efore using the product, please check the Pressure ontrol Valves JIS graphic symbols for hydraulic system Refer to the next page. Features These direct operated control valves can be used as sequence valves, unload valves, counter balance valves, or relief valves by changing the combination of internal and external pilot and drain settings. 1 3 5 Nomenclature - JQ - - - - 1 3 5 7 8 9 pplicable fluid code No designation: Petroleum-based hydraulic fluid, water-glycol hydraulic fluid F: Phosphate ester hydraulic fluid Model No. JQ: JQ type control valve heck valve code No designation: Without check valve : With check valve onnections G: Gasket mount type T: Screw connection type F: Flange connection type Nominal diameter 3: ⅜ : ¾ 1: 1¼ 1: Function code (See JIS graphic symbols for hydraulic system)* 1 : Sequence valve (internal pilot type, external drain type) <With no option code designation> ounter balance valve (internal/external pilot type, external drain type) <With W option code designation> Pressure adjustment range : 5 to.85 MPa {.5 to 8.5 kgf/cm } :.85 to 3.5 MPa {8.5 to 35 kgf/cm } : 3.5 to 1 MPa {35 to 1 kgf/cm } : 1.75 to 7 MPa {17.5 to 7 kgf/cm }* esign No. (The design No. is subject to change) : Gasket mount type (G), screw connection type (T) : Flange mount type (F) <With nominal diameter of (¾), 1 (1¼)> 1: Flange mount type (F) <With nominal diameter of 1 ()> Option code No designation: Single pilot type(internal or external pilot type) W: ouble pilot type(internal and external pilot type) Note: * 1 The products are supplied with a function code of as standard. If a product with a function code of 1, 3 or is required, change the setting by referring to the setting guide on Page -. fter changing the setting, correct the model code marked on the nameplate. * Pressure adjustment range code is only applicable to nominal diameter code 1 (). ontact aikin separately for the delivery term of the products that accept phosphate ester hydraulic fluids. Specifications 7 8 9 Model code Maximum Nominal Pressure adjustment range operating Gasket mount type (G) Screw connection type (T) Flange mount type (F) diameter MPa {kgf/cm MPa {kgf/cm } } JQ()-G3- - JQ()-T3- - 5 to.85 {.5 to 8.5} JQ()-G3- --(W) JQ()-T3- --(W) ⅜.85 to 3.5 { 8.5 to 35 } JQ()-G3- --(W) JQ()-T3- --(W) 3.5 to 1 {35 to 1 } JQ()-G- - JQ()-T- - JQ-F- - 5 to.85 {.5 to 8.5} JQ()-G- --(W) JQ()-T- --(W) JQ-F- --(W) ¾.85 to 3.5 { 8.5 to 35 } JQ()-G- --(W) JQ()-T- --(W) JQ-F- --(W) 1 {1} 3.5 to 1 {35 to 1 } JQ()-G1- - JQ()-T1- - JQ-F1- - 5 to.85 {.5 to 8.5} JQ()-G1- --(W) JQ()-T1- --(W) JQ-F1- --(W) 1¼.85 to 3.5 { 8.5 to 35 } JQ()-G1- --(W) JQ()-T1- --(W) JQ-F1- --(W) 3.5 to 1 {35 to 1 } JQ-F1- -1 1.75 to 7 {17.5 to 7 } JQ-F1- -1 3.5 to 1 {35 to 1 } Maximum flow rate L/min 5 8 5 Model code Pressure change MPa {kgf/cm } per handle revolution Model code Pressure change MPa {kgf/cm } per handle revolution JQ()- 3-.7 {.7}/revolution JQ()- 1-.7 {.7}/revolution JQ()- 3-.3 { 3 }/revolution JQ()- 1-7 {.7}/revolution JQ()- 3-.7 {7 }/revolution JQ()- 1-1.1 {11 }/revolution JQ()- -.7 {.7}/revolution JQ-F1-.8 { 8.}/revolution JQ()- -.3 { 3 }/revolution JQ-F1-1.8 { 1.8}/revolution JQ()- -.1 {1 }/revolution -
efore using the product, please check the Mass (kg) Model No. (1) () (3) Model No. (1) () (3) Model No. () (3) JQ()-G3 3.5 3.8.3 JQ()-T3.9 3.1 3. JQ-F. 7.1 JQ()-G.5 7. JQ()-T 5 5..3 JQ-F1 3.5 15. JQ()-G1 11.5.8 1.5 JQ()-T1 9.8 11.1.8 JQ-F1 38.8 Note: Mass (1) Single pilot type without check valve () Single pilot type with check valve (3) ouble pilot type with check valve : JIS graphic symbols for hydraulic system Model code JQ- -1 JQ- - JQ- -3 JQ- - Name Relief valve Sequence valve Sequence valve Unload valve Pilot method Internal pilot type Internal pilot type xternal pilot type xternal pilot type rain method Internal drain type xternal drain type xternal drain type Internal drain type JIS graphic symbols for hydraulic system PRSSUR ONTROL VLVS Model code JQ- -1 JQ- - JQ- -3 JQ- - Name ounterbalance valve Sequence valve with check valve Sequence valve with check valve ounterbalance valve Pilot method Internal pilot type Internal pilot type xternal pilot type xternal pilot type rain method Internal drain type xternal drain type xternal drain type Internal drain type JIS graphic symbols for hydraulic system Model code JQ- -1 -W JQ- - -W Name ounterbalance valve Sequence valve with check valve Pilot method Internal/external pilot type Internal/external pilot type rain method Internal drain type xternal drain type JIS graphic symbols for hydraulic system Sub-plate model code The sub-plate is not provided with the valve. Order it separately as required by specifying the model code given in the table below. Model code Nominal diameter onnection port diameter Mass kg JG-3M Rc ⅜ ⅜ JG-3M Rc ½ JG-M Rc ¾ ¾ JG-M8 Rc1 JG-1M Rc1¼ 1¼ JG-1M Rc1½ Refer to Page S- for the dimensions of the sub-plate. ccessories 1. 3.9.7 onnections Model No. Hexagon socket head cap bolt Quantity Tightening torque N m {kgf cm} JQ()-G3 M1 75 Gasket mount type JQ()-G M1 85 8 to 3 {8 to 3} JQ()-G1 M1 15 Flange connection type Flange (JIS 91 SS), O-ring, mounting bolts -1
efore using the product, please check the Handling The adjustment ranges are indicated using cracking s. For products with a function code of 1 or (internal drain type), connect the secondary side port directly to the tank. For products with a function code of or 3 (external drain type), connect the secondary side port directly to the tank. For products with the adjustment range code, do not change the drain/pilot setting to function code 1 (internal pilot type, internal drain type). Otherwise, chattering may occur. When connecting two or more of these valves for sequential operation, set the valve s such that there is a minimum difference of 1 MPa {1 kgf/cm } between two valves. Performance curves (viscosity: 3 mm /s {cst}) Flow rate - Pressure characteristics JQ()- 3 Q JQ()- - JQ()- 1-1 1 racking 1 racking 1 racking Pressure 1 Reseat JQ()-3- JQ()-3- racking Reseat racking JQ()-3- Reseat 1 3 5 Pressure 1 Reseat racking Reseat JQ()-- racking Reseat JQ()-- JQ() - 8 1 Pressure 1 Reseat racking Reseat JQ()-1- racking JQ()-1- Reseat 8 1 8 JQ()-1- characteristics OUT IN: heck valve passing resistance IN OUT: with the adjusting screw fully open JQ()-G3 - G3.5.3.1 JQ JQ()-T3 -.5.3.1 JQ-F1 - Pressure 1 1 1 8 racking Reseat JQ-1- racking Reseat JQ-1-1 3 5 JQ()-G - G.8 5 5.7.5 Pressure adjustment:,.3 Pressure adjustment:.1 5 1 JQ()-T JQ () - T.8 5 5.7.5 Pressure adjustment:,.3 Pressure adjustment:.1 5 1 JQ JQ-F -.8.7.5 Pressure adjustment:,.3 Pressure adjustment:.1 5 1 -
efore using the product, please check the Performance curves (viscosity: 3 mm /s {cst}) characteristics JQ()-G1 JQ()-T1 JQ-F1 JQ-F1 1..8 Pressure adjustment:, Pressure adjustment: 1 8 1..8 Pressure adjustment:, Pressure adjustment: 1 8 1..8 Pressure adjustment:, Pressure adjustment: 1 8 PRSSUR ONTROL VLVS.3.1 1 3 5 xternal dimension diagram JQ-G3 (G, G1) xternal drain port G1 only Model No. F G H J JQ()-G3 88 1.7 1. 35. 5.1 1.7 7 JQ()-G 11. 3. 7. 51. 171 5.7 8 JQ()-G1. 35 5 5 1 51 Model No. K L N P R JQ()-G3 59 1 35 89 JQ()-G 9 3 1 JQ()-G1 91 8 51 131 (primary ) φ17.5 F (secondary ) xternal pilot port G Maximum H Hexagonal flat lock nut: 13 Pressure adjusting screw Mounting face (conforming standard) JQ()-G3: ISO 5781--7-- JQ()-G: ISO 5781-8-1-- JQ()-G1: ISO 5781-1-13-- JQ-G3 (G, G1) (secondary ) (primary ) J K φ1 φ5 P R φ11 φl φn φ -3
efore using the product, please check the xternal dimension diagram JQ-T3 (T, T1) JQ-T3 (T, T1) S Model No. F G H J K L N P R S JQ()-T3 7 35 7 3.7 58 88 1 3 ⅜ 3.5 19 58 9 JQ()-T 95 7.5 87 5 73 5.7 9.5 11.5 5.5 7 ¾ 5.5 71.5 11 JQ()-T1 5 11 8.5 95 51 83.5 13.5.5 8 1¼ 5.5 3 87.5 18.5 JQ-F (F1) Hexagonal flat lock nut: 13 Pressure adjusting screw rain port () K N R Maximum S Pressure adjusting screw Hexagonal flat lock nut: 13 rain port Maximum F H 3-Rc "L" K (secondary ) P R G (primary ) N J xternal pilot port (primary ) 3-φ "G" -M "H" epth "J" L P xternal pilot port "F" Model No. F G H J K L N P R S JQ-F 119 9 5 1 1 1 73 51 9 81 5.7 JQ-F1 15 91 3 1.5 5 3 8 88.5 59.5 19.5 1.5 5 -
efore using the product, please check the Sectional structural diagram JQ-G JQ-T 1 17 1 19 11 1 3 5 7 1 1 17 PRSSUR ONTROL VLVS 8 1 9 15 1 JQ-F 1 17 Sealing part table 1 Note: The sectional structural diagram is for the adjustment range codes,, and. For products with the adjustment range code, the plunger (1) is not provided. Part specifications Part No. Name Quantity JQ-G3 JQ-G3 JQ-T3 JQ-T3 JQ-G JQ-G JQ-T JQ-T 1 O-ring JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1G3 JIS 1 1G3 JIS 1 1G3 JIS 1 1G3 17 O-ring JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P O-ring 1 JIS 1 1P11 JIS 1 1P11 JIS 1 1P11 JIS 1 1P11 JIS 1 1P1 JIS 1 1P1 JIS 1 1P1 JIS 1 1P1 19 O-ring JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P O-ring JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P 1 O-ring 1 JIS 1 1P11 JIS 1 1P11 JIS 1 1P1 JIS 1 1P1 Part specifications Part No. Name Quantity JQ-F JQ-G1 JQ-G1 JQ-T1 JQ-T1 JQ-F1 JQ-F1 1 O-ring JIS 1 1G3 JIS 1 1G JIS 1 1G JIS 1 1G JIS 1 1G JIS 1 1G JIS 1 1G 17 O-ring JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P8 O-ring 1 JIS 1 1P1 JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P JIS 1 1P3 19 O-ring JIS 1 1P JIS 1 1P O-ring JIS 1 1G35 JIS 1 1G35 1 O-ring 1 JIS 1 1P1 JIS 1 1P JIS 1 1P JIS 1 1G5 JIS 1 1P38 O-ring 1 JIS 1 1G3 JIS 1 1G JIS 1 1G -5
efore using the product, please check the Setting guide The products are supplied with a function code of as standard. If a product with a function code of 1, 3 or is required, change the setting by referring to the guide given below. Gasket mount type (JQ()-G ) hanging the external drain type to the internal drain type hanging the internal pilot type to the external pilot type xternal drain port xternal pilot port ottom lid ottom lid (1) Remove the top lid. () Move the O-ring at to. (3) Fit the top lid while aligning holes and, and and. (1) Remove the bottom lid. () Move the O-ring at to. (3) Fit the bottom lid while aligning holes and, and and. Screw connecting type (JQ()-T ), flange mount type (JQ()-F ) hanging the external drain type to the internal drain type hanging the internal pilot type to the external pilot type Tapered plug rain port xternal pilot port ottom lid ottom lid Hexagon socket plug ottom lid (1) Remove the top lid. () Fit the top lid while aligning holes and. (3) Remove the tapered plug and fit the hexagon socket plug (R¼). (1) Remove the bottom lid. () Fit the bottom lid while aligning hole with hole or. (When aligning hole with hole, fit an O-ring at.) (3) Remove the hexagon socket plug on the external pilot port. -