Operatr s Manual with Maintenance Infrmatin First Editin Tenth Printing Part N. 48735
SELF-PROPELLED SCISSOR LIFTS GS TM -2668 RT & GS TM -3268 RT Specificatins MODELS GS TM -2668 RT GS TM -3268 RT MEASUREMENTS Metric US Metric US C Wrking height maximum* 9.92 m 32 ft 11.75 m 38 ft A B Platfrm height maximum Platfrm height - stwed 7.92 m 1.19 m 26 ft 3 ft 10.75 in 9.75 m 1.31 m 32 ft 4 ft 3.75 in C Platfrm length - utside 2.51 m 8 ft 3 in 2.51 m 8 ft 3 in - extended 2.96 m 9 ft 9 in 2.96 m 9 ft 9 in Slide-ut platfrm extensin deck 1.10 m 3 ft 6 in 1.10 m 3 ft 6 in D Platfrm width - utside 1.55 m 5 ft 1 in 1.55 m 5 ft 1 in Tebard height 15 cm 6 in 15 cm 6 in E Height - stwed** 2.32 m 7 ft 7.5 in 2.57 m 8 ft 5 in rails lwered 1.70 m 5 ft 7 in 1.83 m 6 ft F Length - stwed platfrm extended 2.67 m 3.75 m 8 ft 9 in 12 ft 4 in 2.67 m 3.75 m 8 ft 9 in 12 ft 4 in with utriggers 3.43 m 11 ft 3 in 3.43 m 11 ft 3 in G Width 1.73 m 5 ft 8 in 1.73 m 5 ft 8 in H Wheelbase 1.85 m 6 ft 1 in 1.85 m 6 ft 1 in I Grund clearance - centre 20 cm 8 in 20 cm 8 in E B D H F PRODUCTIVITY Maximum platfrm ccupancy 4/4 4/4 4/2 4/2 (indr/utdr) Lift capacity 567 kg 1,250 lbs 454 kg 1,000 lbs Drive speed - stwed 6.1 km/h 3.8 mph 6.1 km/h 3.8 mph Drive speed - raised 0.8 km/h 0.5 mph 0.8 km/h 0.5 mph Gradeability-stwed*** 35% 35% 30% 30% Maximum utrigger levelling: frnt t back 6.6º 6.6º 6.6º 6.6º side t side 10.6º 10.6º 10.6º 10.6º Turning radius - inside 1.52 m 5 ft 1.52 m 5 ft Turning radius - utside 3.68 m 12 ft 1 in 3.68 m 12 ft 1 in Raise/lwer speed 30/35 sec 30/35 sec 40/37 sec 40/37 sec Cntrls prprtinal prprtinal prprtinal prprtinal Drive fur wheel fur wheel fur wheel fur wheel Tyres - rugh terrain 30 x 60 cm 12 x 23.5 in 30 x 60 cm 12 x 23.5 in POWER I G Pwer surce Kubta D-1105 Diesel 24.9 hp (18.6 kw) Kubta D-1105 Diesel 24.9 hp (18.6 kw) Kubta petrl/lpg 23 hp (17 kw) Kubta petrl/lpg 23 hp (17 kw) Perkins 403D-11 Diesel 26 hp Perkins 403D-11 Diesel 26 hp Fuel tank capacity 56.8 L 15 gal 56.8 L 15 gal Hydraulic system capacity 62.5 L 16.5 gal 62.5 L 16.5 gal A WEIGHT**** 3,236 kg 7,194 lbs 3,771 kg 8,314 lbs CE max 3,798 kg 8,373 lbs 4,306 kg 9,493 lbs Weight mdifiers fr ptins: Outriggers add 483 kg 1,064 lbs 483 kg 1,064 lbs Generatr add 48 kg 105 lbs 48 kg 405 lbs Nn marking rugh terrain tyres add 323 kg 712 lbs add 323 kg 712 lbs STANDARDS COMPLIANCE CE EN280, PB-10-611-03 * The metric equivalent f wrking height adds 2 m t platfrm height. U.S. adds 6 ft t platfrm height. ** Based n RT tyres; deduct 5.8 cm (2 in) fr turf and nn-marking tyres. *** Gradeability applies t driving n slpes. Gradeability may vary depending n the weight f ptins installed n machine. See Operatr s Manual fr details regarding slpe ratings. **** Weight varies depending n ptins and cuntry standards. www.genieindustries.cm 01/09 Part N. B109350UK
SELF-PROPELLED SCISSOR LIFTS GS TM -2668 RT & GS TM -3268 RT Features STANDARD FEATURES MEASUREMENTS GS -2668RT 9.92 m (32 ft) wrking height Up t 567 kg (1,250 Ib) lift capacity GS -3268RT 11.75 m (38 ft) wrking height Up t 454 kg (1,000 lb) lift capacity PRODUCTIVITY 2.51 x 1.55 m (8 ft 3 in x 5 ft 1 in) steel frame with replaceable aluminium deck 1.22 m (4 ft) platfrm extensin deck Flding guardrails Prprtinal lift and drive Onbard diagnstic system AC pwer t platfrm Full-height swing gate 4x4 Psitive tractin cntrl Fur-wheel braking Swing-ut engine tray Fam-filled rugh terrain tyres Tilt level sensr with audible alarm Descent alarm Hrn Hur meter Certified lad sensr POWER Kubta D-1105 Diesel 24.9 hp (18.6 kw) OPTIONS & ACCESSORIES PRODUCTIVITY Autmatic levelling hydraulic utriggers Air line t platfrm Nn-marking rugh terrain tyres 30 x 60 cm (12 x 23.5 in) Dual flashing beacns Mtin alarm Platfrm wrk lights Bidegradable hydraulic il Fire resistant il POWER Kubta diesel 24.9 hp (18.6 kw) Kubta petrl/lpg 23 hp (17 kw) Perkins 403D - 11 Diesel 26 hp 2000 watt generatr (110 V/60 Hz) Cld weather packages fr all engines (nt CE) Diesel scrubber (Perkins) Hydraulic il cler LPG steel tank nly, 15 kg (33.5 lb) capacity Additinal LPG tank and carrier Distributed By: UK Millennium Huse Brunel Drive Newark NG24 2DE UK Tel: +44 (0)1476 584333 Fax: +44 (0)1476 584334 France 10, ZA de la Crix St. Mathieu 28320 Gallardn France Tel: +33 (0)2 37 26 09 99 Fax: +33 (0)2 37 26 09 98 Germany Finienweg 3 28832 Achim/Bremen Germany Tel: +49 (0)4202 8852-0 Fax: +49 (0)4202 8852-25 Spain Gai à 31, Pl. Ind. Plá d en Cll 08110 Mntcada i Reixac Barcelna Spain Tel: +34 93 572 50 90 Fax: +34 93 572 50 91 Scandinavia Imprtgatan 17 422 46 Hisings Backa Sweden Tel: +46 31 57 51 00 Fax: +46 31 57 90 20 Middle East Terex Middle East PO Bx 282325, Dubai U.A.E. Tel: +971 4 885 8030 Fax: +971 4 885 6364 Email: awp.infme@terex.cm Genie United States 18340 NE 76th Street P.O. Bx 97030 Redmnd, WA USA 98073-9730 Tel: +1 425 881-1800 Fax: +1 425 883-3475 Email: AWP-InfEurpe@terex.cm Effective date: January, 2009. Prduct specificatins and prices are subject t change withut ntice r bligatin. The phtgraphs and/r drawings in this dcument are fr illustrative purpses nly. Refer t the apprpriate Operatr s Manual fr instructins n the prper use f this equipment. Failure t fllw the apprpriate Operatr s Manual when using ur equipment r t therwise act irrespnsibly may result in serius injury r death. The nly warranty applicable t ur equipment is the standard written warranty applicable t the particular prduct and sale and we make n ther warranty, expressed r implied. Prducts and services listed may be trademarks, service marks r trade-names f Terex Crpratin, Genie Industries, Inc. and/r their subsidiaries in the U.S.A. and many ther cuntries. All rights are reserved. Terex is a Registered Trademark f Terex Crpratin in the U.S.A. and many ther cuntries. Genie is a Registered Trademark f Genie Industries, Inc in the U.S.A. and many ther cuntries. Genie is a Terex Cmpany. Cpyright 2009 Terex Crpratin 01/09 Part N. B109350UK www.genieindustries.cm
Operatr's Manual First Editin Tenth Printing Imprtant Read, understand and bey these safety rules and perating instructins befre perating this machine. Only trained and authrized persnnel shall be permitted t perate this machine. This manual shuld be cnsidered a permanent part f yur machine and shuld remain with the machine at all times. If yu have any questins, please call Genie Industries. Cntents Page Safety... 1 Legend... 7 Cntrls... 8 Pre-peratin Inspectin... 12 Maintenance... 14 Functin Tests... 17 Wrk Place Inspectin... 20 Operating Instructins... 21 Transprt Instructins... 25 Flr Lading... 26 Decals... 27 Specificatins... 29 Cntact us: Cpyright 1998 by Genie Industries First Editin: Tenth Printing, January 2004 "Genie" is a registered trademark f Genie Industries in the U.S.A. and many ther cuntries. "GS" is a trademark f Genie Industries. These machines cmply with ANSI/SIA 92.6-1999. Printed n recycled paper Printed in U.S.A. Internet: http://www.genielift.cm e-mail: techpub@genieind.cm Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual Safety Rules Danger Failure t bey the instructins and safety rules in this manual will result in death r serius injury. D Nt Operate Unless: Yu learn and practice the principles f safe machine peratin cntained in this peratr's manual. 1 Avid hazardus situatins. Knw and understand the safety rules befre ging n t the next sectin. 2 Always perfrm a pre-peratin inspectin. 3 Always perfrm functin tests prir t use. 4 Inspect the wrk place. 5 Only use the machine as it was intended. Yu read, understand and bey: Manufacturer's instructins and safety rules safety and peratr's manuals and machine decals emplyer's safety rules and wrksite regulatins applicable gvernmental regulatins Yu are prperly trained t safely perate the machine. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 1
Operatr's Manual First Editin Tenth Printing SAFETY RULES Electrcutin Hazards This machine is nt electrically insulated and will nt prvide prtectin frm cntact with r prximity t electrical current. Tip-ver Hazards Occupants and equipment shall nt exceed the maximum platfrm capacity r the maximum capacity f the platfrm extensin. Maximum capacity - GS-2668RT Platfrm retracted 1250 lbs 567 kg Platfrm extended - Platfrm nly 950 lbs 431 kg Platfrm extended - Extensin nly 300 lbs 136 kg Maximum ccupants - ANSI and CSA 4 Maintain safe distances frm electrical pwer lines and apparatus in accrdance with applicable gvernmental regulatins and the fllwing chart. Vltage Phase t Phase Minimum Safe Apprach Distance Feet Meters 0 t 300V Avid Cntact 300V t 50KV 10 3.05 50KV t 200KV 15 4.60 200KV t 350KV 20 6.10 350KV t 500KV 25 7.62 500KV t 750KV 35 10.67 750KV t 1000KV 45 13.72 Maximum ccupants - CE Outdr use 4 Indr use nly 4 1250 lbs / 567 kg Extensin nly Platfrm nly 300 lbs / 136 kg 950 lbs / 431 kg Maximum capacity - GS-3268RT Platfrm retracted 1000 lbs 454 kg Platfrm extended - Platfrm nly 700 lbs 318 kg Platfrm extended - Extensin nly 300 lbs 136 kg Maximum ccupants - ANSI and CSA 4 Maximum ccupants - CE Outdr use 2 Indr use nly 4 Allw fr platfrm mvement, electrical line sway r sag and beware f strng r gusty winds. Keep away frm the machine if it cntacts energized pwer lines. Persnnel n the grund r in the platfrm must nt tuch r perate the machine until energized pwer lines are shut ff. D nt perate the machine during lightning r strms. 1000 lbs / 454 kg Extensin nly Platfrm nly 300 lbs / 136 kg 700 lbs / 318 kg D nt use the machine as a grund fr welding. 2 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual SAFETY RULES D nt alter r disable the limit switch(s). D nt drive ver 0.5 mph (0.8 km/h) with the platfrm raised. Mdels withut utriggers: D nt raise the platfrm unless the machine is n a firm, level surface. D nt perate the machine in strng r gusty winds. D nt increase the surface area f the platfrm r the lad. Increasing the area expsed t the wind will decrease machine stability. Mdels with utriggers: D nt lwer the utriggers unless the machine is n a firm surface. Avid drp-ffs, hles, unstable r slippery surfaces and ther pssible hazardus cnditins. Mdels with utriggers: D nt raise the platfrm unless the machine is level. D nt set the machine up n a surface where it cannt be leveled using nly the utriggers. Mdels with utriggers: Use cmmn sense and planning when lwering the utriggers n a slpe. The steer end utriggers must be lwered first. D nt use the platfrm cntrls t free a platfrm that is caught, snagged r therwise prevented frm nrmal mtin by an adjacent structure. All persnnel must be remved frm the platfrm befre attempting t free the platfrm using the grund cntrls. D nt drive the machine n r near uneven terrain, unstable surfaces r ther hazardus cnditins with the platfrm raised. Use extreme care and slw speeds while driving the machine in stwed psitin acrss uneven terrain, debris, unstable r slippery surfaces and near hles and drp-ffs. D nt push ff r pull tward any bject utside f the platfrm. GS-2668 RT ANSI & CSA - 4 persn CE - Indr use nly - 4 persn CE - Outdr use - 4 persn GS-3268 RT ANSI & CSA - 4 persn CE - Indr use nly - 4 persn CE - Outdr use - 2 persn 200 lbs / 890 N 200 lbs / 890 N 90 lbs / 400 N 200 lbs / 890 N 200 lbs / 890 N 150 lbs / 667 N D nt depend n the tilt alarm as a level indicatr. The tilt alarm sunds n the chassis and in the platfrm when the machine is n a severe slpe. If tilt alarm sunds: Lwer the platfrm. Mve the machine t a firm, level surface. If the tilt alarm sunds when the platfrm is raised, use extreme cautin t lwer the platfrm. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 3
Operatr's Manual First Editin Tenth Printing SAFETY RULES D nt alter r disable machine cmpnents that in any way affect safety and stability. D nt replace items critical t machine stability with items f different weight r specificatin. D nt mdify r alter an aerial wrk platfrm. Munting attachments fr hlding tls r ther materials nt the platfrm, tebards r guard rail system can increase the weight in the platfrm and the surface area f the platfrm r the lad. D nt place r attach fixed r verhanging lads t any part f this machine. D nt tie the platfrm t adjacent structures. D nt place lads utside the platfrm perimeter. Fall Hazards Occupants shuld wear a safety belt r harness and cmply with applicable gvernmental regulatins. Attach lanyard t anchr prvided in platfrm. D nt sit, stand r climb n the platfrm guard rails. Maintain a firm fting n the platfrm flr at all times. D nt place ladders r scafflds in the platfrm r against any part f this machine. D nt use the machine n a mving r mbile surface r vehicle. Be sure all tires are in gd cnditin, castle nuts are prperly tightened and ctter pins are prperly installed. D nt use the machine as a crane. D nt push the machine r ther bjects with the platfrm. D nt climb dwn frm the platfrm when raised. Keep the platfrm flr clear f debris. Clse the entry gate befre perating. D nt perate the machine unless the guard rails are prperly installed and the entry is secured fr peratin. D nt cntact adjacent structures with the platfrm. 4 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual SAFETY RULES Cllisin Hazards Be aware f limited sight distance and blind spts when driving r perating. D nt lwer the platfrm unless the area belw is clear f persnnel and bstructins. Be aware f extended platfrm psitin when mving the machine. Machine must be n level surface r secured befre releasing brakes. It is recmmended that peratrs wear an apprved hard hat when perating the machine. Check wrk area fr verhead bstructins r ther pssible hazards. Limit travel speed accrding t cnditin f grund surface, cngestin, slpe, lcatin f persnnel and any ther factrs which may cause cllisin. Cmpnent Damage Hazards D nt use any battery r charger greater than 12V t jump-start the engine. D nt use the machine as a grund fr welding. Be aware f crushing hazard when grasping the platfrm guard rail. Observe and use clr-cded directin arrws n the platfrm cntrls and platfrm decal plate fr drive and steer functins. D nt perate a machine in the path f any crane r mving verhead machinery unless the cntrls f the crane have been lcked ut and/r precautins have been taken t prevent any ptential cllisin. N stunt driving r hrseplay while perating a machine. Be sure hydraulic shutff valves (lcated by hydraulic tank) are pen befre starting engine. Explsin and Fire Hazards D nt start the engine if yu smell r detect liquid petrleum gas (LPG), gasline, diesel fuel r ther explsive substances. D nt refuel the machine with the engine running. Refuel the machine and charge the battery nly in an pen, well-ventilated area away frm sparks, flames and lighted tbacc. D nt perate the machine in hazardus lcatins r lcatins where ptentially flammable r explsive gases r particles may be present. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 5
Operatr's Manual First Editin Tenth Printing SAFETY RULES Damaged Machine Hazards D nt use a damaged r malfunctining machine. Cnduct a thrugh pre-peratin inspectin f the machine and test all functins befre each wrk shift. Immediately tag and remve frm service a damaged r malfunctining machine. Be sure all maintenance has been perfrmed as specified in this manual and the apprpriate Genie service manual. Be sure all decals are in place and legible. Be sure the peratr s, safety and respnsibilities manuals are cmplete, legible and in the strage cntainer lcated n the platfrm. Crushing Hazards Keep hands and limbs ut f scissrs. Use cmmn sense and planning when perating the machine with the cntrller frm the grund. Maintain safe distances between the peratr, the machine and fixed bjects. Maintain a firm grasp n the platfrm rail when pulling the snap pin. D nt allw the platfrm guard rails t fall. Bdily Injury Hazard Always perate the machine in a well-ventilated area t avid carbn mnxide pisning. D nt perate the machine with a hydraulic il r air leak. An air leak r hydraulic leak can penetrate and/r burn skin. Decal Legend Genie prduct decals use symbls, clr cding and signal wrds t identify the fllwing: Safety alert symbl used t alert persnnel t ptential persnal injury hazards. Obey all safety messages that fllw this symbl t avid pssible injury r death. Red used t indicate the presence f an imminently hazardus situatin which, if nt avided, will result in death r serius injury. Orange used t indicate the presence f a ptentially hazardus situatin which, if nt avided, culd result in death r serius injury. Yellw with safety alert symbl used t indicate the presence f a ptentially hazardus situatin which, if nt avided, may cause minr r mderate injury. Yellw withut safety alert symbl used t indicate the presence f a ptentially hazardus situatin which, if nt avided, may result in prperty damage. Green used t indicate peratin r maintenance infrmatin. 6 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual Legend 1 Platfrm entry gate 2 Platfrm guard rails 3 Manual strage cntainer 4 Lanyard anchrage pint 5 Platfrm extensin lck handle 6 Platfrm cntrls 7 Platfrm extensin 8 Outrigger cntrl panel (if equipped with manual cntrl utriggers) 9 Outrigger husing (if equipped with utriggers) 10 Outrigger ftpad (if equipped with utriggers) 11 LPG tank 12 Steer tire 13 Engine side cver 14 Fuel tank 15 Nn-steer tire 16 Tilt alarm (under cver) 17 Entry ladder/transprt tie-dwn 18 Grund cntrls with manual lwering valve and LED diagnstic readut 19 Grund cntrls side cver 20 Hydraulic il level indicatr (under cver) 21 Brake release pump knb and brake release knb (hidden frm view in this picture) 22 LPG tank (ptinal) 23 Safety arm 24 GFCI utlet Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 7
Operatr's Manual First Editin Tenth Printing Cntrls Diesel mdels Gasline/LPG mdels Platfrm Cntrls (mdels withut utriggers) 1 Engine stp buttn 2 Engine start buttn 3 Glw plug buttn (Diesel mdels) 4 High idle buttn with indicatr light 5 Hrn buttn 6 Machine n incline buttn: Lw speed peratin fr inclines 7 Generatr select switch with indicatr light 8 Platfrm extend/retract enable buttn (ptin) 9 Headlight/taillight buttn (ptin) 10 Emergency Stp buttn 11 Functin enable switch 12 Prprtinal cntrl handle fr drive functins and ptinal platfrm extend/ retract functin 13 Thumb rcker switch fr steer functin 14 Errr indicatr light 15 Pwer light 16 Functin enable/high speed select buttn fr up/dwn functin 17 Functin enable/lw speed select buttn fr up/dwn functin 18 Platfrm up/dwn select switch 19 Chke buttn (Gasline/LPG mdels) 20 LPG peratin buttn with indicatr light (Gasline/LPG mdels) 8 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual CONTROLS Grund Cntrl Panel 1 20 amp circuit breaker fr system circuit 2 Fuel select switch (Gasline/LPG mdels) 3 Hur meter 4 Chke switch (Gasline/LPG mdels) Glw plug switch (ptin - Diesel mdels) 5 Vlt meter (ptin) 6 Water temperature gauge with indicatr light (ptin) 7 Engine il pressure gauge with indicatr light (ptin) 8 LED diagnstic readut 9 Emergency Stp buttn 10 Keyswitch fr platfrm/ff/grund cntrl selectin 11 High idle select tggle switch 12 Engine start tggle switch 13 Functin enable tggle switch 14 Platfrm up/dwn tggle switch 15 Platfrm extend/retract tggle switch (ptin) 16 7 amp circuit breaker fr cntrls circuit Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 9
Operatr's Manual First Editin Tenth Printing CONTROLS Outrigger Cntrl Panel (if equipped with manual cntrl utriggers) 1 Lift errr indicatr light 2 Functin enable buttn 3 Outriggers raise/lwer buttn 4 Emergency Stp buttn 10 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual CONTROLS Diesel mdels Gasline/LPG mdels Platfrm Cntrls (if equipped with aut level utriggers) 1 Engine stp buttn 2 Engine start buttn 3 Glw plug buttn (Diesel mdels) 4 High idle buttn with indicatr light 5 Outrigger and hrn buttn 6 Outrigger buttn 7 Outrigger and machine n incline buttn: Lw speed peratin fr inclines 8 Outrigger and generatr select buttn with indicatr light 9 Outrigger functin enable buttn 10 Outrigger aut level buttn 11 Emergency Stp buttn 12 Functin enable switch 13 Prprtinal cntrl handle fr drive functins and ptinal platfrm extend/retract functin 14 Thumb rcker switch fr steer functin 15 Lift errr indicatr light 16 Errr indicatr light 17 Pwer light 18 Functin enable/high speed select buttn fr up/dwn functin 19 Functin enable/lw speed select buttn fr platfrm up/dwn functin 20 Platfrm up/dwn and utrigger up/dwn tggle switch 21 Chke buttn (Gasline/LPG mdels) 22 Outrigger and LPG peratin buttn with indicatr light (Gasline/LPG mdels) Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 11
Operatr's Manual First Editin Tenth Printing Pre-peratin Inspectin Fundamentals It is the respnsibility f the peratr t perfrm a Pre-peratin Inspectin and rutine maintenance. D Nt Operate Unless: Yu learn and practice the principles f safe machine peratin cntained in this peratr's manual. 1 Avid hazardus situatins. 2 Always perfrm a pre-peratin inspectin. Knw and understand the pre-peratin inspectin befre ging n t the next sectin. 3 Always perfrm functin tests prir t use. 4 Inspect the wrk place. 5 Only use the machine as it was intended. The Pre-peratin Inspectin is a visual inspectin perfrmed by the peratr prir t each wrk shift. The inspectin is designed t discver if anything is apparently wrng with a machine befre the peratr perfrms the functin tests. The Pre-peratin inspectin als serves t determine if rutine maintenance prcedures are required. Only rutine maintenance items specified in this manual may be perfrmed by the peratr. Refer t the list n the next page and check each f the items and lcatins fr mdificatins, damage r lse r missing parts. A damaged r mdified machine must never be used. If damage r any variatin frm factry delivered cnditin is discvered, the machine must be tagged and remved frm service. Repairs t the machine may nly be made by a qualified service technician, accrding t the manufacturer's specificatins. After repairs are cmpleted, the peratr must perfrm a pre-peratin inspectin again befre ging n t the functin tests. Scheduled maintenance inspectins shall be perfrmed by qualified service technicians, accrding t the manufacturer's specificatins and the requirements listed in the respnsibilities manual. 12 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual PRE-OPERATION INSPECTION Pre-peratin Inspectin Be sure that the peratr s, safety and respnsibilities manuals are cmplete, legible and in the strage cntainer lcated in the platfrm. Be sure that all decals are legible and in place. See Decals sectin. Check fr engine il leaks and prper il level. Add il if needed. See Maintenance sectin. Check fr hydraulic il leaks and prper il level. Add il if needed. See Maintenance sectin. Check fr engine clant leaks and prper level f clant. Add clant if needed. See Maintenance sectin. Check fr battery fluid leaks and prper fluid level. Add distilled water if needed. See Maintenance sectin. Check the fllwing cmpnents r areas fr damage, mdificatins and imprperly installed r missing parts: Electrical cmpnents, wiring and electrical cables Hydraulic hses, fittings, cylinders and maniflds Fuel and hydraulic tanks Drive mtrs Wear pads Tires and wheels Engine and related cmpnents Limit switches, alarms and hrn Nuts, blts and ther fasteners Platfrm entry gate Beacn and alarms (if equipped) Brake release cmpnents Safety arm Platfrm extensin Scissr pins and retaining fasteners Platfrm cntrl jystick Generatr (if equipped) Check entire machine fr: Cracks in welds r structural cmpnents Dents r damage t machine Be sure that all structural and ther critical cmpnents are present and all assciated fasteners and pins are in place and prperly tightened Side rails are installed and snap pins and blts are fastened Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 13
Operatr's Manual First Editin Tenth Printing Maintenance Check the Engine Oil Level Observe and Obey: Only rutine maintenance items specified in this manual shall be perfrmed by the peratr. Scheduled maintenance inspectins shall be cmpleted by qualified service technicians, accrding t the manufacturer's specificatins and the requirements specified in the respnsibilities manual. Maintenance Symbls Legend The fllwing symbls have been used in this manual t help cmmunicate the intent f the instructins. When ne r mre f the symbls appear at the beginning f a maintenance prcedure, it cnveys the meaning belw. Maintaining the prper engine il level is essential t gd engine perfrmance and service life. Operating the machine with an imprper il level can damage engine cmpnents. Check the il level with the engine ff. 1 Check the il level dipstick. Result: The il level shuld be at the FULL mark n the dipstick. Add il as needed. Kubta DF-750 Engine Oil capacity (including filter) Oil viscsity requirements 3.44 quarts 3.25 liters Use ils meeting API classificatin SF (labeled SF/CC r SF/CD) fr imprved wear prtectin. Units ship with 10W-40 SG/CC Kubta D-905 Engine Oil capacity (including filter) Oil viscsity requirements 5.4 quarts 5.1 liters Engine il shuld have prperties f API classificatin CC/SE, CD/SE, CC/SF r CD/SF grades. Units ship with 10W-40 SG/CC. Indicates that tls will be required t perfrm this prcedure. Indicates that new parts will be required t perfrm this prcedure. Indicates that a cld engine is required befre perfrming this prcedure. 14 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual MAINTENANCE Check the Hydraulic Oil Level Check the Batteries Maintaining the hydraulic il at the prper level is essential t machine peratin. Imprper hydraulic il levels can damage hydraulic cmpnents. Daily checks allw the inspectr t identify changes in il level that might indicate the presence f hydraulic system prblems. Perfrm this prcedure with the platfrm in the stwed psitin and the engine ff. 1 Visually inspect the sight gauge lcated n the side f the hydraulic il tank. Result: The hydraulic il level shuld be within the tp 2 inches (5 cm) f the sight gauge. 2 Add il if necessary. D nt verfill. Hydraulic il specificatins Hydraulic il type Dexrn equivalent Tank capacity 21.5 gallns 81.4 liters Hydraulic system 25 gallns 94.6 liters (including tank) Prper battery cnditin is essential t gd engine perfrmance and peratinal safety. Imprper fluid levels r damaged cables and cnnectins can result in engine cmpnent damage and hazardus cnditins. Electrcutin hazard. Cntact with ht r live circuits may result in death r serius injury. Remve all rings, watches and ther jewelry. Bdily injury hazard. Batteries cntain acid. Avid spilling r cntacting battery acid. Neutralize battery acid spills with baking sda and water. 1 Put n prtective clthing and eye wear. 2 Be sure that the battery cable cnnectins are free f crrsin. 3 Be sure that the battery hld dwns and cable cnnectins are tight. 4 Remve the battery vent caps. 5 Check the battery acid level. If needed, replenish with distilled water t the bttm f the battery fill tube. D nt verfill. 6 Install the vent caps. Adding terminal prtectrs and a crrsin preventative sealant will help eliminate crrsin n the battery terminals and cables. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 15
Operatr's Manual First Editin Tenth Printing MAINTENANCE Check the Engine Clant Level Maintaining the engine clant at the prper level is essential t engine service life. Imprper clant level will affect the engine's cling capability and damage engine cmpnents. Daily checks will allw the inspectr t identify changes in clant level that might indicate cling system prblems. 1 Check the fluid level in the clant recvery tank. Add fluid as needed. Result: The fluid level shuld be in the NORMAL range. Bdily injury hazard. Fluids in the radiatr are under pressure and extremely ht. Use cautin when remving cap and adding fluids. The Schedule There are five types f maintenance inspectins that must be perfrmed accrding t a schedule daily, quarterly, six mnths, annual, tw year. T accunt fr repeated prcedures, the Scheduled Maintenance Prcedures Sectin and the Maintenance Inspectin Reprt have been divided int five subsectins A, B, C, D and E. Use the fllwing chart t determine which grup(s) f prcedures are required t perfrm a scheduled inspectin. Inspectin Daily r every 8 hurs Quarterly r every 250 hurs Six mnths r every 500 hurs Annual r every 1000 hurs Tw year r every 2000 hurs Table r Checklist A A + B A + B + C A + B + C + D A + B + C + D + E Maintenance Inspectin Reprt Scheduled Maintenance The scheduled maintenance items must be cmpleted by a persn trained and qualified t perfrm maintenance n this machine accrding t the prcedures fund in the service manual fr this machine. Inspectins and maintenance described belw require the qualified entity t recrd and retain recrds f all inspectins and maintenance items fr fur years. Machines that have been ut f service fr mre than three mnths must receive the quarterly inspectin befre placing the machine back int service. The maintenance inspectin reprt cntains checklists fr each type f scheduled inspectin. Make cpies f the Maintenance Inspectin Reprt t use fr each inspectin. Stre cmpleted frms fr three years. 16 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual Functin Tests D Nt Operate Unless: Yu learn and practice the principles f safe machine peratin cntained in this peratr's manual. 1 Avid hazardus situatins. 2 Always perfrm a pre-peratin inspectin. 3 Always perfrm functin tests prir t use. Knw and understand the functin tests befre ging n t the next sectin. 4 Inspect the wrk place. 5 Only use the machine as it was intended. Fundamentals The Functin Tests are designed t discver any malfunctins befre the machine is put int service. The peratr must fllw the step-by-step instructins t test all machine functins. A malfunctining machine must never be used. If malfunctins are discvered, the machine must be tagged and remved frm service. Repairs t the machine may nly be made by a qualified service technician, accrding t the manufacturer's specificatins. 1 Select a test area that is firm, level and free f bstructin. At the Grund Cntrls 2 Pull ut the platfrm and grund red Emergency Stp buttn t the ON psitin. 3 Turn the key switch t grund cntrl. 4 Observe the diagnstic LED readut. Result: LED shuld lk like picture at right. 5 Start the engine. See Operating Instructins sectin. Test Emergency Stp 6 Push in the grund red Emergency Stp buttn t the OFF psitin. Result: The engine shuld turn ff and n functins shuld perate. 7 Pull ut the red Emergency Stp buttn t the ON psitin and restart the engine. Test the Up/Dwn Functins The audible warnings n this machine and the standard hrn all cme frm the same central alarm. The hrn is a cnstant tne. The descent alarm sunds at 60 beeps per minute. The alarm that ges ff when the machine is nt level sunds at 180 beeps per minute. 8 D nt hld the functin enable switch t either side and activate the platfrm up functin. Result: N functin shuld perate. After repairs are cmpleted, the peratr must perfrm a pre-peratin inspectin and functin tests again befre putting the machine int service. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 17
Operatr's Manual First Editin Tenth Printing FUNCTION TESTS 9 Hld the functin enable switch t either side and activate the platfrm up functin. Result: The platfrm shuld raise. 10 Hld the functin enable switch t either side and activate the platfrm dwn functin. Result: The platfrm shuld lwer. The descent alarm shuld sund while the platfrm is lwering. Test the Manual Lwering 11 Hld the functin enable switch t either side and activate the platfrm up functin and raise the platfrm apprximately 2 feet (0.6 m). 12 Pull the manual lwering knb r push the manual lwering buttn lcated next t the grund cntrls. Result: The platfrm shuld lwer. The descent alarm will nt sund. 13 Turn the keyswitch t platfrm cntrl. At the Platfrm Cntrls Test Emergency Stp 14 Push in the platfrm red Emergency Stp buttn t the OFF psitin. Result: N functins shuld perate. 15 Pull the red Emergency Stp buttn ut t the ON psitin. Result: The green pwer light shuld cme n. Test the Hrn 16 Push the hrn buttn. Result: The hrn shuld sund. Test the Up/Dwn Functins and the Functin Enable Switches 17 Start the engine. 18 Activate the platfrm up functin. Result: The platfrm shuld nt raise. 19 Push and hld a functin enable/speed select buttn. 20 Activate the platfrm up functin. Result: The platfrm shuld raise. 21 Release the functin enable buttn. Result: The platfrm shuld stp raising. 22 Push and hld a functin enable/speed select buttn. Activate the platfrm dwn functin. Result: The platfrm shuld lwer. The descent alarm shuld sund while the platfrm is lwering. Test the Steering Nte: When perfrming the steer and drive functin tests, stand in the platfrm facing the steer end f the machine. 23 Press and hld the functin enable switch. 24 Depress the thumb rcker switch n tp f the cntrl handle in the directin identified by the blue triangle n the cntrl panel. Result: The steer wheels shuld turn in the directin that the blue triangle pints n the cntrl panel. 18 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual FUNCTION TESTS 25 Depress the thumb rcker switch in the directin identified by the yellw triangle n cntrl panel. Result: The steer wheels shuld turn in the directin that the yellw triangle pints n the cntrl panel. Test Drive and Braking 26 Press and hld the functin enable switch. 27 Slwly mve the cntrl handle in directin indicated by the blue arrw n the cntrl panel until the machine begins t mve, then return the handle t the center psitin. Result: The machine shuld mve in the directin that the blue arrw pints n the cntrl panel, then cme t an abrupt stp. 28 Press and hld the functin enable switch. 29 Slwly mve the cntrl handle in the directin indicated by the yellw arrw n the cntrl panel until the machine begins t mve, then return the handle t the center psitin. Result: The machine shuld mve in the directin that the yellw arrw pints n the cntrl panel, then cme t an abrupt stp. Nte: The drive brakes must be able t hld the machine n any slpe it is able t climb. Test Limited Drive Speed 30 Mve and hld a functin enable/speed select switch. Raise the platfrm apprximately 6 feet (1.83 m) frm the grund. 31 Press and hld the functin enable switch. 32 Slwly mve the cntrl handle t the full drive psitin. Result: The maximum achievable drive speed with the platfrm raised shuld nt exceed 0.73 feet per secnd (0.22 meters per secnd). If the drive speed with the platfrm raised exceeds 0.73 feet per secnd (0.22 meters per secnd), immediately tag and remve the machine frm service. Test Platfrm Extensin Limit Switch (if equipped) Nte: Sme GS-2668 machines d nt have a platfrm extensin limit switch. Check under the extensin end f the platfrm t lcate this switch. This test is nt necessary n machines that are nt equipped with this limit switch. 33 Mve and hld a functin enable/speed select switch. Raise the platfrm t full height. 34 Extend the platfrm extensin. 35 Press and hld the functin enable switch. 36 Slwly mve the cntrl handle t the full drive psitin. Result: The drive functin shuld nt perate. Lwer the platfrm r retract the platfrm extensin t drive. Test the Tilt Sensr Operatin Nte: Perfrm this test frm the grund with the platfrm cntrller. D nt stand in the platfrm. 37 Fully lwer the platfrm. 38 Drive bth wheels n ne side nt a 4 inch (10 cm) blck r nt a curb. 39 Raise the platfrm. Result - ANSI and CSA mdels: The tilt alarm will sund at 180 beeps per minute. Result - CE mdels: The drive functin and the lift functin will nt perate and the tilt alarm will sund at 180 beeps per minute. 40 Lwer the platfrm and drive the machine ff the blck. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 19
Operatr's Manual First Editin Tenth Printing Wrk Place Inspectin Wrk Place Inspectin Be aware f and avid the fllwing hazardus situatins: drp-ffs r hles D Nt Operate Unless: Yu learn and practice the principles f safe machine peratin cntained in this peratr's manual. 1 Avid hazardus situatins. 2 Always perfrm a pre-peratin inspectin. 3 Always perfrm functin tests prir t use. 4 Inspect the wrk place. Knw and understand the wrk place inspectin befre ging n t the next sectin. 5 Only use the machine as it was intended. bumps, flr bstructins r debris verhead bstructins and high vltage cnductrs hazardus lcatins inadequate surface supprt t withstand all lad frces impsed by the machine wind and weather cnditins the presence f unauthrized persnnel ther pssible unsafe cnditins Fundamentals The Wrk Place Inspectin helps the peratr determine if the wrk place is suitable fr safe machine peratin. It shuld be perfrmed by the peratr prir t mving the machine t the wrk place. It is the peratr's respnsibility t read and remember the wrk place hazards, then watch fr and avid them while mving, setting up and perating the machine. 20 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual Operating Instructins Fundamentals The Operating Instructins sectin prvides instructins fr each aspect f machine peratin. It is the peratr's respnsibility t fllw all the safety rules and instructins in the peratr's, safety and respnsibilities manuals. D Nt Operate Unless: Yu learn and practice the principles f safe machine peratin cntained in this peratr's manual. 1 Avid hazardus situatins. 2 Always perfrm a pre-peratin inspectin. 3 Always perfrm functin tests prir t use. 4 Inspect the wrk place. 5 Only use the machine as it was intended. Using the machine fr anything ther than lifting persnnel and tls t an aerial wrk site is unsafe and dangerus. Only trained and authrized persnnel shuld be permitted t perate a machine. If mre than ne peratr is expected t use a machine at different times in the same wrk shift, they must all be qualified peratrs and are all expected t fllw all safety rules and instructins in the peratr's, safety and respnsibilities manuals. That means every new peratr shuld perfrm a pre-peratin inspectin, functin tests, and a wrk place inspectin befre using the machine. Emergency Stp Push in the red Emergency Stp buttn t the OFF psitin at the grund cntrls r the platfrm cntrls t stp all functins. Repair any functin that perates when either Emergency Stp buttn is pushed in. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 21
Operatr's Manual First Editin Tenth Printing OPERATING INSTRUCTIONS Starting the Engine 1 At the grund cntrls, turn the key switch t the desired psitin. 2 Be sure bth grund and platfrm cntrl red Emergency Stp buttns are pulled ut t the ON psitin. 3 Gasline/LPG mdels: Chse the fuel surce. Grund cntrl panel: Mve the fuel select tggle switch t the desired psitin. Platfrm cntrl panel: Push the fuel select buttn. 4 Push the engine start buttn. If engine fails t start after 15 secnds f cranking, determine cause and repair any malfunctin. Wait 60 secnds befre trying t start again. All mdels: In extreme cld cnditins, 20 F (-6 C) and belw, warm engine fr 5 minutes befre perating t prevent hydraulic system damage. Gasline/LPG mdels: In extreme cld cnditins, 20 F (-6 C) and belw, machine shuld be started n gasline, then switched t LPG. When perating the machine in gasline mde, use the chke as necessary. Operatin Frm Grund 1 Turn the key switch t grund cntrl. 2 Pull ut bth grund and platfrm red Emergency Stp buttns t the ON psitin. 3 Start the engine. T Psitin Platfrm 1 Hld the functin enable switch t either side. 2 Mve the up/dwn tggle switch accrding t the markings n the cntrl panel. Drive and steer functins are nt available frm the grund cntrls. Operatin Frm Platfrm 1 Turn the key switch t platfrm cntrl. 2 Pull ut the grund and platfrm red Emergency Stp buttn t the ON psitin. 3 Start the engine. T Psitin Platfrm 1 Mve and hld a functin enable/speed select switch. 2 Activate the platfrm up/dwn functin tggle switch in the desired directin f travel. T Steer 1 Press and hld the functin enable switch. 2 Turn the steer wheels with the thumb rcker switch lcated n the tp f the cntrl handle. T Drive 1 Press and hld the functin enable switch. 2 Increase speed: Slwly mve the cntrl handle ff center. Decrease speed: Slwly mve the cntrl handle tward center. Stp: Return the cntrl handle t center r release the functin enable switch. Use the clr-cded directin arrws n the platfrm cntrls and n the platfrm t identify the directin the machine will travel. Machine travel speed is restricted when the platfrm is raised. Drive Select Switch Machine n incline symbl: Lw range peratin fr inclines 22 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual OPERATING INSTRUCTIONS T Extend and Retract Platfrm (Manual Platfrm Extensin) 1 Lift the platfrm extensin lck handle t the hrizntal psitin. 2 Push the platfrm extensin lck handle t extend the platfrm t the desired psitin. D nt stand n the platfrm extensin while trying t extend it. 3 Lwer the platfrm extensin lck handle. GS-2668RT mdels: The platfrm extensin limit switch (if equipped) will disable the drive functin when the platfrm is extended and the platfrm is raised abve 20 ft (6.1 m). Lwer the platfrm r retract the platfrm extensin t drive the machine. GS-3268RT mdels: The platfrm extensin limit switch will disable the drive functin when the platfrm is extended and the platfrm is raised abve 26 ft (7.9 m). Lwer the platfrm r retract the platfrm extensin t drive the machine. T Extend and Retract Platfrm (Pwered Platfrm Extensin - ptin) 1 Press and hld the platfrm extend/retract enable buttn. 2 Mve the cntrl handle in the blue directin t extend the platfrm r in the yellw directin t retract the platfrm. GS-2668RT mdels: The platfrm extensin limit switch (if equipped) will disable the drive functin when the platfrm is extended and the platfrm is raised abve 20 ft (6.1 m). Lwer the platfrm r retract the platfrm extensin t drive the machine. GS-3268RT mdels: The platfrm extensin limit switch will disable the drive functin when the platfrm is extended and the platfrm is raised abve 26 ft (7.9 m). Lwer the platfrm r retract the platfrm extensin t drive the machine. Operatin Frm Grund with Cntrller Maintain safe distances between peratr, machine and fixed bjects. Be aware f the directin the machine will travel when using the cntrller. Engine Stp Buttn Press the engine stp buttn t turn ff the engine. The dwn functin and the hrn will still perate. After Each Use 1 Select a safe parking lcatin firm level surface, clear f bstructins and traffic. 2 Lwer the platfrm. 3 Turn the key switch t the ff psitin and remve the key t secure frm unauthrized use. 4 Chck the wheels. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 23
Operatr's Manual First Editin Tenth Printing OPERATING INSTRUCTIONS Manual Cntrl Outriggers (if equipped) An utrigger ptin is available fr Genie GS-2668RT and GS-3268RT mdels that can be installed in the field. The utriggers are perated frm a cntrl bx munted utside f the platfrm. These instructins apply t this additinal cntrl bx. 1 Psitin machine belw the desired wrk area. 2 Pull ut the red Emergency Stp buttns at the grund and platfrm cntrls. Als pull ut the red Emergency Stp buttn n the utrigger cntrl panel. 3 Activate the utrigger raise/lwer tggle switches and adjust t level the machine and raise the wheels slightly ff the grund. Use the bubble level lcated n the cntrl bx munt. Each tggle switch perates tw utriggers. 4 Raise the platfrm. If the tilt alarm sunds, fully lwer the platfrm and adjust the utriggers. Use the bubble level lcated n the cntrl bx munt. The red indicatr light abve the lift symbl n the utrigger cntrl panel cmes n when ne but nt all utriggers are dwn. All drive and lift functins are disabled. The light turns ff when all utriggers are in firm cntact with the grund. The drive functin is disabled while the utriggers are dwn. If yu try t perate a functin that is lcked ut, the fault light n the platfrm cntrl panel will cme n and the machine will be disabled. This will happen even if the utriggers are in firm cntact with the grund and the red indicatr light n the utrigger cntrl bx is ff. Aut Level Outriggers (if equipped) These instructins apply t machines with the black aut level utrigger cntrl bx. 1 Psitin machine belw the desired wrk area. 2 Pull ut the red Emergency Stp buttns at the grund and platfrm cntrls. 3 Push and hld the aut level buttn. 4 Activate the utrigger up/dwn tggle switch in the dwn directin. Result: The utriggers will extend and level the machine. A beep will sund when the machine is level. The red indicatr light abve the lift symbl n the utrigger cntrl panel cmes n when ne but nt all utriggers are dwn. All drive and lift functins are disabled. The light turns ff when all utriggers are in firm cntact with the grund. The drive functin is disabled while the utriggers are dwn. T cntrl individual utriggers 1 Push and hld the utrigger functin enable buttn. 2 Push and hld an utrigger buttn. 3 Activate the utrigger up/dwn tggle switch in the desired directin t level the machine. Psitining machine n a slpe When setting the machine up n a slpe, the steer-end utriggers must be lwered first. T perate the machine, push in the red Emergency Stp buttn and then pull it ut t ON psitin. Restart the machine. 24 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual Transprt Instructins Brake Release Operatin 1 Chck wheels t prevent machine frm rlling. Observe and Obey: Cmmn sense and planning must be applied t cntrl the mvement f the machine when lifting it with a crane. Transprt vehicle must be parked n a level surface. Transprt vehicle must be secured t prevent rlling while machine is being laded. Be sure vehicle capacity, lading surfaces and chains r straps are sufficient t withstand machine weight. See Specificatins sectin. 2 Be sure winch line is prperly secured t drive chassis tie pints and path is clear f all bstructins. 3 Turn the brake release knb cunterclckwise t pen the brake valve. 4 Pump the brake release pump knb. After machine is laded: 1 Chck wheels t prevent machine frm rlling. 2 Turn the brake release knb clckwise t reset the brakes. Twing the Genie GS-2668 RT r the GS-3268 RT is nt recmmended. If the machine must be twed, d nt exceed 2 mph (3.2 km/h). Machine must be n level surface r secured befre releasing brakes. Securing t Truck r Trailer fr Transit Always chck machine wheels in preparatin fr transprt. Use tie-dwn pints n chassis fr anchring dwn t transprt surface. Use chains r straps f ample lad capacity. Turn key switch t the OFF psitin and remve key befre transprting. Inspect entire machine fr lse r unsecured items. Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 25
Operatr's Manual First Editin Tenth Printing Flr Lading Fundamentals The flr lading sectin prvides infrmatin abut tw specific pressures impsed by the machine n lad-bearing surfaces. Lcalized Pressure (per tire) This measurement is f cncern where the flr surface under the machine must be prtected frm damage resulting frm high pressure being exerted n a small area. Additinal Flr Lading Infrmatin Mdel Occupied Pressure GS-2668 RT GVW + Rated Lad 7800 lbs 3538 kg Axle lad, maximum 4120 lbs 1868 kg Wheel lad, maximum 2060 lbs 934 kg Mdel GS-3268 RT GVW + Rated Lad 8520 lbs 3865 kg Axle lad, maximum 3940 lbs 1787 kg Wheel lad, maximum 1970 lbs 893 kg This measurement is f cncern where the machine is being used n a beam-supprted flr r surface. The ccupied pressure impsed by the machine must nt exceed what the flr r surface can supprt. 26 Genie GS-2668 RT & Genie GS-3268 RT Part N. 48735
First Editin Tenth Printing Operatr's Manual Decals Decal Inspectin Use the pictures n the next page t verify that all decals are legible and in place. Belw is a numerical list with quantities and descriptins. Part N. Descriptin Quantity 25994 Cautin - Cmpnent Damage 1 28157 Label - Dexrn 1 28158 Label - Unleaded (Gasline/LPG mdels) 1 28159 Label - Diesel (Diesel mdels) 1 28160 Label - LPG (Gasline/LPG mdels) 1 (1 additinal with extra LPG tank ptin) 28164 Ntice - Hazardus Materials 1 28171 Label - N Smking 1 28174 Pwer t Platfrm, 230V 2 28175 Cautin - Cmpartment Access 1 28176 Ntice - Missing Manuals 1 28235 Pwer t Platfrm, 115V 2 28236 Warning - Failure T Read... 1 31060 Danger - D Nt Alter Limit Switch 2 40434 Label - Lanyard Anchrage 2 43091 Danger - General Safety Rules 2 43618 Label - Directinal arrws 1 43619 Label - Safety Arm 1 43696 Danger - Electrcutin Hazard 2 44220 Danger/Ntice - Brake Release Safety & Operating Instructins 1 44255 Danger - Crushing Hazard 4 44736 Danger - Tilt Alarm 1 48694 Platfrm Cntrl Panel, Gas/LPG mdels 1 48695 Platfrm Cntrl Panel, Diesel mdels 1 48705 Grund Cntrl Panel 1 49911 Ntice - Maximum Capacity 1200/300 lbs - GS-2668 RT & DC 1 52069 Ntice - Operating Instructins - Grund 1 52070 Ntice - Tire Specificatins 4 52071 Ntice - Kubta Gas Engine Specs 1 52072 Ntice - Kubta Diesel Engine Specs 1 52073 Ntice - Operating Instructins - Platfrm 1 Part N. Descriptin Quantity 52324 Label - Up/Dwn & Functin Enable 1 52431 Label, Grund Cntrl Panel 1 52458 Serial Plate - CE 1 52475 Label - Transprt Tie-dwn 4 52494 Cautin - Crushing Hazard - Rails 1 52523 Serial Plate - ANSI & CSA 1 52617 Label - Manual Lwering Valve 1 52673 Ntice - Max Side Frce, ANSI & CSA - GS-2668 RT & DC 1 52674 Ntice - Max Side Frce, CE - GS-2668 RT & DC 1 52682 Ntice - Maximum Capacity 1000/300 lbs - GS-3268 RT & DC 1 52802 Ntice - Max Side Frce, ANSI & CSA - GS-3268 RT & DC 1 52803 Ntice - Max Side Frce, CE - GS-3268 RT & DC 1 52805 Ntice - Platfrm Extensin Cut-ut - GS-3268 RT & DC 1 52967 Csmetic - 4x4 2 62059 Csmetic - Genie GS-2668 RT 2 62060 Csmetic - Genie GS-3268 RT 2 65053 Label - Fault Cdes 1 71245 Platfrm Cntrl Panel, Gas/LPG mdels, Autmatic Outriggers 1 71246 Platfrm Cntrl Panel, Diesel mdels, Autmatic Outriggers 1 72175 Outrigger Cntrl Panel, Manual 1 72185 Cautin - Crushing Hazard 1 72186 Cautin - Crushing Hazard 4 72187 Danger - Safety and Instructins, Manual 1 72197 Danger - Safety and Instructins, Autmatic 1 Part N. 48735 Genie GS-2668 RT & Genie GS-3268 RT 27