I. SCOPE The supply of Water Tanker Trucks (Brand New), LHD, Suitable for Use in extreme climatic and physical conditions in Iraq. LOT 1 WATER TRUCKS 1 II. TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS OF 8,000 LITERS WATER TANKER Note: Pictures are for reference purpose only and may contain optional accessories. NO SPECIFICATIONS QTY 1. CHASSIS VEHICLE 3 Units Brand / Model any Brand meet the technical requirements, zero kilometer Engine Not less than 200 hp, diesel, six cylinder, Euro 2 or higher Drive Train 6x4 or 4x4 or 4x2 Steering LHD Cabin Single, A/C 2. GENERAL General 3. WATER TANK Baffle Plates Tank Filling Overflow / Drainage Level Indicator Water tanker made of stainless steel material suitable for transport of drinking water. All piping and fittings of galvanized steel pipes. On top of the tank there will be a walkway lying on both sides and walkway. Access to walkway will be provided by a steel ladder mounted on the tank. 8,000 Liters Elliptical tank 3 partition manufactured from AISI 304 Stainless Steel Min. 3 units vertical and horizontal baffle plates 2 units 2.5 filling inlets with couplings and non-return valves on both sides of the tank and through the manhole having at least 450 mm diameter with lid mounted on top of the tank. Bluff pipe for air and extra water inside the tank A transparent (rubber) water level indicator will be mounted on the side of the tank. 1
4. WATER PUMP Moto Pump 1000 lpm Outlets 1 unit 2 or 3 Driven PTO/Gasoline/Diesel Engine Location On one side of the tank or Under the tank Suction 1 unit 2 or 3 5. HOSE REEL Material Placement Hose Rewinding 6. PAINTING Tank Exterior 7. ACCESSORIES Light Alloy On the rear side of the vehicle 1 unit 1 20 meter Manual White 3 units 4 3 meter suction pipe 2 units 2 20 meter water delivery hose Hose lockers on both sides Suction Wrenches 1 ladder providing access to the top of the tank mounted Toolbox 8. DOCUMENTS 1 set of Workshop Manual, Spare Parts Catalogue, Operation & Maintenance Booklet in English 9. WARRANTY Minimum a 1-one-year warranty against any kind of laboring mistakes 10. SPARE PARTS Spare parts guarantee for 10-ten-years operation period. 11. INSPECTION & TRAINING 12. Fast Moving Spares for 50,000 kms Factory Acceptance Tests and Training to be provided in Dohuk, Iraq Fast moving spares for 50,000 kms to be included with a separate cost. every set should include. 1. oil Filter 2. fuel filter 3. Air filter. The items should be Origin from the proposed brand. 3 Sets 2
Note: Please indicate the spares in the package. 13. Spare tire one spare tire installed with the truck (Size according to type of Brand) 3 Units 2 TECHNICAL SPECIFICATIONS OF 10,000 LITERS WATER TANKER Note: Pictures are for reference purpose only and may contain optional accessories. NO SPECIFICATIONS QTY 1 CHASSIS VEHICLE 2 Units Brand / Model Engine Drive Train Steering Cabin any Brand meet the technical requirements, zero kilometer Not less than 240 hp, diesel, six cylinder, Euro 2 or higher 6x4 or 4x4 LHD Single, A/C 2 GENERAL General Water tanker made of stainless steel material suitable for transport of drinking water. All piping and fittings of galvanized steel pipes. On top of the tank there will be a walkway lying on both sides and walkway. Access to walkway will be provided by a steel ladder mounted on the tank. 3 WATER TANK 10,000 Liters ± 5% Elliptical tank 3 partition manufactured from AISI 304 Stainless Steel Baffle Plates Min. 3 units vertical and horizontal baffle plates Tank Filling 2 units 2.5 filling inlets with couplings and non-return valves on both sides of the tank and through the manhole having at least 450 mm diameter with lid mounted on top of the tank. 3
Overflow / Drainage Level Indicator Bluff pipe for air and extra water inside the tank A transparent (rubber) water level indicator will be mounted on the side of the tank. 4 WATER PUMP Moto Pump 1000 lpm Outlets 1 unit 2 or 3 Driven PTO/Gasoline/Diesel Engine Location On one side of the tank or Under the tank Suction 1 unit 2 or 3 5 HOSE REEL Material Placement Hose Rewinding 6 PAINTING Tank Exterior 7 ACCESSORIES Light Alloy On the rear side of the vehicle 1 unit 1 20 meter Manual White 3 units 4 3 meter suction pipe 2 units 2 20 meter water delivery hose Hose lockers on both sides Suction Wrenches 1 ladder providing access to the top of the tank mounted Toolbox 8 DOCUMENTS 1 set of Workshop Manual, Spare Parts Catalogue, Operation & Maintenance Booklet in English 9 WARRANTY Minimum a 1-one-year warranty against any kind of laboring mistakes 10 SPARE PARTS Spare parts guarantee for 10-ten-years operation period. 11 INSPECTION & TRAINING 12 Fast Moving Spares for 50,000 kms Factory Acceptance Tests and Training to be provided in Dohuk, Iraq Fast moving spares for 50,000 kms to be included with a separate cost. every set should include. 1. oil Filter 2. fuel filter 3. Air filter. 2 Sets 4
The items should be Origin from the proposed brand. Note: Please indicate the spares in the package. 13 Spare tire one spare tire installed with the truck (Size according to type of Brand) 2 Units LOT 2 SEWAGE TRUCKS 1 TECHNICAL SPECIFICATIONS OF 10,000 LITERS VACUUM/SEWAGE TRUCK (for extracting and disposing sewage from in underground tanks) Note: Pictures are for reference purpose only and may contain optional accessories. QTY SPECIFICATIONS NO 1. CHASSIS VEHICLE 3 Units Brand Engine Drive Train Steering Cabin 2. TANK General any Brand meet the technical requirements, zero kilometer Not less than 240 hp, diesel, six cylinder, Euro 2 or higher 6x4 or 4x4 LHD Single, A/C The tank superstructure will be mounted on an auxiliary chassis manufactured from 8mm St.52 carbon steel, with flexible connections to avoid torsion Cylindrical shaped, reinforced tank resistant to vacuum and pressure. 10,000 liters ± 5% Material 6mm St.52 Carbon Steel Manhole Min. 450 mm with aluminum cap on clean water compartment Tank-Chassis Connection Tank Discharge The tank will be connected to the vehicle s chassis with an auxiliary chassis. The auxiliary chassis will be made of 8 mm St-52 steel material. Tank is placed on chassis at 3% slope. Easy discharge when rear lid is open. 5
Suction Valve for sewage Discharge Valve for sewage Level Gauges Sludge Chute 3. REAR LID Rear Lid Material Rear Lid Opening Rear Lid Lock 4. VACUUM PUMP Vacuum Pump Driven Max. Vacuum Power Req. at max. Pressure Power Req. at max. Vacuum Manual controlled, 4 gate type valve and top mounted telescopic suction boom Pneumatic controlled, 6 gate type valve 3 units of dish shaped transparent level gauges on the rear lid for sewage A sludge chute at the rear to prevent depositing sludge underneath the vehicle. The chute will have side wings to prevent sludge dispersion sideways. 8mm St.52 Carbon Steel Hinged from the upper side of the tank. Hydraulic controlled vertical opening 4 units of hydraulic controlled locks 660 m3/h By PTO or Split Shaft Pto %95 30 kw 20 kw 5. SAFETY 1. Safety System Stainless steel ball located on the top of the tank 2. Safety System Safety ball between the vacuum pump and the first safety system which is mounted on the vacuum installation, volume tank and discharge valve Relief Valves Will be used where necessary System Safety Control panel has an emergency stop buttons. Once it is activated, the equipment can be restarted from the driver s cabin only. 6. ACCESSORIES 1 unit 1m steel end pipe for suction arm 2 units 4 x 2m suction hose 1-unit manhole lifting winch mounted on rear lid 1 unit ½ inch spray gun 2 units of aluminum lockable storage compartments one on each side of the truck 1-unit steel tool box Mudguards for rear wheels with mud flaps ladder 7. PAINTING white 8. DOCUMENTS 1 set of Maintenance and Operation Booklet 6
in English 9. WARRANTY Minimum a 1-one-year warranty against any kind of laboring mistakes 10. SPARE PARTS Spare parts guarantee for 10-ten-years operation period. 11. INSPECTION & TRAINING 12. Fast Moving Spares for 50,000 kms Factory Acceptance Tests and Training to be provided in Dohuk, Iraq Fast moving spares for 50,000 kms to be included with a separate cost. every set should include. 1. oil Filter 2. fuel filter 3. Air filter. The items should be Origin from the proposed brand. 3 Sets Note: Please indicate the spares in the package. 13. Spare tire one spare tire installed with the truck (Size according to type of Brand) 3 Units 2 TECHNICAL SPECIFICATIONS OF 17,000 LITERS VACUUM/SEWAGE TRUCK (for extracting and disposing sewage from in underground tanks) Note: Pictures are for reference purpose only and may contain optional accessories. QTY SPECIFICATIONS NO 1 CHASSIS VEHICLE 1 Units Brand Engine Drive Train Steering Cabin 2 TANK General any Brand meet the technical requirements, zero kilometer Not less than 250 hp, diesel, six cylinder, Euro 2 or higher 6x4 LHD Single, A/C The tank superstructure will be mounted on an auxiliary chassis manufactured from 8mm St.52 carbon steel, with flexible connections to avoid torsion 7
Cylindrical shaped, reinforced tank resistant to vacuum and pressure. 17,000 liters ± 10% Material 6mm St.52 Carbon Steel Manhole Min. 450 mm with aluminum cap on clean Tank-Chassis Connection Tank Discharge Suction Valve for sewage Discharge Valve for sewage Level Gauges Sludge Chute water compartment The tank will be connected to the vehicle s chassis with an auxiliary chassis. The auxiliary chassis will be made of 8 mm St-52 steel material. Tank is placed on chassis at 3% slope. Easy discharge when rear lid is open. Manual controlled, 4 gate type valve and top mounted telescopic suction boom Pneumatic controlled, 6 gate type valve 3 units of dish shaped transparent level gauges on the rear lid for sewage A sludge chute at the rear to prevent depositing sludge underneath the vehicle. The chute will have side wings to prevent sludge dispersion sideways. 3 REAR LID Rear Lid Material Rear Lid Opening Rear Lid Lock 4 VACUUM PUMP Vacuum Pump Driven Max. Vacuum Power Req. at max. Pressure Power Req. at max. Vacuum 8mm St.52 Carbon Steel Hinged from the upper side of the tank. Hydraulic controlled vertical opening 4 units of hydraulic controlled locks 660 m3/h By PTO or Split Shaft Pto %95 30 kw 20 kw 5 SAFETY 1. Safety System Stainless steel ball located on the top of the tank 2. Safety System Safety ball between the vacuum pump and the first safety system which is mounted on the vacuum installation, volume tank and discharge valve Relief Valves Will be used where necessary System Safety Control panel has an emergency stop buttons. Once it is activated, the equipment can be restarted from the driver s cabin only. 6 ACCESSORIES 1 unit 1m steel end pipe for suction arm 2 units 4 x 2m suction hose 1-unit manhole lifting winch mounted on 8
7 PAINTING white rear lid 1 unit ½ inch spray gun 2 units of aluminum lockable storage compartments one on each side of the truck 1-unit steel tool box Mudguards for rear wheels with mud flaps ladder 8 DOCUMENTS 1 set of Maintenance and Operation Booklet in English 9 WARRANTY Minimum a 1-one-year warranty against any kind of laboring mistakes 10 SPARE PARTS Spare parts guarantee for 10-ten-years operation period. 11 INSPECTION & TRAINING 12 Fast Moving Spares for 50,000 kms Factory Acceptance Tests and Training to be provided in Dohuk, Iraq Fast moving spares for 50,000 kms to be included with a separate cost. every set should include. 1. oil Filter 2. fuel filter 3. Air filter. The items should be Origin from the proposed brand. 1 Sets Note: Please indicate the spares in the package. 13 Spare tire one spare tire installed with the truck (Size according to type of Brand) 1 Units 9