Hi-lume LED Overview Hi-lume LED 1 12.11.9 Hi-lume LED is a high-performance, constant current driver that provides energy-efficient dimming for LED lighting. With industry-leading full-range % to 1% dimming, Hi-lume LED provides the ideal functionality for any lighting application. Features Continuous, flicker-free dimming from % to 1%. Standard 3-wire line-voltage phase-control technology for consistent dimming performance and compatibility with all Lutron 3-wire fluorescent dimmers. EcoSystem Bus control, compatible with all Lutron EcoSystem, GRAFIK Eye QSE and Quantum systems. Turns on to any dimmed level without flashing to full brightness. Low harmonic distortion throughout the entire dimming range maintains power quality. Protected from miswires of any input power to control lead, or from lamp leads to each other and/or ground. A rated lifetime of 5, hours. Instant light output at any level when turned on. UL recognized - for United States and Canada. For approved fixtures please go to: www.lutron.com/hilumeled/fixtures Hi-lume LED, case type A 3. in (76 mm) W x 1. in (25 mm) H x 4.9 in (124 mm) L
Specifications Performance Dimming Range: % to 1% measured relative light output (RLO) Relative Humidity: maximum 9% non-condensing Operating : 1/ at 5/6 Hz Power Factor: greater than.9 at 25 W Total Harmonic Distortion (THD): less than % at 25 W Inrush < 2 A Sound Rating: Inaudible in a 24 db ambient A rated lifetime of 5, hours - maximum case temperature: 73 ºC Hi-lume LED 2 12.11.9 Standards Class P thermally protected Meets FCC Part Non-Consumer requirements for EMI/RFI emissions in a typical grounded fixture Manufacturing facilities employ ESD reduction practices that comply with the requirements of ANSI/ESD S. Lutron Quality Systems registered to ISO 91. UL 875 recognized cul recognized for use in Canada Class 2 output Driver Wiring & Mounting Driver is grounded by a mounting screw or by terminal connection to the grounded fixture Terminal blocks on the driver accept one 18 AWG or 16 AWG solid wire per terminal Fixture must be grounded in accordance with local and national electrical codes
.7 Amp Driver L3D257AUNV1S* Hi-lume LED 3 12.11.9 Electrical Ratings (Typical)** Model Input Frequency Power L3D257AUNV1S 1/.27/.13 A 5/6 Hz -36 V.7 A + 5% 7-25 W Yes Class 2 vs. Power Factor vs. Power 36 34 1..9 32 (volts) 3 28 26 24 22 18 16 14 Power Factor Power Factor.8.7.6.5.4.3.2 12.1.1.2.3.4.5.6.7.8.9 1 (Amps). 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 25 THD vs. Power 3 Efficiency vs. Power 9 25 8 THD (%) Efficiency (%) 7 6 5 4 3 5 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 25 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 25 * The S at the end of the ballast number indicates a studded option. Remove the S for a non-studded driver. ** At full light output.
1.5 Amp Driver L3D255AUNV1S* Hi-lume LED 4 12.11.9 Electrical Ratings (Typical)** Model Input Frequency Power L3D255AUNV1S 1/.27/.13 A 5/6 Hz 7-24 V 1.5 A + 5% 7-25 W Yes Class 2 vs. 24 Power Factor vs. Power 1. 23 22.9 (volts) 21 19 18 17 16 14 13 12 11 Power Factor.8.7.6.5.4.3.2 9.1 8 7..2.4.6.8 1. 1.2 (Amps). 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 25 THD vs. Power 3 Efficiency vs. Power 25 9 8 7 THD (%) Efficiency (%) 6 5 4 3 5 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 25 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 25 * The S at the end of the ballast number indicates a studded option. Remove the S for a non-studded driver. ** At full light output.
1.4 Amp Driver L3D2514AUNV1S* Hi-lume LED 5 12.11.9 Electrical Ratings (Typical)** Model Input Frequency Power L3D2514AUNV1S 1/.27/.13 A 5/6 Hz 7-18 V 1.4 A + 5% -25 W Yes Class 2 vs. 18 Power Factor vs. Power 1. 17.9 (volts) 16 14 13 12 11 9 Power Factor.8.7.6.5.4.3.2 8.1 7..2.4.6.8 1. 1.2 1.4 1.6 (Amps). 11 12 13 14 16 17 18 19 21 22 23 24 25 THD vs. Power 3 Efficiency vs. Power 9 25 8 7 THD (%) Efficiency (%) 6 5 4 3 5 11 12 13 14 16 17 18 19 21 22 23 24 25 11 12 13 14 16 17 18 19 21 22 23 24 25 * The S at the end of the ballast number indicates a studded option. Remove the S for a non-studded driver. ** At full light output.
2. Amp Driver L3D252AUNV1S* Hi-lume LED 6 12.11.9 Electrical Ratings (Typical)** Model Input Frequency Power L3D252AUNV1S 1/.27/.13 A 5/6 Hz 7-12 V 2. A + 5% -25 W Yes Class 2 vs. Power Factor vs. Power 12 1 11.5.9 (volts) 11.5 9.5 9 8.5 8 Power Factor.8.7.6.5.4.3.2 7.5.1 7.5 1 1.5 2 2.5 3 (Amps) 16 17 18 19 21 22 23 24 25 THD vs. Power 3 Efficiency vs. Power 9 25 8 THD (%) Efficiency (%) 7 6 5 4 3 5 16 17 18 19 21 22 23 24 25 16 17 18 19 21 22 23 24 25 * The S at the end of the ballast number indicates a studded option. Remove the S for a non-studded driver. ** At full light output.
Case Dimensions A G F B I H E 8-32 Threaded Stud.29 in (.736 mm) D C * A B C D E F G H I 4. in (7 mm) 1. in (25 mm) 3. in (76 mm) 4.9 in (124 mm) 4.6 in (117 mm) (mounting centers) 2. in (51 mm) 1.8 in (27 mm) 1.6 in (41 mm) 1.39 in (35 mm) Hi-lume LED 7 12.11.9 * The S at the end of the ballast model number indicates a studded option. Remove the S for a non-studded driver. Wiring Diagram for 3-Wire Dimming Switched Hot +V To Dimming Control Dimmed Hot Neutral Hi-lume LED Ground ** -V LED light engine Ground Wiring Diagram for EcoSystem Digital Control Hot +V To Line Neutral Hi-lume LED Ground Ground ** -V LED light engine E1 To EcoSystem Bus E2 ** Fixture must be grounded in accordance with local and national electrical codes. Maximum lamp-to-driver wire length is 3 ft (1 m).
Hi-lume LED 3-Wire LED Dimmer Wiring Diagram Hi-lume LED can be controlled with Lutron fluorescent analog controls, including: Ariadni Diva Lyneo LXTM Maestro 3-wire control wiring Hi-lume LED 8 12.11.9 Make sure that the supply breaker to Hi-lume LED Driver and dimmer is OFF when wiring. Wire as shown Line input: Hot Neutral Connects to: Dimmer Black Wire Dimmer White Wire GRAFIK Eye Nova GRAFIK Eye QS Nova T GRAFIK 5TM Skylark GRAFIK 6 Vareo GRAFIK 7TM Vierti Dimmer wire: Yellow Red White Green Connects to: Driver Orange (DH) Driver Black (HOT) Driver White (NEU) Earth Ground and Driver Ground Hi-lume LED driver terminals accept one 18 AWG or 16 AWG solid wire per terminal. 3-Wire Dimmer Red -V +V NC HOT DH NEU GND E1 E2 Green Yellow LUTRON Ground* Hot / Black Ground* Neutral / White Green White Orange Black -V +V NC HOT DH NEU GND E1 E2 Ground* * Fixture must be grounded in accordance with local and national electrical codes.
Hi-lume LED EcoSystem Wiring Diagram Driver Terminals Hi-lume LED 9 12.11.9 Hi-lume LED can be controlled digitally as part of an EcoSystem, GRAFIK Eye QSE and/or Quantum system. Within these systems it is addressed and configured over the EcoSystem bus wiring (E1 and E2). Connect the two conductors to the two Digital Driver terminals E1 and E2 as shown. Sensors cannot directly connect to the Hi-lume LED driver. The Hi-lume LED driver can integrate with sensors when connected to EcoSystem ballasts and EcoSystem power modules. Make sure that the supply breaker to the Hi-lume LED Driver and EcoSystem Bus Supply is OFF when wiring. E1 and E2 (EcoSystem bus wires) are polarity insensitive and can be wired in any topology. An EcoSystem Bus Supply provides power for the EcoSystem bus and supports system programming. The EcoSystem bus may be wired Class 1 or Class 2. Consult applicable electrical codes for proper wiring practices. Note: EcoSystem Bus length is limited by the wire gauge used for E1 and E2 as follows: Wire Gauge Bus Length (max) 12 AWG 2 ft (67 m) 14 AWG 14 ft (427 m) 16 AWG 9 ft (274 m) -V +V NC -V +V NC Ground * Ground * HOT DH NEU GND E1 E2 Driver Terminals HOT DH NEU GND E1 E2 To the EcoSystem Bus Supply and up to 64 total drivers or ballasts E2 E1 Hot Neutral Lighting circuit fed from distribution or switch panel The Hi-lume LED driver terminals and EcoSystem Bus terminals accept one 18 AWG or 16 AWG solid wire per terminal. * Fixture must be grounded in accordance with local and national electrical codes.
Hi-lume LED 12.11.9 Attention Electricians and Contractors ATTENTION FACILITIES MANAGERS Driver Leads Lead lengths from driver to LED light engine must not exceed 3 ft (1 m). Driver Operating Temperature Driver case temperature must not exceed 73 C at any point. Wiring and Grounding Driver and lighting fixture must be grounded. Drivers must be installed per national and local electrical codes. SERVICE Replacement Parts Use replacement parts with exact Lutron model numbers. Consult Lutron if you have any questions. Further Information For further information, please visit us at www.lutron.com/hilumeled or contact our 24-hour Technical Support Center at 1-8-523-9466.