U SM Specifications Double acting, nonrotating type M Series Bore size:,,, JIS symbol Note: alue when stroke length is 0 mm (excluding deflection of piston rod). Double acting nonrotating cylinder single rod type M Bore size mm mm Actuation Working fluid Max. working pressure Min. working pressure Withstanding pressure Ambient temperature Port size MPa MPa MPa Double acting nonrotating type Compressed air 1.0 0.1 1.6 to 60 (no freezing) Rc1/8 +2.0 +2.4 Stroke tolerance 0 (up to 0), 0 (over 0) Working piston speed Cushion Lubrication mm/s 50 to 500 Rubber cushion Not required (when lubricating, use turbine oil Class 1 ISO G.) Revolvable angle tolerance (note) degree 1.5 1.0 Allowable energy absorption J 0.6 0.308 0.424 0.639 Stroke length Standard stroke length (mm), 50, 75, 0, 150, 0, 0, 300 Max. stroke length (mm) Min. stroke length (mm) 750 5 Note 1: Custom stroke length is available per 1 mm increment. Note 2: For single foot type (LS type), maximum stroke length is 50 mm. Note 3: For bellows "J" type, stroke length should be longer than mm. Consult with CKD when stroke length is shorter than mm. Min. stroke length of type with switch Switch quantity 1 T2, T3 T1, T*Y* T0, T5 T8 Note 1: Up to three switches can be mounted. 2 3 T2, T3 T1, T*Y* T0, T5 T8 T2, T3 T1, T*Y* 35 35 35 35 35 35 35 35 (Unit: mm) T0, T5 T8 6
M Series Specifications Switch specifications 1 color/2 color indicator Applications Output method Power voltage Load voltage Load current Light Leakage current Cylinder weight This is prod uct mass when stroke length (S) = 00 mm Switch weight /mounting style Switch rail Basic type Axial foot type Axial foot type Flange type Eye bracket type Clevis type Clevis bracket type Trunnion type Grommet + band weight (00) (LB) (LS) (FA/FB) (CA) (CC) (CB) (TA/TB) 0.17 0.26 0.30 0.48 0. 0.52 0.56 0.74 0. 0.39 0.43 0.61 0.23 0.41 0.45 0.63 0. 0.50 0.54 0.72 0.18 0.26 0.30 0.50 0. 0.50 0.54 0.72 0.22 0.36 0. 0.64 0.005 0.005 0.009 0.009 (E.g.) Product weight of MFA50T0HD 2wire 3wire 2wire T1H/T1 T2H/T2/ T2JH/T2J T2YH/T2Y T3PH/T3P T3H/T3 T3YH/T3Y (Custom order) TOH/TO T5H/T5 T8H/T8 controller controller, controller, relay, IC circuit (w/o light), Relay, small solenoid valve controller dedicated controller, relay controller, relay serial connection relay NPN output PNP output NPN output to 28 DC 85 to 265 AC to 30 DC 30 DC or less 12/24 DC 1 AC 5/12/24 DC 1 AC 12/24 DC 1 AC 2 AC 5 to 0 ma 5 to ma (Note 1) 0 ma or less 5 to 50 ma 7 to ma ma or less 5 to 50 ma 7 to ma 7 to ma LED LED Red/green LED Green Red/Green LED LED LED LED LED Without indicator light (ON lighting) (ON lighting) (ON lighting) (ON lighting) (ON lighting) (ON lighting) (ON lighting) (ON lighting) 1 ma or less with 0 AC 2 ma or less with 0 AC 1 ma or less A or less 0 ma With preventive maintenance output Applications Output method NPN output 3wire 4wire 3wire 4wire T2YFH/ controller dedicated T3YFH/ controller, relay T2YMH/ controller dedicated T3YMH/ controller, relay Installation position adjustment Red/Green LED (ON lighting) Preventive maintenance output Yellow LED (ON lighting) Power voltage Load voltage Load current to 30 DC 5 to ma to 28 DC 30 DC or less to 30 DC 5 to ma to 28 DC 30 DC or less Leakage current Load voltage 1 ma or less A or less 1.2 ma or less 30 DC or less A or less Load current ma or less 5 to ma or less Leakage current A or less Light Regular Output section Preventive maintenance Output section * The T0/T5 switch can be used with 2 AC. Contact CKD for working conditions. Note 1: Refer to 1 for other switches. Note 2: The above maximum load current of ma applies at. If the switch's working ambient temperature exceeds, the load current will be lower than ma. (5 to ma when 60 ) (Unit: kg) Additional weight per S = mm 0.01 0.01 0.02 0.02 When S = 00 mm, product weight is 0.45 kg Product stroke length (50) Additional weight at S = 50 mm is additional weight at S = mm 0.02 X = 0. kg Weight of two switches is 0.036 kg Weight of switch rail and two bands is kg Product weight is 0.45 kg + 0.1 kg + 0.036 kg + kg = 0.604 kg U SM Standard type 7
M Series U SM 8 How to order Without switch M 00 0 With switch M 00 0 T0H R A Mounting style Note 1 B Bore size Note on model no. selection <Example of model number> M000T0HRI C Port thread type Note 1: The maximum stroke of the singleend foot type (LS type) is 50 mm. Note 2: Refer to page 6 for min. stroke length with switch. Note 3: Applicable tube O.D. of F; pushin joint (straight), FE; pushin joint (elbow) is 6. Note 4: For bellows "J" type, stroke length should be more than mm. Consult with CKD when stroke length is shorter than mm. Note 5: Instantaneous maximum temperature is the temperature when spark and spatter etc. instantaneously contacts to bellows. Note 6: "I" "Y" can not be selected at the same time. Note 7: Refer to 89 for the custom order specifications of rod end form. Note 8: Refer to page 84 for variation and combinations of options. Note 9: Up to three switches can be mounted. If more than four switches are required, switch mounting brackets for the extra switches must be prepared separately. D Stroke length Model:, double acting, nonrotating type A Mounting style : Basic type B Bore size : mm C Port thread type : Rc thread D Stroke length : 0 mm E Switch model no. : reed T0H switch, lead wire 1 m F Switch quantity : One on rod end G Option : Boss cut off H Accessory : Rod eye E Switch model no. I I F Switch quantity Note 9 G Option Note 3, Note 4, Note 5 H Accessory Note 6 Symbol A Mounting style 00 Basic type LB Axial foot type (both sides) LS Axial foot type (single) FA Rod side flange type FB Head side flange type CA Eye bracket type CC Fixed eye CC1 Eye and bush press fitted type CB Clevis bracket type (pin and washer split pin attached) TA Rod side trunnion type TB Head side trunnion type B G Option * Lead wire length Blank 1 m (standard) 3 3 m (option) 5 5 m (option F Switch quantity R One on rod end H One on head end D Two T Three J L F FE M C Port thread type Blank Rc thread NN NPT thread (custom order) GN G thread (custom order) D Stroke length (mm) Bore size Stroke length Note 2 Custom stroke length E Switch model no. Lead wire Lead wire Straight type L type T0H* T0* T5H* T5* T8H* T8* T1H* T1 * T2H* T2* T3H* T3* T3PH* T3P* T2YH* T2Y* T3YH* T3Y* T2YFH* T2YF* T3YFH* T3YF* T2YMH* T2YM* T3YMH* T3YM* T2JH* T2J* Contact Bellows Bellows Indicator 1 color Without indicator light 1 color 1 color 1 color (custom order) 2 color 2 color (w/o light for preventive maintenance output) 2 color (Light available for preventive maintenance output (1 color)) Offdelay type Max. ambient 0 By 1 mm increment Lead wire 2wire 2wire 3wire 3wire 2wire 3wire 3wire 4 wire 3wire 4 wire 2wire Max. instanteneous 0 0 0 Pushin joint (straight) Pushin joint (elbow) Boss cut off Piston rod material (stainless steel) H Accessory I Rod eye Y Rod clevis (pin and washer split pin attached) B2 Clevis bracket (pin and snap ring attached)
How to order switch Switch body + mounting bracket T0H How to order mounting bracket Mounting bracket Only switch body SW T0H Axial foot type (LB/LS) Flange (FA/FB) Trunnion (TA) Eye bracket type (CA) Clevis bracket type (CB) M1LB M1FA M1TA M1CA M1CB M1LB30 M1FA30 M1TA30 M1CA30 M1CB30 Note 1: Mounting nut/toothed washer are attached to each mounting bracket. Note 2: Two sets of "M1LB*" in the above table are required for the axial direction foot (doublesided). Mounting bracket T M Series How to order Bore size (item B on previous page) Bore size Switch model no. (item E on previous page) Switch model no. (item E on previous page) (item B on previous page) Bracket M1LB30 M1FA30 M1TA30 M1CA30 M1CB30 M1LB30 M1FA30 M1TA M1CA30 M1CB30 U SM Standard type 9
M Series U SM Internal structure and parts list M Note: This caulking type cannot be disassembled. No. Parts name Material Remarks 1 Rod nut 2 Piston rod Stainless steel 3 Rod packing seal Nitrile rubber 4 Bush : Dry bearing,, : Copper 5 Rod cover Aluminum alloy 6 Cylinder tube Stainless steel 7 Cushion rubber Urethane rubber 8 Piston A Aluminum alloy 9 Piston packing seal Nitrile rubber Magnet Plastic 11 Wear ring Polyacetal 12 Piston B Aluminum alloy 13 Head cover Aluminum alloy Mounting bracket material Mounting style LB/LS FA/FB TA/TB CA CB 1 2 18 19 3 17 4 5 21 6 7 8 9 11 12 13 14 15 Material Note: Mounting bracket is attached to the product when shipped. No. Parts name Material Remarks 14 15 17 Hexagon nut Spacer Nut The toothed washer 18 Round R type snap ring Phosphoric acid zinc 19 Packing gland Nonrotating bush Copper oil impregnated alloy 21 Taper pin Stainless steel 170
Dimensions Basic type (00) T type with switch MT RD: Rod side max. sensitive position HD: Head side max. sensitive position Symbol Symbol A HA P1 Rod section cross section B 13 23 17 23 17 19 With switch GC GD 4.0 3.0 5.5 4.5 5.5 4.5 7.0 6.5 C 18 22 RD 8.0 9.5 9.5 11.5 P D 21.4 26.4 33.6 41.6 HD (P ) 8 7.0 8.5 8.5.5 F 28 36 45 P 17.3 19.8 24.3 28.3 d HA 26 35 35 35 P1 19.5 22.0.5 29.5 KK Width across flats B X + A b Note 1: Refer to page 188 for the HD, RD, and projecting dimensions of the T1* and T8* switches and 2color indicator switch with preventive maintenance output. Note 2: For dimensions, round up decimal point or less. Note 3: Refer to page 190 for dimensions of accessories. K X + stroke length A WF LL + stroke length C GC 30.5 8 RD T MM MB XF + stroke length WF + (with bellows) KK LL MB 2Rc1/8 MM MT 12 M8 x 1.0 66 M18 x 1.5 8 14 M x 1. 69 M26 x 1.5 12 14 M x 1. 69 M26 x 1.5 12 14 M12 x 1.5 73 M26 x 1.5 14 12 With bellows (P ) b d 22 30 30 (stroke length/3) + 6 18 46 (stroke length/3.) + 7 15 46 (stroke length/3.) + 7 12 34 46 (stroke length/3.) + 7 Dimensions of each mounting type are same as standard type. Refer to pages 96 to 1. D 2width across flats U T 5 6 6 7 U 24 30 34 43 14 WF 24 23 23 23 X 124 131 131 137 XE 80 85 85 89 XF 44 46 46 48 U SM Standard type XE + stroke length M Series Double acting nonrotating type 30.5 HD GD 8 MB K F 171