Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 General information Features Design basis The 16mm dia. series of compact size pushbuttons are 'finger-size', and consequently take up little panel space. 165-2 series operators are about twice as large as the 164 and 165 series operators for easier operation. With many types of operator available, the most suitable switch can be identified by color, shape and legend, and have a smooth, quality "snap-action". In spite of their small size they have a highly reliable mechanism, and are eminently suited for solid state and other electronic circuits. 164, 165 and 165-2 series contact block holders can easily be removed manually. Moreover, the contact block can be easily attached or detached without using any special tools, thus facilitating addition or replacement of contact. elector switches elector switches can also be supplied in either knob-handle operated or key operated types. trong construction The operator and contact blocks are molded from an excellent thermal resistance resin and can withstand the heat at the time of soldering. ince these pushbuttons are manufactured to industrial standards they can withstand vibration or shock thus eliminating lamp failure due to such causes as loose bases. With regard to the degree of protection, standard types which met the requirements of IP40 of Pub. No. 529, IC tandards, and oil tight types which meet the requirements of IP65 of the said, are available. This permits the application to various fields, from machine tools to O (Office utomation) facilities. Quality feel tough Both the operator and contact block are precisely engineered. There is no fear of the switch malfunction even after long use and it continues to operate smoothly for its service life of about 1,000,000 operations. Pushbuttons Illuminated pushbuttons Pilot lights K-1103 164-164-T 164-Z mergency stop pushbuttons asy color change Color lenses fit over the inner button. The lens can easily be removed using a small screwdriver Color lens F97-231 165-V6 crew driver Note: The luminous color of Ds and neon illumination types varies with the body color of the product. Visible inscription Button legends are printed on legend sheet, which is stuck to the legend plate on the inner button. The lettering is back lit by the switch lamp and the inscription is highly visible through the color lens. Contact FUJI for your lettering requirements. egend plate egend sheet (film) xcellent switch reliability The switch uses a snap-action mechanism. The pushbuttons are available with either momentary or alternative actions. The snap-action switch has a double break movement which operates independently of the speed of switching. The contacts are made from gold-flashed silver. igh contact reliability of 1m at 5V C/DC is assured. Contact blocks are available in to arrangement. arge terminals older/tab terminal is provided as standard. Wire-wrap terminal is available on reguest. K-1100 F87-221 165-2M electors K-1139 F87-208 165-2P afety FUJI s original Trigger ction mechanism is used in the emergency stop pushbuttons. They are suitable for emergency stop and safety. This mechanism prevents the contacts from moving until the button is pushed and locked. Provided with a trigger action mechanism conforming to N4. Provided with direct opening action (approved by TÜV) conforming to N60947-5-1 and N60947-5-5. lternate action In the case of alternate action when the button is depressed the contacts are maintained and remain so even if the finger is removed. The button will not return to its free position. In order to remove the lock, the button must be given a second pressure before the button will return to its free position. This makes it most suitable as the switch for a power source. Maintain Pushbutton with finger guards Finger guards are provided for square or rectangular type pushbuttons (F, TF, and T types) in order to prevent operational error of adjacent buttons. pprovals amp terminal Contact terminal For further information related to approved type, see page /132 to /136. Fuji lectric F Components & ystems Co., td./d & C Catalog /131
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 Quick reference guide 164 (standard) / 165 (oil-tight) Illuminated pushbutton switches Operator Type Operator Type Operator Type xtended round head 164-, 5 Flush square head 164-, 5 Flush rectangular head 164-T, T5 165-, 5 165-, 5 165-T, T5 ee page /142 ee page /142 ee page /142 K-1103 K-1102 K-1100 Flush rectangular head 164-TG, TG5 Flush square head 164-G, G5 with guard 165-TG, TG5 with guard 165-G, G5 ee page /143 ee page /143 K-1101 Note: pot D and red/green D types: Not approved standard Pushbutton switches Operator Type Operator Type Operator Type xtended round head 164-, 5 Mushroom head 164-M, M5 Flush square head 164-F, F5 165-, 5 165-M, M5 165-F, F5 F90-301 ee page /147 ee page /147 ee page /147 K-1103 K-1136 K-1102 Flush rectangular head 164-TF, TF5 Flush rectangular head 164-TGF, TGF5 Flush square head 164-GF, GF5 165-TF, TF5 with guard 165-TGF, TGF5 with guard 165-GF, GF5 ee page /147 ee page /147 ee page /147 K-1100 K-1101 F90-301 Convex square head 164-M, M5 Convex rectangular head 164-TM, TM5 Push-lock, turn-reset 165-V 165-M, M5 165-TM, TM5 (32mm dia.) (Direct opening action) ee page /147 ee page /147 ee page /148 Push-lock, turn-reset (40mm dia.) 165-V1 K-1134 K-1135 F91-584 (Direct opening action) ee page /148 F91-583 mergency stop pushbutton switches (Direct opening action), conform to N4 Operator Type Operator Type Push-lock, turn-reset 165-V5 Push-lock, turn-reset 165-V6 (32mm dia.) (40mm dia.) ee page /148 ee page /148 F97-232 F97-231 Note: : ee page /5 /132 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 Quick reference guide elector switches Operator Type Operator Type Operator Type Knob with rectangular 164-P Knob with square bezel 164-P Key with rectangular 164-J bezel 165-P 165-P bezel 165-J ee page /149 ee page /149 ee page /149 K-1099 K-1133 K-1098 Key with square bezel 164-J Key with rectangular 165-JM Key 165-JM 165-J bezel (Direct opening action) (Direct opening action) ee page /149, /2 ee page /0 ee page /0 K-1132 F95-57 F99-320 Pilot lights ens Type ens Type ens Type xtended round 164-Z Flush square 164-Z Flush rectangular 164-ZT 165-Z 165-Z 165-ZT ee page /4 ee page /4 ee page /4 Dome 165-ZM K-1139 K-1138 K-1137 ee page /4 F87-45 Buzzers ound Type ound Type ound Type tandard 164-TX oud sound 164-TX1 oud sound with 164-TX2B volume control ee page /6 ee page /6 ee page /6 tandard sound with volume control (IP54) 165-X F87-317 F87-44 F93-297 ee page /6 F96-3 Note: : ee page /5 Fuji lectric F Components & ystems Co., td./d & C Catalog /133
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 Quick reference guide Numerical indicators Display Type Display Type Display Type Without decimal decoder 164-T With decimal decoder 164-TC With decimal decoder 164-TC4 165-T (5, 12, V) 165-TC (V) 165-TC4 ee page /7 ee page /7 ee page /7 With sign decorder 164-TC4-1 (±1 display) 165-TC4-1 P-165 F87-3 F89-948 ee page /7 F88-1093 165-2 (oil-tight) Illuminated pushbutton switches Operator Type Operator Type Operator Type Flush round head 165-2F, 2F5 xtended round head 165-2, 25 Mushroom head 165-2M ee page /164 ee page /164 ee page /164 F87-211 F87-210 F87-221 Mushroom head with 165-2YM Flush square head 165-2F, 2F5 xtended square head 165-2, 25 square bezel ee page /164 ee page /165 ee page /165 F87-220 F87-201 F87-200 Concave square head 165-2C, 2C5 Push-lock, turn-reset 165-2V Push-lock, turn-reset 165-2YV with square bezel ee page /165 ee page /166 ee page /166 F87-199 F87-219 F87-2 Note: : ee page /5 /134 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 Quick reference guide Pushbutton switches Operator Type Operator Type Operator Type Flush round head 165-2F, 2F5 xtended round head 165-2, 25 Mushroom head 165-2M ee page /167 ee page /167 ee page /167 F87-211 F87-210 F87-2 Mushroom head with 165-2YM Flush square head 165-2F, 2F5 Concave square head 165-2C, 2C5 square bezel ee page /167 ee page /167 ee page /167 F87-214 F87-201 F87-199 xtended square head 165-2, 25 With selector ring 165-22 With selector ring 165-2Y2 with square bezell ee page /167 ee page /168 ee page /168 F87-200 F87-207 F87-206 Push-lock, turn-reset 165-2V Push-lock, turn-reset 165-2YV with square bezel ee page /168 ee page /168 F87-217 F87-216 elector switches Operator Type Operator Type Operator Type Knob 165-2P Knob with square bezel 165-2YP Key 165-2J ee page /169 ee page /169 ee page /169 F87-208 F87-202 F87-223 Key with square bezel 165-2YJ ever 165-2 ever with square bezel 165-2 ee page /169 ee page /170 ee page /170 F87-222 F87-209 F87-203 Illuminated selector switches Operator Type Knob 165-2P ee page /172 F87-607 Note: : ee page /5 Fuji lectric F Components & ystems Co., td./d & C Catalog /135
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 Quick reference guide Pilot lights ens Type ens Type ens Type Flush round 165-2Z xtended round 165-2Z Flush square 165-2Z ee page /173 ee page /173 ee page /173 F87-213 F87-212 F87-205 xtended square 165-2Z ee page /173 F87-2 Note: : ee page /5 /136 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164 and 165 Type number nomenclature Type number nomenclature Pushbuttons, illuminated pushbuttons and pilot lights ➂ Color of button or lens 165-11 3 W ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 164: tandard (IP40) 165: Oil-tight (IP65) ➁ Operator or lens Operator for illuminated pushbutton : Flush square head 5: Flush square head (lternate) T: Flush rectangular head T5: Flush rectangular head (lternate) : xtended round head 5: xtended round head (lternate) TG: Flush rectangular head with guard TG5: Flush rectangular head with guard (lternate) G: Flush square head with guard G5: Flush square head with guard (lternate) Code G B Y W O G color Green ed Black* Yellow White Blue Orange ed/green Button Notes: ( ): indicates luminous color 165-V, V1, V5, V6: ed only * Not available for illuminated types D Incandescent (Orange) (mber) ➃ Contact arrangement 01: 1NC* 2: 02: 2NC* 1 33: * 2 11: Notes: * 1 vailable for 165-V, V1, V5, V6 * 2 Not available for with transformer types Neon (Orange) (Orange) (Orange) (Green) Operator for pushbuttons F: Flush square head F5: Flush square head (lternate) TF: Flush rectangular head TF5: Flush rectangular head (lternate) : xtended round head 5: xtended round head (lternate) TGF: Flush rectangular head with guard TGF5: Flush rectangular head with guard (lternate) GF: Flush square head with guard GF5: Flush square head with guard (lternate) M: Mushroom head M5: Mushroom head (lternate) M: Convex square head M5: Convex square head (lternate) TM: Convex rectangular head TM5: Convex rectangular head (lternate) V: Push-lock, turn-reset (32mm dia.)* 1 * 2 V1: Push-lock, turn-reset (40mm dia.)* 1 * 2 Operator for emergency stop pushbuttons V5: Push-lock, turn-reset (32mm dia.)* 2 V6: Push-lock, turn-reset (40mm dia.)* 2 ens for pilot lights Z: xtended round Z: Flush square ZT: Flush rectangular ZM: Dome ➄ amp voltage Code B K M P D Incandescent* 2 Neon* 2 5V DC* 2 6V DC* 2 12V DC V DC 100-110V C* 1 * 2 200-220V C* 1 * 2 ➅ Type of lamp Blank: Incandescent 1: Neon 2: pot D, D (ZM types) 3: Flat D 5V C/DC 12V C/DC V C/DC 100-110V C* 1 200-220V C* 1 Notes: * 1 With transformer (D: V, Incandescent: 28V) * 2 Not available 165-ZM ZM type: D lamp only (12, V DC) ➆ Terminal Blank: older/tab W: Wire-wrap : oder (165-V, V1, V5, V6 types only) Note: ZM types: wire-wrap terminal only (Code is blank) 110V C 120V C 220V C 0V C Note: * 1 Product with no trigger action mechanism * 2 165 type only, direct opening action Fuji lectric F Components & ystems Co., td./d & C Catalog /137
Pushbuttons/electors/Pilot ights/buzzers 164 and 165 Type number nomenclature Type number nomenclature elector switches 165 - J 2 B 11 W ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 164: tandard (IP40) 165: Oil-tight (IP65) ➁ Operator 2-position, 3-position (operating angle 90 ) P: Knob with square bezel P: Knob with rectangular bezel J: Key with square bezel J: Key with rectangular bezel JM: Key with rectangular bezel (Direct opening action) * JM: Key (Direct opening action) * Note: * 165 types (2-position) only 3-position (operating angle 45 ) PK: Knob with square bezel PK: Knob with rectangular bezel JK: Key with square bezel JK: Key with rectangular bezel ➂ Operation 2: 2-position, maintained 0: 2-position, spring return* 3: 3-position, maintained 6: 3-position, spring/manual return (eft to center) 7: 3-position, spring/manual return (ight to center) 1: 3-position, spring return Note: * xcept for JM and JM types ➆ Terminal Blank: older/tab W: Wire-warp Note: JM, JM types: older/tab terminal only Buzzers 164 - T X B ➀ ➁ ➂ ➃ ➀ Product category 164: tandard (IP00) 165: plash-proof (IP54) ➁ ound TX: tandard (164) TX1: oud sound (164) TX2: oud sound with volume control (164) X: tandard sound with volume control (165) ➂ Color of head B: Black ➃ Operating voltage C: 6V C* 2 DC: 6V DC* 2 : 6V C/DC* 1 : 12 to V C/DC F: 35 to 48V C/DC Notes: * 1 xcept for TX and TX1 types * 2 xcept for TX2 and X types ➃ Color of knob or key removable position Color of knob B: Black Key removable position Code B C D F G 2-position 2 0 3-position (operating angle 90 ) 3-position (operating angle 45 ) 1 3 6 7 1 3 6 7 ➄ Contact arrangement 11: 22: 33: * Note: * xcept for JM and JM types. ➅ Key type No. (standard), B, C, D,, F /138 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164 and 165 Type number nomenclature Type number nomenclature Numerical indicators 164 - T C4 1 N K ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➇ ➀ Product category 164: tandard (IP40) 165: plash-proof (IP54) ➁ hape of the indicator T: ectangular ➂ Type of decoder : Without decoder C1: With decoder (7447: TT, positive logic) C4: With decoder (4511: C-MO) ➃ uminous color : ed G: Green ➄ Type of common or operating voltage Type of common (without decoder) : node C: Cathode Operating voltage (with decoder) Blank: 5V DC B: 12V DC * C: V DC * : V DC * Note: * TC4 types only ➅ Type of indicator Blank: Decimal* 1 1: ign (±1 display)* 2 Notes: * 1 Input voltage: 5, 12, V DC * 2 Input voltage: V DC ➆ Input logic Blank: Positive logic N: Negative logic * Note: * Input voltage: V DC ➇ Card connector (Input voltage: V DC) K1: Without connector K: With connector Fuji lectric F Components & ystems Co., td./d & C Catalog /139
Pushbuttons/electors/Pilot ights/buzzers 164 and 165 atings and specifications tandards approved U508 C C22.2 No.14 TÜV: N60947-5-1 TÜV: N60947-5-1 N60947-5-5 pecifications (Indoor use) Pushbutton switches, illuminated pushbutton switches selector switches, pilot lights Item 164 165 ated insulation voltage 250V C/DC mbient temperature 20 to +70 C * 1 10 to +70 C * 2 (no condensation or no icing) umidity 45 to 85% (at 5 to +40 C), no condensation or no icing Durability Mechanical Pushbutton switch (operations) Momentary action: 1 million lternate action: 250,000 Push-lock, turn-reset: 100,000 elector switch: 250,000 * 3 lectrical 100,000 (220V C 0.7) Dielectric strength 2000V C, 1 minute (Between lamp and contact terminals: 00V C, 1 minute) Conditional short-circuit current 1000 hort-circuit protective device Fuse 1 * 4 File No. 44592 File No. 279 (except for 165-ZM) File No. 84365 (for 165-ZM) Pushbutton (except for 165-V, V1), Illuminated pushbutton: 9250087 Pushbutton (for 165-V, V1): J9551059 elector (except for 165-JM, JM): 9250088 elector (for 165-JM, JM): J9551059 Pilot lights: 9250089 Buzzer: J9950092 (for 164-TX2, 165-X) mergency stop pushbutton: 9950093 Pollution degree 3 Vibration esonance: 10 to 55z, double amplitude 0.1mm * 5 Constant: 16.7z, double amplitude 3mm hock Malfunction durability: 100m/s 2 * 6 Mechanical durability: 500m/s 2 Operating frequency 1200 operation/hour (on-load factor: 40%) Insulation resistance 100MΩ or more (500V DC megger) Degree of protection IP40 IP65 Notes: * 1 For illuminated pushbutton switch and pilot light: 20 to +55 C * 2 For illuminated pushbutton switch and pilot light: 10 to +55 C * 3 Key insertion/removal durability for selector switch key types: 10,000 * 4 165-V, V1, JM, JM, V5, V6 types: Fuse 5 * 5 mergency stop type: 10 to 500z, double amplitude 0.7mm (acceleration 50m/s 2 ), according to the test condition of N60947-5-5 (1998) * 6 mergency stop type:0m/s 2 Buzzers Item 164-TX 164-TX1 ated insulation voltage Operating voltage 60V C/DC 6V C, 6V DC,12 to V C/DC 35 to 48V C/DC ound level 80dB (0.1m) 90dB (0.1m) 60dB(1m) 70dB(1m) Durability 1000h Frequency 2 ±0.5kz 2.4 to 3.3kz Intermittent cycle pprox. 170 cycle/minute Current consumption 7m(, 48V DC) m (, 48V DC) m(6v DC) 25m (6V DC) Dielectric strength Insulation resistance mbient temperature umidity Operator protection 20m (6, V C) 30m (48V C) 1000V C, 1 minute 30m (V C) 40m (48V C) 50m (6V C) 100MΩ or more (500V DC megger) 20 to +60 C (no condensation or no icing) 45 to 85% (at 5 to +40 C) IP00 Item 164-TX2 165-X ated insulation voltage Operating voltage 60V C/DC 6V C/DC, 12 to V C/DC 35 to 48V C/DC ound level 70dB to 90dB (0.1m) 60dB to 80dB (0.1m) 50dB to 70dB (1m) 40dB to 60dB (1m) Durability 1000h Frequency 2 ±0.5kz 2.4 to 3.3kz Intermittent cycle pprox. 170 cycle/minute Current consumption 30m (6V DC) 20m (, 48V DC) 40m (6,, 48V C) Dielectric strength 1000V C, 1 minute Insulation resistance 100MΩ or more (500V DC megger) mbient temperature umidity 20 to +60 C (no condensation or no icing) 45 to 85% (at 5 to +40 C) Degree of protection IP00 IP54 /140 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164 and 165 atings and specifications Numerical indicators Without decoder Item 164-T (D) 165-T (D) lectrical Forward voltage VF (IF=10m) ed: 2.0V (max. 2.8V), green: 2.1V (max. 2.8V) everse current I (V=3V) 100µ Max. power dissipation pd/eg Max. forward current IF Max. reverse voltage V ed: 40mW, green: 60mW ed: m, green: 20m 3V Opening Topr -20 to +40 C (No condensation or no icing) mbient temperature torage Tstg Degree of protection -30 to +85 C IP40 IP65 With decoder Item 164-TC1, TC4 165-TC1, TC4 164-TC4 165-TC Power supply VCC, VDD (DC) Current consumption mbient Opening Topr temperature torage Tstg Degree of protection 5V±5%, 12V±5%, V±5%, 5V ed: 120m (C1), 100m (C4), green: 170m (C1), 0m (C4) 12V ed: 90m (C4), green: 130m (C4) V±20% Numerical indicator, decimal: 110m Unit indicator: 80m V ed: 90m (C4), green: 130m (C4) -20 to +40 C (No condensation or no icing) -30 to +85 C -20 to +40 C (No condensation or no icing) -30 to +85 C IP40 IP65 IP40 IP65 Contact ratings U/C standards ated thermal current 5 ated operational voltage V 125V 250V Maximum current C (es. load) 5.0 DC (es. load) 1.0 0.2 N standards (TÜV approved) ated thermal current 5 ated operational voltage V 100 to 120V 100 to 125V 200 to 0V ated operational current C (Ind. load) 0.3 0.3 C 13 (Ind. load) 1.0 0.7 C 12 (es. load) 1.5 1.0 DC 13 (Ind. load) 0.7 0. DC 12 (es. load) 1.0 0.2 amp ratings ated operational voltage 5V 6V 12V V 110V 120V 220V 0V Consumption D DC 14m (Yellow: 28m) 14m (Yellow: 28m) 14m 14m Incandescent C/DC 0.45W (6V) 0.55W (14V) 0.55W (28V) Neon C 0.19V 0.21V 0.38V 0.42V Notes: With transformer (D): 1.5V/110, 220V With transformer (Incandescent): 2V/110, 220V For the incandescent lamps, the values in parentheses indicate the rated voltage of the lamps. Contact reliability FUJI has confirmed that the unit can be used in 1m circuit conditions at 5V C or DC. The operable range may vary depending on the ambient conditions and type of load. Fuji lectric F Components & ystems Co., td./d & C Catalog /141
Illuminated Pushbuttons 164 and 165 Illuminated pushbutton switches/without transformer Operator amp Voltage Contact Momentary action lternate action 164 type 165 (Oil-tight) type 164 type 165 (Oil-tight) type xtended round head Flat D V DC 164-113 165-113 164-5113 165-5113 164-223 165-223 164-5223 165-5223 164-333 165-333 164-5333 165-5333 pot D V DC 164-112 165-112 164-5112 165-5112 164-222 165-222 164-5222 165-5222 164-332 165-332 164-5332 165-5332 Incandes- V 164-11 165-11 164-511 165-511 cent C/DC 164-22 165-22 164-522 165-522 164-33 165-33 164-533 165-533 Neon 110V C 164-111 165-111 164-5111 165-5111 164-221 165-221 164-5221 165-5221 164-331 165-331 164-5331 165-5331 220V C 164-11M1 165-11M1 164-511M1 165-511M1 K-1103 164-22M1 165-22M1 164-522M1 165-522M1 164-33M1 165-33M1 164-533M1 165-533M1 Flush square head Flat D V DC 164-113 165-113 164-5113 165-5113 164-223 165-223 164-5223 165-5223 164-333 165-333 164-5333 165-5333 pot D V DC 164-112 165-112 164-5112 165-5112 164-222 165-222 164-5222 165-5222 164-332 165-332 164-5332 165-5332 Incandes- V 164-11 165-11 164-511 165-511 cent C/DC 164-22 165-22 164-522 165-522 164-33 165-33 164-533 165-533 Neon 110V C 164-111 165-111 164-5111 165-5111 164-221 165-221 164-5221 165-5221 164-331 165-331 164-5331 165-5331 220V C 164-11M1 165-11M1 164-511M1 165-511M1 164-22M1 165-22M1 164-522M1 165-522M1 K-1102 164-33M1 165-33M1 164-533M1 165-533M1 Flush rectangular head Flat D V DC 164-T113 165-T113 164-T5113 165-T5113 164-T223 165-T223 164-T5223 165-T5223 164-T333 165-T333 164-T5333 165-T5333 pot D V DC 164-T112 165-T112 164-T5112 165-T5112 164-T222 165-T222 164-T5222 165-T5222 164-T332 165-T332 164-T5332 165-T5332 Incandes- V 164-T11 165-T11 164-T511 165-T511 cent C/DC 164-T22 165-T22 164-T522 165-T522 164-T33 165-T33 164-T533 165-T533 Neon 110V C 164-T111 165-T111 164-T5111 165-T5111 164-T221 165-T221 164-T5221 165-T5221 164-T331 165-T331 164-T5331 165-T5331 220V C 164-T11M1 165-T11M1 164-T511M1 165-T511M1 164-T22M1 165-T22M1 164-T522M1 165-T522M1 K-1100 164-T33M1 165-T33M1 164-T533M1 165-T533M1 Note: eplace the mark by the button color code, see page /143. /142 Fuji lectric F Components & ystems Co., td./d & C Catalog
Illuminated Pushbuttons 164 and 165 Operator amp Voltage Contact Momentary action lternate action 164 type 165 (oil-tight) type 164 type 165 (oil-tight) type Flush rectangular head Flat D V DC 164-TG113 165-TG113 164-TG5113 165-TG5113 with guard 164-TG223 165-TG223 164-TG5223 165-TG5223 164-TG333 165-TG333 164-TG5333 165-TG5333 Incandes- V 164-TG11 165-TG11 164-TG511 165-TG511 cent C/DC 164-TG22 165-TG22 164-TG522 165-TG522 164-TG33 165-TG33 164-TG533 165-TG533 Neon 110V C 164-TG111 165-TG111 164-TG5111 165-TG5111 164-TG221 165-TG221 164-TG5221 165-TG5221 164-TG331 165-TG331 164-TG5331 165-TG5331 K-1101 220V C 164-TG11M1 165-TG11M1 164-TG511M1 165-TG511M1 164-TG22M1 165-TG22M1 164-TG522M1 165-TG522M1 164-TG33M1 165-TG33M1 164-TG533M1 165-TG533M1 Flush square head Flat D V DC 164-G113 165-G113 164-G5113 165-G5113 with guard 164-G223 165-G223 164-G5223 165-G5223 164-G333 165-G333 164-G5333 165-G5333 Incandes- V 164-G11 165-G11 164-G511 165-G511 cent C/DC 164-G22 165-G22 164-G522 165-G522 164-G33 165-G33 164-G533 165-G533 Neon 110V C 164-G111 165-G111 164-G5111 165-G5111 164-G221 165-G221 164-G5221 165-G5221 164-G331 165-G331 164-G5331 165-G5331 F90-301 220V C 164-G11M1 165-G11M1 164-G511M1 165-G511M1 164-G22M1 165-G22M1 164-G522M1 165-G522M1 164-G33M1 165-G33M1 164-G533M1 165-G533M1 Dimensions, mm, 5, 5 ø ø amp terminal 7 10 sq. amp terminal 7 10 sq. sq. T, T5 TG, TG5 G, G5 amp terminal 7 10 21 amp terminal 7 10 21 sq. sq. Button color Color Green ed White Yellow Blue Orange Code G W Y O amp voltage Voltages other than above are available Code D Incandescent Neon The color lens is made of a tinted transparent material. white illuminated pushbutton is fitted with a transparent color lens.(xcept the neon lamp) With wire-wrap pin terminals have a depth of 47mm. B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC 120V C 0V C Fuji lectric F Components & ystems Co., td./d & C Catalog /143
Illuminated Pushbuttons 164 and 165 Illuminated pushbutton switches/without transformer (ed/green D) Operator amp Voltage Contact Momentary action lternate action 164 type 165 (oil-tight) type 164 type 165 (oil-tight) type xtended round head ed/green V DC 164-G113 165-G113 164-5G113 165-5G113 D 164-G223 165-G223 164-5G223 165-5G223 K-1103 164-G333 165-G333 164-5G333 165-5G333 Flush square head ed/green V DC 164-G113 165-G113 164-5G113 165-5G113 D 164-G223 165-G223 164-5G223 165-5G223 K-1102 164-G333 165-G333 164-5G333 165-5G333 Flush rectangular head ed/green V DC 164-TG113 165-TG113 164-T5G113 165-T5G113 D 164-TG223 165-TG223 164-T5G223 165-T5G223 K-1100 Discontinued 164-TG333 165-TG333 164-T5G333 165-T5G333 Mar. 2007 Flush square head with ed/green V DC 164-GG113 165-GG113 164-G5G113 165-G5G113 guard D 164-GG223 165-GG223 164-G5G223 165-G5G223 F90-301 164-GG333 165-GG333 164-G5G333 165-G5G333 Flush rectangular head ed/green V DC 164-TGG113 165-TGG113 164-TG5G113 165-TG5G113 with guard D 164-TGG223 165-TGG223 164-TG5G223 165-TG5G223 K-1101 164-TGG333 165-TGG333 164-TG5G333 165-TG5G333 Note: The only color codes used for red/green Ds are and G. The color lens is transparent. ed/green Ds do not have high-brightness specifications. V DC only elationship between luminous color and terminal + b () ed Green Dimensions, mm ee Page /143 + a (+) imiting resistor /144 Fuji lectric F Components & ystems Co., td./d & C Catalog
Illuminated Pushbuttons 164 and 165 Illuminated pushbutton switches/with transformer Operator amp Voltage Contact Momentary action lternate action 164 type 165 (oil-tight) type 164 type 165 (oil-tight) type xtended round head Flat D Voltage 164-113 165-113 164-5113 165-5113 code F90-945 : 164-223 165-223 164-5223 165-5223 100-110V C Incandescent M: 164-11 165-11 164-511 165-511 200-220V C 164-22 165-22 164-522 165-522 Flush square head Flat D Voltage 164-113 165-113 164-5113 165-5113 code F90-946 : 164-223 165-223 164-5223 165-5223 100-110V Incandes- C 164-11 165-11 164-511 165-511 cent M: 200-220V C 164-22 165-22 164-522 165-522 Flush rectangular head Flat D Voltage 164-T113 165-T113 164-T5113 165-T5113 code F90-947 : 164-T223 165-T223 164-T5223 165-T5223 100-110V C Incandescent M: 164-T11 165-T11 164-T511 165-T511 200-220V C 164-T22 165-T22 164-T522 165-T522 Flush rectangular head Flat D Voltage 164-TG113 165-TG113 164-TG5113 165-TG5113 with guard code : 164-TG223 165-TG223 164-TG5223 165-TG5223 100-110V C Incandes- 164-TG11 165-TG11 164-TG511 165-TG511 cent M: 200-220V F90-941 C 164-TG22 165-TG22 164-TG522 165-TG522 Flush square head Flat D Voltage 164-G113 165-G113 164-G5113 165-G5113 with guard code : 164-G223 165-G223 164-G5223 165-G5223 100-110V C Incandes- 164-G11 165-G11 164-G511 165-G511 cent M: 200-220V F90-948 C 164-G22 165-G22 164-G522 165-G522 Note: eplace the mark by the button color code, see page /146. Fuji lectric F Components & ystems Co., td./d & C Catalog /145
Illuminated Pushbuttons 164 and 165 Dimensions, mm 62, 5, 5 62 Insulation cover () b (+) a 7 10 ø ø 32 Insulation cover () b (+) a 7 10 32 Transformer primary terminal 48.5 older Transformer unit Transformer primary terminal older 48.5 Transformer unit 62 T, T5 TG, TG5 G, G5 62 () b Insulation cover (+) a 7 10 32 Insulation cover (+) a 7 10 32 32 Transformer primary terminal older 48.5 Transformer unit Transformer primary terminal older 48.5 Transformer unit Button color Color Green ed White Yellow Blue Orange Code G W Y O The color lens is made of a tinted transparent material. /146 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons 164 and 165 Pushbutton switches Operator Contact Momentary action lternate action Dimensions, mm 164 type 165 (oil-tight) type 164 type 165 (oil-tight) type xtended round head 164-11 165-11 164-511 165-511 164-22 165-22 164-522 165-522 φ φ K-1103 164-33 165-33 164-533 165-533 7 10 sq. Flush square head 164-F11 165-F11 164-F511 165-F511 164-F22 165-F22 164-F522 165-F522 K-1102 164-F33 165-F33 164-F533 165-F533 7 10 sq. sq. Flush rectangular head 164-TF11 165-TF11 164-TF511 165-TF511 164-TF22 165-TF22 164-TF522 165-TF522 K-1100 164-TF33 165-TF33 164-TF533 165-TF533 7 10 21 Flush rectangular head with guard 164-TGF11 165-TGF11 164-TGF511 165-TGF511 164-TGF22 165-TGF22 164-TGF522 165-TGF522 K-1101 164-TGF33 165-TGF33 164-TGF533 165-TGF533 7 10 21 Flush square head with guard 164-GF11 165-GF11 164-GF511 165-GF511 164-GF22 165-GF22 164-GF522 165-GF522 F90-301 164-GF33 165-GF33 164-GF533 165-GF533 7 10 sq. sq. Mushroom head 164-M11 165-M11 164-M511 165-M511 164-M22 165-M22 164-M522 165-M522 φ 23.5 K-1136 164-M33 165-M33 164-M533 165-M533 16.5 Convex square head 164-M11 165-M11 164-M511 165-M511 164-M22 165-M22 164-M522 165-M522 23.5 sq. K-1134 164-M33 165-M33 164-M533 165-M533 16.5 Convex rectangular head 164-TM11 165-TM11 164-TM511 165-TM511 164-TM22 165-TM22 164-TM522 165-TM522 17.5 K-1135 164-TM33 165-TM33 164-TM533 165-TM533 16.5 23.5 Button color eplace the mark by the following color code Color Green ed Black White Blue Yellow Orange Code G B W Y O Fuji lectric F Components & ystems Co., td./d & C Catalog The color lens is made of a tinted transparent material. (xcept the M, M, TM types) white pushbutton is fitted with a transparent color lens.(xcept the M, M, TM types) black pushbutton consists of a transparent color lens and an attached black legend plate. (xcept M, M, TM types) With wire-wrap pin terminals have a depth of 47mm. /147
Pushbuttons 165 Pushbutton switches (Direct opening action) Operator Button Contact Terminal 165 (oil-tight) type Dimensions, mm color Push-lock, turn-reset ed 1NC older/tab 165-V01 (32mm dia.) older (165-V01-) ø32 F91-584 2NC 165-V02 (165-V02-).5.5 *(20) Push-lock, turn-reset 1NC 165-V101 (40mm dia.) (165-V101-) ø40 F91-583 2NC 165-V102 (165-V102-).5.5 *(20) Notes: * ( ) For switch with solder terminal. Contact arrangements indicated in the table can be supplied. Product with no trigger action mechanism. mergency stop pushbutton switches (Direct opening action), conform to N4 Operator Button Contact Terminal 165 (oil-tight) type Dimensions, mm color Push-lock, turn-reset ed 1NC older/tab 165-V501 (32mm dia.) older (165-V501-) 6 (max.) ø32 F97-232 2NC 165-V502 (165-V502-) 33 42.5 * (37.5) Push-lock, turn-reset 1NC 165-V601 (40mm dia.) (165-V601-) 6 (max.) ø40 F97-231 2NC 165-V602 (165-V602-) 33 42 * (37.5).5 Notes: * ( ) For switch with solder terminal. Contact arrangements indicated in the table can be supplied. /148 Fuji lectric F Components & ystems Co., td./d & C Catalog
elector witches 164 and 165 elector switches/2-position (90-degree) Operator Operation Key Contact 164 type 165 Dimensions, mm removable (oil-tight) type position Knob with Maintained 164-P2B11 165-P2B11 rectangular bezel 164-P2B22 165-P2B22 164-P2B33 165-P2B33 pring 164-P0B11 165-P0B11 return 164-P0B22 165-P0B22 F89-564 164-P0B33 165-P0B33 Knob with square Maintained 164-P2B11 165-P2B11 bezel 164-P2B22 165-P2B22 164-P2B33 165-P2B33 pring 164-P0B11 165-P0B11 return 164-P0B22 165-P0B22 F89-563 164-P0B33 165-P0B33 Key with Maintained 164-J211 165-J211 rectangular bezel 164-J222 165-J222 164-J233 165-J233 164-J2B11 165-J2B11 Fuji lectric F Components & ystems Co., td./d & C Catalog 164-J2B22 165-J2B22 B 164-J2B33 165-J2B33 164-J2D11 165-J2D11 164-J2D22 165-J2D22 D 164-J2D33 165-J2D33 pring 164-J011 165-J011 return 164-J022 165-J022 F89-561 164-J033 165-J033 Key with square Maintained 164-J211 165-J211 bezel 164-J222 165-J222 164-J233 165-J233 164-J2B11 165-J2B11 F89-562 The operating angle range can be changed as shown below by setting the attached flange shifted by 45 in combination with the contact block. In this case, the minimum mounting pitch is 26mm because the contact block is shifted by 45 from the flange. There are 6 available key types;, B, C, D, and F. tandard key code is. With wire-wrap pin terminals have a depth of 47mm. 164-J2B22 165-J2B22 B 164-J2B33 165-J2B33 164-J2D11 165-J2D11 164-J2D22 165-J2D22 D 164-J2D33 165-J2D33 pring 164-J011 165-J011 return 164-J022 165-J022 164-J033 165-J033 Contact block position 8.5 10.5.5 8.5 10.5.5 Contact arrangement and operator position: 2-position selector switch Contact arrange- ment U Operator eft M U position M ight 3-position selector switch Contact arrange- ment Operator eft U U M position Center ight M φ 8.5 10.5 φ 25.5 8.5 10.5 25.5 U φ sq. sq. U M /149
elector witches 165 elector switches/2-position (90-degree) (Direct opening action) Operator Operation Key Contact 165 (oil-tight) type Dimensions, mm removable position Key with rectangular Maintained 165-JM211 bezel B 165-JM2B11 F95-57 D 165-JM2D11 165-JM222 32.5 8.8 41.5 10.8 25.5 B 165-JM2B22 F97-334 D 165-JM2D22 Key with round bezel Maintained 165-JM211 4(max.) B 165-JM2B11 20 φ sq. D 165-JM2D11 165-JM222 32.5 41.5 9.8 10.8 25.5 4(max.) F99-320 B D 165-JM2B22 165-JM2D22 37.5 46.5 9.8 10.8 25.5 20 φ sq. 27.5 There are 6 available key types;, B, C, D, and F. tandard key code is. Contact arrangement and operator positions: 2-position selector switch Contact arrangement Operator position eft Terminal number U: Upper contact block 11 12 11 12 22 ight 11 12 22 21 22 : ower contact block Contact arrangement Operator position eft U 11 12 11 12 ight 22 11 12 22 11 12 22 22 /0 Fuji lectric F Components & ystems Co., td./d & C Catalog
elector witches 164 and 165 elector switches/3-position (90-degree) Operator Operation Key Contact 164 type 165 Dimensions, mm removable (oil-tight) type position Knob with Maintained 164-P3B22 165-P3B22 rectangular bezel 164-P3B33 165-P3B33 pring/ 164-P6B22 165-P6B22 manual return 164-P6B33 165-P6B33 pring/ 164-P7B22 165-P7B22 manual return 164-P7B33 165-P7B33 pring return 164-P1B22 165-P1B22 K-1099 164-P1B33 165-P1B33 Knob with square Maintained 164-P3B22 165-P3B22 bezel 164-P3B33 165-P3B33 pring/ 164-P6B22 165-P6B22 manual return 164-P6B33 165-P6B33 pring/ 164-P7B22 165-P7B22 manual return 164-P7B33 165-P7B33 pring return 164-P1B22 165-P1B22 K-1133 164-P1B33 165-P1B33 Key with Maintained* 164-J322 165-J322 rectangular bezel 164-J333 165-J333 164-J322 165-J322 164-J333 165-J333 164-J3D22 165-J3D22 D 164-J3D33 165-J3D33 164-J3C22 165-J3C22 C 164-J3C33 165-J3C33 pring/ 164-J622 165-J622 manual return 164-J633 165-J633 D 164-J6D22 165-J6D22 164-J6D33 165-J6D33 pring/ 164-J722 165-J722 manual return 164-J733 165-J733 164-J722 165-J722 164-J733 165-J733 pring 164-J122 165-J122 K-1098 return 164-J133 165-J133 Key with square Maintained* 164-J322 165-J322 bezel 164-J333 165-J333 D C 164-J322 164-J3D22 164-J3C22 165-J322 165-J3D22 165-J3C22 164-J333 164-J3D33 164-J3C33 165-J333 165-J3D33 165-J3C33 pring/ 164-J622 165-J622 manual return 164-J633 165-J633 D 164-J6D22 165-J6D22 164-J6D33 165-J6D33 pring/ 164-J722 165-J722 manual return 164-J733 165-J733 164-J722 165-J722 164-J733 165-J733 pring 164-J122 165-J122 K-1132 return 164-J133 165-J133 8.5 10.5.5 8.5 10.5.5 φ 8.5 10.5 φ 25.5 8.5 10.5 25.5 sq. sq. There are 6 available key types;, B, C, D, and F. tandard key code is. Contact arrangement and operator position: ee page /149. pring return, spring/manual return (spring return): Operation angle 70-degree * vailable key removable position: Code B With wire-wrap pin terminals have a depth of 47mm. Fuji lectric F Components & ystems Co., td./d & C Catalog /1
elector witches 164 and 165 elector switches/3-position (45-degree) Operator Operation Key Contact 164 type 165 Dimensions, mm removable (oil-tight) type position Knob with Maintained 164-PK3B22 165-PK3B22 rectangular bezel 164-PK3B33 165-PK3B33 pring/ 164-PK6B22 165-PK6B22 manual return 164-PK6B33 165-PK6B33 pring/ 164-PK7B22 165-PK7B22 manual return 164-PK7B33 165-PK7B33 pring return 164-PK1B22 165-PK1B22 K-1099 164-PK1B33 165-PK1B33 Knob with square Maintained 164-PK3B22 165-PK3B22 bezel 164-PK3B33 165-PK3B33 pring/ 164-PK6B22 165-PK6B22 manual return 164-PK6B33 165-PK6B33 pring/ 164-PK7B22 165-PK7B22 manual return 164-PK7B33 165-PK7B33 pring return 164-PK1B22 165-PK1B22 K-1133 164-PK1B33 165-PK1B33 Key with Maintained 164-JK322 165-JK322 rectangular bezel 164-JK333 165-JK333 164-JK322 165-JK322 164-JK333 165-JK333 164-JK3D22 165-JK3D22 D 164-JK3D33 165-JK3D33 164-JK3C22 165-JK3C22 C 164-JK3C33 165-JK3C33 pring/ 164-JK622 165-JK622 manual return 164-JK633 165-JK633 D 164-JK6D22 165-JK6D22 164-JK6D33 165-JK6D33 pring/ 164-JK722 165-JK722 manual return 164-JK733 165-JK733 164-JK722 165-JK722 164-JK733 165-JK733 pring 164-JK122 165-JK122 K-1098 return 164-JK133 165-JK133 Key with square Maintained 164-JK322 165-JK322 bezel 164-JK333 165-JK333 D C 164-JK322 165-JK322 164-JK3D22 165-JK3D22 164-JK3C22 165-JK3C22 164-JK333 165-JK333 164-JK3D33 165-JK3D33 164-JK3C33 165-JK3C33 pring/ 164-JK622 165-JK622 manual return 164-JK633 165-JK633 D 164-JK6D22 165-JK6D22 164-JK6D33 165-JK6D33 pring/ 164-JK722 165-JK722 manual return 164-JK733 165-JK733 164-JK722 165-JK722 164-JK733 165-JK733 pring 164-JK122 165-JK122 K-1132 return 164-JK133 165-JK133 8.5 10.5.5 8.5 10.5.5 φ 8.5 10.5 φ 25.5 8.5 10.5 25.5 sq. sq. There are 6 available key types;, B, C, D, and F. tandard key code is. Contact arrangement and operator position: ee page /3. /2 Fuji lectric F Components & ystems Co., td./d & C Catalog
elector witches 164 and 165 Key removable positions (JK, JK) emvable position Code B C D F G Operation code 3 6 7 1 Key removable position, B, C, D,, F, G D,, F,, G Key code No. There are 6 available key types;, B, C, D, and F. tandard key code is. Contact block position Contact arrangement and operator position: 3-position selector switch Contact arrange- ment Operator eft U U M position Center ight Fuji lectric F Components & ystems Co., td./d & C Catalog /3
Pilot ights 164 and 165 Pilot lights/without transformer ens amp Voltage 164 type 165 (oil-tight) type Dimensions, mm xtended round Flat D V DC 164-Z3 165-Z3 pot D V DC 164-Z2 165-Z2 ed/green D V DC 164-ZG3 165-ZG3 Discontinued Mar. 2007 Incandescent V C/DC 164-Z 165-Z Neon 110V C 164-Z1 165-Z1 220V C 164-ZM1 165-ZM1 Discontinued Mar. 2007 Discontinued Mar. 2007 Discontinued Mar. 2007 Flush square Flat D V DC 164-Z3 165-Z3 Flush rectangular K-1139 K-1138 K-1137 pot D V DC 164-Z2 165-Z2 ed/green D V DC 164-ZG3 165-ZG3 Incandescent V C/DC 164-Z 165-Z Discontinued Mar. 2007 Neon 110V C 164-Z1 165-Z1 220V C 164-ZM1 165-ZM1 Flat D V DC 164-ZT3 165-ZT3 pot D V DC 164-ZT2 165-ZT2 Discontinued Mar. 2007 ed/green D V DC 164-ZTG3 165-ZTG3 Incandescent V C/DC 164-ZT 165-ZT Neon 110V C 164-ZT1 165-ZT1 220V C 164-ZTM1 165-ZTM1 Dome D 12V DC 165-ZMB2 F87-45 V DC 165-ZM2 a (+) b () a (+) b () a (+) b () a (+) amp terminal 1sq. b () 1sq. 7 10 ø ø sq. sq. sq. 7 sq. 10 sq. 7 10 16 14 6.7 31.3 14.2 21 5 (max.) ø ø D sq. Note: The only color codes used for red/green Ds are and G. The color lens is transparent. ed/green Ds do not have high-brightness specifications. elationship between luminous color and terminal + b () + Discontinued a (+) ed Green imiting resistor Mar. 2007 amp voltage Voltages other than above are available Code D Incandescent B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC Note: xcept for ZM types and red/green D types Neon 120V C 0V C ens color eplace the mark by the following lens color code Color Green ed White Yellow Blue Orange Code G W Y O The color lens is made of a tinted transparent material. white pilot lights is fitted with a transparent color lens. (xcept the neon lamp and dome). With wire-wrap pin terminals have a depth of 29mm. (xcept for ZM type) /4 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pilot ights 164 and 165 Pilot lights/with transformer ens amp Voltage 164 type 165 (oil-tight) type Dimensions, mm xtended square F90-944 Voltage Flat D : 164-Z3 165-Z3 100-110V C M: 200-220V Incandescent C 164-Z 165-Z Insulation cover Transformer primary terminal 62 () b (+) a 48.5 7 10 Transformer unit ø ø older 32 Flush square F90-943 Voltage Flat D : 164-Z3 165-Z3 100-110V C M: 200-220V Incandescent C 164-Z 165-Z Insulation cover Transformer primary terminal 62 () b (+) a 48.5 Transformer unit 7 10 sq. sq. older 32 Flush rectangular F90-942 Flat D Voltage : 164-ZT3 165-ZT3 100-110V C M: 200-220V Incandescent C 164-ZT 165-ZT Insulation cover Transformer primary terminal 62 () b (+) a 48.5 Transformer unit 7 10 older 32 21 ens color eplace the mark by the following lens color code Color Green ed White Yellow Blue Orange Code G W Y O The color lens is made of a tinted transparent material. white pilot lights is fitted with a transparent color lens. Fuji lectric F Components & ystems Co., td./d & C Catalog /5
Buzzers 164 and 165 Buzzers ound Operating voltage Type Dimensions, mm tandard 6V C 164-TXBC hort-circuit terminal Connected: Intermittent sound Not connected: Continuous sound 6V DC 164-TXBDC b () a (+) 12 to V C/DC 164-TXB 6 (max.) 7 21 F87-317 35 to 48V C/DC 164-TXBF 7.5 34.5 Terminal: Tab/solder type 10 Maximum panel thickness for the buzzers with washers is 5mm oud sound 6V C 6V DC 164-TX1BC 164-TX1BDC hort-circuit terminal Connected: Intermittent sound Not connected: Continuous sound b () 12 to V C/DC 164-TX1B a (+) 5 (max.) 10 21 F87-44 35 to 48V C/DC 164-TX1BF 7.5 37.5 oud sound with volume control 6V C/DC 164-TX2B hort-circuit terminal Connected: Intermittent sound Not connected: Continuous sound Volume Clockwise: Increase sound pressure Counterclockwise: Decrease sound pressure 12 to V C/DC 164-TX2B F93-297 35 to 48V C/DC 164-TX2BF 9 29.5 16 Panel thickness 5 (max.) D (red) tandard sound with volume control (IP54) 6V C/DC 165-XB Volume Clockwise: Increase sound pressure Counterclockwise: Decrease sound pressure hort-circuit terminal Connected: Intermittent sound Not connected: Continuous sound 12 to V C/DC 165-XB Panel thickness 5 (max.) F96-3 35 to 48V C/DC 165-XBF 9 37.5 ø /6 Fuji lectric F Components & ystems Co., td./d & C Catalog
Numerical Indicators 164 and 165 Numerical indicators Display Input logic Operating voltage Description 164 type 165(oil-tight) type Dimensions, mm Without decimal decoder node 164-T 165-T Terminal ø1 5 (max.) 5.6 P-165 Cathode 164-T C 165-T C 12 5 22 40 10 3 10 21 With decimal decoder (5, 12, V) F87-3 Positive (ow active) 5V DC 5V DC 12V DC V DC Decoder type: 7447 Decoder type:4511 164-TC1 164-TC4 164-TC4 164-TC4 B C 165-TC1 165-TC4 165-TC4 165-TC4 B C 12 4 Terminal ø0.8 5 (max.) 60 70 10 21 10 3 5.6 With decimal decoder (V) Positive V DC Decoder type:4511 164-TC4 -K 165-TC4 -K Without connector 2.54 60 F89-948 Negative 164-TC4 -NK 165-TC4 -NK With sign decoder (±1 display) Positive V DC Decoder type:4511 164-TC4-1K 165-TC4-1K With connector 48 42 34 32 11 30 32 11 2.54 Terminal ø1 3 10 76.5 5 (max.) 40 3 10 7 F88-1093 Negative 164-TC4-1NK 165-TC4-1NK ø3.3 7 13.5 91 7 uminous color eplace the mark by the luminous color code : ed G: Green Connector eplace the mark by the connector code Blank: Without connector 1: With connector Fuji lectric F Components & ystems Co., td./d & C Catalog /7
Numerical Indicators 164 and 165 Without decoder, with decoder (5, 12 V) Wiring diagrams Without decoder/164-t, 165-T With decoder (5, 12, V) / 164-TC1, 165-TC1, 164-TC4, 165-TC4 DP c g b com a f com e d node common (7seg.D) a f b e d g c DP 7seg. decoder Terminal 164-TC1 No. 165-TC1 164-TC4 165-TC4 10 VCC(5v) VDD(5,12,V) 1 5 4 7 3 8 2 9 6 B BCD C code D T BI/BO BI GND (0V) D.P B BCD C code D T BI Vss (0V) D.P a f b e g c d DP The illustration shows the anode common type. The D of the cathode common type is connected in the opposite direction. Note: s shown in the illustration, the structure of the T type consists of a 7-segment D provided with a casing only. imilar to a standard single 7-segment D, use the T type with a current limiting resistor connected. 10.16 2.54 1 2 3 4 5 2.54 6 7 8 9 10 Truth value chart 164-TC1, 165-TC1 BCD input (positive) D C B Note: Input BI BI/BO (OUT) Operates independently from and signals. T Display xtinguish xtinguish xtinguish 164-TC4, 165-TC4 BCD input (positive) D C B Note: Input BI T Operates independently from and signals. Display xtinguish xtinguish xtinguish xtinguish xtinguish xtinguish xtinguish atch BCD input voltage Type 164-TC1, 165-TC1 164-TC4, 165-TC4 Input current () Type BI BI/BO 164-TC1, 165-TC1 1.6m max. 2.4m max. Note: When the pin is set to, the D.P. will be lit. /8 Type 164-TC4, 165-TC4 164-TC4 B, 165-TC4 B 164-TC4 C, 165-TC4 C Note: pull-up resistor is built-in. Input voltage 5V 0 to 0.4V 2.4 to 5V 0 to 1.5V 3.5 to 5V BI, T, ±0.6m max. ±0.2m max. ±0.2m max. 12V 0 to 3V 9 to 12V V 0 to 4V 11 to V T 1.6m max. Terminal symbol T (amp Test): ll segments other than the decimal point will turn ON by setting this pin to (i.e., 8 is displayed). BI (ipple Blanking Input): etting this pin to will turn the display OFF when all BCD codes are. BI/BO (Blanking Input/ipple Blanking Output): I/O pin etting this pin to will turn the display OFF regardless of the BCD codes. This pin will be when all BCD codes are. (atch nable): When this pin is set to, data will pass through. When it is set to, data will be retained. Connect this pin to (0V) when not in use. BI (Blanking Input): When this pin is set to, the display will be OFF for all input except T. D.P. (Decimal Point) Fuji lectric F Components & ystems Co., td./d & C Catalog
Numerical Indicators 164 and 165 pplication to PC Used with 164-TC1, 165-TC1 164-TC1 B, 165-TC4 B 164-TC1 C, 165-TC4 C Note: Input logic Positive (low active) Output from PC Transistor output (source) PNP Transistor output (sink) NPN vailable, not available s 16 -TC1, -TC4 B, and -TC4 C (5V, 12V, and V models) do not have an inverter circuit inside, use a programmable logic controller, inserting an inverter (reverse) instruction on your program. (ow ctive) With decoder (V) Wiring diagrams With decoder/164-tc4, 165-TC4 With decoder/164-tc4-1, 165-TC4-1 1 2 3 4 5 6 7 8 9 10 11 Decoder circuit Voltage stabilizer circuit Input circuit Terminal No. 1 8 4 3 7 5 6 10.11 VDD (V) B C D D.P Vss (0V) BCD code Decoder circuit Voltage stabilizer circuit Input circuit Terminal No. 1 8 4 3 5 10.11 VDD (V) B C Vss (0V) BCD code Truth value chart Decimal display Positive Negative Display D C B D C B xtinguish xtinguish xtinguish xtinguish xtinguish xtinguish atch Note: Operates independently from and signals. Terminal symbol. (atch nable): olds the last entry when the positive logic type goes to () and the negative logic type goes to (). D.P (Decimal Point): Displays a decimal point when the positive logic type goes to () and the negative logic goes to (). ±1 display Positive Negative Display C B C B xtinguish xtinguish atch Note: Operates independently from and signals. BCD input voltage 0 to 2V 12 to 30V pplication to PC Used with Input logic 164-TC4 Positive 165-TC4 164-TC4 -N Negative 165-TC4 -N Note: vailable, not available Input current () Positive logic 2m max. Negative logic 4m max. Output from PC Transistor output (source) PNP Transistor output (sink) NPN Fuji lectric F Components & ystems Co., td./d & C Catalog /9
Pushbuttons/electors/Pilot ights/buzzers 164 and 165 Mounting space Mounting space, mm Pushbuttons and pilot lights xtended round head or lens Flush square head or lens Flush rectangular head or lens 20 20 Panel cutting ø16.2 +0.2 0 20 Panel cutting ø16.2 +0.2 0 Panel cutting ø16.2 +0.2 0 Mushroom head Convex square head Convex rectangular head 20 Panel cutting ø16.2 +0.2 0 Panel cutting ø16.2 +0.2 0 Panel cutting ø16.2 +0.2 0 elector switches When mounting the selector switches near the pilot light When mounting the selector switches near each other With transformer Panel cutting ø16.2 +0.2 0 20 42 Panel cutting ø16.2 +0.2 0 21.5 ()* When mounting the JM or JM selector switches near each other ( only) When mounting the JM or JM selector switches near the other selector switch, pushbutton switch and pilot lights Note: *( ) For switch with flush rectangular head 30 25 * 165-V, V1, V5, V6 7.7±0.1 0 ø16.2 +0.2 ø2 +0.1 0 Note: * Mushroom, convex square, convex rectangular: 27 165-JM, JM 0 ø16.2 +0.2 +0.2 0 Terminal number 164, 165 Type Wiring Illuminated pushbuttons Pushbuttons elector switches (except for JM, JM types) Pilot lights (without transformer) a (+) 1 3 1 3 a (+) b (-) 2 4 2 4 b (-) Terminal position Type number display side 3 1 3 1 3 1 b (-) a (+) 2 4 2 4 2 4 Type number display side a b /160 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights 165-2 Type number nomenclature Type number nomenclature Pushbuttons, illuminated pushbuttons and pilot lights 165-2 F 11 3 W ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 165-2: Oil-tight (arge operator) ➁ Operator or lens Operator for illuminated pushbutton F: Flush round head F5: Flush round head (lternate) F: Flush square head F5: Flush square head (lternate) : xtended round head 5: xtended round head (lternate) : xtended square head 5: xtended square head (lternate) C: Concave square head C5: Concave square head (lternate) M: Mushroom head YM: Mushroom head with square bezel V: Push-lock, turn-reset YV: Push-lock, turn-reset with square bezel Operator for pushbuttons F: Flush round head F5: Flush round head (lternate) F: Flush square head F5: Flush square head (lternate) : xtended round head 5: xtended round head (lternate) : xtended square head 5: xtended square head (lternate) C: Concave square head C5: Concave square head (lternate) M: Mushroom head YM: Mushroom head with square bezel V: Push-lock, turn-reset YV: Push-lock, turn-reset with square bezel 2: With selector ring Y2: With selector ring with square bezel ens for pilot lights Z: Flush round Z: Flush square Z: xtended round Z: xtended square ➂ Color of button or lens Code G B Y W O Color Green ed Black* Yellow White Blue Orange Notes: ( ): indicates luminous color * Not available for illuminated types ➃ Contact arrangement (except pilot lights) 11: 22: 33: ➄ amp voltage ➅ Type of lamp Blank: Incandescent 1: Neon 3: Flat D ➆ Terminal Blank: older/tab W: Wire-wrap Button D Incandescent (Orange) (mber) Code D Incandescent Neon B K M P 5V DC 6V DC 12V DC V DC 5V C/DC 12V C/DC V C/DC Neon (Orange) (Orange) (Orange) (Green) 110V C 120V C 220V C 0V C Fuji lectric F Components & ystems Co., td./d & C Catalog /161
Pushbuttons/electors/Pilot ights 165-2 Type number nomenclature Type number nomenclature elector switches 165-2 J 2 B 11 W ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 165-2: Oil-tight (arge operator) ➁ Operator Knob and key type 2-position (operating angle 90 ) P: Knob YP: Knob with square bezel J: Key YJ: Key with square bezel 3-position (operating angle 45 ) P: Knob YP: Knob with square bezel J: Key YJ: Key with square bezel ever type 2-position (operating angle 45 ) : ever : ever with square bezel Note: The operation angle is 45 on the upper and lower side. ➂ Operation 2: 2-position, maintained 0: 2-position, spring return* 3: 3-position, maintained 6: 3-position, spring/manual return (eft to center) 7: 3-position, spring/manual return (ight to center) 1: 3-position, spring return Note: * xcept for and types ➃ Color of knob, lever or key removable position Color of knob or lever B: Black Key removable position Code 2-position 3-position B C D F G 2 0 1 3 6 7 Illuminated selector switches 165-2 P 2 G 11 3 ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➀ Product category 165-2: Oil-tight (arge operator) ➁ Operator 2-position (operating angle 90 ) P: Knob 3-position (operating angle 45 ) P: Knob ➂ Operation 2: 2-position, maintained 3: 3-position, maintained ➃ Color of knob Code G Y W O Color Green ed Yellow White Blue Orange D (Orange) (mber) Notes: ( ): indicates luminous color The part other than the arrow of the knob is black. ➄ Contact arrangement 11: * 22: Note: * xcept for 3-position ➅ amp voltage Incandescent Code D Incandescent Neon B K M P 5V DC 6V DC 12V DC V DC ➆ Type of lamp Blank: Incandescent 1: Neon 3: Flat D Note: Terminal with solder/tab only 5V C/DC 12V C/DC V C/DC Neon (Orange) (Orange) (Orange) (Green) 110V C 120V C 220V C 0V C ➄ Contact arrangement 11: * 22: 33: Note: * xcept for 3-position ➅ Key type No. (standard), B, C, D,, F ➆ Terminal Blank: older/tab W: Wire-wrap /162 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights 165-2 atings and specifications tandards approved U508 C C22.2 No.14 TÜV: N60947-5-1 File No. 44592 File No. 279 (except for 165-2Z, 2Z, 2Z, 2Z) File No. 84365 (for 165-2Z, 2Z, 2Z, 2Z) Pushbutton, illuminated pushbutton: 9250087 elector (except for 165-2, ), illuminated selector: 9250088 elector (for 165-2, ): 9250087 Pilot lights: 9250089 pecifications (Indoor use) Item 165-2 ated insulation voltage 250V C/DC mbient temperature 10 to +70 C * 1 (no condensation or no icing) umidity 45 to 85% (at 5 to +40 C), no condensation or no icing Durability Mechanical Pushbutton and illuminated pushubutton switch (operations) Momentary action: 1 million lternate action: 250,000 Push-lock, turn-reset: 100,000 With selector ring: 250,000 elector and illuminated selector switch: 250,000* 2 lectrical 100,000 (220V C 0.7) Dielectric strength 2000V C, 1 minute (Between lamp and contact terminals: 00V C, 1 minute) Conditional short-circuit current 1000 hort-circuit protective device Fuse 1 Pollution degree 3 Vibration esonance: 10 to 55z, double amplitude 0.1mm Constant: 16.7z, double amplitude 3mm hock Malfunction durability: 100m/s 2 Mechanical durability: 500m/s 2 Operating frequency 1200 operation/hour (on-load factor: 40%) Insulation resistance 100MΩ or more (500V DC megger) Operator protection IP65 Notes: * 1 For illuminated pushbutton, illuminated selector switch and pilot light: 10 to +55 C * 2 Key insertion/removal durability for selector switch key types: 10,000 Contact ratings ee page /141 amp ratings ated operational voltage 5V 6V 12V V 110V 120V 220V 0V Consumption D DC 14m (Yellow: 28m) 14m (Yellow: 28m) 14m 14m Incandescent C/DC 0.45W (6V) 0.55W (14V) 0.55W (28V) Neon C 0.19V 0.21V 0.38V 0.42V Notes: For the incandescent lamps, the values in parentheses indicate the rated voltage of the lamps. Contact reliability FUJI has confirmed that the unit can be used in 1m circuit conditions at 5V C or DC. The operable range may vary depending on the ambient conditions and type of load. Fuji lectric F Components & ystems Co., td./d & C Catalog /163
Illuminated Pushbutton witches 165-2 Illuminated pushbutton switches Operator amp Voltage Contact Momentary action Type Flush round head F87-211 xtended round head F87-210 Mushroom head F87-221 Mushroom head with square bezel F87-220 Flat D Incandescent Neon Flat D Incandescent Neon Flat D Incandescent Neon Flat D Incandescent Neon V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C Note: eplace the mark by the following color code, see page /166. 165-2F113 165-2F223 165-2F333 165-2F11 165-2F22 165-2F33 165-2F111 165-2F221 165-2F331 165-2F11M1 165-2F22M1 165-2F33M1 165-2113 165-2223 165-2333 165-211 165-222 165-233 165-2111 165-2221 165-2331 165-211M1 165-222M1 165-233M1 165-2M113 165-2M223 165-2M333 165-2M11 165-2M22 165-2M33 165-2M111 165-2M221 165-2M331 165-2M11M1 165-2M22M1 165-2M33M1 165-2YM113 165-2YM223 165-2YM333 165-2YM11 165-2YM22 165-2YM33 165-2YM111 165-2YM221 165-2YM331 165-2YM11M1 165-2YM22M1 165-2YM33M1 lternate action Type 165-2F5113 165-2F5223 165-2F5333 165-2F511 165-2F522 165-2F533 165-2F5111 165-2F5221 165-2F5331 165-2F511M1 165-2F522M1 165-2F533M1 165-25113 165-25223 165-25333 165-2511 165-2522 165-2533 165-25111 165-25221 165-25331 165-2511M1 165-2522M1 165-2533M1 Dimensions, mm 1 to 5 1 to 5 11.5 ø20 ø25 1 to 5 1 to 5 11.5 ø20 ø25 11.5 22 11.5 22 ø32 ø32 25sq. /164 Fuji lectric F Components & ystems Co., td./d & C Catalog
Illuminated Pushbutton witches 165-2 Illuminated pushbutton switches Operator amp Voltage Contact Momentary action Type Flush square head F87-201 xtended square head F87-200 Concave square head F87-199 Flat D Incandescent Neon Flat D Incandescent Neon Flat D Incandescent Neon V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C Note: eplace the mark by the following color code, see page /166. 165-2F113 165-2F223 165-2F333 165-2F11 165-2F22 165-2F33 165-2F111 165-2F221 165-2F331 165-2F11M1 165-2F22M1 165-2F33M1 165-2113 165-2223 165-2333 165-211 165-222 165-233 165-2111 165-2221 165-2331 165-211M1 165-222M1 165-233M1 165-2C113 165-2C223 165-2C333 165-2C11 165-2C22 165-2C33 165-2C111 165-2C221 165-2C331 165-2C11M1 165-2C22M1 165-2C33M1 lternate action Type 165-2F5113 165-2F5223 165-2F5333 165-2F511 165-2F522 165-2F533 165-2F5111 165-2F5221 165-2F5331 165-2F511M1 165-2F522M1 165-2F533M1 165-25113 165-25223 165-25333 165-2511 165-2522 165-2533 165-25111 165-25221 165-25331 165-2511M1 165-2522M1 165-2533M1 165-2C5113 165-2C5223 165-2C5333 165-2C511 165-2C522 165-2C533 165-2C5111 165-2C5221 165-2C5331 165-2C511M1 165-2C522M1 165-2C533M1 Dimensions, mm 1 to 5 1 to 5 11.5 25sq. 1 to 5 11.5 25sq. 11.5 20sq. 16.5 25sq. 20sq. 20sq. Fuji lectric F Components & ystems Co., td./d & C Catalog /165
Illuminated Pushbutton witches 165-2 Illuminated pushbutton switches Operator amp Voltage Contact Type Dimensions, mm Push-lock, turn-reset F87-219 Push-lock, turn-reset with square bezel F87-2 Flat D Incandescent Neon Flat D Incandescent Neon V DC V C/DC 110V C 220V C V DC V C/DC 110V C 220V C 165-2V113 165-2V223 165-2V333 165-2V11 165-2V22 165-2V33 165-2V111 165-2V221 165-2V331 165-2V11M1 165-2V22M1 165-2V33M1 165-2YV113 165-2YV223 165-2YV333 165-2YV11 165-2YV22 165-2YV33 165-2YV111 165-2YV221 165-2YV331 165-2YV11M1 165-2YV22M1 165-2YV33M1 1 to 5 1 to 5 11.5 22 11.5 22 ø32 ø32 25sq. Button color eplace the mark by the following button color code Color Green ed White Yellow Blue Orange Code G W Y O With wire-wrap pin terminals have a depth of 47mm. white illuminated pushbutton is fitted with a transparent color lens. The color lens is made of a tinted transparent material. amp voltage Voltages other than above are available Code D Incandescent B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC Neon 120V C 0V C /166 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbutton witches 165-2 Pushbutton switches Operator Contact Momentary action Type Flush round head 165-2F11 lternate action Type 165-2F511 Dimensions, mm 1 to 5 165-2F22 165-2F522 F87-211 165-2F33 165-2F533 11.5 ø20 ø25 Flush square head 165-2F11 165-2F511 1 to 5 165-2F22 165-2F522 20sq. F87-201 165-2F33 165-2F533 11.5 25sq. xtended round head 165-211 165-2511 1 to 5 165-222 165-2522 F87-210 165-233 165-2533 11.5 ø20 ø25 xtended square head 165-211 165-2511 1 to 5 165-222 165-2522 20sq. F87-200 165-233 165-2533 11.5 25sq. Concave square head 165-2C11 165-2C511 1 to 5 165-2C22 165-2C522 F87-199 165-2C33 165-2C533 11.5 20sq. 16.5 25sq. Mushroom head 165-2M11 1 to 5 165-2M22 ø32 F87-2 165-2M33 11.5 22 Mushroom head with square bezel 165-2YM11 1 to 5 165-2YM22 ø32 F87-214 165-2YM33 11.5 22 25sq. Note: eplace the mark by the following color code, see page /168. Fuji lectric F Components & ystems Co., td./d & C Catalog /167
Pushbutton witches 165-2 Pushbutton switches Operator Contact Type Dimensions, mm With selector ring 165-2222 1 to 5 90 ø25 F87-207 11.5 ø20 22 With selector ring with square bezel 165-2Y222 1 to 5 90 ø25 F87-206 11.5 ø20 22 25sq. Push-lock, turn-reset 165-2V11 1 to 5 165-2V22 ø32 F87-210 165-2V33 11.5 22 Push-lock, turn-reset with square bezel 165-2YV11 1 to 5 165-2YV22 ø32 F87-200 165-2YV33 11.5 22 25sq. Button color eplace the mark by the following button color code Color Code Green G ed Black B White W Blue Contact arrangement and operator position 165-2, 2Y ing eft ight Yellow Y Orange O The color lens is made of a tinted transparent material. (xcept for M, YM, V, YV, types) white pushbutton is fitted with a transparent color lens. black pushbutton consists of a transparent color lens and an attached black legend plate. (xcept for M, YM, V, YV, types) With wire-wrap pin terminals have a depth of 47mm. Terminal number and contact block position Type number display side Button Free U U Upper ➂➀ ➁➃ NC NO ower Depressed U: Upper contact block : ower contact block /168 Fuji lectric F Components & ystems Co., td./d & C Catalog
elector witches 165-2 elector switches/2-position (90-degree) Operator Operation Key removable position Knob Maintained Knob Key Key with square bezel F02-111 F02-112 F02-113 F02-114 pring return Maintained pring return Maintained pring return Maintained pring return B D B D Contact Type Dimensions, mm 165-2P2B11 165-2P2B22 165-2P2B33 165-2P0B11 165-2P0B22 165-2P0B33 165-2YP2B11 165-2YP2B22 165-2YP2B33 165-2YP0B11 165-2YP0B22 165-2YP0B33 165-2J211 165-2J222 165-2J233 165-2J2B11 165-2J2B22 165-2J2B33 165-2J2D11 165-2J2D22 165-2J2D33 165-2J011 165-2J022 165-2J033 165-2YJ211 165-2YJ222 165-2YJ233 165-2YJ2B11 165-2YJ2B22 165-2YJ2B33 165-2YJ2D11 165-2YJ2D22 165-2YJ2D33 165-2YJ011 165-2YJ022 165-2YJ033 1 to 5 1 to 5 1 to 5 11.5 13.5 1 to 5 11.5 13.5 11.5 11.5 37 37 25 25 25 25 ø25 25sq. ø25 25sq. The key can be removed only at the following positions: : B: D: For spring-return selector switches, the key can be removed at position. There are 6 available key types;, B, C, D, and F. tandard key code is. With wire-wrap pin terminals have a depth of 47mm. Terminal number and contact block position Type number display side ➂➀ ➁➃ NC NO Upper Middle ower Contact arrangement and operator positions: 2-position Contact arrangement Operator position eft ight U: Upper contact block M: Middle contact block : ower contact block M M U 3 4 1 U 2 3 4 U M U M Contact arrangement (terminal No.: common) : Middle : Upper, lower : Upper, middle, lower Fuji lectric F Components & ystems Co., td./d & C Catalog /169
elector witches 165-2 elector switches/2-position Operator ever ever color Black Operation Contact Type Dimensions, mm 1 to 5 Maintained 165-22B11 165-22B22 45 F87-209 165-22B33 11.5 ø25 ever with square bezel Black Maintained 165-22B11 1 to 5 165-22B22 45 F87-203 165-22B33 11.5 25sq. Contact arrangement and operator position 165-2, 2 ever Up Down Terminal number and contact block position Type number display side Contact block M M ➂➀ ➁➃ NC NO Upper Middle ower U U Contact arrangement (terminal No.: common) : Middle : Upper, lower : Upper, middle, lower U M U M U: Upper contact block M: Middle contact block : ower contact block With wire-wrap pin terminals have a depth of 47mm. /170 Fuji lectric F Components & ystems Co., td./d & C Catalog
elector witches 165-2 elector switches/3-position (45-degree) Operator Operation Key removable position Knob Mainteined Knob with square bezel Key Key with square bezel F87-208 F87-202 F87-223 F87-222 pring/ manual return pring/ manual return pring return Mainteined pring/ manual return pring/ manual return pring return Mainteined pring/ manual return pring/ manual return pring return Mainteined pring/ manual return pring/ manual return pring return D C D D C D Contact Type Dimensions, mm 165-2P3B22 165-2P3B33 165-2P6B22 165-2P6B33 165-2P7B22 165-2P7B33 165-2P1B22 165-2P1B33 165-2YP3B22 165-2YP3B33 165-2YP6B22 165-2YP6B33 165-2YP7B22 165-2YP7B33 165-2YP1B22 165-2YP1B33 165-2J322 165-2J333 165-2J322 165-2J333 165-2J3D22 165-2J3D33 165-2J3C22 165-2J3C33 165-2J622 165-2J633 165-2J6D22 165-2J6D33 165-2J722 165-2J733 165-2J722 165-2J733 165-2J122 165-2J133 165-2YJ322 165-2YJ333 165-2YJ322 165-2YJ333 165-2YJ3D22 165-2YJ3D33 165-2YJ3C22 165-2YJ3C33 165-2YJ622 165-2YJ633 165-2YJ6D22 165-2YJ6D33 165-2YJ722 165-2YJ733 165-2YJ722 165-2YJ733 165-2YJ122 165-2YJ133 1 to 5 1 to 5 1 to 5 11.5 13.5 1 to 5 11.5 13.5 11.5 11.5 37 37 25 25 25 25 ø25 25sq. ø25 25sq. The Key can be removed at the following positions: : B: C: D: : F: G: For spring-return selector switches, the key can be removed only at position. For manual/spring-return selector switches, the key can be removed at positions D, and F for type J6, and position, and G for type J7. There are 6 available key types;, B, C, D, and F. tandard key code is. With wire-wrap pin terminals have a depth of 47mm. Fuji lectric F Components & ystems Co., td./d & C Catalog Contact arrangement and operator positions: Contact arrangement Operator eft position 3 Center ight U 1 2 1 U 2 1 M 2 1 2 4 U: Upper contact block M: Middle contact block : ower contact block Contact block positions: ee page /170 /171
elector witches 165-2 Illuminated selector switches Operator Operation amp voltage No. of positions Contact Type Dimensions, mm Knob F90-607 Maintained Flat D V DC Incandescent V C/DC Neon 110V C Neon 220V C 2 3 2 3 2 3 2 3 1NO+2NC 165-2P2113 165-2P2223 165-2P3223 165-2P211 165-2P222 165-2P322 165-2P2111 165-2P2221 165-2P3221 165-2P211M1 165-2P222M1 165-2P322M1 22 ø20 ø25 Knob color (arrow) eplace the mark by the following color code Contact arrangement and operator positions: 2-position Color Code Green G ed Knob color (arrow) Black White W Blue Yellow Y Orange O Contact arrangement Operator eft position 1 M 2 1 U 2 ight M U amp voltage Voltages other than above are available Code D Incandescent B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC Neon 120V C 0V C 3-position Contact arrangement Operator eft position U Terminal number and contact block position Type number display side b (-) a (+) ➂➀ ➁➃ NC NO Upper Middle ower Contact arrangement (terminal No.: common) : Middle : Upper, lower Center ight U: Upper contact block M: Middle contact block : ower contact block U U /172 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pilot ights 165-2 Pilot lights ens amp Voltage Type Dimensions, mm Flush round Flat D V DC 165-2Z3 1 to 5 Incandescent V C/DC 165-2Z a (+) Neon 110V C 165-2Z1 b (-) F87-213 220V C 165-2ZM1 11.5 ø20 ø25 Flush square Flat D V DC 165-2Z3 1 to 5 Incandescent Neon V C/DC 110V C 165-2Z 165-2Z1 a (+) b (-) 20sq. xtended round F87-205 Flat D 220V C V DC 165-2ZM1 165-2Z3 11.5 1 to 5 25sq. Incandescent V C/DC 165-2Z a (+) Neon 110V C 165-2Z1 b (-) F87-212 220V C 165-2ZM1 11.5 ø20 ø25 xtended square Flat D V DC 165-2Z3 1 to 5 Incandescent Neon V C/DC 110V C 165-2Z 165-2Z1 a (+) b (-) 20sq. F87-2 220V C 165-2ZM1 11.5 25sq. ens color eplace the mark by the following lens color code Color Code Green G ed White W Yellow Y Blue Orange O amp voltage Voltage other than above is available Code D Incandescent Neon B K P 5V DC 6V DC 12V DC 5V C/DC 12V C/DC 120V C 0V C The color lens is made of a tinted transparent material. white lens is fitted with a transparent color lens. With wire-wrap pin terminals have a depth of 29mm. Fuji lectric F Components & ystems Co., td./d & C Catalog /173
Pushbuttons/electors/Pilot ights 165-2 Mounting space Mounting space, mm Illuminated pushbuttons, pushbuttons, selector switches, illuminated selector switches and pilot lights ound head quare head Mushroom head Push-lock, turn-reset 25 25 33 Panel Panel cutting cutting Panel 25 25 25 25 cutting ø16.2+0.2 0 ø16.2+0.2 0 ø16.2+0.2 0 33 Terminal number Type Wiring Terminal position Illuminated pushbuttons, Illuminated selector switches a (+) 1 3 b (-) 2 4 Type number display side 3 1 3 1 b (-) 2 4 2 4 Pushbuttons elector swiches 1 3 2 4 3 1 a (+) 2 4 Pilot lights (without transformer) a (+) b (-) Type number display side a b /174 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 Notes on use Notes on use Installation on panel For installation, use dedicated wrench X601. The appropriate tightening torque is 0.6 to 1N cm. The installation sequence is as follows: Pass the operator base through the hole in the panel and secure it by tightening the bezel. Properly position the catch arms of the contact holder and the catch legs of the operator base and push the contact holder onto the operator base. To remove the contact holder, pull it while pressing the catch arms inward. Panel Contact holder Mounting steps of switch with transformer ➀Pass the switch operator through the panel hole and secure with a nut by way of the retainer metal from the front of the panel. ➁lign the position of the catch arm of the contact block holder with that of the catch leg of the switch operator. ngage these two catches by pushing them together. ➂Insert and secure the transformer unit while assembling the contact block holder with the retainer metal. ➃Connect the receptacle terminal with lead wires extending from the transformer to the lamp terminal of the contact block holder. (Be care on the polarity of the D. ed: +, Black: ) ➄Push in and secure the standard accessory Panel etainer metal Contact block holder Catch leg Transformer amp terminal Operator base Catch leg Mounting hole Catch arm Operator Catch leg Mounting hole insulation cover by aligning its position with each terminal. To replace the transformer, remove the transformer by widening the catch leg of the contact block holder. Pay attention not to excessively widen the catch leg. Mounting steps are the same as the above steps ➂, ➃, and ➄. Catch arm eceptacle terminal Insulation cover Operating voltage and rated voltage of incandescent lamps ated voltage 6V 14V 28V (tandard) Operating voltage 4 to 5V 10 to 12V 20 to V Incandescent lamps should be operated at the operating voltages if a lamp service life of 5,000 to 10,000 hours are needed. The ambient temperature must not exceed 30 C if the lamp is used at the rated voltage continuously. Method of replacing lamp Incandescent lamps/d lamps/neon lamps emove the color lens and inner button with a remover X6. Then draw out the lamp with a lamp changer X672. When installing lamps, do it manually and in the reverse order of removing. Products with blue and green Ds The D devices on products with high-brightness (blue and green) Ds are very sensitive to static electricity. When replacing D lamps do not allow static electricity to come into direct contact with the metal frame on the upper side of the D lamp. The D device may be damaged if this part is subjected to static electricity. When installing or removing an D lamp, it is recommended that you use the lamp changer (X672). Metal frame D To replace the lamp of a 165-2 illuminated pushbutton switch (M,V), remove the button and draw out the oil-tight cap. emover (X6) ecess of the oil-tight cap Then, replace the lamp using a lamp changer (X672) and push the oil-tight cap into its original position with its engaging projection properly adjusted (see the figure below). Installing the protection cover / dust-tight cover, guardring Be careful that the panel thickness does not exceed the following: Protection cover: 2.6mm max. Dust-tight cover: 2.0mm max. Guard ring: 2.5mm max. V M Note: amp of 165-ZM type can not be replaced. ngaging projection of oil-tight cap ngaging recess at the inner end of the switch Fuji lectric F Components & ystems Co., td./d & C Catalog /175
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 Notes on use Method of replacing color lens To remove the color lens, insert a small screwdriver into the color lens and twist in direction of the arrow. Color lens egend plate creen Color lens ecess For an 165-2, use a small standard screwdriver or a similar tool with a flat end. If one side of the color lens is removed from the screen, insert the screwdriver or a similar tool deeper and remove the color lens together with the screen. creen Color lens Projection eplacing pushbuttons In the case of alternative action type pushbutton switches and illuminated pushbutton switches, be sure not to replace the pushbuttons in their locked state. This could result in internal damage to the mechanism. Description sheet The Fuji description sheet is 25µm thick. If preparing custom description sheets, make sure that the thickness is 0.1mm or less. Contact block To replace a contact block, use removing tool GX012. If excessive force is applied when attempting to open the support legs for the contact block holder, deformation or damage may occur. andling precautions Do not apply torque in excess of 1.0 N m to operate the selectors switch (Type P ). equired operating force of switches is less than 0.1 N m. Do not tap on a pushbutton to turn it ON or OFF, such handling may damage it. Be sure to operate the pushbutton by hand. Key type selector switch Five key types (Type B to Type F) are available besides Type, which is the standard key type. Be sure to use a key with a symbol which is matched with the symbol on the main unit. ymbol on the key ymbol on the main unit Fully insert the key into the main unit before turning the key. The key turning force should not exceed 0.1 N m. Do not pull out or insert the key forcibly. Wiring connections Use a soldering iron with a wattage of not more than 30W and a tip length of more than 20mm. Use a rosin-core solder With a 30W iron complete soldering within 5 seconds, or 10 seconds with a 20W iron. Do not apply external force to the terminals. Do not deform the terminals. Because lead-free solder's melting point is slightly high, soldering work may be difficult. Use a soldering iron whose tip is rather large or whose calorie is rather high. Wires that can be connected Two solid wires with a maximum diameter of 0.8mm (solder) One stranded wire with a maximum area of 0.75mm 2 (solder) Flat connection terminal (2.8-1.25-5) 0.5 to 1.25mm 2 (2.8-0.5-5) 0.2 to 0.5mm 2 Using contact blocks When using NO and NC contacts in the same contact block, avoid connection that involves opposite polarity or wiring from different types of power supply. For wiring to adjacent terminals, use insulated tubing to prevent short-circuit and to assure isolation. For solder terminals, be careful when connecting thick wires. Do not use too much solder. Wiring to wire-wrap pin terminals elect the appropriate wire sizes and tools from the table below. Wire size Bit leeve Number of effective wraps 0.4mm dia. 3-1-B bout 8 0.5mm dia. 1-1-B bout 6 (0.65mm dia.) (2-) (2-B) (bout 6) Use ordinary wrapping for connection. Wires of 0.65mm dia. must not be used on adjacent terminals. owever, 0.65mm dia. wire can be mixed with 0.4 and 0.5mm dia. wires. Wiring to tab terminals Use receptacles, No. 110. Installing lamps in close order When continuously lighting pilot lights or pressing illuminated pushbuttons installed in close order, care must be taken that the ambient temperature does not exceed the rated value. /176 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 Notes on use Ds D amp Malfunctioning The D lamp is lit by a very small level of current (approximately 0.01m). Therefore, the it may be erroneously lit by a current leaking from the surge absorption circuit or semiconductor circuit or due to stray capacitance between cables. In that case, provide a countermeasure (e.g., connect a resistor in parallel with the D lamp). Countermeasure for Malfunctioning hunt esistor or C elements connected in parallel amp malfunctions can be prevented by connecting a shunt resistor () or C elements (a capacitor and resistor) in parallel with the D lamp terminal. The resistance and C values vary depending on the model and the operating conditions. xample 1 xample 2 amp Transformer C: Capacitor C : esistor hunt X1 resistor X2 X1 X2 V DC : 10kΩ (1W) 110V C C: 0.33µF (250V C) : 120Ω (0.25W) 220V C C: 0.33µF (250V C) : 120Ω (0.25W) Incoming surge Be careful that since high luminance D products use an element sensitive to static electricity, they may not be lit by an abnormal voltage like surge. torage and operation site Use the unit within the rated operating ambient temperature and humidity ranges. Do not use the enclosed type in places where oil or water is sprayed or where dust accumulates. In places such as these, use the oil-tight type or provide a dust cover. The oil-tight type is evaluated with standard cutting oil and cooling oil applied. The oil-tight type cannot be used with some special oils. Buzzer Noise If the application circuit is likely to generate excessively strong noise, connect a surge absorber (e.,g., FUJI' NC390D, provided that the switch is a V type) in parallel with the buzzer. Place of Use The buzzer does not have a drip-proof construction. Do not use the buzzer in places where oil or water is sprayed or where dust accumulates. If the buzzer is a splash-proof type, it will resist sprays of water. Do not use the buzzer in places that are subject to an excessive amount of corronsive gas. Be careful that the buzzer is likely to sound erroneously due to leakage current or the like. Using a flat D in 48V DC circuit When a flat D lamps having a rated voltage of V DC is used with 48V DC circuit, connect an external resistor of 1,800Ω (2W). Preventing the neon lamp from incorrectly turning ON The neon lamp may incorrectly turn ON due to current leakage or voltage induction. In such a case, connect a shunt resistor in parallel with the lamp. xample) 110V C: 100k (0.25W) 220V C: 50k (2W) If an external surge of 3kV or more may occur, connect a surge absorption element in parallel with the lamp. Numerical indicators To ensure high reliability and long life for the D, design the circuit not to exceed the maximum ratings under any operating conditions. Keep in mind that the display may malfunction or be damaged due to noise in input signals. (TC type) Wire the TC type as shown on the nameplate. The IC may break if the supply voltage is connected in reverse. Keep in mind that the correct display will not appear with negative logic input because the TC type accepts positive logic input. Operation Do not use a hitting or bouncing action to operate the button, or the switch may break. lways operate the switch by hand. Fuji lectric F Components & ystems Co., td./d & C Catalog /177
Pushbuttons/electors/Pilot ights/buzzers 164 and 165 ccessories ccessories for 164 and 165 Description Type Description Type Color chips (ound) Color Type /178, 5, Green X631-G 5, Z ed X631- White (For Neon) X631-W Blue X631- Yellow X631-Y Orange X631-O Clear X631-C F-682 For D, Neon Green X653-G Color chips (quare) Color Type, 5, G, Green X632-G G5, F, F5, ed X632- GF, GF5, Z White (For Neon) X632-W Blue X632- Yellow X632-Y Orange X632-O Clear X632-C F-681 For D, Neon Green X653-G Color chips (ectangular) Color Type T, T5, TG Green X633-G TG5, TF, TF5 ed X633- TGF, TGF5, ZT White (For Neon) X633-W Blue X633- Yellow X633-Y Orange X633-O Clear X633-C F-680 For D, Neon Green X653-TG Mushroom head button Color Type M, M5 Green X682-G ed X682- White X682-W Blue X682- Yellow X682-Y Orange X682-O I-40 Black X682-B Convex square head button Color Type M, M5 Green X683-G ed X683- White X683-W Blue X683- Yellow X683-Y Orange X683-O I-43 Black X683-B Convex rectangular head Color Type button TM, TM5 Green X684-G ed X684- White X684-W Blue X684- Yellow X684-Y Orange X684-O I-44 Black X684-B egend sheet -165 ound Type: X6- egend: ON, OFF, UP, DOWN quare Type: X616- egend: ON, OFF, UP, DOWN TT, TOP, OPN CO, UTO, MN, T, POW, V, FWD, IG, OW ectangular Type: X617- egend: ON, OFF, UP, DOWN TT, TOP, UTO, MN, FOWD, V When ordering, specify desired legend in the at the end of ordering code, Transparent blank sheets are also available. Use black oil ink. egend plate Type Color Dimensions, mm (crylic resin) ound X665 White ø12.2 x 0.9 X665-C Transparent X665-B Black -164 quare X666 White 12.2sq. x 0.9 X666-C Transparent X666-B Black ectangular X667 White 12.2 x.2 x 0.9 X667-C Transparent X667-B Black egend plate for spot D Type Dimensions, mm (crylic resin) ound X650 ø12.2 x 0.9 quare X651 12.2sq. x 0.9 ectangular X652 12.2 x.2 x 0.9 P-113 egend plate for selector switch (2-position) -226 Type: X664 egend: ON-OFF egend: Blank Dimensions, mm: sq. x 0.5 egend plate for symbol mark Mark Type quare ectangular quare I ectangular X666- X667- X666- X667- quare T X666-T F87-74 ectangular X667-T Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164 and 165 ccessories Description Protection cover Type For round and square head button Type: X671 For rectangular head button Type: X669 X826 This cover protect against accidental operation. Note: Not used for illuminated pushbuttons with guard. pplicable panel thickness is 2.6mm max. Dimensions, mm 33.2 M-378 31.5 X671 ø16.2 X669 ø16.2 23.5 10.5 14 X826 23.5 13.7 33.2 Dust-tight cover F91-123, I-41 For round and square head button Type: X822 Dimensions, mm: sq. x 14.2 For rectangular head button Type: X668 Dimensions, mm: x 30 x 14.2 For mushroom head button Type: X649 Dimensions, mm: ø30 x These covers protect against dust. Note: pplicable panel thickness is 2.0mm max. Guard ring Type Color Dimensions, mm X676-B Black ø21 x 12 X676-GY Gray I-42 This guard ring is used in combination with an extended round head pushbutton ( or ). Note: pplicable panel thickness is 2.5mm max. Please place an order for a packing (X685) separately when you intend to use for 165 series. Transformer Voltage Type amp 100 to 110V C X805- D 200 to 220V C X805-M F90-949 100 to 110V C X806- Incandescent 200 to 220V C X806-M Fuji lectric F Components & ystems Co., td./d & C Catalog /179
Pushbuttons/electors/Pilot ights/buzzers 165-2 ccessories ccessories for 165-2 Description Type Description Type Color lens (ound) F87-631 Color lens (quare) For flush head (Used with 2F, 2F5, 2F, 2F5, 2Z) Color Type Green X26-G ed X26- Yellow X26-Y Blue X26- Orange X26-O Clear X26-C For extended head (Used with 2, 25, 2, 25, 2Z) Color Type Green X2605-G ed X2605- Yellow X2605-Y Blue X2605- Orange X2605-O Clear X2605-C For flush head (Used with 2F, 2F5, 2F, 2F5, 2Z) Color Type Green X2606-G ed X2606- Yellow X2606-Y Blue X2606- Orange X2606-O Clear X2606-C egend plate F87-631 F87-630 For flush head Color Type Used with White X2609-W Incandescent lamp, D lamp, Pushbutton * 1 Clear X2609-C Neon lamp * 2 Black X2609-B Pushbutton * 3 Dimensions, mm: ø * 4 x 0.9 For extended head Color Type Used with White X2610-W Incandescent lamp, D lamp, Pushbutton * 1 Clear X2610-C Neon lamp * 2 Black X2610-B Pushbutton * 3 Dimensions, mm: ø * 4 x 4.4 For flush square Color Type Used with White X2611-W Incandescent lamp, D lamp, Pushbutton * 1 Clear X2611-C Neon lamp * 2 Black X2611-B Pushbutton * 3 Dimensions, mm: 17sq. x 0.9 For extended square, concave square Color Type Used with White X2612-W Incandescent lamp, D lamp, Pushbutton * 1 Clear X2612-C Neon lamp * 2 Black X2612-B Pushbutton * 3 Dimensions, mm: 17sq. x 4.4 * 1 Illuminated pushbutton switches and pilot lights with incandescent lamps or D lamps, Pushbutton switches (excluding). * 2 Illuminated pushbutton switches and pilot lights with neon lamps. * 3 Pushbutton switches (black) * 4 ngraved range: 17mm dia. For extended head (Used with 2, 25, 2, 25, 2Z) Mushroom head button For illuminated pushbuttons (Used with 2M, 2YM) Color Green ed Yellow Blue Orange Clear Type X2607-G X2607- X2607-Y X2607- X2607-O X2607-C Color Green ed White Yellow Blue Orange Type X2614-G X2614- X2614-W X2614-Y X2614- X2614-O For concave head (Used with 2C, 2C5, 2C, 2C5) For non-illuminated pushbuttons (Used with 2M, 2YM) F87-632 Color Green ed Yellow Blue Orange Clear Type X2608-G X2608- X2608-Y X2608- X2608-O X2608-C F87-633 Color Green ed White Yellow Blue Orange Black Type X2613-G X2613- X2613-W X2613-Y X2613- X2613-O X2613-B /0 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 165-2 ccessories Description Push-lock, turn-reset button Type For illuminated pushbuttons (Used with 2V, 2YV) Color Type Green X2616-G ed X2616- White X2616-W Yellow X2616-Y F87-634 Dust-tight cover For pushbuttons (Used with 2V, 2YV) Color Type Green X26-G ed X26- Yellow X26-Y Black X26-B For flush round (Used with 2F, 2F, 2F5, 2F5) Type: X2603-2 F87-636 Key washer For flush square (Used with 2F, 2F, 2F5, 2F5) Type: X2603-2 These covers protect against dust. Type: X2601 Mounting hole, mm 1.7 +0.2 0 rmax.0.8 17.9 +0.2 0 F87-635 ø16.2 +0.2 0 Fuji lectric F Components & ystems Co., td./d & C Catalog /1
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 ccessories ccessories for 164, 165 and 165-2 Description Type Description Type Incandescent lamp Voltage Type Wrench Type: X601 D-9 6V, 0.6W X641 14V, 0.7W X642 28V, 0.7W X643-741 When installing a command switch on a panel, this tool is useful for tightening the switch firmly and efficiently. D lamp Voltage Type Terminal cover Type: X2602 F02-116 5V DC 6V DC 12V DC V DC X695-5 X695-6 X695-12 X695- eplace the mark by the luminous color code ed (), Green (G), Orange (O), mber (), Yellow (Y), Blue () Neon lamp Voltage Type uminous color 110V C X655- Green X654- Orange 120V C X655-K Green X654-K Orange 220V C X655-M Green X654-M Orange 0V C X655-P Green P-119 X654-P Orange F87-637 Contact block Terminal Type K-1140 Dummy unit K-1141 This cover is used with 164 and 165 and 165-2 (except pilot lights). Pass the wires through the cover, then mount the cover in position. older/tab Wire-wrap Type: GX002 GX001 GX001W dummy unit is used to fill the space where no contact blocks are installed. For example, two dummy units are used if contact block is installed, and one dummy unit is used if contact blocks are installed. Panel plug Color Type emover Type: GX012 ound Black X622-B IP40 Gray X622-GY IP40 quare Black X644-B IP40 Gray X644-GY IP40 M-334 This tool is used for replacing the contact blocks or dummy units. ectangular Black X645-B IP40 Gray X645-GY IP40 Black X850-B IP65 I-6 amp changer Type: X672 If the switch is fitted with a lamp, use this tool to remove the lamp. The tool is unnecessary when installing a lamp. F02-117 emover Type: X6 This tool is used for replacing the color chips or screens. -34 Contact holder remover P-522 Type: X699 This tool is used to remove a contact holder when switches are densely installed. /2 Fuji lectric F Components & ystems Co., td./d & C Catalog
Pushbuttons/electors/Pilot ights/buzzers 164, 165 and 165-2 ccessories Description Type ockets Terminal Type Used with M-1097 older/tab X697- Pushbuttons Wire-wrap X697-W PC board X697-P older/tab X697- Illuminated Wire-wrap X697-W pushbuttons PC board X697-P Contact arrangement is only. xcept for 165-2P types ockets for Terminal Type D older/tab X697-3 Wire-wrap X697-W3 M-1098 Contact arrangement is only. These sockets are used only when D lamps rated for V DC are used under 110V C/DC. xcept for 164, 165 and 165-2 series pilot lights or 165-2P type. When side-by-side mounting and continuous lighting, note that a socket has higher temperature over the ambient temperature. Dimensions, mm older/tab X697 JPN 75 17.9 8.8 27.8 PC board mounting Pushbuttons 12 8-ø1.3 6.3 14.3 Wire-wrap PC board Illuminated pushbuttons 12 0.6 10-ø1.3.5 19.8 JPN X697 JPN 3.5 4.8 10.3 6.3 14.3 X697 1 0.5 witch X697 JPN PU ocket 50.6 For wiring to wire-wrap pin terminals, select appropriate wire sizes and tool from the table below. Wire size Bit leeve Number of effective wraps 0.4mm dia. 3-1-B bout 8 0.5mm dia. 1-1-B bout 6 (0.65mm dia.) (2-) (2-B) (bout 6) Use ordinary wrapping for connection. Wires of 0.65mm dia. must not be used on adjacent terminals. owever, 0.65mm dia. wire can be mixed with 0.4mm and 0.5mm dia. wires. Fuji lectric F Components & ystems Co., td./d & C Catalog /3