Bag Filter. Latch mechanism. has been provided additionally. (Mechanism for protecting the cover from being removed)

Bag Filter Series FGF Bracket for V-band Latch mechanism has been provided additionally. (Mechanism for protecting the cover from being removed) PT. Reinforced V-band with tightening position mechanism PT. FGF, FGF type (three elements, five elements included) Optimum for the large flow filtration The bag-stated element (made of non-woven cloth) makes it possible to filtrate the large flow with lower pressure drop. Easy to dispose of the collected foreign matters. ollecting the foreign matters inside an element realizes the easy disposal. The case inside and surroundings are not soiled. Easy maintenance Easy to remove and install the element and basket, and easy to exchange elements. Select from a wide range of filtration accuracy Nominal filtration accuracy to 00 μm Major operating fluids oolant (Oil-based, queous) Weak alkali-based cleaning fluid utting fluid Industrial water ontact us for other kinds of fluids. Variations Series FGF FGF FGF FGF type (one element included) NBR FKM Options Body Gasket, O-ring Stainless steel 04 Stainless steel 04 SS400 Description Davit for element ompanion flange Foundation bolt ( pcs) Number of elements Features (easy replacement of elements) P.780 system P.78 How to Order, Specifications P.782 Model selection and Flow characteristics P.78 onstruction, omponent parts, Seal list P.784 Dimensions P.78 Options P.786 P.788 Specific Product Precautions P.79 pplicable models (number of elements) FGF (one element) ø90 x l440 ø90 x l770 Table of ontents FGF (three elements) Rc2 4 B JIS0 K FF 6 B JIS0 K FF FGF (five elements) Max. flow (water, at ΔP = 7 kpa) pprox. 400 l/min pprox. 200 l/min pprox. 2000 l/min 779

Feature (Effortless replacement of elements) (one element including type) How to remove an element. fter stopping the operation, close the valve in the order of inlet and outlet. 2. Open the air release valve to let the internal pressure of a filter be zero, and open the drain valve and liquid discharging valve to let out the internal fluid completely.. fter pulling the pin for confirming the tightening position, loosen the tightening nut, and then remove the T-bracket from the latch. (It is convenient to use a wrench commercially available with the nominal size 7.) How to attach an element. Pull a new element by the cloth handle toward the center, and put it inside the basket, folding the edge of an element. Further, push the edge of an element to the bottom plate's flange surface of the basket thoroughly. 2. Grasp the handle and put the basket in the case. - -2 2 - -2 - Note) Set the handle avoiding attaching it to the notch (guide groove) of the case. 4. Remove the cover upward by turning it counterclockwise. 4-4-2. Set the O-ring to the case. Replace the O-ring with a new one if it is expanded. (Refer to page 784, Seal list, Part nos.) 4. djust the pins (two locations) to the guide slit of the case inside the cover, and push them thoroughly and turning clockwise. 4-4-2. Using the handle, remove the basket vertically. Inspect a gasket in the case, and replace it with a new one if it is expanded. (Refer to page 784, Seal list, Part nos.) 6. handle made of cloth is attached to the element so that elements can be pulled out of the basket by fingers or using sticks, pulling them to the center. 6-6-2. Install the V-band in the edge of the cover and case correctly. 6. Gently strike the circumference around the V-band with a plastic hammer, etc. to fit the connection. 7. Install the T-bracket correctly in the latch. fter fastening the tightening nut to the prescribed position, insert the pin for confirming the tightening position. Refer to the back of page 796, Specific Product Precautions 4. 7 Note) Please use caution for burns in the case of a high temperature. aution When restarting this product or performing the air release works after replacing the elements, refer to the back of page 796, Specific Product Precautions 4. 780

Variations of Bag Filters Bag Filter Series FGF vailable combination between an element and a vessel FGF Vessel with one element 0. MPa type Standard products FGF Vessel with three elements 0. MPa type Vessel FGF Vessel with five elements 0. MPa type High pressure spec. Vessel with one element.0 MPa type (P.792) Element Standard elements P.782 Sub-element + Standard element P.788 Sub-element HEPO element P.789 Long service life element Branch type element + One-touch type V-band P.790 PP (Polypropylene) bag element Filter paper element P.79 Note) ombinations between standard or made-to-order elements and standard or made-to-order vessels are marked ( ) as above. Types of Element Standard element Made-to-order elements Bag element Sub-element HEPO element (For precision Long service life element Branch type element PP (Polypropylene) bag element Filter paper element Note) Refer to page 788 through to 792 for details on made-to-order elements and vessels. 78

Bag Filter Series FGF Three, five elements included Vessel material S L R One element included Stainless steel 04 SS400 Stainless steel 04 SS400 No. of elements pcs included (FGF) pcs included (FGF) pcs included (FGF) Gasket, pplicable model O-ring FGF FGF FGF NBR FKM Part number of element for replacement Specifications EJ Element symbol Model Operating pressure Operating temperature ommon Maximum flow rate Note ) Vessel Element pplicable fluid Internal volume Mass valve Handle for picking elements Davit for elements Nominal filtration accuracy Basket withstand differential pressure strength Size ccessory B 0S 60S ø90 x l440 ø90 x l770 0S 00 ø90 x l440 ø90 x l770 How to Order FGF S 20 E 00 D FGF S 40 E 00 D Element material (Polyester) 20 40 60 Rc2 4 B JIS0 k FF 6 B JIS0 k FF Option Nil D F L pplicable model FGF FGF FGF Option FGF None Davit for element ompanion flange Foundation bolt ( pcs) pplicable model FGF FGF FGF FGF FGF In the case of multiple options, indicate symbols in an alphabetical order. Made to Order Note ) Nominal filtration accuracy Nominal filtration accuracy (μm) Filtration efficiency Note 2) 00 00 02 00 00 0 2 0 00 9 wt % eliminated 87 wt % eliminated 80 wt % eliminated 74 wt % eliminated 6 wt % eliminated Note) Nominal filtration accuracy is the name given for the filtration accuracy calculated as a percentage of a load, and will differ from the actual filtration accuracy that is achieved from a fluid flow. Note 2) Test condition Operating fluid: Water Dust in use: TD Pressure drop: ΔP = at 0.0 MPa SE standards in the United States of merica J726 Dust for test use for air cleaner for automobiles Made to order specifications. (For details, refer to page 788 to 792). FGF-20 FGFB-20 FGF-40 FGFB-40 FGF-60 FGFB-60 Note 2) MX. 0. MPa MX. 80 pprox. 400 l/min pprox. 200 l/min pprox. 2000 l/min Stainless steel 04 Rc2 9 l 9 kg Basket integrated None l 2 kg Part No.: G46-0-02M /4 B ball valve Part No.: K-S Yes Polyester, 0, 2, 0, 00 μm 0. MPa element included elements included elements included ø90 x l440 ø90 x l770 ø90 x l440 ø90 x l770 ø90 x l440 ø90 x l770 Note ) onditions: Fluid water, Pressure drop 7 kpa, Nominal filtration accuracy 00 μm Note 2) Refer to page 792, for the maximum operating pressure of.0 MPa type. 782 queous coolant, Weak alkali cleaning fluid, Industrial water (vessel material: Stainless steel 04) Oil-based coolant, utting oil (vessel material: SS400) 04 l 70 kg Stainless steel 04, SS400 4 B JIS0 K FF 6 B JIS0 K FF 6 l 90 kg 24 l 270 kg 07 l kg

Bag Filter Series FGF Model Selection and Flow haracteristics. Determine the material for the vessel, gasket and O-ring after confirming operating fluids. 2. Select a vessel model by referring to the maximum flow rate in the specifications, (page 782) after confirming the operating flow rate.. onfirm whether the operating pressure and temperature is within the specification range (page 782) or not. 4. alculate the nominal filtration accuracy of an element that is required.. onfirm the flow rate and pressure drop based on the below flow characteristics when selecting a vessel and an element. 6. Determine a model by the element size, (ø90 x l770) when many contaminants (pollutants) are contained in the fluid. 7. Select the required option. 8. Determine the filter model according to the model selection procedures above. (Refer to page 782.) Flow haracteristics Flow rate per element Graph : Flow haracteristics of Series FGF Fluid: Water, Temperature: Room temp. The flow rate per element can be obtained as follows using Graph and Table B. Note ) The flow characteristics does not change according to the element size. The life expectancy changes in proportion to the filtration area. Note 2) We recommend that the pressure drop be calculated by 7 kpa. Much pressure drop in the initial stage will substantially shorten the service life in an element in the case of a highly turbid fluid. <alculation methods> (Example) Viscosity 00 m 2 /sec Pressure drop 7 kpa Nominal filtration accuracy 00 μm ) ccording to Graph, Flow haracteristics, the flow rate, 400 l/min is obtained from the point of intersection of the 00 μm line and the y-axis. 2) Next, according to Table B, Viscosity onversion Table, the flow coefficient is obtained as 8% for 00 m 2 /sec. ) The flow rate 400 l/min multiplied by the flow coefficient 8%, that is 280 l/min, gives the flow rate per element. 400 l/min (flow rate) x 8% (flow coefficient) = 40 l/min Pressure drop (kpa) 00 μm, 0 μm 2 μm 0 0 μm, 00 μm 7 q 0. 0 00 400 000 0000 Flow rate (l/min) Table B: Viscosity onversion Table Viscosity (mm 2 /sec) 0,000 8,000 6,000 4,000 2,000,00,000 800 600 400 200 00 Flow coefficient (%) 2. 2.6. 8 6 7 2 8 8 00 Multiply the number of elements by the flow rate per one element in case that the flow rate of including or elements is calculated. 78

4 2 4 2 4 2 4 2 Series FGF onstruction FGF FGF-40 FGF-60 valve Handle Bracket for V-band Pin Guide slit valve Davit for cover enter bolt Nut Spring washer Retainer Drain port Pressure gauge Drain discharge Drain discharge omponent Parts and Seal List No. Description Part No. Qty. pplicable model Note) 2 over Filter case Stainless steel 04 Stainless steel 04 Basket BT-7S# FGF-20 Stainless steel 04 BT-8S# FGFB-20 4 Element V-band Refer to page 782, How to Order. Y-9S Polyester Stainless steel 04 6 7 O-ring Gasket L-2S NBR FGFS-20 L-22S FKM FGFL-20 L-20S NBR FGFS-20 L-2S FKM FGFL-20 Note ) Refer to "How to Order" on page 782 for the part of the part number. 784 omponent Parts and Seal List No. Description Part No. Qty. pplicable model Note) 2 4 6 7 8 9 0 2 over Filter case Stainless steel 04 Stainless steel 04 BT-S Stainless steel 04 Basket BT-4S Stainless steel 04 Element Hinge bolt Eyenut Washer Parallel pin Lifter Handle Refer to page 782, How to Order. Polyester SF440 SF440 SS400 S4 SS400 SS400 L-26S NBR L-27S O-ring L-2S FKM L-24S L-20S NBR Gasket L-2S FKM Note ) Refer to "How to Order" on page 782 for the part of the part number. FGF-40 FGF-60 FGFB-40 FGFB-60 FGF-40 FGF-60 FGFS-40 FGF-40 FGFS-60 FGF-60 FGFL-40 FGFR-40 FGFL-60 FGFR-60 FGFS-40 FGF-40 FGFS-60 FGF-60 FGFL-40 FGFR-40 FGFL-60 FGFR-60

HOOK OPEN Bag Filter Series FGF Dimensions FGF-20 Fluid release B..D 96 x ø20 M6 for foundation bolt FGF-40 x ø24 M20 for foundation bolt 0 Drain port 68 B..D 422 Drain port Fluid release Davit 70 Rc/4 7 pprox. E (When the valve is opened.) D B Model B FGFS-20 FGFL-20 669 72 FGFSB-20 FGFLB-20 999 0 FGF-60 6 77 Rc2 Davit 0 820 0 (2) D V V 94 27 Rc2 Drain discharge (mm) E 040 70 in the inlet side O.D. 24 Rp/4 Drain port in the outlet side Rc2 x ø24 M20 for foundation bolt Fluid release E (When the cover is lifted.) D Rc/4 4 B JIS0 K FF B 80 20 Model B FGFS-40 FGF-40 FGFL-40 FGFR-40 866 90 FGFSB-40 FGFB-40 FGFLB-40 96 280 FGFRB-40 O.D 48 Fluid release 289 40 470 D 464 794 Drain port 2 B JIS0 K FF E 80 90 Davit for cover in the inlet side in the outlet side 2 B JIS0 K FF (mm) 4 B JIS0 K FF B..D 70 0 Drain port 90 47 Rc/4 6 B JIS0 K FF Davit for cover in the inlet side E (When the cover is lifted.) D B 6 20 O.D 608 2 B JIS0 K FF Fluid release 70 in the outlet side Drain port 2 B JIS0 K FF 6 B JIS0 K FF Model B FGFS-60 FGF-60 FGFL-60 FGFR-60 96 00 FGFSB-60 FGFB-60 FGFLB-60 286 80 FGFRB-60 20 60 D 649 979 (mm) E 790 220 78

Options Davit for hanging an element BO-6S Model pplicable model B (mm) BO-4S, S Model pplicable model B (mm) FGFS-20 FGFS-40 BO-6S FGFL-20 FGFSB-20 FGFLB-20 2400 400 90 (Height from the foundation) 4 BO-4S FGF-40 FGFL-40 FGFR-40 FGFSB-40 FGFB-40 FGFLB-40 FGFRB-40 2400 0 446 270 660 446 (mm) B B (Height from the foundation) Model pplicable model FGFS-60 FGF-60 FGFL-60 FGFR-60 BO-S FGFSB-60 FGFB-60 FGFLB-60 FGFRB-60 20 B 460 67 2860 790 67 ompanion flange Flange Gasket Hexagon bolt and nut T T2 8 x ø D I H G ø P..D B øe øf Part No. pplicable model G H I I-7S I-8S FGF-40 FGF-60 SS400 (Zinc chromated) 60 70 8 46 M6 x 2 M20 x 2. Note) 6 pieces are required per filter unit. (mm) Set of omponents for a ompanion Flange Part No. pplicable model Flange standards B F-86S F-87S F-88S F-89S FGF-40 SS400 FGFR-40 4 B JIS0 K 20 7.4 FGFS-40 PL, FF SUSF04 FGFL-40 FGF-60 SS400 FGFR-60 6 B JIS0 K 280 240 66.6 FGFS-60 PL, FF SUSF04 FGFL-60 Note) 2 pieces are required per filter unit. D 9 2 T 8 22 Part No. pplicable model E L-79S L-80S FGF-40 FGF-60 V # 600 9 220 67 Note) 2 pieces are required per filter unit. F T2 Part No. F-90S F-9S F-92S F-9S pplicable model FGF-40 FGFR-40 FGFS-40 FGFL-40 FGF-60 FGFR-60 FGFS-60 FGFL-60 Flange F-86S F-87S F-88S F-89S Gasket L-79S L-80S Hexagon bolt I-7S I-8S 786

Bag Filter Series FGF Options Foundation bolt L R d Hexagon nut d L S Part no. pplicable model I-2S I-S FGF-20 FGF-40 FGF-60 Nominal size of thread d M6 M20 (mm) Note) foundation bolts are required per filter unit. If ordering only foundation bolts, order bolts using the above part no. d 6 20 S 40 0 L (pprox.) 7 90 R (pprox.). 40 K (pprox.) 2 2. L 400 00 787

Specifications Please consult with SM for detailed size, specifications and delivery. Made to Order Sub-element and Standard element equipped Sub-element Standard element Effective for extending the service life in a standard element. Enclosed in the standard element to eliminate large foreign matter. Specifications ø90 x l440 ø90 x l770 Flow rate (l/min) Weak alkali queous coolant cleaning fluid to 0 0 to 00 2 to 00 0 to 200 Normal filtration accuracy (μm) to 00 Note ) Filtration area (cm 2 ) 770 420 How to Order ( Sub-element + Standard element equipped) element included FGF 20 E X46 It has a structure such that the spongiform filtration material, which is made of Polyvinylidene hlorides Saran staple fibers, is in the form of a bag. It is then fixed by a ring inside the standard element. Note ) Refer to "How to Order" (page 782) for the part of the part number. Note 2) When there is no option, the option symbol and the hyphen before the option symbol is not necessary. eg) FGFS-20-E00X46 / elements included FGF E Element material X46 Option Note 2) Nominal filtration accuracy Nominal filtration accuracy (μm) 00 00 0 02 2 00 0 00 00 X46 Standard element + Sub-element equipped Sub-element equipped How to Order (Sub-element equipped) Note ) element included FGF / elements included FGF 20 X8 X8 Note ) Refer to "How to Order" (page 782) for the part of the part number. Note 2) When there is no option, the option symbol and the hyphen before the option symbol is not necessary. eg) FGFS-20-X8 Sub-element/Ring Part No. l440 l770 Sub-element (single part) EZS40S EZS0S Option Note 2) X8 Sub-element equipped Nominal filtration accuracy is ranged from 00 to 000 μm. Sub-element with ring EZS20S EZS0S Ring (single part) FZS0S Note) Order a sub-element with a ring when you have already purchased a standard product. 788

Specifications 2 Please consult with SM for detailed size, specifications and delivery. Made to Order (For precision HEPO element equipped high performance filter material eliminates as much as 98% of the foreign matter with a size of μm. Filtration area is large which allows the service life to be extended. Optimum for filtration of precision machine fluids, precision cleaning fluids, etc. Effective for the grinding powders. Specifications ø90 x l440 ø90 x l770 Flow rate (l/min) Filtration accuracy (μm) (98% of filtered particle size) 0 to 00 0 to 200 Filtration area (cm 2 ) 6470 640 How to Order (HEPO element equipped) Note ) cylindrical element in which the filter material made of P.G.P. (Polyester + Glass fiber) is sandwiched by a stainless steel mesh and pleated. Note ) Refer to "How to Order" (page 782) for the part of the part number. Note 2) When there is no option, the option symbol and the hyphen before the option symbol is not necessary. eg) FGFS-20-Z00X49 element included FGF 20 Z 00 X49 / elements included FGF Z 00 X49 Note 2) Option Filtration accuracy μm (98% of filtered particle size) Element material X49 HEPO element equipped Element/Fixing Band/Spacer Part No. HEPO element (single part) Fixing band Spacer l440 EZFN20S Y-2XS O-XS l770 EZFN0S Note) Order a HEPO element (single part), a fixing band and a spacer together when you have already purchased a standard product. (For rough filtering) Long service life element equipped Long service life: Four to five times longer (compared with the standard elements) ost for maintenance is substantially reduced. Specifications Flow rate (l/min) Weak alkali queous coolant cleaning fluid ø90 x l440 ø90 x l770 to 0 0 to 00 2 to 00 0 to 200 Normal filtration accuracy (μm) pprox. 0 Filtration area (cm 2 ) 90 2400 How to Order (Long service life element equipped) Note ) element included FGF 20 Z 00 X82 cylindrical element in which the non-woven material made of P.P. (Polypropylene) is sandwiched by a PET mesh and pleated. Note ) Refer to "How to Order" (page 782) for the part of the part number. Note 2) When there is no option, the option symbol and the hyphen before the option symbol is not necessary. eg) FGFS-20-Z00X82 / elements included FGF Element/Fixing Band/Spacer Part No. l440 l770 Long service life element (single part) EZD80S-00 EZF70S-00 Fixing band Y-2XS Z 00 Element material Spacer O-XS Note) Order a long service life element (single part), a fixing band and a spacer together when you have already purchased a standard product. X82 Option Note 2) Nominal filtration accuracy X82 Long service life element equipped 789

Specifications Please consult with SM for detailed size, specifications and delivery. Made to Order Branch type element Element with l440 achieves the same life service as a l770 in a more compact size. Specifications ø90 x l440 Water-soluble coolant Flow rate (l/min) Weak alkali cleaning fluid to 0 2 to 00 Normal filtration accuracy (μm) to 00 Filtration area (cm 2 ) 280 How to Order (Branch type element equipped) Note ) Two-bag construction made of polyester non-woven material. Note ) Refer to "How to Order" (page 782) for the part of the part number. Note 2) When there is no option, the option symbol and the hyphen before the option symbol is not necessary. eg) FGFS-20-E00X98 FGF 20 Element material Nominal filtration accuracy 00 00 02 00 00 Nominal filtration accuracy (μm) 0 2 0 00 E Note 2) Option X98 Branch type element X98 Element Part No. Branch type element (single part) Note ) l440 EJS- Basket BT-2XS Note ) Enter the symbol for nominal filtration accuracy in the part. (Refer to page 782, How to Order.) Note 2) Order a branch type element (single part) and a basket together when you have already purchased a standard product. P.P. (Polypropylene) bag element equipped pplicable for strong alkali-based cleaning fluid an be used in various fields such as chemical plants, food plants, etc. Specifications Flow rate (l/min) Normal filtration accuracy (μm) Filtration area (cm 2 ) ø90 x l440 0 to 00 770 to ø90 x l770 0 to 200 420 How to Order (P.P. [Polypropylene] bag element equipped) Note ) element included FGF 20 E X72 / elements included FGF E X72 Note ) Refer to "How to Order" (page 728) for the part of the part number. Note 2) When there is no option, the option symbol and the hyphen before the option symbol is not necessary. eg) FGFS-20-Z00X72 Note 2) Option Nominal filtration accuracy Nominal filtration accuracy (μm) 00 00 00 790 Element Part No. l440 l770 Element material P.P. (Polypropylene) bag element (single part) EJ0S-X0 Note) EJ60S-X0 Note) X72 P.P. (Polypropylene) bag element equipped Note) Enter the symbol for nominal filtration accuracy in the part. (Refer to page 782, How to Order.)

Specifications 4 Please consult with SM for detailed size, specifications and delivery. Made to Order Filter paper element equipped Low pressure drop (approx. / compared with the standard type) and large filtration area makes it suitable for filtrating cutting fluids containing highly dense contaminants. Specifications ø90 x l440 ø90 x l770 Flow rate (l/min) Normal filtration accuracy (μm) 0 to 00 0 0 to 200 Filtration area (cm 2 ) 890 8469 How to Order (Filter paper element equipped) Note ) element included FGF 20 Z 00 X42 cylindrical element with a cotton-made filter inside and a pleated material on the outside for reinforcement. Note ) Refer to "How to Order" (page 782) for the part of the part number. Note 2) When there is no option, the option symbol and the hyphen before the option symbol is not necessary. eg) FGFS-20-Z00X42 / elements included FGF Z Element material 00 X42 Option Note 2) Nominal filtration accuracy X42 Filter paper element equipped Element/Fixing Band/Spacer Part No. l440 l770 Filter paper element (single part) EJ0S-00X6 EJ60S-00X6 Fixing band Y-2XS Spacer O-XS Note) Order a filter paper element (single part), a fixing band and a spacer together when you have already purchased a standard product. 79

Specifications Please consult with SM for detailed size, specifications and delivery. Made to Order Flange type cover is available with up to.0 MPa pressure. hinge mechanism and stopper mechanism are added to the cover to improve the job performance and safety. How to Order (High Pressure Spec.,.0 MPa Type) S L FGF 20 E X90 Body material Stainless steel 04 B Gasket, O-ring HNBR FKM Specifications ø90 x l440 ø90 x l770 20 Rc2 Element material X90 High pressure spec. (.0 MPa) Nominal filtration accuracy 00 00 02 00 00 Nominal filtration accuracy (μm) 0 2 0 00 Dimensions FGF (07) (9) 874 80 72 B..D 96 77 0 6 77 6 0 ø290 O.D 24 92 84 (280) 00 Vessel x ø20 M6 for foundation bolt Name plate Element Drain port in the inlet side in the outlet side Sø 74 669 Drain discharge ( B..D. 96) Model FGFS FGFL MX..0 MPa MX. 80 Operating pressure Operating temperature Gasket, O-ring material ccessory valve Nominal filtration accuracy Basket withstand differential pressure strength in the inlet side in the outlet side (47) B..D 96 (24) 204 0 77 6 0 ø290 O.D 24 0 92 84 (280) 00 x ø20 M6 for foundation bolt Sø 74 999 6 FGFB HNBR FKM Part No.: G46--02M, R/4 x ø42 x. MPa /4 B ball valve Polyester, 0, 2, 0, 00 μm 0. MPa Drain port Name plate in the inlet side in the outlet side in the inlet side in the outlet side 6 77 Drain discharge ( B..D. 96) 792 6

Specific Product Precautions Be sure to read this before handling. Refer to front matters 42 and 4 for Safety Instructions and consult instruction manuals for details Mishandling will likely cause fluid leakage or removal of a cover, which may lead to an unexpected accident. lso, adaptability of equipment should be determined by a fully knowledgeable and experienced system designer. Please be sure to observe the following precautions, taking into consideration the damage prevention of an element, preservation of the poduct peformance and the maintenance performance. Operating ondition Range Warning. Operating pressure Do not use the product above its pressure range. 2. Operating temperature Do not use the product above its temperature range. Operating fluids ) Never use the product with gases 2) Do not use the product with corrosive fluids ) Do not use the product with fluids which will likely cause the expansion and deterioration of O-rings or the element. 4. Operating environment ) Do not use the product in an atmosphere if it may be corrosive. 2) Do not use this product in a place where shock or vibrations occur. aution on Design and Installation aution. Pressure drop (ΔP) Use the product with a flow which has an initial pressure drop which will become 7 kpa or less 2. Installation space rrange the necessary space for inspection, before installing and piping the product.. Flushing Flush the piping line when the product is used during the initial stage. 4. onfirm IN/OUT before piping. Provide a circuit for releasing the air 6. When using the product at a high temperature, take measures to prevent a burn from occurring 7. Provide circuits for releasing drainage and fluids. Warning aution on Operation. Replace the elements only after confirming that the pressure is zero. (Open the air release valve.) 2. The parts used for tightening the cover (V-band, etc.) must be properly positioned when attached.. Replace the deteriorated or expanded O-ring or gasket. O-ring or gasket replacement should be performed within one year after usage or when fluid leakage occurs. (Reter to page 784. omponent parts and Seal list.) 4. When applying pressure for starting a pump, etc., be sure to release the air by opening the release valve on the top.. If a part used for tightening the cover is deformed or the threads are galled, it must not be used. (Refer to page 784, omponent parts and Seal list.) aution aution on Operation. Replacement of elements Replace the element only when the pressure drops (ΔP) reaches 0. MPa 2. Surface temperature of a filter onfirm that the surface temperature of the filter is 40 or less, to prevent a burn from occurring.. leaning of each component In order for firm sealing to take place, clean the sealing surface of the O-ring or gasket and/or remove the paint which is left on the tightened parts of the cover or the thread parts. 4. When applying a pressure to start up a pump, confirm that the valves in the piping are sealed when opened or closed and that each connecting parts are completely sealed. If any abnormality is found, such as air leakage, stop the product immediately. The possible cause of the failure should be located. Resume operation after taking appropriate measures to stop the air leakage, such as replacing the O-rings, or additionally tightening the fittings. 79

Specific Product Precautions 2 Be sure to read this before handling. Refer to front matters 42 and 4 for Safety Instructions and consult instruction manuals for details Be sure to following the precautions below, taking into consideration that the bag filter should not be damaged, the product performance should be maintained, and or inspection and maintenance should be conducted easily. aution. Use the product with a circuit having lesser fluctuation to the filter caused by pressure or flow. circuit aution on Installation and Piping. Pipe so that air releasing is absolutely performed. The air releasing job can be done firmly if you make the piping in order to flow a small flow constantly into a tank by resin tubing, etc. from the air releasing valve. (Refer to Fig. 2.) But, when the position of a pump is high, please use caution for an idle run when restarting. Pump Drain released To a tank Tubing ir releasing valve Tank Fluid releasing valve Foundation bolt Fig. Example of circuit (irculating filtration circuit) 2. Firmly fix the bottom to the ground using foundation bolts, etc.. onnect the valves or fittings suited to the operating conditions by confirming the size of each connection port. Prior to operating, flush the piping line and check for abnormalities, such as fluid leakage. 4. Provide a drain releasing valve and a fluid releasing valve. Fig. 2 ir releasing circuit 6. Piping such as for the INLET and OUTLET should be firmly fixed to the mounting frame using a saddle, to avoid vibration and or force caused from the weight. 794

Specific Product Precautions Be sure to read this before handling. Refer to front matters 42 and 4 for Safety Instructions and consult instruction manuals for details Element Replacement Warning over Removal aution Element Removal Valve opened Handle ir releasing valve Valve closed Element Basket over V-band Fig. Opening/losing the air releasing valve. Stop operation 2. lose the valve, starting from the inlet, then outlet.. Open the air release valve to allow the internal pressure of the filter to reach zero. Then open the drain valve and liquid discharging valve to completely drain the internal fluid. (Refer to fig. ) 4. To remove the cover and O-ring for inspection, loosen the nuts on the parts fastening the cover (V-band, etc.) Remove the cover by pulling upwards and turning it counterclockwise. (in the case of one element only). Replace the expanded O-rings with new ones. (Refer to page 784 for omponent parts and Seal list.) Basket Removal aution Handle Basket ase Fig. Removing an element. handle made of cloth is attached to the element so that it can be pulled out of the basket by using your fingers or a stick. Pull the handle towards the center. (Refer to Fig. ) [Elements for replacement] Part No.: EJ0S- (Size: ø90 x l440) Part No.: EJ60S- (Size: ø90 x l770) for nominal fitration accuracy (Refer to "How to order" on page 782.) Example of symbol for part number In the case of 0 μm EJ0S-00 aution. Please use caution in the case of high temperature to prevent burns. aution Element Installation Gasket Element Basket. ttach a handle to the notch and remove the basket by pulling upwards. (Refer to Fig. 4). ( handle is provided with the basket of the one element type). 2. Inspect the gasket in the case and replace it with a new one, if it is expanded. lso, remove any foreigh matter where the gasket is set. [Gaskets for replacement] Fig. 4 Basket removal Part No.: L-20S (: NBR) Part No.: L-2S (: FKM) Bottom part of an element Fig. 6 Element installation. Pull the cloth handle of a new element towards the center and fold the edge of the element. Then place it inside of the basket. Thoroughly push the edge of the element to the bottom plate's flange surface of the basket. (Refer to Fig. 6) 2. ttach a handle to the notch. (The handle is provided with the basket of the one element type). Grasp the handle and place the basket in the case. 4. Remove the handle from the basket.. Place the O-rings in the cover or case. 6. ttach the cover to the case. 79

Specific Product Precautions 4 Be sure to read this before handling. Refer to front matters 42 and 4 for Safety Instructions and consult instruction manuals for details Instalation and Fastening the over and V-band (pplicable only with one element included) Warning. Install the V-band in the edge of the cover and case correctly. (Refer to Fig. 7, 8.) 2. Gently strike the circumference around the V-band with a plastic hammer, etc. to fit the connection. V-band over Edge of the cover O-ring Warning 2. fter fastening the tightening nut to the prescribed position, insert the pin for confirming the tightening position. (Refer to Fig. 9.) Replace the V-band and O-ring with genuine parts when difficult to install the V-band. (Refer to page 784, omponent Parts and Seal List.) aution lean the contact surface of the V-band, cover and case prior to the attachment. ase Retainer Edge of the case Warning When there are deformation or galling in the threads for the V-band, replace it with a new one. [V-band for replacement] Part No.: Y-9S Fig. 7 How to install the V-band correctly. Warning In the event of setting the cover to the case, adjust the pins (two locations) to the guide slit of the case inside the cover, and push them thoroughly and turning clockwise. (Refer to Fig. 0.) Pin (Two locations) over Fig. 8 Example of installing the V-band incorrectly. (Fitting slanted) Warning. Install the T-bracket correctly in the latch. (Refer to Fig. 9.) T-bracket L Retainer ase Guide groove (Two locations) Bracket for V-band Fig. 0 How to set the cover Latch Tightening nut Pin for confirming the fastening position L = Tighten it until it becomes to 7 mm. (Reference tightening torque:.2 to.6 N m) Fig. 9 Tightening position of the V-band aution Restart and ir Release. When restarting this product after replacing the elements, follow the cautions on operation described in the back of page 79. 2. When restarting, be sure to open the air releasing valve on the top to release the air. 796