Rotary Cutter RC4610 & RCM4610 39299 334-144P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2018 Printed 07/11/18 Cover photo may show optional equipment not supplied with standard unit.
Table of Contents Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Section 2: Decks & Hitches...6 Blade Carrier...6 Deck Center Components...8 Deck Center Drive Components...10 Deck Wing Components...12 Deck Wing Drive Components...14 Hitch A-Frame...16 Hitch Ball Coupler...18 Hitch Bar Tite...20 Hitch LP Performance...22 Hitch Pintel...24 Hitch Standard Pivoting Clevis...26 Leveling Rod...28 Off Center Lights 3 Inch (LED)...30 Splitter Box Sliding Cover...32 Weight Box...34 Section 3: Axles...36 Axle Center...36 Axle Wing...38 Hub Assembly (330-938K)...40 Rotary Cutter Tire Options...42 Section 4: Guards...44 Chain Guards Front Double...44 Chain Guards Front Single...46 Chain Guards Rear Double...48 Chain Guards Rear Single...50 Section 5: Drivelines...52 Driveline Center (826-818C) Comer...52 Driveline CV 38 1000 RPM (826-644C) Weasler...54 Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler...56 Driveline CV 75 1000 RPM (826-645C)...58 Driveline CV 540 RPM (826-643C) Weasler...60 Driveline Wing (826-811C) Comer...62 Driveline Wing (826-812C) Comer...64 Section 6: Gearboxes...66 Gearbox (826-721C)...66 Gearbox 1000 RPM (826-319C)...68 Gearbox 1000 RPM (826-725C)...70 Gearbox 540 RPM (826-650C)...72 Gearbox Divider 1000 RPM (826-521C) Comer...74 Gearbox Divider 1000 RPM (826-521C) ITG...76 Gearbox Divider 540 RPM (826-520C) Comer...78 Gearbox Divider 540 RPM (826-520C) ITG...80 Section 7: Hydraulics...82 Hydraulic Components...82 Hydraulic Cylinder (810-312C) Cross...84 Hydraulic Cylinder (810-312C) Lion...86 Hydraulic Cylinder (810-312C) Midway...88 Hydraulic Cylinder (810-624C) Midway...90 Hydraulic Cylinder (810-624C) Red Lion...92 Section 8: Options & Accessories...94 Manual Winch Wing Deck...94 Off Center Lights 3 Inch (LED) Retro-Fit (334-579A)...96 Section 9: Decals...98 Decals...98 Touch-up Paints...100...102 Copyright 2018. All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Alphabetized Table of Contents A B C D G H L Axle Center...36 Axle Wing...38 Blade Carrier...6 Chain Guards Front Double...44 Chain Guards Front Single...46 Chain Guards Rear Double...48 Chain Guards Rear Single...50 Decals...98 Deck Center Components...8 Deck Center Drive Components...10 Deck Wing Components...12 Deck Wing Drive Components...14 Driveline Center (826-818C) Comer...52 Driveline CV 38 1000 RPM (826-644C) Weasler...54 Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler...56 Driveline CV 75 1000 RPM (826-645C)...58 Driveline CV 540 RPM (826-643C) Weasler...60 Driveline Wing (826-811C) Comer...62 Driveline Wing (826-812C) Comer...64 Gearbox (826-721C)...66 Gearbox 1000 RPM (826-319C)...68 Gearbox 1000 RPM (826-725C)...70 Gearbox 540 RPM (826-650C)...72 Gearbox Divider 1000 RPM (826-521C) Comer...74 Gearbox Divider 1000 RPM (826-521C) ITG...76 Gearbox Divider 540 RPM (826-520C) Comer...78 Gearbox Divider 540 RPM (826-520C) ITG...80 Hitch A-Frame...16 Hitch Ball Coupler...18 Hitch Bar Tite...20 Hitch LP Performance...22 Hitch Pintel...24 Hitch Standard Pivoting Clevis...26 Hub Assembly (330-938K)...40 Hydraulic Components...82 Hydraulic Cylinder (810-312C) Cross...84 Hydraulic Cylinder (810-312C) Lion...86 Hydraulic Cylinder (810-312C) Midway...88 Hydraulic Cylinder (810-624C) Midway...90 Hydraulic Cylinder (810-624C) Red Lion...92 Touch-up Paints...100 Leveling Rod...28 M O R S W Manual Winch Wing Deck...94 Off Center Lights 3 Inch (LED)...30 Off Center Lights 3 Inch (LED) Retro-Fit (334-579A)...96 Rotary Cutter Tire Options...42 Splitter Box Sliding Cover...32 Weight Box...34 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 3
4 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 5
Blade Carrier Table of Contents Section 2: Decks & Hitches 39089 6 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Section 2: Decks & Hitches Blade Carrier Table of Contents Ref. Part No. Part Description Comments Revision 5. 5. 5. 5. 6. Dwg 39089 326-430H 802-277C 803-170C 804-147C 820-138C 820-194C 820-137C 820-193C 318-586A Image No. DISHPAN 15 CENTERS W/HVY HUB BLD BLT 1 1/8-12X44 W/.25KEY NUT HEX TOP LOCK 1 1/8-12 PLT WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X31 CCW CUTTER BLADE 1/2X4X31 LL CCW CUTTER BLADE 1/2X4X25 CCW CUTTER BLADE 1/2X4X25 LL CCW BLADE BOLT KIT Center deck (standard) Center deck (low lift) good for tall weeds and brush Wing deck (standard) Wing deck (low lift) good for tall weeds and brush 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 7
Deck Center Components Section 2: Decks & Hitches 39300 8 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Deck Center Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. Dwg 39300 318-211H 318-212H 331-187D 331-615H 331-615H81 331-615H82 331-615H83 331-615H86 331-616H 331-616H81 331-616H82 331-616H83 331-616H86 802-015C 802-214C 803-169C 803-198C 840-273C Image No. WLDMT. SKID SHOE RH. WLDMT. SKID SHOE LH. RH FRONT DEFLECTOR CENTER DECK WO/DR CENTER DECK WO/DR GREEN CENTER DECK WO/DR ORANGE CENTER DECK WO/DR RED CENTER DECK WO/DR, YELLOW CENTER DECK W/DR CENTER DECK W/DR GREEN CENTER DECK W/DR ORANGE CENTER DECK W/DR RED CENTER DECK W/DR, YELLOW RHSNB 3/8-16X1 GR5 RHSNB 1/2-13X1 1/4 GR5 NUT HEX FLG LOCK 1/2-13 PLT NUT HEX WHIZ 3/8-16 PLT PLUG LP 3" ID RUBBER Beige Green Orange Red Yellow Beige Green Orange Red Yellow 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 9
Deck Center Drive Components Section 2: Decks & Hitches 39301 10 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Deck Center Drive Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. 28. 29. 29. 29. 29. 30. 30. 3 3 3 Dwg 39301 318-141H 318-920S 331-121D 331-552V 331-555S 331-632H 331-633H 801-248C 802-005C 802-007C 802-053C 802-057C 802-138C 802-383C 802-967C 803-255C 803-263C 803-299C 804-007C 804-009C 804-010C 804-016C 804-022C 804-034C 816-481C 817-455C 826-818C 826-520C 826-521C 826-643C 826-644C 826-645C 826-793C 826-650C 826-725C 837-066C 837-076C 842-243C Image No. WLDMT. SHAFT PROTECTOR MANUAL STORAGE CONTAINER KIT SPLITTER OFFSET PANEL SLIDING SHIELD ASSY, 50 GB GEARBOX BEARING BLOCK MNT SLIDING SHIELD SPLITTER MNT 46 FRONT SPLITTER SHIELD RC4615 PAN HD 1/4-20X3/4 PHILLIPS SS HHCS 1/4-20X1 GR5 HHCS 5/16-18X3/4 GR5 HHCS 5/8-11X1 3/4 GR5 HHCS 5/8-11X2 1/4 GR5 HHCS 5/16-18X2 1/4 GR5 HHCS 3/4-10X3 GR5 HHCS M8X25X35 GR8.8 NUT HEX NYLOCK 1/4-20 NUT HEX FLANGE LOCK 5/8-11 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER FLAT 1/4 SAE PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT WASHER FLAT 1/2 SAE PLT WASHER LOCK SPRING 5/8 PLT WASHER FLAT 1/4 SAE SS MANUAL STORAGE CONTAINER KNOB 1/2-13 MALE THD 2 3/8OD DRVLN C4 11 75-20 FX CLTCH DIV BOX 540RPM 1 3/4-20 DIV BOX 1000RPM 1 3/4-20 DRVLN C6 42 38-6 CV DRVLN C6 42 38-21 CV DRVLN C6 47 75-20 CV DRVLN C6 39 38-21 CV ORCLTCH GBOX RC50 1:60 STD GBOX RC50 15:1 STD DRIVELINE SHIELD CONE, 2 PIECE SHIELD SPACER HHCS M8X25X20 GR8.8 THD-LCK Only used with ITG divider box Only used with ITG divider box Only used with ITG divider box Only used with ITG divider box RC4610 ITG and Comer RCM4610 ITG And Comer RC4610 RCM4610 RCM4610 RCM4610 RC4610 RCM4610 Only used with ITG divider box 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 11
Deck Wing Components Section 2: Decks & Hitches 39302 12 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Deck Wing Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 Dwg 39302 330-068D 330-504H 331-684H 331-684H81 331-684H82 331-684H83 331-684H86 331-685H 331-685H81 331-685H82 331-685H83 331-685H86 331-792H 802-022C 802-155C 802-466C 803-014C 803-198C 804-013C 840-273C 330-505L Image No. DEFLECTOR RH HINGE ROD DECK RH WING WO/DR DECK RH WING WO/DR GREEN DECK RH WING WO/DR ORANGE DECK RH WING WO/DR RED DECK RH WING WO/DR, YELLOW DECK RH WING W/DR DECK RH WING W/DR GREEN DECK RH WING W/DR ORANGE DECK RH WING W/DR RED DECK RH WING W/DR, YELLOW BEVELED SKID SHOE RH HHCS 3/8-16X1 1/2 GR5 RHSNB 3/8-16X1 1/4 GR5 PLOW 3/8-16X1 1/4 GR5 NUT HEX 3/8-16 PLT NUT HEX WHIZ 3/8-16 PLT WASHER LOCK SPRING 3/8 PLT PLUG LP 3" ID RUBBER ASSY HINGE ROD Beige Green Orange Red Yellow Beige Green Orange Red Yellow 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 13
Deck Wing Drive Components Section 2: Decks & Hitches 39303 14 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Deck Wing Drive Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 7. 8. 8. 9. 10. Dwg 39303 326-922D 802-383C 803-299C 804-009C 804-010C 826-486C 826-811C 826-812C 826-721C 826-319C 837-066C 842-243C Image No. GB MOUNT PLATE HHCS 3/4-10X3 GR5 NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT COMER U0.125.70000 DIPSTICK DRVLN C4 50 75-20 FX CLTCH DRVLN C5 48 75-20 FX CLTCH GBOX RC50 1:60 REV GBOX RCM50 1:21 REV DRIVELINE SHIELD CONE, 2 PIECE HHCS M8X25X20 GR8.8 THD-LCK 540 RPM 1000 RPM 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 15
Hitch A-Frame Table of Contents Section 2: Decks & Hitches 37649 16 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Section 2: Decks & Hitches Hitch A-Frame Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 Dwg 37649 331-087D 331-088D 331-089D 331-561H 331-629H 800-001C 802-096C 802-106C 802-155C 802-235C 803-014C 803-020C 803-031C 803-168C 804-011C 804-013C 804-015C 804-027C 804-028C 890-182C N\A 891-524C Image No. PTO HANGER BUSHING PTO HANGER STOP PTO HANGER ADJUSTABLE JACK MOUNT HITCH W/ ADJ JACK MNT GREASE ZERK STRAIGHT 1/4-28 HHCS 1-8X2 1/2 GR5 RHSNB 1/2-13X1 1/2 GR5 RHSNB 3/8-16X1 1/4 GR5 HHCS 1-8X5 GR5 NUT HEX 3/8-16 PLT NUT HEX 1/2-13 PLT NUT HEX 1-8 PLT NUT HEX TOP LOCK 1-8 PLT WASHER FLAT 3/8 USS PLT WASHER LOCK SPRING 3/8 PLT WASHER LOCK SPRING 1/2 PLT WASHER LOCK SPRING 1 PLT WASHER FLAT 1 USS PLT SAFETY CHAIN 10000 LB SIDEWIND JACK 7000 LB Available with sidewind jack 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 17
Hitch Ball Coupler Table of Contents Section 2: Decks & Hitches 26568 18 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hitch Ball Coupler Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg 26568 330-335A 330-348H 802-053C 803-304C Drawing Image Number 2 5/16" BALL HITCH ASSEMBLY * 2 5/16" BALL HITCH WELDMENT HHCS 5/8-11X1 3/4 GR5 NUT HEX WHIZ 5/8-11 PLT For 2-5/16" Ball 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 19
Hitch Bar Tite Table of Contents Section 2: Decks & Hitches 26569 20 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Section 2: Decks & Hitches Hitch Bar Tite Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 Dwg 26569 330-333A 318-358H 318-834H 330-271H 330-563D 330-564D 330-975H 800-001C 802-053C 802-070C 802-074C 802-205C 803-168C 803-181C 803-258C 803-301C 803-304C 804-025C 804-028C 804-171C 805-105C 890-862C 330-974K Drawing Image Number BAR TITE HITCH * SHAFT WELDMENT WELDMENT HITCH CLEVIS SWIVEL RECEIVER HITCH WEAR PLATE WIDE FORMED HITCH SUPPORT WIDE BAR TITE WIDE TOP GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 HHCS 3/4-10X6 GR5 HHCS 1-8X6 1/2 GR5 HHCS 1-8X5 1/2 GR5 NUT HEX TOP LOCK 1-8 PLT NUT HEX FLANGE LOCK 3/4-10 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 USS PLT WASHER FLAT 50 HARD ASTMF436 PIN COTTER 1/4 X 2 1/2 PLT BUSHING 50ODX00IDX25 BAR TITE HITCH WIDE 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 21
Hitch LP Performance Section 2: Decks & Hitches 39286 22 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hitch LP Performance Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. Dwg 39286 334-045A * 330-271H 331-543D 334-046H 334-048H 800-001C 802-053C 802-075C 802-079C 803-201C 803-258C 803-301C 803-304C 804-013C 804-171C 805-105C 890-836C 890-850C Image No. LP PERFORMANCE HITCH SWIVEL RECEIVER HITCH HOLDER HITCH CLEVIS HITCH YOKE GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X7 GR5 HHCS 3/8-16X1 1/4 GR5 NUT HEX COUPLER 3/8-16X1 3/4 NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 50 HARD ASTMF436 PIN COTTER 1/4 X 2 1/2 PLT BUSHING 1 1/4X1X1/2 HRD BUSHING 1 1/4X1X5/8 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 23
Hitch Pintel Table of Contents Section 2: Decks & Hitches 27673 24 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Section 2: Decks & Hitches Hitch Pintel Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. Dwg 27673 330-501A 330-499H 802-053C 802-729C 803-304C 803-304C 890-806C Drawing Image Number PINTLE HITCH * PINTLE RECEIVER HHCS 5/8-11X1 3/4 GR5 HFS 5/8-11X2 1/2 GR8 PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 5/8-11 PLT PINTLE HOOK SQ.BASE BDB1250-15 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 25
Hitch Standard Pivoting Clevis Section 2: Decks & Hitches 27672 26 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hitch Standard Pivoting Clevis Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. Dwg 27672 330-498A 330-163D 330-497H 330-500H 802-053C 802-110C 802-356C 803-024C 803-258C 803-304C Drawing Image Number STANDARD HITCH * SPACER HITCH CLEVIS WELDMENT YOKE HITCH 3615 HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X9 GR5 HHCS 5/8-11X8 1/2 GR5 NUT LOCK 5/8-11 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX WHIZ 5/8-11 PLT 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 27
Leveling Rod Table of Contents Section 2: Decks & Hitches 39304 28 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Section 2: Decks & Hitches Leveling Rod Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. Dwg 39304 318-008H 330-470H 330-471K 803-075C 803-265C 804-025C 805-083C 805-109C Image No. WLDMT. LEVEL ROD SHORT LEVEL ROD LONG LEVEL ROD NUT HEX JAM 7/8-9 NUT HEX COUPLER 7/8-9X5 WASHER FLAT 3/4 SAE PLT PIN CLVS.75X50 USBL HT PIN COTTER 1/8 X 1 1/4 PLT 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 29
Off Center Lights 3 Inch (LED) Section 2: Decks & Hitches 39037 30 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Off Center Lights 3 Inch (LED) Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 1 1 1 1 1 1 15. 16. 17. 18. Dwg 39037 334-496L 331-682A 330-965D 330-966D 330-967D 800-060C 802-015C 802-027C 802-224C 803-078C 803-209C 803-255C 804-007C 891-522C J-37-R J-37-A J-AC1-15-B 891-523C J-37-R J-37-A J-AC1-15-B 891-529C 891-530C 891-531C 891-532C 891-534C Image No. OFFSET CUTTER LIGHT KIT 3" OFFSET CUTTER LIGHT KIT 3" * LIGHT MNT LIGHT GUARD LIGHT MNT CLAMP CABLE TIE.19X125 3DIA 50LB RHSNB 3/8-16X1 GR5 HHCS 3/8-16X4 1/2 GR5 HHCS 1/4-20X1 1/4 GR5 NUT LOCK 3/8-16 NYLON INSERT NUT FLANGE LOCK 3/8-16 PLT NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT DUAL LED LIGHT LH RED LED LENS MODULE AMBER LED LENS MODULE BLACK LENS COVER DUAL LED LIGHT RH RED LED LENS MODULE AMBER LED LENS MODULE BLACK LENS COVER LIGHT WIRE HARNESS 8' RPBY 891-529C ENHANCE MODULE LEAD WIRE HARNESS 8' LIGHT MAGNETS WITH HARDWARE S/N 1150618+ Lights are now standard S/N 1150617- Lights were optional Complete light assembly Red lens Amber lens Black lens Complete light assembly Red lens Amber lens Black lens Obsolete 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 31
Splitter Box Sliding Cover Section 2: Decks & Hitches 37650 32 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Splitter Box Sliding Cover Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. Dwg 37650 331-076D 331-552V 331-554H 331-555S 801-248C 802-301C 802-843C 803-255C 804-006C 804-009C 804-010C 804-034C 817-936C 842-243C 891-485C 891-487C J200UM-01-10.4 Image No. SLIDING SHIELD SLIDING SHIELD ASSY, 50 GB SLIDING SHIELD GB MNT, 50/60GB GEARBOX BEARING BLOCK MNT PAN HD 1/4-20X3/4 PHILLIPS SS HHCS 1/4-20X1/2 GR5 HHCS M6X1X20 18-8 SS NUT HEX NYLOCK 1/4-20 WASHER LOCK SPRING 1/4 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT WASHER FLAT 1/4 SAE SS HANDLE GRAB 4 1/8WIDE1 1/2TALL HHCS M8X25X20 GR8.8 THD-LCK WS-10 GUIDE RAIL FLOATING ZINC BEARING BLOCK REPLACEMENT LINER With Liners 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 33
Weight Box Table of Contents Section 2: Decks & Hitches 39305 34 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Section 2: Decks & Hitches Weight Box Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 9. 9. 9. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 Dwg 39305 318-923D 326-152D 326-224D 330-504H 330-505L 331-210D 331-257D 331-304D 334-117H 334-117H81 334-117H82 334-117H83 334-117H86 334-118K 334-127K 802-015C 802-022C 802-155C 802-368C 802-466C 803-014C 803-168C 803-198C 804-013C 890-341C 890-400C Image No. SKID SHOE WTBX ROUND ROD.25 X 14 ROUND ROD.25 X 16.50 HINGE ROD ASSY HINGE ROD FRONT WEIGHT BOX LOCK FRONT WEIGHT BOX CHAIN GUARD REAR WEIGHT BOX CHAIN GUARD WEIGHT BOX WEIGHT BOX, GREEN WEIGHT BOX, ORANGE WEIGHT BOX, RED WEIGHT BOX, YELLOW FRONT WEIGHT BOX CHAIN GUARD REAR WEIGHT BOX CHAIN GUARD RHSNB 3/8-16X1 GR5 HHCS 3/8-16X1 1/2 GR5 RHSNB 3/8-16X1 1/4 GR5 HHCS 1-8X3 GR5 PLOW 3/8-16X1 1/4 GR5 NUT HEX 3/8-16 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX WHIZ 3/8-16 PLT WASHER LOCK SPRING 3/8 PLT CHAIN WELD 5/16 GR 43 X 5 LINK CHAIN WELD 5/16 GR 43 X 4 LINK 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 35
Axle Center Table of Contents Section 3: Axles 37655 36 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Section 3: Axles Axle Center Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. Dwg 37655 330-607H 330-938K 331-099H 331-569H 800-001C 800-073C 802-082C 802-099C 802-110C 802-205C 803-019C 803-168C 803-169C 803-381C 804-016C 805-058C 807-271C 815-425C 891-177C Image No. PIVOT PIN TRAILING ARM HUB 5 BOLT COMPLETE TRAILING ARM CENTER CENTER AXLE GREASE ZERK STRAIGHT 1/4-28 GREASE ZERK 1/4-28 X 90-DEG HHCS 1/2-13X1 3/4 GR5 HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X9 GR5 HHCS 1-8X5 1/2 GR5 NUT LOCK 1/2-13 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX FLG LOCK 1/2-13 PLT NUT HEX JAM SLOTTED 1 1/4-7 WASHER FLAT 1/2 SAE PLT PIN COTTER 3/16 X 2 SPRING COMP 20OD.63W 5.5L SPINDLE, DUAL BOLT-ON 7/8-14 BHG 50ODX25X38 Used only on right hand side Used only on right hand side 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 37
Axle Wing Table of Contents Section 3: Axles 37656 38 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Section 3: Axles Axle Wing Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 Dwg 37656 330-608H 330-610S 330-938K 331-574H 331-575H 331-794H 331-795L 334-464H 334-466S 800-001C 800-073C 801-229C 802-082C 802-099C 802-357C 802-915C 803-019C 803-168C 803-169C 803-381C 804-016C 805-058C 807-271C 815-491C 891-177C Image No. PIVOT PIN TRAILING ARM WG ASY PIVOT PIN TRAIL ARM WG HUB 5 BOLT COMPLETE WING AXLE RH WING AXLE LH TRAILING ARM WING SPINDLE AND HUB ASSY WING TRAILING ARM PIVOT PIN WING TRAILING ARM PIV PIN ASY GREASE ZERK STRAIGHT 1/4-28 GREASE ZERK 1/4-28 X 90-DEG SCREW SLOTTED HEX 1/4-28X3/16 HHCS 1/2-13X1 3/4 GR5 HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X6 GR5 HHCS 1-8X5 GR8 PLT SPTHD NUT LOCK 1/2-13 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX FLG LOCK 1/2-13 PLT NUT HEX JAM SLOTTED 1 1/4-7 WASHER FLAT 1/2 SAE PLT PIN COTTER 3/16 X 2 SPRING COMP 20OD.63W 5.5L SINGLE AXLE SPINDLE, WING BHG 50ODX25X38 S/N 1081359- S/N 1081359- S/N 1081360+ S/N 1081360+ S/N 1081359- S/N 1081360+ 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 39
Hub Assembly (330-938K) Section 3: Axles 37676 40 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hub Assembly (330-938K) Section 3: Axles Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. Dwg 37676 200-001D 330-938K 800-080C 802-779C 803-029C 803-310C 804-055C 805-246C 815-243C 816-497C 822-020C 822-021C 822-033C 822-034C 815-242C Image No. HUB GREASE CAP HUB 5 BOLT COMPLETE GREASE ZERK 1/4-28 THD FORMING HUB STUD 1/2-20X88 GR5 NUT HEX SLOTTED 7/8-14 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG HUB 5-BOLT W/CUPS/STUDS SEAL 75ID CR17617 BRG CUP LM-67010 BRG CONE 25ID LM-67048 BRG CUP LM-48510 BRG CONE LM-48548 HUB 5-BOLT CASTING 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 41
Rotary Cutter Tire Options Section 3: Axles 37659 42 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Rotary Cutter Tire Options Section 3: Axles Ref. Part No. Part Description Comments Revision 5. 6. 7. Dwg 37659 814-265C 814-449C 814-450C 814-451C 814-461C 814-478C 814-480C Image No. TIRE & WHL LAM. 6X9X21(5-BOLT) TIRE, AC 29" 16 PLY 5 BOLT TIRE H29X9.0X15 USED TUBE FOR 29X9.0-15 RIM 2PC 5BLT 15X6.5 NEW TIRE FF 25.5X8-14 20PLY NEW TIRE 25.5X8-14 20PLY 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 43
Chain Guards Front Double Section 4: Guards 39312 44 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Chain Guards Front Double Section 4: Guards Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. Dwg 39312 334-126A 318-108D 318-336D 318-337D 318-876K 318-879K 330-474K 330-475K 331-441D 331-444D 331-445D 331-447D 802-015C 803-198C 890-175C 890-341C Image No. CHNGRD FRONT DOUBLE, OFFSET * ROUND ROD 1/4 X 36 ROUND ROD 1/4 X 73 ROUND ROD 1/4 X 25 ASSY. DUAL CHAINGUARD FRT.CTR ASSY.DUAL CHAINGUARD FRT.WING CHNGRD DBL FRT RH CHNGRD DBL FRT LH FRONT WING DOUBLE CHAINGUARD CHNGRD DBL FRT RH CHNGRD DBL FRT LH CHNGRD DBL FRT CNT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 GR 43 X 6 LINKS PLT CHAIN WELD 5/16 GR 43 X 5 LINK 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 45
Chain Guards Front Single Section 4: Guards 39311 46 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Chain Guards Front Single Section 4: Guards Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. Dwg 39311 334-125A 318-108D 318-223K 318-226K 318-264D 318-336D 330-472K 330-473K 331-440D 331-442D 331-443D 331-446D 802-015C 803-198C 890-175C 890-341C Image No. CHNGRD FRONT SINGLE, OFFSET * ROUND ROD 1/4 X 36 ASSY. CHAINGUARD FRT. CTR. ASSY. CHAINGUARD FRT. WING ROD 1/4 X 28 ROUND ROD 1/4 X 73 CHNGRD SGL FRT RH CHNGRD SGL FRT LH FRONT WING CHAINGUARD CHNGRD SGL FRT RH CHNGRD SGL FRT LH CHNGRD SGL FRT CNT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 GR 43 X 6 LINKS PLT CHAIN WELD 5/16 GR 43 X 5 LINK 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 47
Chain Guards Rear Double Section 4: Guards 39314 48 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Chain Guards Rear Double Section 4: Guards Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. Dwg 39314 334-129A 318-107D 318-641D 318-895D 330-119D 330-214K 330-477K 802-015C 803-198C 890-175C 890-393C Image No. CHNGRD REAR DOUBLE, OFFSET * ROUND ROD 1/4 X 31 1/2 ROUND ROD.25 X 9 CHNGRD REAR CNTR INNER DBL CHNGRD DBL REAR OUT CHNGRD CNTR REAR INNER DBL CHNGRD DBL REAR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 GR 43 X 6 LINKS PLT CHAIN WELD 5/16 GR 43 X 7-LINK 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 49
Chain Guards Rear Single Section 4: Guards 39313 50 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Chain Guards Rear Single Section 4: Guards Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. Dwg 39313 334-128A 318-107D 318-641D 318-876D 330-107D 330-208K 330-476K 802-015C 803-198C 890-175C 890-393C Image No. CHNGRD REAR SINGLE, OFFSET * ROUND ROD 1/4 X 31 1/2 ROUND ROD.25 X 9 BRACKET CHNGRD CNTR INNER CHNGRD SGL REAR OUT CHNGRD CNTR REAR INNER CHNGRD SGL REAR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 GR 43 X 6 LINKS PLT CHAIN WELD 5/16 GR 43 X 7-LINK 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 51
Driveline Center (826-818C) Comer Section 5: Drivelines 37510 52 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Driveline Center (826-818C) Comer Section 5: Drivelines Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. Dwg 37510 826-818C 14026.357.1 180.016.780 190.000.032 190.000.047 170.016.630.1 155.150.724 190.000.016 15016.896.1 146.26021 165.000.589 180.01022 15016.037.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 Image No. DRVLN C4 11 75-20 FX CLTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE CO INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 53
Driveline CV 38 1000 RPM (826-644C) Weasler Section 5: Drivelines Applies to RCM4610 37911 54 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Driveline CV 38 1000 RPM (826-644C) Weasler Section 5: Drivelines Applies to RCM4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. Dwg 37911 826-644C 26-15120 68810-1003 03-15570 26-16033 99-24406 19-15135 97-25023 96-24406 98-24406 03-15316 55051-1817 11-14988 11-15180 93-25023 92-24406 91-25023 Drawing Image Number DRVLN C6 42 38-21 CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 55
Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler Applies to RCM4610 Section 5: Drivelines 35997 56 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler Section 5: Drivelines Applies to RCM4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 Dwg 35997 826-793C 26-15120 68810-1003 03-15570 26-16033 99-24406 97-26654 19-15135 13-10021 13-10022 96-26654 98-26654 03-15316 39-10039 Drawing Image Number DRVLN C6 39 38-21 CV ORCLTCH * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE OUTER GUARD WE GUARD REPAIR KIT WE SAFETY SIGN WE SAFETY SIGN WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE OVERRUNNING THRST CLTCH ASM 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 57
Driveline CV 75 1000 RPM (826-645C) Section 5: Drivelines Applies to RCM4610 37912 58 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Driveline CV 75 1000 RPM (826-645C) Section 5: Drivelines Applies to RCM4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. Dwg 37912 826-645C 26-13387 68810-1005 03-15570 26-16033 99-24406 19-15135 97-25075 96-25075 98-25075 03-15316 55051-1817 11-14988 11-15180 93-25075 92-25075 Drawing Image Number DRVLN C6 47 75-20 CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 59
Driveline CV 540 RPM (826-643C) Weasler Section 5: Drivelines Applies to RC4610 37916 60 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Driveline CV 540 RPM (826-643C) Weasler Section 5: Drivelines Applies to RC4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. Dwg 37916 826-643C 26-15120 68810-1004 03-15570 26-16033 99-24406 19-15135 97-24406 96-24406 98-24406 03-15316 55051-1817 11-14988 11-15180 93-24406 92-24406 91-24406 Drawing Image Number DRVLN C6 42 38-6 CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT W/ CHAINS WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 61
Driveline Wing (826-811C) Comer Section 5: Drivelines 37917 62 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Driveline Wing (826-811C) Comer Section 5: Drivelines Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 Dwg 37917 826-811C 14026.357.1 180.016.780 146.26021 8180.016.237 8180.01240 8180.016.238 14260.5197621 165.000.589 180.01022 15016.037.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 812360.5011 812460.105611 190.000.098 190.000.099 190.000.903 Image No. DRVLN C4 50 75-20 FX CLTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET COMER CLUTCH, COMPLETE ASSY CO RETAINING COLLAR OUTER TUBE RPBY 180.01240 CO RETAINING COLLAR INNER TUBE CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARD COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER CO LABEL W/CUSTOMER CODE 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 63
Driveline Wing (826-812C) Comer Section 5: Drivelines 37918 64 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Driveline Wing (826-812C) Comer Section 5: Drivelines Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. 29. 30. 3 3 3 3 Dwg 37918 826-812C 14028.195.1 180.018.581 190.000.035 190.000.047 15018.241 190.000.243 150.285197810 159.280.168 190.000.271 15018.241 146.28020.1 180.018.251 180.01240 180.018.252 14286.2519821 165.000.589 180.01022 15018.016.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 14282509821 14287.2199821 12386.190.01 12486.3401 190.000.098 190.000.099 180.018.393 180.018.435 190.000.932 Image No. DRVLN C5 48 75-20 FX CLTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET N/A CO GREASE NIPPLE COMER YOKE OUTER COMER OUTER TUBE ROLL PIN CO COMPLETE OUTER TUBE W/LABEL COMER INNER TUBE COMER ROLL PIN FOR INNER TUBE COMER INNER YOKE COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO HALF FEMALE GUARD CO HALF MALE GUARD CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARDING COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER COMER CAP OUTER TUBE, PLASTIC COMER INNER CAP CO LABEL W/CUSTOMER CODE available only in cross journal set (#2) 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 65
Gearbox (826-721C) Applies to RC4610 Section 6: Gearboxes 33315 66 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Gearbox (826-721C) Section 6: Gearboxes Applies to RC4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. Dwg 33315 826-721C U0.125.05300 U0.125.60500 8.0.9.00143 8.7.00331 U0.125.2050.00 8.5.00332 A.709.500 8.5.00533 U0.125.7100.00 A.71500 8.0.9.01090 1871000 8.7.02349 8.0.9.00079 U0.125.30000 8.7.02265 0.1271000 0.288.71000 0.257525.00 0.285.7510.00 U0.125.13000 8.00501 8.6.5.00203 8.6.5.00006 8.00560 U0.125.50500 8.7.01045 826-486C Drawing Image Number GBOX RC50 75-20 1:60 CW * CO HOUSING CO GEAR CROWN Z24 M7.25 CO BRG 30209 TAPPERED CO OIL SEAL 45 X 85 X 10 SL CO INPUT SHAFT 1 3/4"-20 CO SNAP RING UNI 7437 COMER SHIM KIT CO SNAP RING 50 UNI7435 CO CASTLE NUT COMER SHIM KIT CO BRG 32210 TAPPERED CO SEAL PROTECTOR CO OIL SEAL 60X110X12 SL CO BRG 30212 TAPPERED CO OUTPUT SHAFT CO COTTER PIN B 5X60 CO CAP CO BLANK WASHER CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO TOP COVER CO BOLT M10X22 HHB CO PLUG 1/2" GAS CO OIL PLUG 3/8 CO CASTLE NUT M36X3 GEAR PINION Z15 M7.25 CO COTTER PIN B6X70 SLD-SPRTLY COMER U0.125.70000 DIPSTICK 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 67
Gearbox 1000 RPM (826-319C) Applies to RCM4610 Section 6: Gearboxes 21171 68 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Gearbox 1000 RPM (826-319C) Section 6: Gearboxes Applies to RCM4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. Dwg 21171 826-319C U0.125.05300 U0.125.50000 8.0.9.00143 8.7.00331 U0.125.2050.00 8.5.00332 0.709.7500.00 8.5.00533 U0.125.7100.00 0.717500.00 8.0.9.01090 1871000 8.7.02349 8.0.9.00079 U0.125.30000 8.7.02265 0.1271000 0.288.71000 0.257525.00 0.285.7510.00 U0.125.13000 8.00501 826-486C 8.6.5.00006 8.7.01045 8.00560 U0.125.60000 Drawing Image Number GBOX RCM50 75-20 1:21 CW * CO HOUSING CO CROWN GEAR Z22 M7.8 CO BEARING 30209 RTA25 CO OIL SEAL 45 X 85 X 10 CO INPUT SHAFT 1 3/4"-20 CO SNAP RING UNI 7437 CO SHIM 87 CO SNAP RING 50 UNI7435 CO CASTLE NUT CO SHIM 50.3X70.3 CO BEARING 32210 CO SEAL PROTECTOR CO OIL SEAL 60X110X12 CO BEARING 30212 CO OUTPUT SHAFT CO COTTER PIN B 5X60 CO CAP CO BLANK WASHER CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO COVER CO BOLT M10X22 HHB COMER U0.125.70000 OIL PLUG CO OIL PLUG 3/8 CO COTTER PIN B6X70 SLD-SPRTLY CO CASTLE NUT M36X3 CO CROWN GEAR Z18 M7.8 R. H. Deck 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 69
Gearbox 1000 RPM (826-725C) Applies to RCM4610 Section 6: Gearboxes 33338 70 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Gearbox 1000 RPM (826-725C) Section 6: Gearboxes Applies to RCM4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. Dwg 33338 826-725C U0.125.05300 U0.125.50600 8.0.9.00143 8.7.00331 U0.125.2050.00 8.5.00332 0.709.7500.00 8.5.00533 U0.125.7100.00 0.717500.00 8.0.9.01090 1871000 8.7.02349 8.0.9.00079 U0.125.30000 8.7.02265 0.1271000 0.288.71000 0.257525.00 0.285.7510.00 U0.125.13000 8.00501 826-486C 8.6.5.00006 8.7.01045 8.00560 U0.125.60600 Drawing Image Number GBOX RC50 15:1 STD * CO HOUSING CO GEAR PINION Z19 M7.8 CO BEARING 30209 RTA25 CO OIL SEAL 45 X 85 X 10 CO INPUT SHAFT 1 3/4"-20 CO SNAP RING UNI 7437 CO SHIM 87 CO SNAP RING 50 UNI7435 CO CASTLE NUT CO SHIM 50.3X70.3 CO BEARING 32210 CO SEAL PROTECTOR CO OIL SEAL 60X110X12 CO BEARING 30212 CO OUTPUT SHAFT CO COTTER PIN B 5X60 CO CAP CO BLANK WASHER CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO COVER CO BOLT M10X22 HHB COMER U0.125.70000 OIL PLUG CO OIL PLUG 3/8 CO COTTER PIN B6X70 SLD-SPRTLY CO CASTLE NUT M36X3 CO GEAR CROWN Z22 M7.8 * Notes: Oil Type 80-90W Capacity 10 Pints Center Deck 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 71
Gearbox 540 RPM (826-650C) Applies to RC4610 Section 6: Gearboxes 30528 72 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Gearbox 540 RPM (826-650C) Section 6: Gearboxes Applies to RC4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. Dwg 30528 826-650C U0.125.05300 U0.125.60500 8.0.9.00143 8.7.00331 U0.125.2050.00 8.5.00332 A.709.500 8.5.00533 U0.125.7100.00 A.71500 8.0.9.01090 1871000 8.7.02349 8.0.9.00079 U0.125.30000 8.7.02265 0.1271000 0.288.71000 0.257525.00 0.285.7510.00 U0.125.13000 8.00501 8.6.5.00203 8.6.5.00006 8.00560 U0.125.50500 8.7.01045 826-486C Drawing Image Number GBOX RCF36 75-20 1:60 CCW * CO HOUSING CO GEAR CROWN Z24 M7.25 CO BRG 30209 TAPPERED CO OIL SEAL 45 X 85 X 10 SL CO INPUT SHAFT 1 3/4"-20 CO SNAP RING UNI 7437 COMER SHIM KIT CO SNAP RING 50 UNI7435 CO CASTLE NUT COMER SHIM KIT CO BRG 32210 TAPPERED CO SEAL PROTECTOR CO OIL SEAL 60X110X12 SL CO BRG 30212 TAPPERED CO OUTPUT SHAFT CO COTTER PIN B 5X60 CO CAP CO BLANK WASHER CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO TOP COVER CO BOLT M10X22 HHB CO PLUG 1/2" GAS CO OIL PLUG 3/8 CO CASTLE NUT M36X3 GEAR PINION Z15 M7.25 CO COTTER PIN B6X70 SLD-SPRTLY COMER U0.125.70000 DIPSTICK 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 73
Gearbox Divider 1000 RPM (826-521C) Comer Section 6: Gearboxes Applies to RCM4610 26960 74 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Gearbox Divider 1000 RPM (826-521C) Comer Section 6: Gearboxes Applies to RCM4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 1 Dwg 26960 826-521C 8.00109 0.305.1300.00 8.0.9.00143 8.5.01772 8.7.00331 0.305.0300.01 0.709.7500.00 N/A 0.305.3000.00 0.305.2000.00 N/A 8.6.6.00201 826-848C 826-497C A.305.501 Drawing Image Number DIV BOX COMER 1000RPM 1 3/4-20 * CO BOLT M10 X 35 8.8 TOP COVER PLATE CO BEARING 30209 RTA25 CO SNAP RING CO OIL SEAL 45 X 85 X 10 CO CASING CO SHIM 87 RPBY A.305.501 CO SHAFT 1" 3/4 Z20 CO SHAFT 1" 3/4 Z20 RPBY A.305.501 CO PLUG 3/8 GAS COMER 0.340.71000 DIPSTICK COMER VENT #8.6.7.00269 CO TRIAD GEAR Z20-Z24-Z24 M6.5 * Notes: Oil Type 80-90W Capacity 5.5 Pints S/N 1011370+ S/N 1011369- Contains 2 of gear #8 and 1 of gear #11 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 75
Gearbox Divider 1000 RPM (826-521C) ITG Section 6: Gearboxes Applies to RCM4610 25682 76 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Gearbox Divider 1000 RPM (826-521C) ITG Section 6: Gearboxes Applies to RCM4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 2 Dwg 25682 826-521C 18-059 804-158C 06-003 20-019 02-038 05-007 04-011 08-006 08-007 08-008 20-018 05-012B 02-039 10-001 17-002 17-001 17-003 03-126 03-127 11-012 12-008 07-022 09-013 16-110 09-011 Drawing Image Number DIV BOX 1000RPM 1 3/4-20 * ITG HOUSING WASHER SPRING LOCK M10 PLT ITG M10 X 5 X 30 CAP SCREW ITG INPUT CAP SPLITTER BOX ITG INPUT SHAFT ITG INPUT SHAFT OIL SEAL ITG BRG ASSEMBLY ITG INPUT CAP GASKET 0.10MM ITG INPUT CAP GASKET 0.25MM ITG IN & OUT CAP GASKET 0.45MM ITG HORIZONTAL HUB CAP ITG OUTPUT SEAL 58X95X10 THK ITG OUTPUT SHAFT ITG SPACER ITG SHIM 0.3 ITG SHIM 0.4 ITG SHIM 0.5 19 TOOTH GEAR ITG 23 TOOTH GEAR ITG BRG ADJ. NUT ITG COTTER PIN ITG SEALING WASHER ITG DRAIN PLUG ITG M18X5 DIP STICK BREATHER ITG M18 X 5P PLUG VENTED * Notes: Oil Type 80-90W Capacity 5.5 Pints S/N + S/N - 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 77
Gearbox Divider 540 RPM (826-520C) Comer Section 6: Gearboxes Applies to RC4610 26959 78 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Gearbox Divider 540 RPM (826-520C) Comer Section 6: Gearboxes Applies to RC4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 1 dwg26959 826-520C 8.00109 0.305.1300.00 8.0.9.00143 8.5.01772 8.7.00331 0.305.0300.01 A.709.500 N/A 0.305.3000.00 0.305.2000.00 N/A 8.6.6.00201 826-848C 826-497C A.305.500 Drawing Image Number DIV BOX COMER 540RPM 1 3/4-20 * CO BOLT M10 X 35 8.8 TOP COVER PLATE CO BEARING 30209 RTA25 CO SNAP RING CO OIL SEAL 45 X 85 X 10 CO CASING COMER SHIM KIT RPBY A.305.500 CO SHAFT 1" 3/4 Z20 CO SHAFT 1" 3/4 Z20 RPBY A.305.500 CO PLUG 3/8 GAS COMER 0.340.71000 DIPSTICK COMER VENT #8.6.7.00269 CO TRIAD GEAR Z20-Z20-Z24 M6.5 * Notes: Oil Type 80-90W Capacity 5.5 Pints S/N 1011370+ S/N 1011369- Contains 2 of gear #8 and 1 of gear #11 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 79
Gearbox Divider 540 RPM (826-520C) ITG Section 6: Gearboxes Applies to RC4610 25681 80 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Gearbox Divider 540 RPM (826-520C) ITG Section 6: Gearboxes Applies to RC4610 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 2 Dwg 25681 826-520C 18-059 804-158C 06-003 20-019 02-038 05-007 04-011 08-006 08-007 08-008 20-018 05-012B 02-039 10-001 17-002 17-001 17-003 03-127 03-126 11-012 12-008 07-022 09-013 16-110 09-011 Drawing Image Number DIV BOX 540RPM 1 3/4-20 * ITG HOUSING WASHER SPRING LOCK M10 PLT ITG M10 X 5 X 30 CAP SCREW ITG INPUT CAP SPLITTER BOX ITG INPUT SHAFT ITG INPUT SHAFT OIL SEAL ITG BRG ASSEMBLY ITG INPUT CAP GASKET 0.10MM ITG INPUT CAP GASKET 0.25MM ITG IN & OUT CAP GASKET 0.45MM ITG HORIZONTAL HUB CAP ITG OUTPUT SEAL 58X95X10 THK ITG OUTPUT SHAFT ITG SPACER ITG SHIM 0.3 ITG SHIM 0.4 ITG SHIM 0.5 ITG 23 TOOTH GEAR 19 TOOTH GEAR ITG BRG ADJ. NUT ITG COTTER PIN ITG SEALING WASHER ITG DRAIN PLUG ITG M18X5 DIP STICK BREATHER ITG M18 X 5P PLUG VENTED * Notes: Oil Type 80-90W Capacity 5.5 Pints S/N + S/N - 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 81
Hydraulic Components Section 7: Hydraulics 70313 82 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hydraulic Components Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. Dwg 70313 318-018H 318-648D 800-060C 800-306C 802-017C 803-209C 804-011C 804-029C 805-088C 805-104C 807-023C 810-312C 810-624C 810-818C 811-062C 811-063C 811-394C 811-619C 841-552C 235005 Image No. WLDMT. CYLINDER PIN TRANSPORT BAR CABLE TIE.19X125 3DIA 50LB FILL PLUG VENTED 3/4-16 PLT HHCS 3/8-16X1 GR5 NUT FLANGE LOCK 3/8-16 PLT WASHER FLAT 3/8 USS PLT WASHER FLAT 1 SAE PIN, HAIR COTTER 3/16 WIRE DIA PIN COTTER 3/16 X 1 1/2 PLT SPRING HOSE LOOP CYL 3X12X25 ROD (TIE ROD) CYL 3X8X25 ROD (TIE) NO PINS STRK CNTRL SPCRS 125 TO 50 OREL 1/32 9/16MJIC 9/16MORB EL 3/4MJIC 3/4MORB CP 3/4FORB MALE QD POPPET TYPE HH3/8R1 168 3/4MORB 3/4FJIC HH3/8R2 217 3/4MORB 9/16FJIC MON PIN KIT 00C/W COTTER PIN Includes 2 clevis pins & 4 cotter pins 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 83
Hydraulic Cylinder (810-312C) Cross Section 7: Hydraulics 15572 84 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hydraulic Cylinder (810-312C) Cross Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 19. Dwg 15572 810-312C 1D1505-3 2A0235-6 2A0578-1675 1D0005-1450 2A0079-616 1D1551-16275 2A0308-1 1D1003-5 2A0235-6 1D0206-1675 1D1155-17 1D1401-250 2A0246-12 810-177C 810-178C Drawing Image Number CYL 3X12X25 ROD (TIE ROD * BASE CROSS CROSS NUT,CLEVIS AND TIE ROD O-RING TIE ROD CROSS TUBE CROSS CROSS SCREW CAP CROSS CLEVIS PIN CROSS PIN,CLIP CROSS ROD CLEVIS CROSS NUT, CLEVIS AND TIE ROD ROD CROSS WIPER BACK-UP O-RING HEAD CROSS BACK UP PISTON CROSS CROSS NUT,PISTON SEAL KIT MW 5X25ROD 3A3104 SEAL KIT CROSS 5 CYL 1C498 Only found in seal kit 20. Only found in seal kit 20. Only found in seal kit 20. Only found in seal kit 20. Only found in seal kit 20. 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 85
Hydraulic Cylinder (810-312C) Lion Section 7: Hydraulics 25902 86 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hydraulic Cylinder (810-312C) Lion Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. Dwg 25902 810-312C 803-020C 130560 801-023C 186561 N/A N/A N/A N/A N/A N/A 258821 491742 492282 492652 492721 494383 492870 810-887C Drawing Image Number CYL 3X12X25 ROD (TIE ROD) * NUT HEX 1/2-13 PLT MON PISTON NUT SCREW SET SH 3/8-16X3/8 TYPE C PLUG 9/16-18UNF MORB SOCKET HD MON ROD SEAL MON PISTON SEAL (PSP) MON END CAP B/U WASHER MON END CAP O-RING SEAL WIPER ROD MON PISTON WEAR RING MON PISTON 00-0-TSS-ISO-WR MON CYL TUBE MON TIE ROD LION ROD CLEVIS 1 1/4 (1PIN) LION CLEVIS CAP 0-9/16 ORB MON ROD CAP00-25-9/16ORBTS MON CYL ROD MON SEAL KIT 661702 Only Found in Kit #18 Only Found in Kit #18 Only Found in Kit #18 Only Found in Kit #18 Only Found in Kit #18 Only Found in Kit #18 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 87
Hydraulic Cylinder (810-312C) Midway Section 7: Hydraulics 15242 88 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hydraulic Cylinder (810-312C) Midway Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. Dwg 15242 810-312C 1M6010 2M4418 3M4410 4M4104 5M4120 6M4152 7M4320 2A0208 N/A N/A N/A N/A N/A 2A0024 2A0014 2A0012 2A0006 2A0132 810-015C N/A Drawing Image Number CYL 3X12X25 ROD (TIE ROD * MW CLEVIS STD. DUTY MW ROD 1-1/4 DIA. X 10 STROKE MW HEAD CAP 3X1-1/4 RD 9/16SAE MW PISTON 3 DIA. MW TUBE 3 X 15 CYLINDER MW BASE 3 X 9/16 SAE MW TIE ROD 3 X 10 CYLINDER MW CLEVIS PIN MW WIPER MW O-RING MW BACK-UP MW O-RING MW BACK UP MW PISTON NUT 1-14 MW TIE ROD NUT MW NUT CLEVIS & TIE ROD MW CAPSCREW MW PIN CLIP CYL SEAL KIT 3 X 7 MW 3A4104 Crown Seal Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 As Required 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 89
Hydraulic Cylinder (810-624C) Midway Section 7: Hydraulics 12499 90 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hydraulic Cylinder (810-624C) Midway Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. Dwg 12499 810-624C 6R1164-ADI 6M4166 2A0014 7M4316 5M4116 2A0006 1M6010-ADI 2A0012 2M4416 3M4412 4M4104 2A0024 810-015C Drawing Image Number CYL 3X8X25 ROD (TIE) NO PINS * MIDWAY ADI BASE RPBY 6R1164-ADI MW TIE ROD NUT O-RING MW TIE ROD 3 X 8 CYLINDER MW TUBE 3 X 8 CYLINDER MW CAPSCREW MIDWAY HARDENED CLEVIS ADI MW NUT CLEVIS & TIE ROD MW ROD 1-1/4 DIA X 8 STROKE WIPER BACK-UP O-RING MW HEAD CAP 3X1-1/4 ROD 3/4SAE BACK-UP MW PISTON 3 DIA. MW PISTON NUT 1-14 CYL SEAL KIT 3 X 7 MW 3A4104 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 91
Hydraulic Cylinder (810-624C) Red Lion Section 7: Hydraulics 25896 92 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Hydraulic Cylinder (810-624C) Red Lion Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. Dwg 25896 810-624C 803-020C 130560 801-023C 186562 N/A N/A N/A N/A N/A N/A 292003 258818 491738 492278 494391 492675 493211 493830 810-887C Drawing Image Number CYL 3X8X25 ROD (TIE) NO PINS * NUT HEX 1/2-13 PLT MON PISTON NUT SCREW SET SH 3/8-16X3/8 TYPE C LION PLUG 3/4-16UNF SOCKET HD MON ROD SEAL MON PISTON SEAL (PSP) MON END CAP B/U WASHER MON END CAP O-RING SEAL WIPER ROD MON PISTON WEAR RING MON TIE ROD EXTND THD MON PISTON50-.750-TSS-ISO-WR MON CYL TUBE MON TIE ROD MON ROD CP50-12-9/16ORB-TS MON CLEVIS CAP MON CYL ROD LION HARDENED ROD CLEVIS 1 1/4 MON SEAL KIT 661702 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 93
Manual Winch Wing Deck Section 8: Options & Accessories 27689 94 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Manual Winch Wing Deck Section 8: Options & Accessories Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 Dwg 27689 330-295A 330-294H 802-023C 802-055C 803-013C 803-263C 804-011C 804-013C 804-019C 890-671C 890-679C 890-680C Drawing Image Number MECHANICAL WINCH RC55 * MECHANICAL WINCH HHCS 3/8-16X1 3/4 GR5 HHCS 5/8-11X2 GR5 NUT LOCK 3/8-16 PLT NUT HEX FLANGE LOCK 5/8-11 PLT WASHER FLAT 3/8 USS PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 5/8 USS PLT BRAKE WINCH DLB2000 WINCH HANDLE 12" DBL2000 WINCH CABLE AND HOOK 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 95
Off Center Lights 3 Inch (LED) Retro-Fit (334-579A) Section 8: Options & Accessories 39037 96 RC4610 & RCM4610 Rotary Cutter 334-144P 07/11/18
Off Center Lights 3 Inch (LED) Retro-Fit (334-579A) Section 8: Options & Accessories Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 1 1 1 1 1 1 15. 16. 17. 18. Dwg 39037 334-496L 334-574M 330-965D 330-966D 330-967D 800-060C 802-015C 802-027C 802-224C 803-078C 803-209C 803-255C 804-007C 891-522C J-37-R J-37-A J-AC1-15-B 891-523C J-37-R J-37-A J-AC1-15-B 891-529C 891-530C 891-531C 891-532C 891-534C Image No. OFFSET CUTTER LIGHT KIT 3" ROTARY CUTTER LIGHT KIT MANUAL * LIGHT MNT LIGHT GUARD LIGHT MNT CLAMP CABLE TIE.19X125 3DIA 50LB RHSNB 3/8-16X1 GR5 HHCS 3/8-16X4 1/2 GR5 HHCS 1/4-20X1 1/4 GR5 NUT LOCK 3/8-16 NYLON INSERT NUT FLANGE LOCK 3/8-16 PLT NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT DUAL LED LIGHT LH RED LED LENS MODULE AMBER LED LENS MODULE BLACK LENS COVER DUAL LED LIGHT RH RED LED LENS MODULE AMBER LED LENS MODULE BLACK LENS COVER LIGHT WIRE HARNESS 8' RPBY 891-529C ENHANCE MODULE LEAD WIRE HARNESS 8' LIGHT MAGNETS WITH HARDWARE Complete light assembly Red lens Amber lens Black lens Complete light assembly Red lens Amber lens Black lens Obsolete 07/11/18 RC4610 & RCM4610 Rotary Cutter 334-144P 97