame 4 Design Pumps 2L DP-100 Pump, Complete Assembly 3L DP-105 Pump, Complete Assembly A DP-110 Ball Bearing (Radial) B DP-111 Ball Bearing (Thrust) C DP-112 Bearing Spacer D DP-113 Bearing Lock Nut E DP-114 Bearing Lock Washer F DP-115 Grease Seal (Radial) G DP-116 Grease Seal (Thrust) DP-125 Bearing Kit (Includes Items A-G) H DP-130 Bearing Housing I DP-131 Bearing Cover Plate J DP-132 Pump Support K DP-133 Shaft Collar M DP-134 Lantern Ring N DP-135 Stator Support P DP-137 Pin Retainer (Rotor Band) Q DP-138 Retaining Screw Washer R DP-139 Connecting Rod Washer Frame 4 Design Pumps (cont.) S DP-140 Connecting Rod TR DP-141 Rotor Pin TS DP-142 Shaft Pin U DP-143 Drive Pin Retaining Screw DP-150 Connecting Rod Kit (Items Q-U) V DP-155 Suction Housing W DP-156 Reducer X DP-157 Drive Shaft Y DP-158 Packing Gland Z DP-159 Packing AA DP-160 Packing Washer FF Rotors DP-165 2L Rotor DP-170 3L Rotor EE Stators DP-175 2L Stator, CDQ DP-180 3L Stator, CDQ DP-181 3L Stator, CDR DP-190 Grit Seal Assembly (Not Shown) 10 10.4
Pumps and Parts MOYNO Item Part Description Item Part Description Frame 6 Design Pumps 2L DP-200 Pump, Complete Assembly 3L DP-205 Pump, Complete Assembly A DP-210 Ball Bearing (Radial) B DP-211 Ball Bearing (Thrust) C DP-212 Bearing Spacer D DP-213 Bearing Lock Nut E DP-214 Bearing Lock Washer F DP-215 Grease Seal (Radial) G DP-216 Grease Seal (Thrust) DP-225 Bearing Kit (Includes Items A-G) H DP-230 Bearing Housing I DP-231 Bearing Cover Plate J DP-232 Pump Support K DP-233 Shaft Collar M DP-234 Lantern Ring N DP-235 Stator Support P DP-237 Pin Retainer (Rotor Band) Q DP-238 Retaining Screw Washer R DP-239 Connecting Rod Washer S DP-240 Connecting Rod Frame 6 Design Pumps (cont.) TR DP-241 Rotor Pin TS DP-242 Shaft Pin U DP-243 Drive Pin Retaining Screw DP-250 Connecting Rod Kit (Items Q-U) V DP-255 Suction Housing W DP-256 Reducer X DP-257 Drive Shaft Y DP-258 Packing Gland Z DP-259 Packing AA DP-260 Packing Washer FF Rotors DP-265 2L Rotor DP-270 3L Rotor EE Stators DP-275 2L Stator, CDQ DP-276 2L Stator, CDR DP-280 3L Stator, CDQ DP-281 3L Stator, CDR DP-290 Grit Seal Assembly (Not Shown) 10 Item Part Description Frame 8 Design Pumps 2L DP-300 Pump, Complete Assembly 3L DP-305 Pump, Complete Assembly A DP-310 Ball Bearing (Radial) B DP-311 Ball Bearing (Thrust) C DP-312 Bearing Spacer D DP-313 Bearing Lock Nut E DP-314 Bearing Lock Washer F DP-315 Grease Seal (Radial) G DP-316 Grease Seal (Thrust) DP-325 Bearing Kit (Includes Items A-G) H DP-330 Bearing Housing I DP-331 Bearing Cover Plate J DP-332 Pump Support K DP-333 Shaft Collar M DP-334 Lantern Ring N DP-335 Stator Support P DP-337 Pin Retainer (Rotor Band) Q DP-338 Retaining Screw Washer R DP-339 Connecting Rod Washer S DP-340 Connecting Rod Item Part Description Frame 8 Design Pumps (cont.) TR DP-341 Rotor Pin TS DP-342 Shaft Pin U DP-343 Drive Pin Retaining Screw DP-350 Connecting Rod Kit (Items Q-U) V DP-355 Suction Housing W DP-356 Reducer X DP-357 Drive Shaft Y DP-358 Packing Gland Z DP-359 Packing AA DP-360 Packing Washer FF Rotors DP-365 2L Rotor DP-370 3L Rotor EE Stators DP-375 2L Stator, CDQ DP-376 2L Stator, CDR DP-380 3L Stator, CDQ DP-381 3L Stator, CDR DP-390 Grit Seal Assembly (Not Shown) 10.5
Pump Parts Bean 26 16 15 14 35 9 3 6 7 13 12 2 4 12 4 3 13 24 25 18 29 22 32 31 32 33 34 21 20 26 27 37 1 36 30 63 19 8 11 14 15 10 5 16 17 18 62 61 60 20 21 23 17 38 10 59 39 47 38 41 40 46 43 42 45 44 57 58 55 56 10.6
Pumps Parts Bean Item No. Req d Part Description Item No. Req d Part Description 10 535 and 835 Pumping Units 1 1 79105 Pump Case 2 1 79328 Crankshaft 3 3 75077 Connecting Rod 4 3 Pair 75033 Bearing Insert 5 3 75032 Bushing, Connecting Rod 6 6 78547 Bolt Connecting Rod 7 6 79199 Nut 1/2-20 Elas. Stop 8 3 75072 Crosshead & Rod Ass. 9 6 Coml. Set Screw 5/16-18x5/16 10 3 75076 Wrist Pin 11 3 79327 O Ring, 5/8 ODx1/16 12 2 79121 Cone Bearing 13 2 79120 Cup Bearing 14 2 75044 Gasket 15? 79113 Shim 16 2 79114 Housing, Crankshaft Bearing 17 12 79107 Capscrew, Hex. Hd. 1/2-13 UNCx1 1/4 in. Lg. 18 18 Coml. Capscrew, Hex. Hd. 1/2-13 UNCx1 3/4 in. Lg. 19 1 79116 Pinion Shaft 20 2 75081 Ball Bearing 21 2 75043 Gasket 22 1 79109 Cap. Bearing 23 1 79108 Cap, Pinion Bearing 24 1 75045 Gasket, Cover 25 1 79123 Cover, Plate 26 1 79098 Petcock 27 1 NA Plate, Model 28 2 Coml. Screw, #4x3/16 in. Lg. 29 1 NA Inspection Plate 30 3 Coml. Lube Fitting, 1/8 C/Z 535 and 835 Pumping Units (cont.) 31 3 79748 Washer, Packing 32 6 79321 Seal, Oil 33 3 79320 Sleeve, Packing Nut 34 3 79326 Nut, Plunger Rod 35 1 79081 Cap, Oil 36 2 79112 Plug, 1/2 Pipe, Magnetic 37 6 75041 Stud, Lg. 5/8 in. Dia. 38 6 75070 Gasket Cylinder 39 3 79103 Cylinder, Ceramic, Steel Backed 40 3 75037 Holder, 2 3/4 in. Packing 41 3 79606 Plunger Cup 42 3 75062 Washer 43 3 75012 Nut, Plunger 44 3 75027 Nut, Special 45 1 79325 Valve Chamber 46 6 79324 Valve Seat, Ball 47 6 26157 Ball, 1 1/8 in. Dia. 54 3 75071 Gasket Cylinder Head 55 3 79460 Cylinder Cover 56 3 79101 Clamp Cylinder Head 57 2 75042 Stud 58 8 75054 Nut, Hex 5/8-11 UNC 59 3 75069 Gasket Valve Cover 60 3 75034 Valve Cover 61 3 78541 Clamp, Valve Cover 62 6 75022 Stud, 1/2x3 1/4 in. Lg. 63 6 75052 Nut, Hex. 1/2-13 UNC 64 2 28097 Pipe Plug, 1 1/2 in. 65 1 75050 Pipe Plug, 1 1/4 in. 66 1 75019 Remover, Plunger Cup 67 1 79333 Remover, Valve Seat Spare Parts Kit #A36686 NOTE: Pump Illustration with item no.s on next page. Part Description Part Description Common 520 Pump Spare Parts 75004 Plunger Cup Packing 79324 Valve Seat-Stainless Steel 21837 Valve Ball-Stainless Steel 79066 Steel Backed Ceramic Cylinder 79788 Valve Cover Gasket-Copper 75067 Valve Cover Gasket-Fiber 79789 Cylinder Head Gasket-Copper 75068 Cylinder Head Gasket-Fiber 79787 Cylinder Gasket-Copper 75066 Cylinder Gasket-Fiber Common 535 Pump Spare Parts 75001 Plunger Cup Packing 79324 Valve Seat (New Style) 1 1/2 in. O.D. 75040 Valve Seat (Old Style) 1 3/8 in. O.D. 26157 Valve Ball Stainless Steel 79103 Steel Backed Ceramic Cylinder 75069 Valve Cover Gasket-Copper 79334 Valve Cover Gasket-Fiber 75071 Cylinder Head Gasket-Copper 79323 Cylinder Head Gasket-Fiber 75070 Cylinder Gasket-Copper 79322 Cylinder Gasket-Fiber 10.7
Conventional & Wireline Packers 11
Packers Wireline Item Part Description No. Req d. NQ Wireline Packer Type II 1-14 48215 NQ Packer Assembly Type II 1 1 44018 Shakle 1 2 44017 Riser Tube 1 3 48218 Inflation Tube Jumper 1 4 44004 Adapter 1 5 44040 Fixed Head 1 6 44013 O-Ring 4 7 44005 Gland Element 2 8 48220 Center Tube 1 9 48222 Union Ring 2 10 48221 Gland Union 1 11 44012 Seal 2 12 44033 Sliding Head 1 13 44034 Plug 1 14 44007 Connector 1 11 HQ Wireline Packer Type II 1-14 48228 HQ Packer Assembly Type II 1 1 44018 Shakle 1 2 48239 Riser Tube 1 3 48218 Inflation Tube Jumper 1 4 44004 Adapter 1 5 48230 Fixed Head 1 6 48231 O-Ring 4 7 48232 Gland Element 2 8 48233 Center Tube 1 9 48235 Union Ring 2 10 48234 Gland Union 1 11 48237 Seal 2 12 48236 Sliding Head 1 13 44034 Plug 1 14 48238 Connector 1 PQ Wireline Packer Type II 1-14 51409 PQ Packer Assembly Type II 1 1 44018 Shakle 1 2 51423 Riser Tube 1 3 48218 Inflation Tube Jumper 1 4 44004 Adapter 1 5 51414 Fixed Head 1 6 51415 O-Ring 4 7 51416 Gland Element 2 8 51417 Center Tube 1 9 51419 Union Ring 2 10 51418 Gland Union 1 11 51421 Seal 2 12 51420 Sliding Head 1 13 44034 Plug 1 14 51422 Connector 1 11.1
Packers Conventional The groundwater monitoring packer is a low pressure, fixed-end style packer constructed of inert materials. It is available for two inch and larger casing and is designed for use above or below airlift, bladder, electric or piston sampling pumps to reduce purge time and volume. For isolating a specific test zone in a well, multiple groundwater monitoring packers can be used with a sampling pump. Applications: Groundwater monitoring Methane gas control/collection in landfills and mines Monitoring formation pressures Vacuum sampling under leachate pads Vadose zone sampling and injection Features: Constructed of Type 316 stainless steel and Viton or Viton clad gland element Can be inflated either pneumatically or hydraulically Able to withstand 200psi internal pressure Can be set at water level to prevent water intrusion during vacuum sampling Can be set up with transducer access tubes Multiple packers can be inflated simultaneously or separately Variety of through tubes and threaded end fittings available Ideal for portable or dedicated systems Custom designed systems for your specific site requirements Accessories: 1/8 in., 3/16 in., or 1/4 in. Nylon inflation tubes Stainless steel cable and eye bolts for lowering Nitrogen regulators 11 *Viton is a registered trademark of E.I. DuPont. Part No. Description Conventional Groundwater Monitoring Packers TT8321 1 Packer, 1.8-3.5 in. x 24 in. TT9249 2 Packer, 2.3-4.25 in. x 24 in. TT9365 3 Packer, 3.0-6.0 in. x 24 in. *Other sizes available upon request 11.2
THIS PAGE INTENTIONALLY LEFT BLANK
Grouters 12
Grouters Chemgrout CG-550 Workhorse Series A simple, field proven, highly-productive system for a wide range of grouting jobs. One operator system with a 45-gallon (170 liter) mixing tank, large holding hopper and centrally-located controls allow a single operator to continously mix and pump at the same time. Rapidly mixes and pumps cement, bentonite, cement/bentonite, cement/sand and non-shrink packaged grouts. Output 8 gpm (31 lpm), 160 psi (11 Bar), optional 240 psi (16.5 Bar). Power options include air, hydraulic, electric/hydraulic, gas/hydraulic or diesel/hydraulic. CG-550 Skid-mounted, Self-contained 12 CG-555 Trailer-mounted, Self-contained 12.1 CG-550 Skid-mounted, External Powered
Bentonite Products 13
Bentonite Products CETCO 1 7 4 6 8 2 3 5 13 13.1 1 PureGold Grout PureGold Grout is a containment resistant, high solids bentonite grout, used in place of cement to seal the annulus of monitoring wells. PureGold Grout has a moderate ph and will not affect ambient groundwater chemistry. T-21740 Volclay, Grout 1 Step, 50# Bag T-21750 Volclay, Grout 2, 50# Bag T-21900 Pure Gold Grout 2 Volclay Crumbles Volclay Crumbles are composed of high swelling, course (8 mesh) granular bentonite, free of fines. It is used to seal well casing, to decommission abandoned boreholes and to stop circulation loss during drilling. 2176 Crumbles, 50# Bag 3 PureGold Tablets PureGold Tablets are additive free, high swelling bentonite which is compressed into 1/4 in., 3/8 in. and 1/2 in. sizes. Resistant to a large spectrum of contaminants, the tablets are used to form a low permeable seal between the gravel pack and grout column in monitoring wells, to decommission abandoned boreholes and to seal the annulus in monitoring wells. T-21710 GEO Pellets, 1/2 50# Pail T-21714 GEO Pellets, 3/8 50# Pail T-21712 GEO Pellets, 1/4 50# Pail 4 PureGold Gel PureGold Gel is an organic and polymer free, 90 bbl. yield, intreated high quality bentonite drilling fluid. It is used in environmental rotary drilling where ambient groundwater quality and soil chemistry must be maintained. T-21890 Pure Gold Gel 5 PureGold Lube PureGold Lube is a bentonite based tool joint lubricant used in environmental drilling, when petroleum based lubricants are not allowed. 6 Super Gel-X Super Gel-X is an easy-mixing, high viscosity, 200 bbl. yield, fresh water drilling fluid. Produced from the highest grade Wyoming sodium bentonite, it delivers superior performance. T-21720 Super Gel X, 50# Bag 7 PureGold Chips PureGold Chips are matural sodium bentonite screened to 1/4 in. to 3/8 in. in size. They are used to seal between the gravel pack and grout column in monitoring wells, decommission geotechnical boreholes and abondoned wells. T-21910 Pure Gold Chips, Med. 8 Versa Foam A biodegradable foaming agent for fresh or salt water, air rotary or percussion drilling, it improves penetration rate and lifting capacity. Versa Foam s high stability keeps cutting suspended. T-21720 Super Gel X, 50# Bag 9 Coated Bentonite Pellets TR-30 1/4 in. and 3/8 in., time release *Picture not shown
Bentonite Products Baroid AquaGuard Grout AquaGel Gold Seal Benseal Casing Seal EZ-Mud Having the right mud products in stock, and knowing how to properly use them are two different things. At Boart Longyear, our drilling specialists know how to specify and use all of Baroid s mud products. They ve been trained to help you solve your drilling problems in the most cost-effective and efficient ways possible. You can depend on Boart Longyear to have the right product in stock and the technical expertise to know how to use it. Now, that s extra value for your drilling dollar. We Service You Nationwide, From A Single Pallet, To Truck Load Quantities. With seven stocking locations around the U.S., we re never very far from where you are. And for greater convenience, we deliver direct to yourjob site in selected areas. each one of stocking locations carries a wide range of Baroid mud products to meet virtually all of your drilling requirements. So...whether it s environmental drilling, water well, horizontal, remediation, or minerals exploration, you can depend on Boart Longyear for your Baroid mud products. Baroid Product AQUAGEL GOLD SEAL AQUA-GROUT & trade: AQUAGUARD & trade: BARAFOAM BARAFOS BAROID BAROID BENTONITE PELLETS BENSEAL BENSEAL EX MUD BIO-BORE & trade: BORE-GEL & trade: CASING SEAL & trade: CON DET CORE-LUBE & trade: DRIL-FOAM ENVIRO-TORO EZ MUD EZ MUD PLUS EZ MUD DP HOLE PLUG LIQUI-TROL & trade: POLY-BORE & trade: QUIK-FOAM QUIK-GEL QUIK-GROUT & trade: QUIK-TROL & trade: SHUR-GEL COATED PELLETS Environmental Drilling Water Well Drilling Horizontal Drilling Development & Remediation Minerals Exploration 13 13.2
THIS PAGE INTENTIONALLY LEFT BLANK
Well Protection Products 14
Monitoring Well Protection Lockable Stand-Up Galvanized Well Covers Boart Longyear lockable, stand-up Well Covers provide rugged protection while hinged covers allow easy access to wells. The original square shape indexes the Well Cover so it cannot be rotated out of the concrete pad. The raised lid allows the wellcasing to rise above the edge of the cover when opened for easier accessibility. Convenient tabs enable covers to be securely locked with a single padlock. A full-width hinge secures cover in place. Part Description Lockable Stand-Up Galvanized Well Covers TC-200 TC-400 TC-600 4 in. x 4 in. x 5 in. Well Cover, Galvanized 6 in. x 6 in. x 5 in. Well Cover, Galvanized 8 in. x 8 in. x 5 in. Well Cover, Galvanized Cast Iron Manholes With Sheet Metal Skirts Boart Longyear Leak-Resistant Manholes provide H-20 traffic-rating and help protect against water infiltration for monitoring wells completed at-grade. The lids are painted white with a black monitoring well triangle and are clearly marked Monitoring well. Manholes utilize a Buna-N gasket that expands as the bolts are tightened, forming a leak resistant seal. A 9/16 inch rachet or wrench is used to gain access to the well. The manholes feature a galvanized skirt construction. Now available in an economic seven inch design for smaller applications. Applicable Standards: RR-F-621E, ASTM A48, AASHTO H-20, Part Description Cast Iron Manholes With Sheet Metal Skirts 300123 7 in. I.D. (unpainted), Leak resistant, 2 bolt TC-239P 7 in. I.D. (painted), Leak resistant, 2 bolt TC-240 8 in. I.D. (unpainted),12 in. Skirt,Leak resistant TC-240P 8 in. I.D. (painted), w/ 12 in. Skirt, Leak resistant, 3 bolt TC-241P 8 in. I.D. (painted), w/ 8 in. Skirt, Leak resistant, 3 bolt TC-246P 12 in. I.D. (painted), w/ 12 in. Skirt, Leak resistant, 2 bolt 14 Cast Iron Manhole With HDPE Skirt Economical yet durable, this manhole features a Heavy-duty cast iron (ASTM A-48 Class 30 or better) upper assembly. Certified by an independent laboratory to meet H-20 roadway loading. Lightweight, durable, corrosion and hydrocarbon-resistant High Density Polyethylene (HDPE) plastic skirt, painted lid with monitor well triangle. Buna-NO rubber gasket set into collar insures water-tight seal with pressure fit. High quality stainless steel bolts set into gasketed washers maintain water-tight seal. Foundry insert provides option for custom lettering. Part Description Cast Iron Manhole With HDPE Skirt 4001408 8 in. x 12 in. Well Cover w/ HDPE Skirt 4583189 8 in. x 8 in. Well Cover w/ HDPE Skirt Accessories 4583190 Wrench 14.1
Monitoring Well Protection Aluminum Leak Resistant Manhole Water-tight cover bunan gasket 1/2 in. Teflon coated bolts to secure cover E-cips on bolts used to lift cover when evenly backing bolts out Solid construction H-20 plus traffic rating Meets Wisconsin and Indiana Departments of Natural Resources requirements and Minnesota Department of Health requirements. Part Description Aluminum Leak Resistant Manhole TC-250 8.2 in. I.D., 10 in. O.D., 12.375 in. tall, ship wt. 17 lbs. 48 per pallet Welded, Seemless Manhole The 418xAW is the newest model of the Limited Access Style Manhole. The unique features offered in this manhole include continusously welded seams on skirt assembly and ring-to-skirt assembly. A heavy gage, steel skirt and four steel lugs welded to the skirt, provide anchoring to the oncrete slab. This manhole is painted and has a black monitoring triangle on the bolt-down lid. H-20 traffic rating meets Wisconsin Departments of Natural Resources requirements. Part Description Welded, Seemless Manhole MON0345 9 in. Manhole w/ 12 in. Skirt, HD design w/ placement anchor lugs MON0350 12 in. Manhole w/ 12 in. Skirt, HD design w/ placement anchor lugs 14 14.2
Monitoring Well Protection Galvanized Steel Body Well Plugs Part Description TC102 2 in. Watertight Locking Plug w/ Lock (Cherne Orange Type) TC10210 2 in. Watertight Locking Plug w/o Lock (Cherne Orange Type) TC104 4 in. Watertight Locking Plug w/ Lock (Cherne Orange Type) TC10410 4 in. Watertight Locking Plug w/o Lock (Cherne Orange Type) TC106 6 in. Watrertight Locking Plug w/o Lock (Cherne Orange Type) Brass Body Well Plugs Part Description 300022 2 in. Licking Plug w/ Lock 300117 4 in. Locking Plug w/o Lock Econo Well Plugs Part Description 4001456 2 in. Locking Plug w/o Lock (Cherne Yellow Type) 015556 4 in. Locking Plug w/o Lock (Cherne Yellow Type) 14 High Strength Plastic, Enviro Caps Part Description 300541 2 in. ENVIRO Cap 300542 4 in. ENVIRO Cap 300543 Keys for locking and unlocking 14.3
Bailers & Water Level Indicators 15
Bailers Disposable and Reusable Aqua Bailers disposable bailers are made with the highest regard to quality in the marketplace. The large open-top design allows nearly an inch of open space for easy tie-on. And the thick, sturdy construction gives you the added security you want when lowering bailers down your wells. A Double-check Valve Bailer (also known as a discrete sampler or point-source bailer) allows sampling of a specific depth by utilizing a check valve at both the top and bottom of the bailer. Polyethylene Bailers Diameters: 1.6 in., 0.75 in., 0.5 in. All assembled parts constructed of high-density polyethylene PVC ball in check-valve assembly 12 in., 36 in., 48 in., or custom lengths Unweighted, Weighted, Double-Weighted Single- or Double-Check Valve Teflon Bailers Diameters: 1.6 in., 0.75 in., 0.5 in. All assembled parts constructed of 100% virgin Teflon Teflon ball in check-valve assembly 12 in., 36 in., or custom lengths Unweighted, Weighted, Double-Weighted Single- or Double-Check Valve Part Description 15 Disposable Bailers TB-600 1.5 in. x 3 ft. Standard Disposable Bailer Case of 24 TB-602 1.5 in. x 3 ft. Weighted Disposable Bailer Case of 24 4581341.70 in. x 3 ft. Clear View Bailer Case of 30 4581340 1.5 in. x 3 ft. Clear Disposable PVC Bailer Case of 30 TB-606 1.5 in. x 3 ft. Clear Disposable Teflon Bailer Case of 12 TB-606 1.5 in. x 1 ft. Clear Disposable Teflon Bailer Case of 12 300480 Bailer, Stainless Steel 5/8 in. ODx3 ft. 15.1
Item No. November 1, 2001 Water Level Indicator The Slope Indicator/Water Level Indicator is a portable and accurate instrument that measures water levels in wells and standpipes. The unit features a sturdy aluminum cable reel, plyurethane cable, and a 3/8 inch diameter stainless steel sensor. Built into the cable reel are a light, a buzzer and a battery test switch. As the sensor is lowered down the well, the light and buzzer indicate when contact with the water table is made. Permanetly stamped depth markings on the cable show the water level. Features: Cable markings in hundredths of a foot An eyelet on the sensor tip for easy attachment of a weight Also available with Tefzel coated tape Metric cable markings are also available Applicable Standards: ASTM 4750 Description Water Level Indicators SI51690010 SI51690015 SI51690030 Water Level Indicator 100 ft Water Level Indicator 150 ft Water Level Indicator 300 ft Water Level Indicators Slope Indicator 15 15.2
THIS PAGE INTENTIONALLY LEFT BLANK
PVC 16
Monitor Well Construction Materials PVC TriLoc and ASTM F 480 (2 tpi) Features: Small diameter PVC screens, pipe and fittings 2 in. PVC slotted screens, pipe and fittings 4 in. PVC slotted screens, pipe and fittings Large diameter PVC slotted screen, pipe and fittings CircumSlot screen 2 tpi (ASTM F 480) ASTM Thread Easy start Quick to make up TriLoc Thread Tight thread Leakproof to 325 psi 4 tpi (ASTM F 480) We offer two alternatives in PVC thread profiles: 2 or 4 threads per inch (tpi). Both threads fully comply with ASTM F 480. 16 16.1
Monitor Well Construction Materials PVC Part Description Part Description TriLoc PVC 4 tpi (unless specified) TL.75-150 PVC, 3/4 in. x 5 ft. Riser S/40 TL.75-200 PVC, 3/4 in. x 10 ft. Triloc Pipe TL.75-350 PVC, 3/4 in. Male Cap S/40 TL.75-400 PVC, 3/4 in. Female Plugs S/40 TLS.75-151 PVC, 3/4 in. x 5 ft. Screen.010 TLS.75-152 PVC, 3/4 in. x 5 ft. Screen.020 TLS.75-201 PVC, 3/4 in. x 10 ft. Screen.010 TLS.75-202 PVC, 3/4 in. x 10 ft. Screen.020 TL1-150 PVC, 1 in. x 5 ft. Pipe S/40 8TPI TL1-200 PVC, 1 in. x 10 ft. Pipe 8TPI TL1-150 PVC, 1 in. x 5 ft. Pipe S/40 8TPI TL1-200 PVC, 1 in. x 10 ft. Pipe 8TPI TL1-300 PVC, 1 in. Threaded Cap TL1-400 PVC, 1 in. Female Plug TL1-150 PVC, 1 in. x 5 ft. Pipe S/40 8TPI TLS1-151 PVC, 1 in. x 5 ft. Triloc Screen.010 8TPI S/40 TLS1-152 PVC, 1 in. x 5 ft. Triloc Screen.020 8TPI S/40 TLS1-201 PVC, 1 in. x 10 ft. Triloc Screen.010 TLS1-202 PVC, 1 in. x 10 ft. Triloc Screen.020 TL1.25-150 PVC, 1-1/4 in. x 5 ft. Triloc Riser 8TPI TL1.25-200 PVC, 1-1/4 in. x 10 ft. Threaded Pipe 8TPI TL1.25-350 PVC, 1-1/4 in. Threaded Cap TL1.25-400 Female Plug TLS1.25-151 PVC, 1-1/4 in. x 5 ft. Screen.010 8TPI TLS1.25-152 PVC, 1-1/4 in. x 5 ft. Screen.020 8TPI TLS1.25-201 PVC, 1-1/4 in. x 10 ft. Screen.010 8TPI TLS1.25-202 PVC, 1-1/4 in. x 10 ft. Screen.020 8TPI TL2-100 PVC, 2 in. x 2-1/2 ft. Threaded Pipe TL2-150 PVC, 2 in. x 5 ft. Threaded Pipe TL2-100 PVC, 2 in. x 2-1/2 ft. Threaded Pipe TL2-200 PVC, 2 in. x 10 ft. Triloc Pipe TL2-350 PVC, 2 in. Threaded Male Cap, Top TL2-400 PVC, 2 in. Female Threaded Plug, Bottom TLS2-101 PVC, 2 in. x 2-1/2 ft. Triloc Screen.010 TLS2-102 PVC, 2 in. x 2-1/2 ft. Triloc Screen.020 TLS2-151 PVC, 2 in. x 5 ft. Triloc Screen.010 TLS2-152 PVC, 2 in. x 5 ft. Triloc Screen.020 TLS2-201 PVC, 2 in. x 10 ft. Triloc Screen.010 TLS2-202 PVC, 2 in. x 5 ft. Triloc Screen.020 TL4-100 PVC, 4 in. x 2-1/2 ft. Triloc Pipe TL4-150 PVC, 4 in. x 5 ft. Threaded Pipe TL4-200 PVC, 4 in. x 10 ft. Triloc Threaded Pipe TL4-350 PVC, 4 in. Male Threaded Top Cap TL4-400 PVC, 4 in. Female Bottom Plug TLS4-101 PVC, 4 in. x 2-1/2 ft. Triloc Screen.010 TLS4-102 PVC, 4 in. x 2-1/2 ft. Triloc Screen.020 TLS4-151 PVC, 4 in. x 5 ft. Triloc Screen.010 TLS4-152 PVC, 4 in. x 5 ft. Triloc Screen.020 TLS4-201 PVC, 4 in. x 10 ft. Triloc Screen.010 TLS4-202 PVC, 4 in. x 10 ft. Triloc Screen.020 TL6-150 PVC, 6 in. x 5 ft. Triloc Pipe TL6-200 PVC, 6 in. x 10 ft. Triloc Threaded Pipe TL6-350 PVC, 6 in. Male Threaded Top Cap TL6-400 PVC, 6 in. Female Threaded Bottom Plug TLS6-151 PVC, 6 in. x 5 ft. Triloc Screen.010 TLS6-152 PVC, 6 in. x 5 ft. Triloc Screen.020 TLS6-201 PVC, 6 in. x 10 ft. Triloc Screen.010 TLS6-202 PVC, 6 in. x 10 ft. Triloc Screen.020 16 16.2
Monitor Well Construction Materials PVC Part Description Part Description ASTM 480 Thread PVC A2-100 PVC, 2 in. x 2-1/2 ft. ASTM Riser S/40 A2-150 PVC, 2 in. x 5 ft. ASTM Riser S/40 A2-200 PVC, 2 in. x 10 ft. ASTM Riser S/40 A2-350 PVC, 2 in. ASTM Cap S/40 A2-400 PVC, 2 in. ASTM Plug S/40 AS2-101 PVC, 2 in. x 2-1/2 ft. ASTM Screen.010 AS2-102 PVC, 2 in. x 2-1/2 ft. ASTM Screen.020 AS2-151 PVC, 2 in. x 5 ft. ASTM Screen.010 AS2-152 PVC, 2 in. x 5 ft. ASTM Screen.020 AS2-201 PVC, 2 in. x 10 ft. ASTM Screen.010 AS2-202 PVC, 2 in. x 10 ft. ASTM Screen.020 TCM-151 PVC, 2 in. x 5 ft. ASTM Circumslot.010 TCM-152 PVC, 2 in. x 5 ft. ASTM Circumslot.020 TCM-201 PVC, 2 in. x 10 ft. ASTM Circumslot.010 TCM-202 PVC, 2 in. x 10 ft. ASTM Circumslot.020 A4-100 PVC, 4 in. x 2-1/2 ft. ASTM Riser S/40 A4-150 PVC, 4 in. x 5 ft. ASTM Riser S/40 A4-200 PVC, 4 in. x 10 ft. ASTM Riser S/40 A4-350 PVC, 4 in. ASTM Cap S/40 A4-400 PVC, 4 in. ASTM Plug S/40 AS4-101 PVC, 4 in. x 2-1/2 ft. ASTM Screen.010 AS4-102 PVC, 4 in. x 2-1/2 ft. ASTM Screen.020 AS4-151 PVC, 4 in. x 5 ft. ASTM Screen.010 AS4-152 PVC, 4 in. x 5 ft. ASTM Screen.020 AS4-201 PVC, 4 in. x 10 ft. ASTM Screen.010 AS4-202 PVC, 4 in. x 10 ft. ASTM Screen.020 A6-150 PVC, 6 in. x 5 ft. ASTM Riser A6-200 PVC, 6 in. x 10 ft. ASTM Riser A6-350 PVC, 6 in. ASTM Cap A6-400 PVC, 6 in. ASTM Plug AS6-151 PVC, 6 in. x 5 ft. ASTM Screen.010 AS6-152 PVC, 6 in. x 5 ft. ASTM Screen.020 AS6-201 PVC, 6 in. x 10 ft. ASTM Screen.010 AS6-202 PVC, 6 in. x 10 ft. ASTM Screen.020 A8-150 PVC, 8 in. x 5 ft. ASTM Threaded Pipe S/40 A8-200 PVC, 8 in. x 10 ft. ASTM Threaded Pipe S/40 A8-350 PVC, 8 in. ASTM Male Cap S/40 A8-400 PVC, 8 in. ASTM Plug AS8-152 PVC, 8 in. x 5 ft. ASTM Screen.020 AS8-202 PVC, 8 in. x 10 ft. ASTM Screen.020 16 16.3
Monitor Well Construction Materials CircumSlot Boart Longyear Circumslot is a single piece extrusion well screen that is internally ribbed to permit circumferential slotting. This special slotting provides maximum strength and uniform material composition. This higher open area means maximum ability for fluids to enter the well casing. The uniform distribution of openings enables total formation development and allows stratified fluids to enter the well. Circumslot is an excellent choice for low yielding formations to enhance sample retrieval when monitor wells recover slowly. It provideshigher, less restrictive flow into product recovery remeiation wells where maximum fluid retrieval is desired. Flush threaded joints mate directly with TriLoc pipe or 2 TPI pipe; integral threads won t pull off. Circumslot screen and all Boart Longyear PVC pipe meets ASTM F 480 standard. Fully Circumferential Slots Allows complete access to well formation. Uniform distribution of openings allows complete well development and more accurate sampling. Lower head flow into the screen. Increased Open Area Full 360 slot provides same open area as wire-wound and more than double that of conventional slotted screen. Allows complete non-segregated flow. Single Piece Extrusion An integral TriLoc flush-thread joint means no thread pull-off. Seamless construction and uniform material composition mean greater strength. Available in TriLoc or 2 TPI thread design. Cost Savings CircumSlot can provide a more cost effective well construction material as more open area means faster well development and reduced purging time. Open area is comparable to wire wrapped screen, at a greatly reduced cost. Overall cost of your monitoring or recovery program is reduced. Increased Inside Diameter The 4 in. and 6 in. CircumSlot are custom extruded to provide a true 4 in. and 6 in. ID, allowing easier equipment installation. 2 in. CircumSlot has a 1.75 in. ID. Part Circumslot Description TCS-151 PVC, 2 in. x 5 ft. Circumslot.010 TCS-152 PVC, 2 in. x 5 ft. Circumslot.020 TCS-201 PVC, 2 in. x 10 ft. Circumslot.010 TCS-202 PVC, 2 in. x 10 ft. Circumslot.020 TCS-451 PVC, 4 in. x 5 ft. Circumslot.010 TCS-452 PVC, 4 in. x 5 ft. Circumslot.020 TCS-401 PVC, 4 in. x 10 ft. Circumslot.010 TCS-402 PVC, 4 in. x 10 ft. Circumslot.020 TCM-651 PVC, 6 in. x 5 ft. ASTM Circumslot.010 TCM-652 PVC, 6 in. x 5 ft. ASTM Circumslot.020 TCM-601 PVC, 6 in. x 10 ft. ASTM Circumslot.010 TCM-602 PVC, 6 in. x 5 ft. ASTM Circumslot.020 TLS6-651 PVC, 6 in. x 5 ft. Circumslot.010 TLS6-652 PVC, 6 in. x 5 ft. Circumslot.020 TLS6-601 PVC, 6 in. x 10 ft. Circumslot.010 TLS6-602 PVC, 6 in. x 10 ft. Circumslot.020 16 16.4
THIS PAGE INTENTIONALLY LEFT BLANK
Stainless Steel 17
Monitor Well Construction Materials Stainless Steel Part Description ASTM (2 TPI) Stainless Steel, 304 Pipe and screen, Schedule #5 Midbody and Schedule 40 Ends SAS2-151 2x5 SST Wire Wrapped Screen,.010 SAS2-152 2x5 SST Wire Wrapped Screen,.020 SAS2-201 2x10 SST Wire Wrapped Screen,.010 SAS2-202 2x10 SST Wire Wrapped Screen,.020 SA2-100 2 in. x 2.5 ft. SST Monitor Pipe SA2-150 2 in. x 5 ft. SST Monitor Pipe SA2-200 2 in. x 10 ft. SST Monitor Pipe SA2-400 2 in. Bottom Plug ASTM (2 TPI) Stainless Steel, 304 Pipe and screen, Schedule #5 Midbody and Schedule 40 Ends SAS4-151 4x5 SST Wire Wrapped Screen,.010 SAS4-152 4x5 SST Wire Wrapped Screen,.020 SAS4-201 4x10 SST Wire Wrapped Screen,.010 SAS4-202 4x10 SST Wire Wrapped Screen,.020 SA4-100 4 in. x 2.5 ft. SST Monitor Pipe SA4-150 4 in. x 5 ft. SST Monitor Pipe SA4-200 4 in. x 10 ft. SST Monitor Pipe SA4-400 4 in. Bottom Plug 17 Other sizes, s/s 316, and midbody thickness available upon request. 17.1
Dimensions & Conversions 18
Field Facts Monitor Well VOLUME OF SCHEDULE 40 PVC PIPE Diameter 1.25 in. 2 in. 3 in. 4 in. 6 in. 8 in. 12 in. OD 1.66 in. 2.375 in. 3.5 in. 4.5 in. 6.625 in. 8.625 in. 12.75 in. ID 1.38 in. 2.067 in. 3.068 in. 4.026 in. 6.065 in. 7.981 in. 11.938 in. Volume Gal/Linear Ft. 0.08 0.17 0.38 0.66 1.5 2.6 5.81 Weight of Water Lbs/Linear Ft. 0.64 1.45 3.2 5.51 12.5 21.65 48.44 Hole Diameter (inches) 7.25 7.25 7.25 8.25 10.25 8.25 10.25 12.25 8.25 10.25 12.25 12.25 VOLUME OF OPEN BOREHOLE AND ANNULUS BETWEEN CASING AND HOLE Volume per Lineal Ft. Gal. 2.14 2.14 2.45 2.78 4.29 2.78 4.29 6.13 2.78 4.29 6.13 6.13 Cu. Ft. 0.29 0.29 0.33 0.37 0.57 0.37 0.57 0.82 0.37 0.57 0.82 0.82 Nominal Casing Diameter (inches) 1.25 2 2 2 2 3 3 3 4 4 4 6 Volume per Lineal Ft. Gal. 2.03 1.91 2.22 2.55 4.06 2.28 3.79 5.62 1.95 3.46 5.3 4.33 WEIGHTS AND DIMENSIONS Cu. Ft. 0.27 0.26 0.3 0.34 0.54 0.3 0.51 0.75 0.26 0.46 0.71 0.58 Lb. Sand per Linear Ft. of Annulus 27 26 30 34 54 30 51 75 26 46 71 58 Lb. 0.5 in. Pellets per Lineal Ft. of Annulus 21 20 23 26 41 23 38 57 20 35 54 44 Pipe Size 1.25 in. 2 in. 4 in. 6 in. 8 in. Pipe Size 2 in. 4 in. Pipe OD 1.666 2.375 4.5 6.25 8.625 Pipe OD 2.375 4.5 Pipe ID 1.38 2.067 4.026 6.065 7.981 Pipe ID 1.939 3.826 Approx. Ship Wt. 0.43 lb/ft. 0.70 lb/ft. 2.0 lb/ft. 3.45 lb/ft. 5.22 lb/ft. Approx. Ship Wt. 0.93 lb/ft. 2.70 lb/ft. Rows of Slots 3 3 6 8 10 Rows of Slots 3 6 Pipe Size 2 in. 4 in. 6 in. Pipe Size 2 in. 4 in. Pipe Size 2 in. 4 in. Pipe OD 2.375 4.5 6.635 Pipe OD 2.375 4.5 Pipe OD 2.375 4.5 Pipe ID 1.875 3.89 5.688 Pipe ID 2.067 4.026 Pipe ID 1.8 3.985 Approx. Ship Wt. 0.80 lb/ft. 1.7 lb/ft. 3.7 lb/ft. Approx. Ship Wt. 1.7 lb/ft. 4.0 lb/ft. Approx. Ship Wt. 4.0 lb/ft. 6.0 lb/ft. 18 18.1
Field Facts Monitor Well INTAKE AREA SLOTTED SCREEN (0.125 in. spacing - PVC) Slot Size 2 in. 4 in. 0.01 2 in. 4 in. 0.012 2.82 5.63 0.01 2.82 5.634 0.016 3.67 7.34 0.02 4.43 8.86 0.024 5.18 10.36 0.028 5.9 11.79 0.03 6.24 12.47 0.032 6.57 13.13 0.04 6.57 13.13 0.05 6.57 13.13 SLOTTED SCREEN (0.25 in. spacing - PVC) 2 in. 4 in. 6 in. 8 in. Slot Size 2 in. 4 in. 2 in. 4 in. 6 in. 8 in. 0.006 1.46 2.92 3.89 4.86 0.008 1.46 2.92 3.89 4.86 0.01 6.8 11.3 1.94 3.89 5.18 6.48 0.012 2.38 4.75 6.34 7.92 0.015 2.79 5.57 7.43 9.29 CIRCUMSLOT (PVC) 0.02 12.8 21.2 3.25 6.5 8.67 10.84 0.025 3.4 6.8 9.07 11.34 0.03 17.9 30.0 3.63 7.26 9.86 12.1 0.035 4.43 8.86 11.81 14.76 0.04 22.4 37.7 5.4 10.8 14.4 18 0.05 WIRE-WOUND SCREEN (Stainless Steel) Slot Size 2 in. 4 in. 0.006 8.4 16.1 0.008 10.6 20.9 0.01 12.9 25.5 0.012 15.2 29.7 0.015 18.1 35.5 0.02 22.6 44.2 0.025 26.8 51.9 0.03 30.3 59 0.035 33.5 65.5 0.04 36.5 70.9 0.05 41.3 80.6 MISCELLANEOUS DATA (approximations) 1 cubic foot = 7.5 gallons 1 gallon = 0.134 cubic foot 1 cubic yard = 202 gallons 1 gallon = 0.005 cubic yard 1 gallon of water = 8.34 lbs. 1 barrel = 42 gallons 1 cubic foot of fresh water = 62.4 lbs. PSI 0.434 x the height of the water column in ft. Feet of head = PSI x 2.304 1 sack of sand = 1 cubic foot and weighs 100 lbs. 1 sack of cement = 1 cubic foot and weighs 96 lbs. 1 pail of Bentonite pellets = 50 lbs. 18 18.2
Dimensions Drill Rods and Casing Drill Rods Size OD (in) ID (in) Coupling ID (in) Weight (lb/10ft) Threads per in Content (US gal/100ft) AW* 1 3/4 1 7/32 5/8 44 3 6.0 BW 2 1/8 1 3/4 3/4 42 3 12.5 NW 2 5/8 2 1/4 1 3/8 54 3 20.7 HW 3 1/2 3 1/16 2 3/8 85 3 38.3 *Parallel Wall Size OD (in) Rod Body (in) Tool Joint ID (in) Weight (lb/10ft) Threads per in Content (US gal/100ft) AWJ 1 3/4 1 3/8 5/8 32 5 7.4 AWJ L/W 1 3/4 1 1/2 5/8 22.7 5 9 BWJ 2 1/8 1 3/4 3/4 40.4 5 12.3 NWJ 2 5/8 2 1/4 1 1/8 52 4 20 Flush-Joint Casing Size OD (in) ID (in) Weight (lb/10ft) Threads per in Content (US gal/100ft) AW 2 1/4 1 29/32 38 4 14.8 BW 2 7/8 2 3/8 70 4 23 NW 3 1/2 3 86 4 36.7 HW 4 1/2 4 113 4 65.2 PW 5 1/2 5 144 3 102 Wireline Drill Rods and Q Wireline Drill Rods Size OD (in) ID (in) Weight (lb/10ft) Threads per in Content (US gal/100ft) AQ 1 3/4 1 3/8 31 4 7.7 BQ 2 3/16 1 13/16 40 3 13.4 NQ 2 3/4 2 3/8 52 3 23 HQ 3 1/2 3 1/16 77 3 38.2 PQ 4 5/8 4 1/16 108 3 71.5 Diamond Coring Drill Bits and Q Wireline Diamond Bits Size Core Diameter (in) Hole Diameter (in) Hole volume (US gal/100ft) Decimal Fraction Decimal Fraction AQ, AQ-U 1.062 1 1/16 1.890 1 57/64 14.6 AQTK, AQTK-U 1.202 1 13/64 1.890 1 57/64 14.6 BQ, BQ-U 1.432 1 7/16 2.360 2 23/64 22.7 BQTK, BQTK-U 1.601 1 39/64 2.360 2 23/64 22.7 NQ, NQ-U 1.875 1 7/8 2.980 2 63/64 36.3 NQ2 1.990 2 2.980 2 63/64 33.6 HQ, HQ-U 2.500 2 1/2 3.782 3 25/32 58.3 PQ 3.345 3 11/32 4.827 4 53/64 95.1 BQ-3 1.320 1 5/16 2.360 2 23/64 22.7 NQ-3 1.775 1 25/32 2.980 2 63/64 36.3 HQ-3 2.406 2 13/32 3.782 3 25/32 58.3 PQ-3 3.270 3 9/32 4.827 4 53/64 95.1 Other Diamond Coring Bits Size Core Diameter (in) Hole Diameter (in) Hole volume (US gal/100ft) Decimal Fraction Decimal Fraction 18 18.3 RWG 0.735 47/64 1.175 1 11/64 5.6 EWG, EWM, EWL 0.845 27/32 1.485 1 31/64 9 AWG, AWM, AWL 1.185 1 3/16 1.890 1 57/64 14.6 BWG, BWM, BWL 1.655 1 21/32 2.360 2 23/64 22.7 NWG, NWM, NWL 2.155 2 5/32 2.980 2 63/64 36.3 HWG 3.000 3 3.907 3 29/32 62.3 2 3/4 x 3 7/8 2.690 2 11/16 3.875 3 7/8 61.2 4 x 5 1/2 3.970 3 31/32 5.495 5 1/2 123.4 4 x 7 3/4 5.970 5 31/32 7.750 7 3/4 245.1 NOTE: All dimensions, weights and volumes shown are nominal
Conversions square inch (in 2 ) x 645.160 = square millimeter (mm 2 ) x 0.00155 = square inch (in 2 ) square inch (in 2 ) x 6.452 = square centimeter (cm 2 ) x 0.155 = square inch (in 2 ) square feet (ft 2 ) x 0.093 = square meter (m 2 ) x 10.764 = square feet (ft 2 ) pound-force (lbf) x 4.448 = Newton (N) x 0.225 = pound-force (lbf) Kilogram-force (kgf) x 9.807 = Newton (N) x 0.102 = kilogram-force (kgf) inch (in) x 25.4 = millimeter (mm) x 0.039 = inch (in) foot (ft) x 0.305 = meter (m) x 3.281 = foot (ft) mile (mi) x 1.609 = kilometer (km) x 0.621 = mile (mi) pound (lb) x 0.454 = kilogram (kg) x 2.205 = pound (lb) ounce (oz) x 28.350 = gram (g) x 0.0353 = ounce (oz) pound-force foot (lbf ft) x 1.356 = Newton meter (Nm) x 0.738 = pound-force foot (lbf ft) pound-force inch (lbf in) x 0.113 = Newton meter (Nm) x 8.851 = pound-force inch (lbf in) horsepower (hp) x 0.746 = kilowatt (kw) x 1.341 = horsepower (hp) Kilowatt hour (kwh) x 3,600,000 = joule (j) x 0.00000278 = kilowatt hour (kwh) pound per square inch (psi) x 6.895 = kilo pascal (kpa) x 0.145 = pound per square inch (psi) pound per square inch (psi) x 0.00689 = mega pascal (MPa) x 145.03 = pound per square inch (psi) inch of water (in H 2 O) @ 60 F x 248.830 = Newton per square meter (N/m 2 ) x 0.00402 = inch of water (in H 2 O) @ 60 F degree Fahrenheit ( F) -32 x 0.556 = degree Celcius ( C) x 1.8 + 32 = degree Fahrenheit ( F) -32 feet per second (ft/sec) x 0.305 = meter per second (m/sec) x 3.281 = feet per second (ft/sec) miles per hour (mph) x 1.609 = kilometer per hour (km/h) x 0.621 = miles per hour (mph) U.S. gallon (U.S. gal.) x 3.785 = litre (l or L) x 0.264 = U.S. gallon (U.S. gal.) Imperial gallon (Imp. gal.) x 4.544 = litre (l or L) x 0.2196 = Imperial gallon (Imp. gal.) cubic inch (in 3 ) x 16.387 = cubic centimeter (cm 3 ) x 0.061 = cubic inch (in 3 ) cubic inch (in 3 ) x 0.0164 = liter (l or L) x 61.02 = cubic inch (in 3 ) cubic feet (ft 3 ) x 0.0283 = cubic meter (m 3 ) x 35.315 = cubic feet (ft 3 ) U.S. gallon per minute (gpm) x 3.785 = litre per minute (L/min) x 0.264 = U.S. gallon per minute (gpm) cubic feet per minute (cfm) x 0.0283 = cubic meter per minute (m 3 /min) x 35.315 = cubic feet per minute (cfm) 18 18.4
THIS PAGE INTENTIONALLY LEFT BLANK
Terms 19
Terms 19 19.1 1. Exclusion of Warranties BOART MAKES NO WARRANTY THAT THE PRODUCTS SOLD HEREUNDER SHALL BE MERCHANTABLE OR THAT SUCH PRODUCTS SHALL BE FIT FOR ANY PARTICULAR PURPOSE AND THERE ARE NO WARRANTIES EXPRESS OR IMPLIED MADE BY BOART EXCEPT ITS FOLLOWING STANDARD WARRANTY: Boart warrants each new and unused product manufactured at its Stone Mountain, Georgia factory be free from defects in material and workmanship under normal use and service for 90 days from date of delivery to buyer. The obligation under this warranty being limited to the replacement or repair at the Boart factory, or at a point designated by it, of such parts as shall appear to it upon inspection at such point to have defective in material or workmanship at the time sold, provided that the parts claimed defective are returned to inspection point, transportation charges prepaid. This warranty applies only to new and unused products which after shipment from the Boart factory have not been altered, changed or repaired in any manner. 2. Exclusion of Liability for Consequential Damage It is further agreed by the purchaser that in no event shall Boart be liable for increased costs, loss of profit or goodwill or any special, indirect, incidental, or consequential damages whatsoever arising out of any breach by Boart. 3. Delivery Boart shall not be liable for any delays in manufacturing or delivering any of the merchandise hereunder, or for any damage or loss to purchaser arising therefrom, if such delay shall be due to one or more of the following causes: fire; destruction of plant; strike; lockout; dispute with workman; epidemic; flood; accident; delay in transportation; war (whether declared or undeclared); insurrection; riot; blockade; embargo; acts, demands or requirements of the United States, or of any state or territory thereof, or of any governmental subdivision of any thereof, restraining orders or decrees of any court or judge; or any other cause whatsoever, whether similar or dissimilar to those hereinbefore enumerated, beyond the reasonable control of Boart; and the existence of any such cause or causes of delay shall extend the time of performance by the time or times measured by any such cause or causes of delay. If delivery is not completed within 60 days after the date stipulated in the acceptance of the order due to any of said causes, either Boart of the Buyer may cancel this contract on 10 days notice to the order. If delivery of the merchandise is delayed in transit due to default in payment of purchase price, or to delay in receipt of shipping instructions, document for payment, required inspection, export permit or other cause for which Boart is not responsible, charges for demurrage and storage shall be paid by the Buyer. Any goods delivered, any manner of delivery, or any matter not directly disputed shall be paid for by the Buyer, notwithstanding that other goods or methods or times of delivery might be disputed by the Buyer. 4. Taxes The sales price stipulated in this contract does not include any sales, use, excise, or other tax. If any such tax is imposed by law on the Buyer on account of this sale and Boart is obligated to collect and pay such tax, the amount of such tax paid by Boart shall be reimbursed to it by the Buyer forthwith in addition to the purchase price. 5. Title and Risk Loss Title to, ownership, and right to possession of the merchandise sold by this contract, and risk of loss, shall pass to the Buyer at the time of delivery to the carrier or Buyer, whichever first occurs. Provided that if payment of the purchase price is not contemporaneous with, or does not precede delivery to carrier or Buyer, delivery may be conditioned by Boart upon prompt execution and delivery of such documentation as it deems necessary or appropriate, including without limitation execution of such security agreements, and Uniform Commercial Code financing statements and such other documents as are appropriate to perfect its security interest in the goods delivered, or upon execution of a conditional sales contract containing such provisions as Boart deems appropriate to protect its interest, and reserving title until payment of the full purchase price. 6. Claims By Buyer Claims for any shortage or defects shall be deemed and released unless such claim is made in writing to Boart within seven days after receipt of the shipment, except for defects covered by the warranty in paragraph 1 above, which shall be made in writing within seven days after discovery thereof. 7. Terms Terms of sale are net 30 days less any cash discount as stated on the invoice for established customers. New accounts must provide bank reference as well as three trade references. A check or money order for payment in full or shipment on a C.O.D. basis will be allowed while credit is being established. Buyer agrees to pay Boart finance charges at the rate of 1.5% per month on past due accounts. Visa/Mastercard purchases are now being accepted at the Stone Mountain location. 8. Price Prices, published under separate cover, are subject to change at an time without notice. Boart reserves the right to correct price list or billing errors as they are discovered. Orders calling for future delivery will be billed according to the price in effect at the time of delivery. Prices are f.o.b. shipping point. Normal mode of shipment will be UPS unless otherwise specified by Buyer or Boart. Buyer agrees to pay all freight charges. 9. Acceptance of Offer to Sell Ordering products from the Boart catalog constitutes an acceptance of the offer to sell made by the catalog and is subject to all the conditions stated herein. No Boart distributor, sales representative, or field agent has the authority to modify the terms of the offer and has no authority to contract for or bind Boart. Acceptance of the offer made by the catalog is valid only upon the receipt of such acceptance by Boart at its principal office in Stone Mountain, GA and not upon delivery to a Boart distributor, sales representative or field agent.
Terms This publication is provided as is without warranty of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability, fitness for a particular purpose, or non-infringement. This publication could include technical inaccuracies or typographical errors. Changes are periodically added to information herein; these changeswill be incorporated in new editions of the publication. Boart Longyear Company is constantly striving to improve its products and reserves the right to change design, materials, specifications and price without notice. Q, Triloc, Circumslot and Boart Longyear Company are registered trademarks of the Boart Longyear Company. Stinger Bit is a registered trademark of Foremost Mobil Company, Inc. Slope Indicator is a registered trademark of Slope Indicator Company. Ridgid is a registered trademark of the Ridgid Tool Company. Lynac is a registered trademark of the Acker Drill Company. King is a registered trademark of King Oil Tool, Inc. Moyno is a registered trademark of Moyno, Inc. Bean is a registered trademark of FMC Corporation. Chemgrout is a registered trademark of Chemgrout, Inc. Cetco is a registered trademark of the Colloid Environmental Technologies Company. Baroid is a registered trademark of Baroid Drilling Fluids, Inc. All other trademarks or service marks are the property of their respective owners. 19 19.2
Boart Longyear Locations California 970 Garcia Avenue Pittsburg, CA 94565 Tel: 925/439-5377 800/828-9436 Fax: 925/439-8451 Georgia 2200 Centre Park Court P.O. Box 1959 Stone Mountain, GA 30086-1959 Tel: 770/469-2720 800/241-9468 Fax: 770/879-6488 800/833-7018 Minnesota 147 North Jonathon Boulevard Chaska, MN 55318 Tel: 612/448-2277 800/336-1995 Fax: 612/448-2969 Pennsylvania 60 Leigh Drive York, PA 17402 Tel: 717/767-6977 800/233-1943 Fax: 717/764-1716 Wisconsin 3802 West Stewart Avenue Wausau, WI 54401 Tel: 715/842-3276 800/876-6690 Fax: 715/848-8213 800/472-1527 2001 Boart Longyear Company. Boart Longyear is constantly striving to improve its products and must, therefore, reserve the right to change designs, materials, specifications, and prices without notice Ref: 2/01. Printed in U.S.A. Boart Longyear Company 2640 West 1700 South Salt Lake City, Utah 84104 USA Telephone: +1-801-972-6430 1-800-453-8740 Fax: +1-801-977-3373 E-mail: sales@boartlongyear.com Web site: www.boartlongyear.com Canada P.O. Box 330, 1111 Main Street West North Bay, Ontario, Canada P1B 8H6 Tel: (705) 474-2800 or (800) 461-7333 Fax: (705) 474-2373 Web site: www.boartlongyear.com Printed on recycled paper with soy ink.