Rotary Cutter RCF3696 & RCFM3696 33422 326-600P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2018 Printed 07/10/18 Cover photo may show optional equipment not supplied with standard unit.
Table of Contents Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Section 2: Deck...6 Deck Components...6 Section 3: Hitch & Tail Wheel...8 Axle Lift Hydraulic or Manual 3-Point...8 Axle Lift Hydraulic or Manual Pull Type/Semi-Mount...10 Hitch 3-Point...12 Hitch Pull Type Tounge S/N 1151135-...14 Hitch Pull Type Tounge S/N 1151136+...16 Hydraulic Cylinder (810-384C) Cross...18 Performance Hitch...20 Swivel Hitch...22 Tail Wheel 3-Point W/ 15" Lam. Tire...24 Transport Axle 3-Point & Semi-Mount W/ 15" Lam. Tire...26 Transport Axle 3-Point & Semi-Mount W/ 21" Lam. Tire...28 Transport Axle Pull Type...30 Section 4: Blade Drive 1000 RPM...32 Blade Carrier CCW...32 Blade Carrier CW...34 Blade Drive 3-Point & Semi-Mount...36 Blade Drive Pull Type W/ CV...38 Blade Drive Pull Type W/ Equal Angle...40 Driveline CV Pull Type Cutter 1000 RPM (826-063C) Walterscheid...42 Driveline Flex Coupler (826-224C) Eurocardan...44 Driveline Jackshaft (1000 RPM) (826-259C) Eurcardan...46 Driveline Lift Type Cutter 1000 RPM (826-258C) Eurocardan...48 Driveline Pull Type Conv. 1000 RPM (826-223C) Eurocardan...50 Driveline Slip Clutch (1406128) EC...52 Driveline Slip Clutch 1000 RPM (1406116) Eurocardan...54 Driveline Slip Clutch 540/1000 RPM (1446016) EC...56 Driveline Stub Shaft Pull Type 1000 RPM (826-226C) Eurocardan...58 Gearbox (826-424C) Comer...60 Gearbox (826-718C)...62 Section 4: Blade Drive 540 RPM...64 Blade Carrier CCW...64 Blade Carrier CW...66 Blade Drive 3-Point & Semi-Mount...68 Blade Drive Pull Type W/ CV...70 Blade Drive Pull Type W/ Equal Angle...72 Driveline Conv. Fixed Shaft Pull Type 540 RPM (826-151C) Eurocardan...74 Driveline CV Pull Type Cutter 540 RPM (826-053C) Walterscheid...76 Driveline Flex Coupler (826-224C) Eurocardan...78 Driveline Jackshaft (540 RPM) (826-256C) Eurcardan...80 Driveline Lift Type Cutter 540 RPM (826-255C) Eurocardan...82 Driveline Slip Clutch (1446137) Eurocardan...84 Driveline Slip Clutch 540/1000 RPM (1446016) EC...86 Driveline Stub Shaft Pull Type 540 RPM (826-225C) Eurocardan...88 Gearbox (826-718C)...90 Gearbox...92 T-Box 540 RPM (826-356C) Comer...92 Section 5: Guards...94 Chain Guard Dual Front...94 Chain Guard Single Front...96 Guard Chain Dual Rear...98 Guard Chain Single Rear...100 Guard Rubber Front...102 Guard Rubber Rear...104 Section 6: Decals...106 Decal Placement 3-Point...106 Decal Placement Pull Type...108 Touch-up Paints...110...112 Copyright 2018. All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Alphabetized Table of Contents A B C D G Axle Lift Hydraulic or Manual 3-Point...8 Axle Lift Hydraulic or Manual Pull Type/Semi-Mount...10 Blade Carrier CCW...32 Blade Carrier CCW...64 Blade Carrier CW...34 Blade Carrier CW...66 Blade Drive 3-Point & Semi-Mount...36 Blade Drive 3-Point & Semi-Mount...68 Blade Drive Pull Type W/ CV...38 Blade Drive Pull Type W/ CV...70 Blade Drive Pull Type W/ Equal Angle...40 Blade Drive Pull Type W/ Equal Angle...72 Chain Guard Dual Front...94 Chain Guard Single Front...96 Decal Placement 3-Point...106 Decal Placement Pull Type...108 Deck Components...6 Driveline Conv. Fixed Shaft Pull Type 540 RPM (826-151C) Eurocardan...74 Driveline CV Pull Type Cutter 1000 RPM (826-063C) Walterscheid...42 Driveline CV Pull Type Cutter 540 RPM (826-053C) Walterscheid...76 Driveline Flex Coupler (826-224C) Eurocardan...44 Driveline Flex Coupler (826-224C) Eurocardan...78 Driveline Jackshaft (1000 RPM) (826-259C) Eurcardan...46 Driveline Jackshaft (540 RPM) (826-256C) Eurcardan...80 Driveline Lift Type Cutter 1000 RPM (826-258C) Eurocardan...48 Driveline Lift Type Cutter 540 RPM (826-255C) Eurocardan...82 Driveline Pull Type Conv. 1000 RPM (826-223C) Eurocardan...50 Driveline Slip Clutch (1406128) EC...52 Driveline Slip Clutch (1446137) Eurocardan...84 Driveline Slip Clutch 1000 RPM (1406116) Eurocardan...54 Driveline Slip Clutch 540/1000 RPM (1446016) EC...56 Driveline Slip Clutch 540/1000 RPM (1446016) EC...86 Driveline Stub Shaft Pull Type 1000 RPM (826-226C) Eurocardan...58 Driveline Stub Shaft Pull Type 540 RPM (826-225C) Eurocardan...88 Gearbox (826-424C) Comer...60 Gearbox (826-718C)...62 Gearbox (826-718C)...90 H L P S T Gearbox, T-Box 540 RPM (826-356C) Comer...92 Guard Chain Dual Rear...98 Guard Chain Single Rear...100 Guard Rubber Front...102 Guard Rubber Rear...104 Hitch 3-Point...12 Hitch Pull Type Tounge S/N 1151135-...14 Hitch Pull Type Tounge S/N 1151136+...16 Hydraulic Cylinder (810-384C) Cross...18 Touch-up Paints...110 Performance Hitch...20 Swivel Hitch...22 Tail Wheel 3-Point W/ 15" Lam. Tire...24 Transport Axle 3-Point & Semi-Mount W/ 15" Lam. Tire...26 Transport Axle 3-Point & Semi-Mount W/ 21" Lam. Tire...28 Transport Axle Pull Type...30 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 3
4 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 5
Deck Components Applies to RCF3696, RCFM3696 Section 2: Deck 33423 6 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Deck Components Section 2: Deck Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 Dwg 33423 326-428H 326-428h81 326-428h82 326-428h83 326-479D 802-224C 802-603C 803-198C 803-255C 804-007C 816-504C 840-273C 332-014D 802-585C 803-037C Drawing Image Number 3696 DECK WELDMENT 3696 DECK WELDMENT GREEN 3696 DECK WELDMENT ORANGE 3696 DECK WELDMENT RED SKID SHOE HHCS 1/4-20X1 1/4 GR5 PLOW 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT MANUAL STORAGE CONTAINER PLUG LP 3" ID RUBBER RCF REFLECTOR BRACKET RHSNB 1/2-13X3 1/2 GR5 PLT NUT HEX WHIZ 1/2-13 PLT S/N 813017+ S/N 813017+ S/N 813017+ 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 7
Axle Lift Hydraulic or Manual 3-Point Applies to RCF3696, RCFM3696 Section 3: Hitch & Tail Wheel 35175 8 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Axle Lift Hydraulic or Manual 3-Point Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 Dwg 35175 312-729D 326-494A 326-508A 326-564H 326-500H 802-017C 802-184C 802-205C 803-013C 803-026C 803-168C 803-263C 804-012C 806-184C 807-023C 810-384C 810-818C 811-133C 811-394C 811-676C 811-676C 890-637C Drawing Image Number HOSE HOLDER BRACKET HYDRAULIC LIFT - 3-PNT RATCHET JACK BUNDLE AXLE LUG 96" AXLE LUG HHCS 3/8-16X1 GR5 HHCS 3/4-10X1 1/2 GR5 HHCS 1-8X5 1/2 GR5 NUT LOCK 3/8-16 PLT NUT LOCK 3/4-10 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX FLANGE LOCK 5/8-11 PLT WASHER FLAT 3/8 SAE PLT U-BOLT 5/8-11 X 4 1/32 X 5 1/2 SPRING HOSE LOOP CYL 3X6X25 ROD (TIE ROD) STRK CNTRL SPCRS 125 TO 50 AD 9/16MJIC 3/4MORB CP 3/4FORB MALE QD POPPET TYPE HH3/8R1 144 3/4MORB 9/16FJIC HH3/8R1 144 3/4MORB 9/16FJIC RATCHET JACK 16.25-225 15" Laminated Tire 21" Laminated Tire 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 9
Axle Lift Hydraulic or Manual Pull Type/Semi-Mount Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 33453 10 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Axle Lift Hydraulic or Manual Pull Type/Semi-Mount Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 20. 2 2 2 2 25. 26. 27. 28. 29. 30. 30. 3 3 3 3 35. Dwg 33453 312-729D 326-491A 326-492H 326-587H 326-508A 326-564H 326-912D 326-988D 330-294D 800-306C 802-017C 802-184C 802-205C 802-254C 802-269C 802-762C 803-013C 803-026C 803-147C 803-148C 803-168C 803-258C 803-168C 803-263C 804-012C 804-017C 806-184C 807-023C 807-271C 810-384C 810-818C 811-394C 811-633C 811-676C 811-694C 812-388C 841-103C 841-284C 890-637C Drawing Image Number HOSE HOLDER BRACKET HYDRAULIC LIFT SPRING SHOCK SPRING SHOCK 10PT RATCHET JACK BUNDLE AXLE LUG 96" TRUNNION ARM TRUNNION ARM 10PT SPACER TRUNNION ARM FILL PLUG VENTED 3/4-16 PLT HHCS 3/8-16X1 GR5 HHCS 3/4-10X1 1/2 GR5 HHCS 1-8X5 1/2 GR5 HHCS 5/8-11X5 1/2 GR5 HHCS 1/2-13X9 GR5 HHCS 1-8X6 1/2 GR8 NUT LOCK 3/8-16 PLT NUT LOCK 3/4-10 PLT NUT HEX NYLOCK 1/2-13 NUT HEX NYLOCK 5/8-11 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX FLANGE LOCK 5/8-11 PLT WASHER FLAT 3/8 SAE PLT WASHER FLAT 1/2 USS PLT U-BOLT 5/8-11 X 4 1/32 X 5 1/2 SPRING HOSE LOOP SPRING COMP 20OD.63W 5.5L CYL 3X6X25 ROD (TIE ROD) STRK CNTRL SPCRS 125 TO 50 CP 3/4FORB MALE QD POPPET TYPE HH3/8R1 162 3/4MORB 9/16 FJIC HH3/8R1 144 3/4MORB 9/16FJIC ORAD 1/32 9/16MORB 9/16MJIC SWIVEL CAST AD 3/4MORB 9/16FORB OREL 1/16 9/16MJIC 3/4MORB RATCHET JACK 16.25-225 Semi Mount Unit Pull Type Unit Semi Mount Unit Pull Type Unit S/N + S/N - S/N 749047+ S/N 749046- S/N 835072- S/N 835072- S/N 835073+ 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 11
Hitch 3-Point Table of Contents Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 33424 12 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Section 3: Hitch & Tail Wheel Hitch 3-Point Table of Contents Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. 29. 29. 30. 3 3 3 3 3 35. 36. 37. 38. 39. Dwg 33424 312-821D 312-931D 326-530H 326-531H 326-591D 326-891D 326-916D 326-917D 326-002D 326-947D 326-982D 802-057C 802-064C 802-098C 802-169C 802-205C 802-908C 803-026C 803-028C 803-038C 803-168C 803-271C 804-025C 804-026C 804-029C 805-017C 805-088C 805-090C 805-088C 805-103C 805-137C 805-485C 805-274C 327-143S 802-010C 802-138C 803-177C 804-036C 807-350C 837-062C 837-063C Drawing Image Number BSHG 1 1/4ODX1 1/32IDX2 1/16LG REAR BRACE STRAIGHT LONG A-FRAME LH A-FRAME RH HITCH MOUNT BSHG REAR BRACE SHORT BSHG 1OD X 11GWLX.44 REAR BRACE STRAIGHT TUBE 1 OD X 11/16 LG. X 5/32w REAR BRACE FORMED TUBE RND 1 1/4ODX12GWX.84 HHCS 5/8-11X2 1/4 GR5 HHCS 3/4-10X2 GR5 HHCS 1-8X4 1/2 GR5 HHCS 1-8X3 1/2 GR5 HHCS 1-8X5 1/2 GR5 HHCS 7/8-9X2 1/2 GR5 NUT LOCK 3/4-10 PLT NUT NY-LOK 7/8-9 PLT NUT HEX 1-8 NYLON INSERT PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX TOP LOCK 5/8-11 PLT WASHER FLAT 3/4 SAE PLT WASHER FLAT 7/8 SAE PLT WASHER FLAT 1 SAE PIN COTTER 3/16 X 1 3/4 PLT PIN, HAIR COTTER 3/16 WIRE DIA PIN CLEVIS 1 X 3 3/16 LG PIN, HAIR COTTER 3/16 WIRE DIA PIN LINCH 7/16 X 1 3/4 PIN CLEVIS 1 X 2 PLT PIN, HITCH 3PT CAT 1&2 PIN HITCH CAT.I-II DRIVELINE HOLDER W/ HARDWARE HHCS 5/16-18X1 1/4 GR5 HHCS 5/16-18X2 1/4 GR5 NUT HEX LOCK 5/16-18 FLG. WASHER FLAT 5/16 SAE PLT SPRING TORSION DRIVELINE HLDER DRIVELINE HOOK MOUNT DRIVELINE HOOK S/N 983493+ S/N 983492- S/N 983493+ S/N 983492- S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 13
Hitch Pull Type Tounge S/N 1151135- Applies to RCF3696, RCFM3696 Section 3: Hitch & Tail Wheel 33827 14 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Hitch Pull Type Tounge S/N 1151135- Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 5. 6. 6. 7. 8. 9. 10. 10. 1 1 1 1 1 15. 16. 17. 17. 18. 19. 19. 20. 20. 2 2 Dwg 33827 312-421H 312-733D 318-008H 330-404H 326-495H 326-556K 326-934K 326-557H 326-933H 802-074C 802-096C 802-098C 803-075C 803-030C 803-168C 803-265C 803-375C 804-025C 804-028C 804-029C 804-125C 805-045C 805-109C 805-083C 805-088C 805-103C 805-485C 805-274C 890-118C 891-246C Drawing Image Number CLEVIS WELDMENT TUBE 1 5/8 OD X 7/32 WL X1 LG. WLDMT. LEVEL ROD SHORT LEVEL ROD SHORT 1" TONGUE WELDMENT 30/3696-10 LEVEL ROD ASSY. LEVEL ROD ASY, SHORT LEVEL ROD LONG 1" LEVEL ROD, SHORT HHCS 1-8X6 1/2 GR5 HHCS 1-8X2 1/2 GR5 HHCS 1-8X4 1/2 GR5 NUT HEX JAM 7/8-9 NUT HEX JAM 1-8 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX COUPLER 7/8-9 x 5 NUT HEX COUPLER 1-8 X 5 WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 USS PLT WASHER FLAT 1 SAE WASHER BELLEVILLE 1ID PIN COTTER 5/32 X 1 1/4 LG PIN COTTER 1/8 X 1 1/4 PLT PIN CLEVIS 3/4 X 1 1/2 PIN, HAIR COTTER 3/16 WIRE DIA PIN LINCH 7/16 X 1 3/4 PIN, HITCH 3PT CAT 1&2 PIN HITCH CAT.I-II SCREW JACK 2000# 14-24 TOP-WND AG SAFETY CHAIN 6400 LB For 7/8" leveling rod For 1" leveling rod 7/8" leveling rod kit 1" leveling rod kit 7/8" leveling rod 1" leveling rod For 7/8" leveling rod For 1" leveling rod For 7/8" leveling rod For 1" leveling rod For 7/8" & 1" leveling rod For 7/8" leveling rod For 1" leveling rod For 7/8" & 1" leveling rod S/N 983493+ S/N 983492- S/N 983493+ S/N 983492-07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 15
Hitch Pull Type Tounge S/N 1151136+ Applies to RCF3696, RCFM3696 Section 3: Hitch & Tail Wheel 70102 16 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Hitch Pull Type Tounge S/N 1151136+ Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 5. 6. 6. 7. 8. 9. 10. 1 1 1 1 1 1 15. 16. 17. 18. 18. 19. 20. 2 Dwg 70102 312-733D 326-557H 326-933H 326-889H 326-891H 318-008H 330-404H 326-556K 326-934K 802-096C 802-106C 803-020C 803-031C 803-075C 803-030C 803-168C 803-265C 803-375C 804-015C 804-025C 804-027C 804-029C 805-045C 805-109C 805-083C 890-118C 891-246C Image No. TUBE 1 5/8 OD X 7/32 WL X1 LG. LEVEL ROD LONG 1" LEVEL ROD, SHORT TONGUE ADJUSTABLE JACK MOUNT WLDMT. LEVEL ROD SHORT LEVEL ROD SHORT 1" LEVEL ROD ASSY. LEVEL ROD ASY, SHORT HHCS 1-8X2 1/2 GR5 RHSNB 1/2-13X1 1/2 GR5 NUT HEX 1/2-13 PLT NUT HEX 1-8 PLT NUT HEX JAM 7/8-9 NUT HEX JAM 1-8 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX COUPLER 7/8-9X5 NUT HEX COUPLER 1-8 X 5 WASHER LOCK SPRING 1/2 PLT WASHER FLAT 3/4 SAE PLT WASHER LOCK SPRING 1 PLT WASHER FLAT 1 SAE PIN COTTER 5/32 X 1 1/4 LG PIN COTTER 1/8 X 1 1/4 PLT PIN CLVS.75X50 USBL HT SCREW JACK 2000# 14-24 TOP-WND AG SAFETY CHAIN 6400 LB 7/8" Leveling rod 1" Leveling rod For 7/8" leveling rod For 1" leveling rod 7/8" Leveling rod kit 1" Leveling rod kit For 7/8" leveling rod For 1" leveling rod For 7/8" leveling rod For 1" leveling rod For 7/8" leveling rod For 1" leveling rod 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 17
Hydraulic Cylinder (810-384C) Cross Applies to RCF3696, RCFM3696 Section 3: Hitch & Tail Wheel 33918 18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Hydraulic Cylinder (810-384C) Cross Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. Dwg 33918 810-384C 1D1205-8 N/A 1D1401-300 N/A 1D0007-850 1D0206-1075 1D1157-17 N/A 2A0235-8 N/A 2A0580-1100 2A0246-12 1D1003-5 2A0079-616 2A0235-6 805-032C 1D1551-16275 810-009C Drawing Image Number CYL 3X6X25 ROD (TIE ROD) * CROSS, BASE CLEVIS CROSS, O-RING CROSS PISTON 3 BORE CYLINDER CROSS, BACK-UP CROSS, TUBE CROSS, ROD CROSS HEAD 3 BORE CYLINDER WIPER SEAL CROSS CROSS NUT, TIE ROD CROSS U-CUP CROSS,TIE ROD CROSS NUT, PISTON CROSS ROD CLEVIS CROSS SCREW, CAP CROSS NUT, CLEVIS & TIE ROD PIN HAIR COTTER.148 WIRE CROSS CLEVIS PIN CYL SEAL KIT 3 (CROSS) In Seal Kit Item #18 In Seal Kit Item #18 In Seal Kit Item #18 In Seal Kit Item #18 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 19
Performance Hitch Applies to RCF3696, RCFM3696 Section 3: Hitch & Tail Wheel 70104 20 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Performance Hitch Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. Dwg 70104 334-007A 334-049H 334-050H 334-066H 802-070C 802-365C 803-019C 803-181C Drawing Image Number (LPH) PERFORMANCE HTCH SLF LVL * HITCH SELF LEVELING 5D SHFT HITCH CLEVIS SELF LEVELING BSHG HITCH LOCK/STOP 56 ID HHCS 3/4-10X6 GR5 HHCS 1/2-13X3 GR8 NUT LOCK 1/2-13 PLT NUT HEX FLANGE LOCK 3/4-10 PLT 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 21
Swivel Hitch Table of Contents Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 70103 22 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Section 3: Hitch & Tail Wheel Swivel Hitch Table of Contents Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision Dwg 70103 334-006A 334-004H 334-066H 802-365C 803-019C Drawing Image Number SWIVEL CLEVIS * SWIVEL CLEVIS STRAIGHT BSHG HITCH LOCK/STOP 56 ID HHCS 1/2-13X3 GR8 NUT LOCK 1/2-13 PLT 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 23
Tail Wheel 3-Point W/ 15" Lam. Tire Applies to RCF3696, RCFM3696 Section 3: Hitch & Tail Wheel 33425 24 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Tail Wheel 3-Point W/ 15" Lam. Tire Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. 29. Dwg 33425 326-606H 312-616D 312-811D 800-001C 800-080C 802-106C 802-135C 802-162C 802-280C 802-326C 803-026C 803-037C 803-271C 803-289C 803-308C 804-015C 804-016C 804-066C 805-255C 814-058C 814-161C 815-092C 815-230C 815-231C 816-286C 822-091C 822-092C 827-036C 890-961C Drawing Image Number TAILWHEEL BEAM WELDMENT INTRM. TAILWHEEL ARM ADJUST PLATE TAILWHEEL BEAM MOUNTING BRKT. GREASE ZERK STRAIGHT 1/4-28 GREASE ZERK 1/4-28 THD FORMING RHSNB 1/2-13X1 1/2 GR5 HUB STUD 1/2-20X1 5/8 GR5 HHCS 5/8-11X3 1/2 GR5 HHCS 3/4-10X7 1/2 GR5 HHCS 1/2-20X1 1/4 GR5 NUT LOCK 3/4-10 PLT NUT HEX WHIZ 1/2-13 PLT NUT HEX TOP LOCK 5/8-11 PLT NUT HEX 1 1/4-7(MACHINED)PLAIN NUT HEX FLG/LK 1/2-20 PLT GR G WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER MACH 25 X 50 X 14GA PIN ROLL 3/8 X 2 1/2 PLT TIRE & WHEEL LAMINATED 0 X 8 LAM 4X8 TR-WL-HUB-YOKE 25 SER. HUB & SPINDLE ASSY 4 BOLT HUB 4 BLT W/CUPS, ZERK & STUDS HUB 4BLT DUCTILE(USE 815-230C) OIL SEAL DBL LIP 441 BORE BRG 25ID CONE 15123 BRG CUP 44OD 15245 BUSHING TW 25ODX.78IDX5 1/4 RC25 TAILWHEEL YOKE As Required As Required As Required As Required 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 25
Transport Axle 3-Point & Semi-Mount W/ 15" Lam. Tire Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 33356 26 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Transport Axle 3-Point & Semi-Mount W/ 15" Lam. Tire Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. Dwg 33356 326-488H 326-559H 326-968D 800-001C 800-080C 802-135C 802-280C 802-326C 802-360C 803-026C 803-263C 803-289C 803-308C 804-015C 804-016C 804-066C 805-255C 806-184C 814-058C 814-161C 815-092C 815-230C 815-231C 816-286C 822-091C 822-092C 827-036C 890-961C Drawing Image Number 3-PNT TAILWHEEL MOUNT AXLE 96" PIVOT SPACER BUSHING GREASE ZERK STRAIGHT 1/4-28 GREASE ZERK 1/4-28 THD FORMING HUB STUD 1/2-20X1 5/8 GR5 HHCS 3/4-10X7 1/2 GR5 HHCS 1/2-20X1 1/4 GR5 HHCS 3/4-10X6 1/2 GR5 NUT LOCK 3/4-10 PLT NUT HEX FLANGE LOCK 5/8-11 PLT NUT HEX 1 1/4-7(MACHINED)PLAIN NUT HEX FLG/LK 1/2-20 PLT GR G WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER MACH 25 X 50 X 14GA PIN ROLL 3/8 X 2 1/2 PLT U-BOLT 5/8-11 X 4 1/32 X 5 1/2 TIRE & WHEEL LAMINATED 0 X 8 LAM 4X8 TR-WL-HUB-YOKE 25 SER. HUB & SPINDLE ASSY 4 BOLT HUB 4 BLT W/CUPS, ZERK & STUDS HUB 4BLT DUCTILE(USE 815-230C) OIL SEAL DBL LIP 441 BORE BRG 25ID CONE 15123 BRG CUP 44OD 15245 BUSHING TW 25ODX.78IDX5 1/4 RC25 TAILWHEEL YOKE As Required As Required As Required As Required As Required 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 27
Transport Axle 3-Point & Semi-Mount W/ 21" Lam. Tire Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 33357 28 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Transport Axle 3-Point & Semi-Mount W/ 21" Lam. Tire Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. 29. 30. 3 3 Dwg 33357 312-067K 312-084L 312-100H 312-231D 326-496H 326-559H 326-968D 800-001C 800-080C 802-135C 802-272C 802-326C 802-360C 803-026C 803-027C 803-263C 803-289C 803-308C 804-015C 804-016C 804-023C 804-074C 805-255C 806-184C 814-059C 815-092C 815-230C 815-231C 816-286C 822-091C 822-092C 827-036C Drawing Image Number RC35 TAILWHEEL ASSY-21 RC 35 TW & YOKE ASSY RC35 YOKE WLDMT TAILWHEEL WASHER SEMI-MOUNT TAILWHEEL ARM AXLE 96" PIVOT SPACER BUSHING GREASE ZERK STRAIGHT 1/4-28 GREASE ZERK 1/4-28 THD FORMING HUB STUD 1/2-20X1 5/8 GR5 HHCS 3/4-10X10 GR5 HHCS 1/2-20X1 1/4 GR5 HHCS 3/4-10X6 1/2 GR5 NUT LOCK 3/4-10 PLT NUT HEX 3/4-10 PLT NUT HEX FLANGE LOCK 5/8-11 PLT NUT HEX 1 1/4-7(MACHINED)PLAIN NUT HEX FLG/LK 1/2-20 PLT GR G WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER LOCK SPRING 3/4 PLT WASHER MACH 25 X 75 X 10GA PIN ROLL 3/8 X 2 1/2 PLT U-BOLT 5/8-11 X 4 1/32 X 5 1/2 TIRE & WHEEL LAM. 6X9X21(TALL) HUB & SPINDLE ASSY 4 BOLT HUB 4 BLT W/CUPS, ZERK & STUDS HUB 4BLT DUCTILE(USE 815-230C) OIL SEAL DBL LIP 441 BORE BRG 25ID CONE 15123 BRG CUP 44OD 15245 BUSHING TW 25ODX.78IDX5 1/4 As Required As Required As Required As Required As Required 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 29
Transport Axle Pull Type Applies to RCF3696, RCFM3696 Section 3: Hitch & Tail Wheel 33426 30 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Transport Axle Pull Type Section 3: Hitch & Tail Wheel Applies to RCF3696, RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 19. 19. 20. 2 2 2 2 25. 26. 27. 28. 29. 30. 3 Dwg 33426 200-001D 326-489H 326-559H 326-968D 330-938K 800-080C 802-099C 802-360C 802-779C 803-019C 803-026C 803-029C 803-263C 803-310C 804-055C 805-246C 806-184C 814-265C 814-444C 814-478C 814-449C 815-242C 815-243C 815-401C 815-402C 816-497C 822-020C 822-021C 822-033C 822-034C 814-450C 814-451C 814-461C Drawing Image Number HUB GREASE CAP PULL TAILWHEEL AXLE 96" PIVOT SPACER BUSHING HUB 5 BOLT COMPLETE GREASE ZERK 1/4-28 THD FORMING HHCS 1/2-13X3 1/4 GR5 HHCS 3/4-10X6 1/2 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT LOCK 3/4-10 PLT NUT HEX SLOTTED 7/8-14 PLT NUT HEX FLANGE LOCK 5/8-11 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG U-BOLT 5/8-11 X 4 1/32 X 5 1/2 TIRE & WHL LAM. 6X9X21(5-BOLT) RPBY 814-478C NEW TIRE FF 25.5X8-14 20PLY TIRE, AC 29" 16 PLY 5 BOLT HUB 5-BOLT CASTING HUB 5-BOLT W/CUPS/STUDS SPINDLE, SINGLE BOLT-ON 7/8-14 SPINDLE, DUAL BOLT-ON 7/8-14 SEAL 75ID CR17617 BRG CUP LM-67010 BRG CONE 25ID LM-67048 BRG CUP LM-48510 BRG CONE LM-48548 TIRE H29X9.0X15 USED TUBE FOR 29X9.0-15 RIM 2PC 5BLT 15X6.5 Foam Filled 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 31
Blade Carrier CCW Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 33427 32 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Carrier CCW Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. Dwg 33427 326-433S 312-082D 312-075D 312-089D 312-808D 326-430H N/A 802-277C 803-170C 804-147C 820-195C 318-586A Drawing Image Number ASSY CCW BLADE CARRIER * BLADE SPACER 18 GA..052 THICK BLADE SPACER 16 GA..064 THICK BLADE SPACER 20 GA..04 THICK BLADE SPACER 24 GA..03 THICK 3696 DISHPAN ASSY CCW BLADE CARRIER BLD BLT 1 1/8-12X44 W/.25KEY NUT HEX TOP LOCK 1 1/8-12 PLT. WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X20 1/2 CCW BLADE BOLT KIT As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- As Required S/N 776426-07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 33
Blade Carrier CW Table of Contents Section 4: Blade Drive 1000 RPM Applies to RCFM3696 33428 34 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Carrier CW Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. Dwg 33428 312-082D 312-075D 312-089D 312-808D 326-430H N/A 802-277C 803-170C 804-147C 820-196C 318-586A Drawing Image Number BLADE SPACER 18 GA..052 THICK BLADE SPACER 16 GA..064 THICK BLADE SPACER 20 GA..04 THICK BLADE SPACER 24 GA..03 THICK 3696 DISHPAN ASSY CW BLADE CARRIER BLD BLT 1 1/8-12X44 W/.25KEY NUT HEX TOP LOCK 1 1/8-12 PLT. WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X20 1/2 CW BLADE BOLT KIT As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- As Required S/N 776426-07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 35
Blade Drive 3-Point & Semi-Mount Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 33429 36 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Drive 3-Point & Semi-Mount Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 7. 8. 8. 9. 10. 1 1 1 1 15. 15. 16. 16. 17. 18. 19. 20. 20. Dwg 33429 312-508H 312-509H 326-941D 802-034C 802-212C 802-065C 802-314C 802-007C 803-299C 804-009C 804-015C 804-036C 817-259C 826-224C 826-255C 826-258C 826-356C 826-424C 826-486C 826-503C 826-718C 837-101C 826-648C Drawing Image Number SHIELD BRACKET WELDMENT SHIELD BRACKET WELDMENT SEE BLADE CARRIER CCW FOR COMPONENTS SEE BLADE CARRIER CW FOR COMPONENTS OUTER SHIELD 96 HHCS 1/2-13X1 1/4 GR5 HHCS 3/4-10X2 1/2 GR5 RPBY 802-212C HHCS M8X25X20 GR8.8 HHCS 5/16-18X3/4 GR5 NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 5/16 SAE PLT KNOB 3/8-16 FEMALE THD 2 3/8OD FLEX COUPLER 1 3/4-20 (9.21) PTO STD.W/4-PLATE SC CAT4 540 PTO STD.W/2-PLATE SC CAT4 1000 T-BOX 75-20 1:35 T-BOX 75-20 35:1 COMER U0.125.70000 DIPSTICK COMER VENT 8.6.7.00161 GBOX RCF36 75-20 1:77 STD LAND PRIDE CONE LARGE SHAFT CONE W ACCESS DOOR S/N + S/N - RCF3696 RCFM3696 RCF3696 RCFM3696 This cone has been replaced with 837-101C 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 37
Blade Drive Pull Type W/ CV Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 35174 38 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Drive Pull Type W/ CV Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 2 2 25. 25. 26. 27. 28. 29. 29. Dwg 35174 312-508H 312-509H 326-941D 327-228D 800-080C 801-035C 802-034C 802-042C 802-082C 802-212C 802-065C 802-314C 802-007C 803-037C 803-299C 804-009C 804-015C 804-016C 804-036C 817-259C 822-094C 826-053C 826-063C 826-224C 826-225C 826-226C 826-356C 826-424C 826-486C 826-503C 826-718C 837-101C 826-648C Drawing Image Number SHIELD BRACKET WELDMENT SHIELD BRACKET WELDMENT SEE BLADE CARRIER CCW FOR COMPONENTS SEE BLADE CARRIER CW FOR COMPONENTS OUTER SHIELD 96 PILLOW BLOCK BEARING SUPPORT GREASE ZERK 1/4-28 THD FORMING SCREW SET 5/16-18 SKT KP X 3/8 HHCS 1/2-13X1 1/4 GR5 HHCS 1/2-13X3 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HHCS 3/4-10X2 1/2 GR5 RPBY 802-212C HHCS M8X25X20 GR8.8 HHCS 5/16-18X3/4 GR5 NUT HEX WHIZ 1/2-13 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER FLAT 5/16 SAE PLT KNOB 3/8-16 FEMALE THD 2 3/8OD BRG PB 37ID PTO CV 2400 X 60 540 RPM PTO CV 2400 X 60 1000 RPM FLEX COUPLER 1 3/4-20 (9.21) PTO W/STUB SHAFT/SC 540 1 3/4 PTO W/STUB SHAFT/SC 1000 1 3/4 T-BOX 75-20 1:35 T-BOX 75-20 35:1 COMER U0.125.70000 DIPSTICK COMER VENT 8.6.7.00161 3/8MNPT GBOX RCF36 75-20 1:77 STD LAND PRIDE CONE LARGE SHAFT CONE W ACCESS DOOR S/N + S/N - RCF3696 RCFM3696 RCF3696 RCFM3696 RCF3696 RCFM3696 This cone has been replaced with 837-101C 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 39
Blade Drive Pull Type W/ Equal Angle Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 33430 40 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Drive Pull Type W/ Equal Angle Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 8. 9. 9. 10. 1 1 1 1 1 1 1 1 15. 15. 15. 16. 17. 18. 19. 19. 19. 20. 2 2 2 2 2 25. 25. 26. 26. 27. 28. 29. 30. 30. Dwg 33430 312-508H 312-509H 312-999D 326-002D 326-941D 327-571D 312-833D 327-593D 312-715D 800-069C 802-034C 802-212C 802-065C 802-280C 802-146C 802-260C 802-314C 802-007C 803-026C 803-019C 803-021C 803-299C 804-009C 804-015C 804-024C 804-021C 804-022C 804-036C 817-259C 822-100C 826-151C 826-223C 826-224C 826-256C 826-259C 826-356C 826-424C 826-486C 826-503C 826-718C 837-101C 826-648C Drawing Image Number SHIELD BRACKET WELDMENT SHIELD BRACKET WELDMENT CASTING TRUNION MACHINED TUBE 1 OD X 11/16 LG. X 5/32w SEE BLADE CARRIER CCW FOR COMPONENTS SEE BLADE CARRIER CW FOR COMPONENTS OUTER SHIELD 96 TRUNNION SUPPORT SUPPORT UPRIGHT TRUNION TRUNION SPACER PIPE 1/2 SCH. 40 X 4 15/16 SNAP RING INT 835 HHCS 1/2-13X1 1/4 GR5 HHCS 3/4-10X2 1/2 GR5 RPBY 802-212C HHCS 3/4-10X7 1/2 GR5 HHCS 5/8-11X7 1/2 GR5 HHCS 1/2-13X7 GR5 HHCS M8X25X20 GR8.8 HHCS 5/16-18X3/4 GR5 NUT LOCK 3/4-10 PLT NUT LOCK 1/2-13 PLT NUT HEX 5/8-11 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 3/4 USS PLT WASHER FLAT 5/8 SAE PLT WASHER LOCK SPRING 5/8 PLT WASHER FLAT 5/16 SAE PLT KNOB 3/8-16 FEMALE THD 2 3/8OD BRG INS 37IDX83OD LOCK PTO CAT. 4 X 20.5 FIXED 540 PTO CAT. 4 X 22 FIXED 1000 FLEX COUPLER 1 3/4-20 (9.21) PTO J/S.W/4-PLATE SC CAT4 540 PTO J/S.W/2-PLATE SC CAT4 1000 T-BOX 75-20 1:35 T-BOX 75-20 35:1 COMER U0.125.70000 DIPSTICK COMER VENT 8.6.7.00161 GBOX RCF36 75-20 1:77 STD LAND PRIDE CONE LARGE SHAFT CONE W ACCESS DOOR S/N + S/N - S/N + S/N - S/N + S/N - S/N - S/N + S/N - S/N + S/N - S/N - S/N + S/N - S/N - RCF3696 RCFM3696 RCF3696 RCFM3696 RCF3696 RCFM3696 This cone has been replaced with 837-101C 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 41
Driveline CV Pull Type Cutter 1000 RPM (826-063C) Walterscheid Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 10452 42 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline CV Pull Type Cutter 1000 RPM (826-063C) Walterscheid Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. 28. Dwg 10452 826-063C 320684 020469 30008 010490 695581 020672 365722 342221 019519 020617 383084 321245 134713 383334 377341 365305 087276 044321 384064 383333 388434 172758 312410 355155 386083 380371 390404 826-589C 359471 Drawing Image Number PTO CV 2400 X 60 1000 RPM * WS YOKE 1 3/8-21 SPL WS BOLT M12 X 75 COSMO SELF LOCK NUT M12 RPBY 30008 WS YOKE 1 3/8-21 ASGE WS GREASE ZERK WS DOUBLE YOKE WS CROSS & BEARING KIT WS INBOARD YOKE WS SPRING PIN 10 X 20 WS PROFILE & SLEEVE WS INNER PROFILE 16 GA WS INBOARD YOKE 1B WALTERSCHEID DNGR DECAL-STEEL WS SHIELD CONE 11 RIB WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS INNER SHIELD TUBE-ROUND WALTERSCHEID DANGER DECAL-SHLD WS OUTER SHIELD TUBE OVL WS SHIELD CONE 3 RIB WS CROSS BEARING KIT WS SUPPORT BEARING WS CV CONE & BEARING ASSY WS ZERK WS ASGE COLLAR KIT SHIELD KIT, 826-063C WS REINFORCING COLLAR Obsolete S/N 928934-07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 43
Driveline Flex Coupler (826-224C) Eurocardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 16886 44 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Flex Coupler (826-224C) Eurocardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. Dwg 16886 826-224C 1705278 1785273 1005220 6560208 312-608A Drawing Image Number FLEX COUPLER 1 3/4-20 (9.21) EC BOLT EC SPIDER 1 3/4-20 W/TAP HOLE EC WSH. BD. 35mm O.D/16.5mm I.D EC BOLT BUSHING EC RUBBER DISC EC WASHER 29.8mm O.D/17.2mm I.D EC NUT EC SPIDER TUBE EC GREASE ZERK M8 STRAIGHT FLEX COUPLER KIT Only sold in kit #10 1 3/4-20 Only sold in kit #10 Only sold in kit #10 Can be ordered seperately & in kit #10 Only sold in kit #10 Only sold in kit #10 S/N 639636- Includes items 1, 3, 4, 5, 6 & 7 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 45
Driveline Jackshaft (1000 RPM) (826-259C) Eurcardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 16173 46 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Jackshaft (1000 RPM) (826-259C) Eurcardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 6. 7. 8. 8. 9. 10. 1 1 1 1 1 15. 16. 16. 17. 18. 19. 20. 2 Dwg 16173 826-259C 1786711 1215733 1885702 1215735 1885709 1877305 1877066 044321 1876305 1876066 1885705 1786710 1896315N327 1896071N327 6331070 1526070 1706029 1006020 1406128 1406028 818-552C 818-540C 6560508 6561306 826-571C Drawing Image Number PTO J/S.W/2-PLATE SC CAT4 1000 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHIELD RPBY 1877305 DRIVELINE SHIELD SAFETY CHAIN EC OUTER TUBE SHIELD RPBY 1876305 EC EXTRA SHORT CONE (FOR MX) EC TUBE BEARING (OUTER TUBE) EC OUTER TUBE ASSEMBLY RPBY 1896315N327 EC 10X70 ROLL PIN EC INNER TUBE (1526084) 840MM EC INNER TUBE YOKE EC CROSS ASSEMBLY EC TORQUE LIMITER, (FD 2) RPBY 1406128 DECAL DANGER PTO DRIVELINE DECAL DANGER GUARD MISS PTO EC GREASE ZERK 8X1 45 DEG. EC GREASE ZERK M6X1 EXTRA SHRT SHIELD KIT, 826-259C S/N 670486+ S/N 670485- S/N 928934- S/N 670486+ S/N 670485- S/N 670486+ S/N 670485- S/N 670486+ 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 47
Driveline Lift Type Cutter 1000 RPM (826-258C) Eurocardan Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 22283 48 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Lift Type Cutter 1000 RPM (826-258C) Eurocardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. Dwg 22283 826-258C 1786711 1215733 1885702 1215735 1885709 1877052 1876052 1885703 1786710 1406116 1406016 1006020 1706029 1526062 6331070 1528062 6331080 1706027 1016015 818-540C 818-552C 044321 6560508 1004220 6560006 1016017 1004225 826-569C Drawing Image Number PTO STD.W/2-PLATE SC CAT4 1000 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHEILD EC OUTER TUBE SHEILD EC STANDARD CONE EC TUBE BEARING (OUTER TUBE) EC CLUTCH FD2/6 1 3/4" Z20 RPBY 1406116 EC CROSS ASSEMBLY EC INNER TUBE YOKE EC INNER TUBE (1526084) 620MM EC 10X70 ROLL PIN EC OUTER TUBE (1528084) 620MM EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC YOKE ASSEMBLY (TRACT. END) DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT (TRT. END) EC GREASE ZERK M6X1 STRAIGHT EC YOKE ASSEMBLY (TRACTOR END) EC PULL COLLAR KIT SHIELD KIT, 826-255C &826-258C 1 3/8-21 S/N 928934-1 3/8-21 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 49
Driveline Pull Type Conv. 1000 RPM (826-223C) Eurocardan Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 6370a 50 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Pull Type Conv. 1000 RPM (826-223C) Eurocardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. Dwg 16370a 826-223C 1016013 1006020 1706027 6331080 1528044D 1016013 1786710 1215733 1885703 1215735 1885709 1876034D 1885704 91SL6034D 044321 818-552C 818-540C 1004227 1004227 826-568C Drawing Image Number PTO CAT. 4 X 22 FIXED 1000 * EC YOKE ASSEMBLY EC CROSS ASSEMBLY EC OUTER TUBE YOKE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE EC YOKE ASSEMBLY EC TUBE BRG (OUTER TUBE) EC STIFFENING RING EC STANDARD CONE EC STOP RING EC SAFETY SLEEVE EC OUTER TUBE (1876094) 340MM EC LONG CONE EC COMPLETE PROTECTION DRIVELINE SHIELD SAFETY CHAIN DECAL DANGER PTO DRIVELINE DECAL DANGER GUARD MISS PTO EC PULL COLLAR KIT EVOLUTION EC PULL COLLAR KIT EVOLUTION SHIELD KIT, 826-223C S/N 928934-07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 51
Driveline Slip Clutch (1406128) EC Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 30197 52 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Slip Clutch (1406128) EC Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. Dwg 30197 1406128 1706033 1706314 803-279C 6001085 1215010 1138007 1138008 1808010 6761480 1705009 Drawing Image Number EC TORQUE LIMITER, (FD 2) * EC CLUTCH YOKE W/FLANGE FD2 HUB 1 3/4 WITH FLANGE NUT HEX M10X5 PLT EC BOLT (M10X85) EC SPRING EC PRESSURE DISK EC INNER DISK EC CLUTCH LINING RING EC BOLT, NUT & WASHER KIT EC CLUTCH BUSHING 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 53
Driveline Slip Clutch 1000 RPM (1406116) Eurocardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 33826 54 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Slip Clutch 1000 RPM (1406116) Eurocardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 Dwg 33826 1406116 1707033 1708017 803-279C 6001085 1215010 1138007 1138008 1808010 6821484 1236039 6410614 6412014 1705009 Drawing Image Number EC CLUTCH FD2/6 1 3/4" Z20 * EC FD2-4/6 FLANGE WITH YOKE EC HUB WITH FLANGE NUT HEX M10X5 PLT EC BOLT (M10X85) EC SPRING EC PRESSURE DISK EC INNER DISK EC CLUTCH LINING RING CONICAL DOG KIT RPBY 6821484 EC SELF LOCK SCREW NUT (M14) EC WASHER (D14) EC CLUTCH BUSHING 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 55
Driveline Slip Clutch 540/1000 RPM (1446016) EC Section 4: Blade Drive 1000 RPM Applies to RCFM3696 15521 56 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Slip Clutch 540/1000 RPM (1446016) EC Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 dwg15521 1446016 1215012 1706033 1705009 1808010 1708034 1138008 1708016 6821484 1138007 6691010 330-297A Drawing Image Number EC CLUTCH FD4/6 1 3/4 20 SPL * RPBY 330-297A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC CLUTCH MIDDLE DISK EC INNER DISK EC HUB WITH FLANGE EC CONICAL DOG KIT REPLACEMENT EC PRESSURE DISK EC BOLT & SCREW NUT KIT REPL. SV KIT, EC SLIP CLUTCH SPRING Includes nut and washer Contains 8 Springs 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 57
Driveline Stub Shaft Pull Type 1000 RPM (826-226C) Eurocardan Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 15995 58 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Stub Shaft Pull Type 1000 RPM (826-226C) Eurocardan Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 9. 10. 1 1 1 1 1 15. 16. Dwg 15995 826-226C 1786710 1215733 1885702 1215735 1885709 044321 1876025D 1885705 1896030S821 1896030D821 6331080 1706027 1006020 1406116 1406016 818-552C 818-540C 6560508 Drawing Image Number PTO W/STUB SHAFT/SC 1000 1 3/4 * EC TUBE BEARING (OUTER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE DRIVELINE SHIELD SAFETY CHAIN EC OUTER TUBE SHEILD EC EXTRA SHORT CONE (FOR MX) EC OUTER TUBE ASSY (HRDND) EC OUTER TUBE ASSY EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC CROSS ASSEMBLY EC CLUTCH FD2/6 1 3/4" Z20 RPBY 1406116 DECAL DANGER PTO DRIVELINE DECAL DANGER GUARD MISS PTO EC GREASE ZERK 8X1 45 DEG. S/N 928934- Rev. 2 Rev. 1 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 59
Gearbox (826-424C) Comer Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 22348 60 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Gearbox (826-424C) Comer Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. Dwg 22348 826-424C 0.279.0305.00 0.278.71000 8.00501 0.279.3016.00 0.257525.00 0.279.50000 0.279.60000 0.257510.00 8.00978 8.7.02686 0.279.1315.00 8.0.9.00107 0.279.20100 0.279.13100 8.0.9.00125 8.7.02685 A25500 8.6.6.00201 8.6.7.00161 Drawing Image Number T-BOX 75-20 35:1 * CO CASING CO NUT LOCK M45 X 5 CO BOLT M10X22 HHB CO THROUGH SHAFT 1 3/4" Z20 CO SHIM 45.3X5 CO GEAR PINION Z20 M5.7 CO GEAR CROWN Z27 M5.7 CO SHIM (45.3X65.3X1) CO PARALLEL KEY B 14 X 9 X 40 CO DUST LIP 45 X 72 X 8 CO COVER CO RL BRG 30309 (45X100X27.25) CO INPUT SHAFT 1 3/4" Z20 CO EXTENSION CO BEARING 32209 CO OIL SEAL 52 X 85 X 10 CO SHIM 65.3MM RTA25 CO PLUG 3/8 GAS CO OIL FILLER PLUG 3/8 * Notes: Oil Type 80-90W Capacity 5.5 Pints 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 61
Gearbox (826-718C) Applies to RCFM3696 Section 4: Blade Drive 1000 RPM 33448 62 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Gearbox (826-718C) Section 4: Blade Drive 1000 RPM Applies to RCFM3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 25. 26. 27. Dwg 33448 826-718C U0.125.05300 U0.125.6007.00 8.0.9.00143 8.7.00331 U0.125.2000.03 8.5.00332 A.709.500 8.5.00533 0.137107.00 A.71500 8.0.9.01090 1871000 8.7.02349 8.0.9.00079 U0.125.3005.00 8.7.02265 0.1271000 0.288.71000 0.257525.00 0.285.7510.00 U0.125.13000 8.00501 826-486C 8.6.5.00006 8.7.01045 8.00560 U0.125.5007.00 Drawing Image Number GBOX RCF36 75-20 1:77 STD * CO CASTING & MACHINING CO GEAR CROWN Z23 M7.7 CO BRG 30209 TAPPERED CO OIL SEAL 45 X 85 X 10 SL CO 1 3/4" Z20 INPUT SHAFT CO SNAP RING UNI 7437 COMER SHIM KIT CO SNAP RING 50 UNI7435 CO NUT M40X5 COMER SHIM KIT CO BRG 32210 TAPPERED CO SEAL PROTECTOR CO OIL SEAL 60X110X12 SL CO BRG 30212 TAPPERED CO OUTPUT SHAFT CO COTTER PIN B 5X60 CO CAP CO BLANK WASHER CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO TOP COVER CO BOLT M10X22 HHB COMER U0.125.70000 DIPSTICK CO OIL PLUG 3/8 CO COTTER PIN B6X70 SLD-SPRTLY CO CASTLE NUT M36X3 CO GEAR PINION Z13 M7.7 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 63
Blade Carrier CCW Applies to RCF3696 Section 4: Blade Drive 540 RPM 33427 64 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Carrier CCW Section 4: Blade Drive 540 RPM Applies to RCF3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. Dwg 33427 326-433S 312-082D 312-075D 312-089D 312-808D 326-430H N/A 802-277C 803-170C 804-147C 820-195C 318-586A Drawing Image Number ASSY CCW BLADE CARRIER * BLADE SPACER 18 GA..052 THICK BLADE SPACER 16 GA..064 THICK BLADE SPACER 20 GA..04 THICK BLADE SPACER 24 GA..03 THICK 3696 DISHPAN ASSY CCW BLADE CARRIER BLD BLT 1 1/8-12X44 W/.25KEY NUT HEX TOP LOCK 1 1/8-12 PLT. WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X20 1/2 CCW BLADE BOLT KIT As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- As Required S/N 776426-07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 65
Blade Carrier CW Table of Contents Section 4: Blade Drive 540 RPM Applies to RCF3696 33428 66 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Carrier CW Section 4: Blade Drive 540 RPM Applies to RCF3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. Dwg 33428 312-082D 312-075D 312-089D 312-808D 326-430H N/A 802-277C 803-170C 804-147C 820-196C 318-586A Drawing Image Number BLADE SPACER 18 GA..052 THICK BLADE SPACER 16 GA..064 THICK BLADE SPACER 20 GA..04 THICK BLADE SPACER 24 GA..03 THICK 3696 DISHPAN ASSY CW BLADE CARRIER BLD BLT 1 1/8-12X44 W/.25KEY NUT HEX TOP LOCK 1 1/8-12 PLT. WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X20 1/2 CW BLADE BOLT KIT As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- As Required S/N 776426-07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 67
Blade Drive 3-Point & Semi-Mount Applies to RCF3696 Section 4: Blade Drive 540 RPM 33429 68 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Drive 3-Point & Semi-Mount Section 4: Blade Drive 540 RPM Applies to RCF3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 7. 8. 8. 9. 10. 1 1 1 1 15. 15. 16. 16. 17. 18. 19. 20. 20. Dwg 33429 312-508H 312-509H 326-941D 802-034C 802-212C 802-065C 802-314C 802-007C 803-299C 804-009C 804-015C 804-036C 817-259C 826-224C 826-255C 826-258C 826-356C 826-424C 826-486C 826-503C 826-718C 837-101C 826-648C Drawing Image Number SHIELD BRACKET WELDMENT SHIELD BRACKET WELDMENT SEE BLADE CARRIER CCW FOR COMPONENTS SEE BLADE CARRIER CW FOR COMPONENTS OUTER SHIELD 96 HHCS 1/2-13X1 1/4 GR5 HHCS 3/4-10X2 1/2 GR5 RPBY 802-212C HHCS M8X25X20 GR8.8 HHCS 5/16-18X3/4 GR5 NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 5/16 SAE PLT KNOB 3/8-16 FEMALE THD 2 3/8OD FLEX COUPLER 1 3/4-20 (9.21) PTO STD.W/4-PLATE SC CAT4 540 PTO STD.W/2-PLATE SC CAT4 1000 T-BOX 75-20 1:35 T-BOX 75-20 35:1 COMER U0.125.70000 DIPSTICK COMER VENT 8.6.7.00161 GBOX RCF36 75-20 1:77 STD LAND PRIDE CONE LARGE SHAFT CONE W ACCESS DOOR S/N + S/N - RCF3696 RCFM3696 RCF3696 RCFM3696 This cone has been replaced with 837-101C 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 69
Blade Drive Pull Type W/ CV Applies to RCF3696 Section 4: Blade Drive 540 RPM 35174 70 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Drive Pull Type W/ CV Section 4: Blade Drive 540 RPM Applies to RCF3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 1 1 15. 16. 17. 18. 19. 20. 2 2 2 2 2 2 25. 25. 26. 27. 28. 29. 29. Dwg 35174 312-508H 312-509H 326-941D 327-228D 800-080C 801-035C 802-034C 802-042C 802-082C 802-212C 802-065C 802-314C 802-007C 803-037C 803-299C 804-009C 804-015C 804-016C 804-036C 817-259C 822-094C 826-053C 826-063C 826-224C 826-225C 826-226C 826-356C 826-424C 826-486C 826-503C 826-718C 837-101C 826-648C Drawing Image Number SHIELD BRACKET WELDMENT SHIELD BRACKET WELDMENT SEE BLADE CARRIER CCW FOR COMPONENTS SEE BLADE CARRIER CW FOR COMPONENTS OUTER SHIELD 96 PILLOW BLOCK BEARING SUPPORT GREASE ZERK 1/4-28 THD FORMING SCREW SET 5/16-18 SKT KP X 3/8 HHCS 1/2-13X1 1/4 GR5 HHCS 1/2-13X3 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HHCS 3/4-10X2 1/2 GR5 RPBY 802-212C HHCS M8X25X20 GR8.8 HHCS 5/16-18X3/4 GR5 NUT HEX WHIZ 1/2-13 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER FLAT 5/16 SAE PLT KNOB 3/8-16 FEMALE THD 2 3/8OD BRG PB 37ID PTO CV 2400 X 60 540 RPM PTO CV 2400 X 60 1000 RPM FLEX COUPLER 1 3/4-20 (9.21) PTO W/STUB SHAFT/SC 540 1 3/4 PTO W/STUB SHAFT/SC 1000 1 3/4 T-BOX 75-20 1:35 T-BOX 75-20 35:1 COMER U0.125.70000 DIPSTICK COMER VENT 8.6.7.00161 3/8MNPT GBOX RCF36 75-20 1:77 STD LAND PRIDE CONE LARGE SHAFT CONE W ACCESS DOOR S/N + S/N - RCF3696 RCFM3696 RCF3696 RCFM3696 RCF3696 RCFM3696 This cone has been replaced with 837-101C 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 71
Blade Drive Pull Type W/ Equal Angle Applies to RCF3696 Section 4: Blade Drive 540 RPM 33430 72 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Blade Drive Pull Type W/ Equal Angle Section 4: Blade Drive 540 RPM Applies to RCF3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 8. 9. 9. 10. 1 1 1 1 1 1 1 1 15. 15. 15. 16. 17. 18. 19. 19. 19. 20. 2 2 2 2 2 25. 25. 26. 26. 27. 28. 29. 30. 30. Dwg 33430 312-508H 312-509H 312-999D 326-002D 326-941D 327-571D 312-833D 327-593D 312-715D 800-069C 802-034C 802-212C 802-065C 802-280C 802-146C 802-260C 802-314C 802-007C 803-026C 803-019C 803-021C 803-299C 804-009C 804-015C 804-024C 804-021C 804-022C 804-036C 817-259C 822-100C 826-151C 826-223C 826-224C 826-256C 826-259C 826-356C 826-424C 826-486C 826-503C 826-718C 837-101C 826-648C Drawing Image Number SHIELD BRACKET WELDMENT SHIELD BRACKET WELDMENT CASTING TRUNION MACHINED TUBE 1 OD X 11/16 LG. X 5/32w SEE BLADE CARRIER CCW FOR COMPONENTS SEE BLADE CARRIER CW FOR COMPONENTS OUTER SHIELD 96 TRUNNION SUPPORT SUPPORT UPRIGHT TRUNION TRUNION SPACER PIPE 1/2 SCH. 40 X 4 15/16 SNAP RING INT 835 HHCS 1/2-13X1 1/4 GR5 HHCS 3/4-10X2 1/2 GR5 RPBY 802-212C HHCS 3/4-10X7 1/2 GR5 HHCS 5/8-11X7 1/2 GR5 HHCS 1/2-13X7 GR5 HHCS M8X25X20 GR8.8 HHCS 5/16-18X3/4 GR5 NUT LOCK 3/4-10 PLT NUT LOCK 1/2-13 PLT NUT HEX 5/8-11 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 3/4 USS PLT WASHER FLAT 5/8 SAE PLT WASHER LOCK SPRING 5/8 PLT WASHER FLAT 5/16 SAE PLT KNOB 3/8-16 FEMALE THD 2 3/8OD BRG INS 37IDX83OD LOCK PTO CAT. 4 X 20.5 FIXED 540 PTO CAT. 4 X 22 FIXED 1000 FLEX COUPLER 1 3/4-20 (9.21) PTO J/S.W/4-PLATE SC CAT4 540 PTO J/S.W/2-PLATE SC CAT4 1000 T-BOX 75-20 1:35 T-BOX 75-20 35:1 COMER U0.125.70000 DIPSTICK COMER VENT 8.6.7.00161 GBOX RCF36 75-20 1:77 STD LAND PRIDE CONE LARGE SHAFT CONE W ACCESS DOOR S/N + S/N - S/N + S/N - S/N + S/N - S/N - S/N + S/N - S/N + S/N - S/N - S/N + S/N - S/N - RCF3696 RCFM3696 RCF3696 RCFM3696 RCF3696 RCFM3696 This cone has been replaced with 837-101C 07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 73
Driveline Conv. Fixed Shaft Pull Type 540 RPM (826-151C) Eurocardan Applies to RCF3696 Section 4: Blade Drive 540 RPM 16610 74 RCF3696 & RCFM3696 Rotary Cutter 326-600P 07/10/18
Driveline Conv. Fixed Shaft Pull Type 540 RPM (826-151C) Eurocardan Section 4: Blade Drive 540 RPM Applies to RCF3696 Ref. Part No. Part Description Comments Revision 5. 6. 7. 8. 9. 10. 1 1 1 1 15. 16. 17. 18. Dwg 16610 826-151C 1786710 1215733 1885704 1215735 1885709 1876030D 1885703 1006020 1706027 6331080 1528040D 818-540C 818-552C 044321 6560508 1016012 1004225 826-578C Drawing Image Number PTO CAT. 4 X 20.5 FIXED 540 * EC TUBE BEARING (OUTER TUBE) EC STIFFENING RING EC LONG CONE EC STOP RING EC SAFETY SLEEVE EC OUTER TUBE SHIELD EC STANDARD CONE EC CROSS ASSEMBLY EC OUTER TUBE YOKE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. YOKE ASSEMBLY PULL TYPE EC PULL COLLAR KIT SHIELD KIT, 826-151C S/N 928934-07/10/18 RCF3696 & RCFM3696 Rotary Cutter 326-600P 75